Cisco Catalyst Center Second-Generation Appliance Installation Guide, Release 3.1.x

PDF

Cisco Catalyst Center Second-Generation Appliance Installation Guide, Release 3.1.x

Enable browser access to the Cisco Integrated Management Controller

Updated: June 5, 2026

Want to summarize with AI?

Log in

Describes how to use the Cisco IMC configuration utility to configure a Catalyst Center appliance's Cisco IMC port.

After installing the appliance, as described in Appliance installation workflow, use the Cisco IMC configuration utility to assign an IP address and gateway to the appliance's CIMC port. This gives you access to the Cisco IMC GUI, which you should use to configure the appliance.

After you complete the Cisco IMC setup, log in to Cisco IMC and run the tasks listed in Execute preconfiguration checks to ensure correct configuration.

Tip

To help ensure the security of your deployment, Cisco IMC prompts you to change the Cisco IMC user's default password when you boot the appliance for the first time. To change the Cisco IMC user password later, use the Cisco IMC GUI, as follows:

  1. From the top-left corner of the GUI, click the Toggle Navigation icon () and then choose Admin > User Management.

    The Local User Management tab should already be selected.

  2. Check the check box for user 1, and then click Modify User.

    The Modify User Details dialog box opens.

  3. Check the Change Password check box.

  4. Enter and confirm the new password, and then click Save.

Procedure

1.

Access the appliance console by attaching either of the following:

  • A KVM cable to the KVM connector on the appliance's front panel (component 11 on the front panel illustrated in Front and rear panels).
  • A keyboard and monitor to the USB and VGA ports on the appliance's rear panel (components 2 and 5, respectively, on the rear panel illustrated in Front and rear panels).
2.

Make sure that the appliance's power cord is plugged in and the power is on.
3.

Press the Power button on the front panel to boot the appliance.

Cisco IMC configuration utility boot screen.

The Cisco IMC configuration utility boot screen should be displayed, as shown below.
4.

As soon as the boot screen is displayed, press F8 to perform Cisco IMC configuration.

The CIMC configuration utility displays the CIMC User Details screen, as shown below.


CIMC User Details screen.

5.

Enter the default CIMC user password (the default on a new appliance is password) in the Enter current CIMC Password field.
6.

Enter and confirm the new CIMC user password in the Enter new CIMC password and Re-Enter new CIMC password fields.

When you press Enter after entering the new password in the Re-Enter new CIMC password field, the Cisco IMC configuration utility displays the NIC Properties screen, as shown below.

NIC Properties screen.
7.

Perform the following actions:

  • NIC mode: Select Dedicated.

  • IP (Basic): Select IPV4.

  • CIMC IP: Enter the IP address of the CIMC port.

  • Prefix/Subnet: Enter the subnet mask for the CIMC port IP address.

  • Gateway: Enter the IP address of your preferred default gateway.

  • Pref DNS Server: Enter the IP address of your preferred DNS server.

  • NIC Redundancy: Select None.
8.

Press F1 to specify Additional settings.

The Cisco IMC configuration utility displays the Common Properties screen, as shown below.

Common Properties screen.
9.

Perform the following actions:

  • Hostname: Enter a hostname for CIMC on this appliance.

  • Dynamic DNS: Uncheck the check box to disable this feature.

  • Factory Defaults: Uncheck the check box to disable this feature.

  • Default User (Basic): Leave these fields blank.

  • Port Properties: Enter new settings or accept the defaults shown in these fields.

  • Port Profiles: Uncheck the check box to disable this feature.

10.

Press F10 to save the settings.

11.

Press Escape to exit and reboot the appliance.

12.

After the settings are saved and the appliance finishes rebooting, open a compatible browser on a client machine with access to the subnet on which the appliance is installed, and enter the following URL:

https://CIMC_ip_address, where CIMC_ip_address is the Cisco IMC port IP address that you entered in Step 7.

Your browser displays a main Cisco IMC GUI login window similar to the one shown below.

Cisco IMC login window.
13.

Log in using the Cisco IMC user ID and password you set in Step 5.

If the login is successful, your browser displays a Cisco Integrated Management Controller Chassis Summary window similar to the one shown below.

Cisco Integrated Management Controller Chassis Summary window.
14.

Confirm that this version of Cisco IMC is supported by the Catalyst Center release you're going to install:

  1. Note the version listed in the Firmware Version field.

  2. See the release notes for the Catalyst Center release you are installing. The “Supported Firmware” section indicates the Cisco IMC version that your Catalyst Center release supports.

  3. Do one of the following: