Upgrading the Cisco cBR-8 Router System to Cisco IOS XE Dublin 17.15.1w


Note

Starting from Cisco IOS XE Bengaluru 17.6.1a, CBR-CCAP-LC-G2-R can only protect CBR-CCAP-LC-G2-R for linecard HA.

Note

If you are using TACACS authentication, the TACACS configuration is automatically updated to the new version after upgrading to Cisco IOS XE Dublin 17.15.1w. This is a fix to CSCvu62273 and you do not need to take any action regarding the TACACS configuration in the cBR-8 prior to the upgrade.

This section contains the upgrade procedures for the Cisco cBR-8 Router System.

By default, telnet is disabled on Cisco cBR-8. If you are going to use telnet to access the device, make sure the value of line vty transport is correct and save the configuration in order to enable telnet. 

Router# show run | begin line vty
line vty 0 4
 exec-timeout 0 0
 privilege level 15
 password 7 104D081B094410055F
 exec prompt timestamp
 transport input all
line vty 5 98
 exec-timeout 0 0
 privilege level 15
 password 7 02050D480809
 transport input all
line vty 99
 transport input all
!

The following table encompasses all versions are required to update to support Cisco IOS XE Dublin 17.15.1w. All other firmware versions are either not upgradable by the customer, or not required to be upgraded for Cisco IOS XE Dublin 17.15.1w support. Use the commands in the tables to verify the firmware versions. If you need to upgrade firmware first, refer to the steps in Upgrading the Cisco cBR-8 Router Firmware.


Note

If you want to upgrade Supervisor CPLD firmware, refer to Upgrading Supervisor CPLD Firmware.

Table 1. Firmware Versions

Internal Name

Component Name

Required Minimum Version

Command

Supervisor CPLD

CBR-CCAP-SUP-160G CPLD

16052011/19071712

 show platform

CBR-CCAP-SUP-250G CPLD

170724E0/190717E1

 show platform

Supervisor ROMMON

CBR-CCAP-SUP-160G ROMMON and CBR-CCAP-SUP-250G ROMMON

16.7(9r)S

 show platform

Line Card CPLD

CBR-CCAP-LC-40G CPLD

00000026

 show platform diag

Docsis 3.1 downstream module Micro

CBR-CCAP-LC-40G Gemini2 Micro

3.1A

 show platform diag

Docsis 3.1 downstream module FPGA

CBR-CCAP-LC-40G Gemini2 Apollo

4.484F

 show platform diag

DPIC Uboot and FPGA

CBR-DPIC-8X10G Firmware

00010001

 show platform diag

DPIC 100G Uboot and FPGA

CBR-DPIC-2X100G Firmware

00020006

 show platform diag

Note

If the user wants to upgrade Supervisor CPLD to version 19071712 and 190717E1, the chassis must be running with Cisco IOS XE Gibraltar 16.12.1w or later releases.


Note

Cisco recommends that operators upgrade their On-Premise SSM Satellite software versions to v7.x or later releases, to ensure the compatibility with cBR-8.

Upgrading from Cisco IOS XE 16.x and later releases to Cisco IOS XE Dublin 17.15.1w

Prerequisites and Considerations

Manual ROMMON Upgrade

If you are upgrading from Cisco IOS XE Everest 16.8.1 or later, manual ROMMON upgrade is not required.

If you are upgrading from Cisco IOS XE Everest 16.6.x or Cisco IOS XE Fuji 16.7.x to Cisco IOS XE Dublin 17.15.1w, manual ROMMON upgrade is necessary. Refer to the Section Manual ROMMON Upgrade for instructions.

Downstream-Controller Remapping (CBR-CCAP-LC-G2-R with 8x10G DPIC)

Starting with Cisco IOS XE Bengaluru 17.6.1, Cisco introduced a new feature on cBR-8 that provides initial support for 32 Video and 32 DOCSIS service groups per CBR-CCAP-LC-G2-R linecard. However, there are specific configuration considerations when using 8x10G Remote PHY Digital Physical Interface Card (D-PIC) with CBR-CCAP-LC-G2-R linecards.

If you are upgrading from Cisco IOS XE Amsterdam 17.3.1 or earlier, and you are using 8x10G Remote PHY Digital Physical Interface Card (D-PIC) with CBR-CCAP-LC-G2-R linecards, see the section entitled Downstream-Controller Remapping (CBR-CCAP-LC-G2-R with 8x10G DPIC) below. Further, it is recommended that you contact your local Cisco representative for assistance before upgrading to Cisco IOS XE Dublin 17.15.1w.

