Front and rear panels | Review the Catalyst Center Appliance Features | Cisco Catalyst Center Second-Generation Appliance Installation Guide, Release 3.1.x

Information about the Catalyst Center appliance front and rear panels.

The following figures and tables describe the front and rear panels of the Catalyst Center appliance.

Note

If you are viewing this guide on cisco.com, click any of its figures to view a full-sized version.

Figure 1. 44- and 56-core appliance front panel


Component	Description
1	A total of 10 drives are available on the appliance: Two 480 GB SAS SSD (in slots 1 and 2). Eight 1.9 TB SATA SSD (in slots 3 through 10). Each installed drive has a fault LED and an activity LED. When the drive fault LED is: Off: The drive is operating properly. Amber: The drive has failed. Amber, blinking: The drive is rebuilding. When the drive activity LED is: Off: There is no drive in the sled (no access, no fault). Green: The drive is ready. Green, blinking: The drive is reading or writing data.
2	Power button/power status LED. When the LED is: Off: There is no AC power to the appliance. Amber: The appliance is in standby power mode. Power is supplied only to the Cisco Integrated Management Controller (Cisco IMC) and some motherboard functions. Green: The appliance is in main power mode. Power is supplied to all the server components.
3	Unit identification button and LED. When the LED is: Off: Unit identification is inactive. Blue: Unit identification is active.
4	System status LED. When the LED is: Green: The appliance is running in a normal operating condition. Green, blinking: The appliance is performing system initialization and memory checks. Amber, steady: The appliance is in a degraded operational state, which may be due to one or more of the following causes: Power supply redundancy is lost. CPUs are mismatched. At least one CPU is faulty. At least one DIMM is faulty. At least one drive in a RAID configuration failed. Amber, 2 blinks: There is a major fault with the system board. Amber, 3 blinks: There is a major fault with the memory DIMMs. Amber, 4 blinks: There is a major fault with the CPUs.
5	Power supply status LED. When the LED is: Green: All power supplies are operating normally. Amber, steady: One or more power supplies are in a degraded operational state. Amber, blinking: One or more power supplies are in a critical fault state.
6	Fan status LED. When the LED is: Green: All fan modules are operating properly. Amber, steady: One fan module has failed. Amber, blinking: Critical fault, two or more fan modules have failed.
7	Network link activity LED. When the LED is: Off: The Ethernet link is idle. Green, blinking: One or more Ethernet LOM ports are link-active, with activity. Green: One or more Ethernet LOM ports are link-active, but there is no activity.
8	Temperature status LED. When the LED is: Green: The appliance is operating at normal temperature. Amber, steady: One or more temperature sensors have exceeded a warning threshold. Amber, blinking: One or more temperature sensors have exceeded a critical threshold.
9	Pull-out asset tag.
10	KVM connector. Used with a KVM cable that provides two USB 2.0, one VGA, and one serial connector.

Figure 2. 112-core appliance front panel


Component	Description
1	Power button/power status LED. When the LED is: Off: There is no AC power to the appliance. Amber: The appliance is in standby power mode. Power is supplied only to the Cisco IMC and some motherboard functions. Green: The appliance is in main power mode. Power is supplied to all the server components.
2	Unit identification button and LED. When the LED is: Off: Unit identification is inactive. Blue: Unit identification is active.
3	System status LED. When the LED is: Green: The appliance is running in a normal operating condition. Amber, steady: The appliance is in a degraded operational state, which may be due to one or more of the following causes: Power supply redundancy is lost. CPUs are mismatched. At least one CPU is faulty. At least one DIMM is faulty. At least one drive in a RAID configuration failed. Amber, blinking: The appliance is in a critical fault state, which may be due to one or more of the following causes: Boot failure Fatal processor and/or bus error detected Over-temperature condition
4	Fan status LED. When the LED is: Green: All fan modules are operating properly. Amber, steady: Fan modules are in a degraded state. One fan module has a fault. Amber, blinking: Two or more fan modules have faults.
5	Temperature status LED. When the LED is: Green: The appliance is operating at normal temperature. No error conditions detected. Amber, steady: One or more temperature sensors have exceeded a warning threshold. Amber, blinking: One or more temperature sensors have exceeded a critical non-recoverable threshold.
6	Power supply status LED. When the LED is: Green: All power supplies are operating normally. Amber, steady: One or more power supplies are in a degraded operational state. Amber, blinking: One or more power supplies are in a critical fault state.
7	Network link activity LED. When the LED is: Off: The Ethernet LOM port link is idle. Green: One or more Ethernet LOM ports are link-active, but there is no activity. Green, blinking: One or more Ethernet LOM ports are link-active, with activity.
8	A total of 20 drives are available on the appliance: Two 480 GB SATA SSD (in drive bays 1 and 2). Sixteen 1.9 TB SATA SSD (in slots 3 through 18). Two 3.8 TB SATA SSD (in drive bays 19 and 20). Note Drive bays 21 through 24 are not used by the appliance. Each installed drive has a fault LED and an activity LED. When the drive fault LED is: Off: The drive is operating properly. Amber: The drive has failed. Amber, blinking: The drive is rebuilding. When the drive activity LED is: Off: There is no drive in the sled (no access, no fault). Green: The drive is ready. Green, blinking: The drive is reading or writing data.
9	KVM connector. Used with a KVM cable that provides two USB 2.0, one VGA, and one serial connector.
10	Pull-out asset tag.
11	CPU module bay 1.
12	CPU module bay 2.