Upgrading using reload

Upgrading from 17.6.1y or Earlier Images

If upgrading from 17.6.1y or earlier, you must copy .pkg files individually to the cBR-8. The tarball below contains all 20 packages and the packages.conf file that are required for upgrading. Before upgrading the system, make sure the following requirements are met:

Procedure

Step 1

Create a new folder on the cBR-8: harddisk:XE-1715-1w. 

mkdir harddisk:XE-1715-1w

Step 2

Create a new folder on the cBR-8: stby-harddisk:XE-1715-1w. 

mkdir stby-harddisk:XE-1715-1w

Step 3

Copy the .pkg files and packages.conf individually to the cBR-8 from the local server. 

copy <location>/cbrsup-cciomdsup.17.15.01w.SPA.pkg harddisk:/
XE-1715-1w/cbrsup-cciomdsup.17.15.01w.SPA.pkg

Repeat for all .pkg files and packages.conf. There should be 21 files in total.

Step 4

Copy the .pkg files and packages conf individually from harddisk to stby-harddisk: 

copy harddisk:/XE-1715-1w/cbrsup-cciomdsup.17.15.01w.SPA.pkg stby-harddisk:/XE-1715-1w/cbrsup-cciomdsup.17.15.01w.SPA.pkg

Repeat for all .pkg files and packages.conf. There should be 21 files in total.

Step 5

Verify the hardware programmable devices upgrade package against the md5 hash as provided in the Cisco.com Software center.

verify /md5 harddisk:/XE-1715-1w/cbrsup-programmable_firmware.17.15.01w.SPA.pkg

Step 6

Configure the system to boot in sub-package mode.

conf t
no boot system
boot system harddisk:/XE-1715-1w/packages.conf
end

Step 7

Save the configuration

wr mem

Step 8

Reload the system

reload

Upgrading from 17.6.1z or Later Images

Before upgrading the system, make sure the following requirements are met.

  • Download two files from the following Cisco.com Software Center URL.

    https://software.cisco.com/download/home/286283913/type

    • IOS XE Software Version 17.15.01w. cbrsup-universalk9.17.15.01w.SPA.bin

    • IOS XE Hardware Programmable Devices Version 17.15.1w. cbrsup-programmable_firmware.17.15.01w.SPA.pkg

Procedure

Step 1

Copy the Cisco IOS XE Dublin 17.15.1w IOS image to harddisk: and stby-harddisk:.

Note

 

Note Ensure that you have Cisco IOS XE Bengaluru 17.6.1z or later installed before proceeding 


copy <location>/cbrsup-universalk9.17.15.01w.SPA.bin harddisk:
copy <location>/cbrsup-universalk9.17.15.01w.SPA.bin stby-harddisk:

Step 2

Verify the Cisco IOS XE Dublin 17.15.1w IOS image against the md5 hash as provided in the Cisco.com Software center. The md5 hash check may not support images greater than 2 GB in size. 


verify /md5 harddisk:cbrsup-universalk9.17.15.01w.SPA.bin 
verify /md5 stby-harddisk:cbrsup-universalk9.17.15.01w.SPA.bin

Step 3

Copy the hardware programmable devices upgrade package to harddisk: if the file has not been copied already.


copy <location>/cbrsup-programmable_firmware.17.15.01w.SPA.pkg harddisk:

Step 4

Verify the hardware programmable devices upgrade package against the md5 hash as provided in the Cisco.com Software center.

verify /md5 harddisk:cbrsup-programmable_firmware.17.15.01w.SPA.pkg

Step 5

Configurethe system to boot with the Cisco IOS XE Dublin 17.15.1w image.

configure terminal
no boot system
boot system harddisk:cbrsup-universalk9.17.15.01w.SPA.bin
end

Step 6

Save the configuration.

wr mem

Step 7

Reload the system

reload
What to do next

Perform verification test to determine if the upgrade is successful, include.

  • Verify the router is running the new IOS-XE release using show version command.

  • Check facility alarms using show facility-alarm status command.

  • Check the status of the power supplies using show environment power command.

  • Check PS status using show platform hardware slot P<0-5> mcu status command.

  • Complete trace routes to known good off-network IP address using the source address of customer CPE blocks to verify routing is working.

  • Check logs for error messages using show log command.

These show commands may be useful in the verification test.

  • show redundancy

  • show platform

  • show platform diag

  • show environment

  • show redundancy linecard all

  • show isis neighbors

  • show ip ospf neighbor

  • show ip route rip

  • show ip mroute

  • show cops servers

  • show cable modem voice

  • show cable calls

  • show cable metering verbose

  • show cable licenses all

  • show inventory

Upgrading with ISSU for I-CCAP Systems

ISSU from any older Cisco IOS XE release to Cisco IOS XE Dublin 17.15.1w is not supported. If you are upgrading from Cisco IOS XE 17.12.1z2 or an earlier release, you must upgrade the cBR-8 system following the steps in Upgrading using reload.

Upgrading Supervisor CPLD Firmware

Before you begin


Note

If the supervisor SO CPLD version is lower than 1511_1401 (SUP 160) or 15111401 (SUP 250), or, if the supervisor SIO CPLD version is lower than 1511_1301 (SUP 160) or 15111301 (SUP 250), physically power cycle the chassis when upgrading the supervisor CPLD.

Before upgrading the firmware, make sure the following requirements are met:

  • Cisco cBR-8 router is running with Cisco IOS XE Gibraltar 16.12.1w or later releases.

  • 2 supervisors are running in the Cisco cBR-8 router and the redundancy is enabled.

  • Download the file from the following Cisco.com Software Center URL:

    https://software.cisco.com/download/home/286283913/type

    • IOS XE Hardware Programmable Devices Version 17.15.01w: cbrsup-programmable_firmware.17.15.01w.SPA.pkg

  • Console access for both supervisors are required.

  • Copy the new firmware package to the cBR-8 using FTP.

    
copy ftp://<location>/cbrsup-programmable_firmware.17.15.01w.SPA.pkg harddisk:
copy ftp://<location>/cbrsup-programmable_firmware.17.15.01w.SPA.pkg stby-harddisk:

Note

When upgrading SUP0, run the CLI with the R0 setting while controlling SUP0. And when upgrading SUP1, run the CLI with the R1 setting.


Note

This guide assumes SUP0 is in active state and SUP1 is in standby hot state at the beginning.

Perform step 1 to 4 using console connection of active SUP0:

SUMMARY STEPS

  1. Set the config register.
  2. Run the following command to prepare for R0 upgrade.
  3. Run the following command to prepare for R1 upgrade.
  4. If the supervisor ViperSO CPLD version is 15111401 and the supervisor ViperSIO CPLD version is 15111301 on both supervisors, follow step 5 - 11 to do the upgrade. Otherwise proceed to step 12.
  5. Set SUP0 to ROMMON using the following command.
  6. Power cycle the SUP0 to set it to ROMMON.
  7. Boot SUP0 into IOS XE using SUP0 console connection.
  8. Set SUP1 to ROMMON using the following command.
  9. Power cycle the SUP1 to set it to ROMMON.
  10. Boot SUP1 into IOS XE using SUP1 console connection.
  11. Wait for the chassis to become SSO and settled down. Then go to step 16. If you skipped step 5 to 10, perform step 12 to 15.
  12. Reload the system by issuing reload command on the active SUP.
  13. Power cycle both supervisors.
  14. Verify if the new version matches the following on both SUPs.
  15. Boot both SUP0 and SUP1 into IOS XE using SUP0 and SUP1 console.
  16. Once the system is up and running, perform the following checks.

DETAILED STEPS

Step 1

Set the config register.


configure terminal
config-register 0x2102
end
write memory

Step 2

Run the following command to prepare for R0 upgrade. 


upgrade hw-programmable cable R0 viper pkg_name /harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg

On SUP 250, you will see one of the following outputs:

  • It takes 10~20 minutes to upgrade. Console would hung. Please don't do any operation during the upgrade.
You are upgrading Viper firmware using harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg image on SUP0, SUP0 is active.
Upgrade from assigned pkg file harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg
Using viper firmware /tmp/viper/mount/supve_viper_fpga_psirt.bin
Size of Viper Upgrade image: 16777216 bytes
No.of parts: 65536
Upgrading golden image...
65536+0 records in
65536+0 records out
16777216 bytes (17 MB, 16 MiB) copied, 688.873 s, 24.4 kB/s
Upgrading primary image...
65536+0 records in
65536+0 records out
16777216 bytes (17 MB, 16 MiB) copied, 675.19 s, 24.8 kB/s
Viper upgrade clean up 0
Upgrade successfully. Please make sure Rommon version is matched.
Please power cycle the chassis to let the new firmware take effect