Figure 3. 44- and 56-core appliance rear panel

Note

If NIC bonding has been enabled on your Catalyst Center appliance, two instances of the Enterprise, Intracluster, Management, and Internet port are available to configure and use. See NIC bonding overview for more information.


Callout	Description
1	Modular LAN-on-motherboard (mLOM) card bay (x16 PCIe lane)
2	Two USB 3.0 ports
3, 10	1-Gbps/10-Gbps Management Port (Network Adapter 3): This Ethernet port can support 1 Gbps and 10 Gbps, depending on the link partner capability. It is identified as Network Adapter 3 in the Maglev Configuration wizard. Connect this port to a switch that provides access to your enterprise management network. The primary instance (callout 3) is labeled 1 on the rear panel. The secondary instance (callout 10) is the fourth port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 2. This port has a link status LED and a link speed LED. When the status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
4, 11	1-Gbps/10-Gbps Internet Port (Network Adapter 4): This Ethernet port can support 1 Gbps and 10 Gbps, depending on the link partner capability. It is identified as Network Adapter 4 in the Maglev Configuration wizard. This port is optional and is used for connecting to the Internet when it is not possible to do so via the 10-Gbps Enterprise port. Connect to the Internet or a proxy server that has connections to the Internet. The primary instance (callout 4) is labeled 2 on the rear panel. The secondary instance (callout 11) is the third port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 2. This port has a link status LED and a link speed LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
5	VGA video port (DB-15).
6	1-Gbps Cisco IMC Port: This is the embedded port to the right of the VGA video port and to the left of the RJ45 serial port. It is assigned an IP address when you enable browser access to the appliance's Cisco IMC GUI (see Enable Browser Access to Cisco Integrated Management Controller). This port is reserved for out-of-band management of the appliance chassis and software. Connect this port to a switch that provides access to your enterprise management network. This port has a link status LED and a link speed LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
7	Serial port (RJ-45 connector)
8	Rear unit identification button and LED
9	Power supplies (up to two: redundant as 1+1). Each power supply has a power supply fault LED and an AC power LED. When the fault LED is: Off: The power supply is operating normally. Amber, blinking: An event warning threshold has been reached, but the power supply continues to operate. Amber, solid: A critical fault threshold has been reached, causing the power supply to shut down (for example, a fan failure or an over-temperature condition). When the AC Power LED is: Off: There is no AC power to the power supply. Green, solid: AC power is OK, DC output is OK. Green, blinking: AC power is OK, DC output is not enabled. For more details, see Power specifications.
12, 15	10-Gbps Enterprise Port (Network Adapter 1): This port is identified as Network Adapter 1 in the Maglev Configuration wizard. Connect it to a switch with connections to the Enterprise network. The primary instance (callout 15) is the left-hand port on the Intel X710-DA2 NIC in the appliance's PCIe riser 1/slot 1. The secondary instance (callout 12) is the second port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 2. This port has a link status (ACT) LED and a link speed (LINK) LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 100 Mbps or less. Green: Link speed is 10 Gbps. Amber: Link speed is 1 Gbps. Note Although capable of operating at lower speeds, this port is intended to operate at 10 Gbps only.
13, 14	10-Gbps Intracluster Port (Network Adapter 2): This port is identified as Network Adapter 2 in the Maglev Configuration wizard. Connect this port to a switch with connections to the other nodes in the cluster. The primary instance (callout 14) is the right-hand port on the Intel X710-DA2 NIC in the appliance PCIe riser 1/slot 1. The secondary instance (callout 13) is first port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 2. This port is located on the Intel X710-DA4 NIC, which is located in the appliance's PCIe riser 2/slot 2. This port has a link status (ACT) LED and a link speed (LINK) LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the link speed LED is: Off: Link speed is 100 Mbps or less. Green: Link speed is 10 Gbps. Amber: Link speed is 1 Gbps. Note Although capable of operating at lower speeds, this port is intended to operate at 10 Gbps only.
16	Threaded holes for dual-hole grounding lug.

Figure 5. 112-core appliance rear panel slots

Note

If NIC bonding has enabled on your Catalyst Center appliance, two instances of the Enterprise, Intracluster, Management, and Internet port are available to configure and use. See NIC bonding overview for more information.


Callout	Description
1	Serial port COM 1 (DB-9 connector)
2	VGA video port (DB-15 connector)
3	Not used at this time
4, 13	1-Gbps/10-Gbps Management Port (Network Adapter 3): This Ethernet port can support 1 Gbps and 10 Gbps, depending on the link partner capability. It is identified as Network Adapter 3 in the Maglev Configuration wizard. Connect this port to a switch that provides access to your enterprise management network. The primary instance (callout 4) is labeled 1 on the rear panel. The secondary instance (callout 13) is the top port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 12. This port has a link status LED and a link speed LED. When the status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
5, 12	1-Gbps/10-Gbps Internet Port (Network Adapter 4): This Ethernet port can support 1 Gbps and 10 Gbps, depending on the link partner capability. It is identified as Network Adapter 4 in the Maglev Configuration wizard. This port is optional and is used for connecting to the Internet when it is not possible to do so via the 10-Gbps Enterprise port. Connect to the Internet or a proxy server that has connections to the Internet. The primary instance (callout 5) is labeled 2 on the rear panel. The secondary instance (callout 12) is the second port from the top on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 12. This port has a link status LED and a link speed LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
6	1-Gbps Cisco IMC Port: This is the 10/100/1000 Ethernet dedicated management port (Base-T), which is located to the right of the Management port. It is identified as 3 on the rear panel. This port is assigned an IP address when you enable browser access to the appliance's Cisco IMC GUI (see Enable Browser Access to Cisco Integrated Management Controller). It is reserved for out-of-band management of the appliance chassis and software. Connect this port to a switch that provides access to your enterprise management network. This port has a link status LED and a link speed LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 10 Mbps or less. Green: Link speed is 1 Gbps. Amber: Link speed is 100 Mbps.
7	Rear identification button/LED
8	Three USB 3.0 ports
9	Power supplies 1 – 4: hot-swappable and redundant as 3+1 (configured in Cisco IMC). See Power specifications for more information.
10, 15	10-Gbps Intracluster Port (Network Adapter 2): This port is identified as Network Adapter 2 in the Maglev Configuration wizard. Connect this port to a switch with connections to the other nodes in the cluster. The primary instance (callout 15) is the bottom port on the Intel X710-DA2 NIC in the appliance PCIe riser 1/slot 9. The secondary instance (callout 10) is the bottom port on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 12. This port has a link status (ACT) LED and a link speed (LINK) LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the link speed LED is: Off: Link speed is 100 Mbps or less. Green: Link speed is 10 Gbps. Amber: Link speed is 1 Gbps. Note Although capable of operating at lower speeds, this port is intended to operate at 10 Gbps only.
11, 16	10-Gbps Enterprise Port (Network Adapter 1): This port is identified as Network Adapter 1 in the Maglev Configuration wizard. If NIC bonding is enabled on your appliance, connect this port to a switch with connections to the enterprise network. The primary instance (callout 16) is the top port on the Intel X710-DA2 NIC in the appliance PCIe riser 1/slot 9. The secondary instance (callout 11) is the third port from the top on the Intel X710-DA4 NIC in the appliance's PCIe riser 2/slot 12. This port has a link status (ACT) LED and a link speed (LINK) LED. When the link status LED is: Off: No link is present. Green, blinking: Traffic is present on the active link. Green: Link is active, but there is no traffic present. When the speed LED is: Off: Link speed is 100 Mbps or less. Green: Link speed is 10 Gbps. Amber: Link speed is 1 Gbps. Note Although capable of operating at lower speeds, this port is intended to operate at 10 Gbps only.
14	Threaded holes for dual-hole grounding lug.