  • It takes 10~20 minutes to upgrade. Console would hung. Please don't do any operation during the upgrade.
You are upgrading Viper firmware using harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg image on SUP0, SUP0 is active.
Upgrade from assigned pkg file harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg
The golden viper is not compatible with assigned firmware /tmp/viper/mount/supve_viper_fpga_psirt.bin, no upgrade will be performed
Viper upgrade clean up 2

    Note

     

    This output means the SUP already has the latest version it can support, skip the rest of the steps.

On SUP 160, you will see one of the following outputs:

  • It takes about 10 minutes to upgrade. Console would hung. Please don't do any operation during the upgrade.
You are upgrading Viper firmware using harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg image
Upgrade from assigned pkg file /harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg
Using viper firmware /tmp/viper/mount/viper_fpga.bin
Size of Viper Upgrade image: 16777216 bytes
No.of parts: 65536
65536+0 records in
65536+0 records out
Viper upgrade clean up 0
Upgrade successfully. Please make sure Rommon version is matched.
Please power cycle the chassis to let the new firmware take effect

  • It takes 10~20 minutes to upgrade. Console would hung. Please don't do any operation during the upgrade.
You are upgrading Viper firmware using harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg image on SUP0, SUP0 is active.
Upgrade from assigned pkg file harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg
The golden viper is not compatible with assigned firmware /tmp/viper/mount/supve_viper_fpga_psirt.bin, no upgrade will be performed
Viper upgrade clean up 2

    Note

     

    This output means the SUP already has the latest version it can support, skip the rest of the steps.

Note

 

Do not power cycle the chassis in this step.

Step 3

Run the following command to prepare for R1 upgrade.


upgrade hw-programmable cable R1 viper pkg_name /harddisk/cbrsup-programmable_firmware.17.15.01w.SPA.pkg

You will see the similar output as the one in Step 2.

Note

 

Do not power cycle the chassis in this step.

Step 4

If the supervisor ViperSO CPLD version is 15111401 and the supervisor ViperSIO CPLD version is 15111301 on both supervisors, follow step 5 - 11 to do the upgrade. Otherwise proceed to step 12. 


Router#show platform diag 
Load for five secs: 6%/1%; one minute: 7%; five minutes: 8%
Time source is NTP, 16:05:43.546 PST Thu Feb 8 2018
Chassis type: CBR-8-CCAP-CHASS
<SNIP>
Slot: SUP0, CBR-CCAP-SUP-160G
        Physical insert detect time : 00:01:58 (1d03h ago)
        CPLD version                : 16052011
        ViperSO CPLD version        : 15111401
        ViperSIO CPLD version       : 15111301
        Rommon version              : 16.7(1r)S
        Blackbird version           : 00000112
        Raptor ESI version          : 0001003b
        Raptor MAC version          : 00010031
        SUP-PIC CPLD version        : 14071504
        SUP-DC CPLD version         : 14072207
        DTI Client FPGA version     : 00000005
        DTI Firmware version        : 00000A03
        Cortina PHY version         : 201402061607
        SUP PSOC 0 version          : v4.0.9         
        SUP PSOC 1 version          : v4.0.8         
        SUP PSOC 2 version          : v4.1.0_IVB     
        SUP PSOC 3 version          : v4.0.6         
        SUP-DC PSOC 0 version       : v4.0.8        
        SUP-DC PSOC 1 version       : v4.0.5         
        SUP-PIC PSOC 0 version      : V2.0.6         
        SUP-PIC PSOC 1 version      : V2.0.6         
<SNIP>
Slot: SUP1, CBR-CCAP-SUP-160G
        Physical insert detect time : 00:02:26 (1d03h ago)
        CPLD version                : 16052011
        ViperSO CPLD version        : 15111401
        ViperSIO CPLD version       : 15111301
        Rommon version              : 16.7(1r)S
        Blackbird version           : 00000112
        Raptor ESI version          : 0001003b
        Raptor MAC version          : 00010031
        SUP-PIC CPLD version        : 14071504
        SUP-DC CPLD version         : 14072207
        DTI Client FPGA version     : 00000005
        DTI Firmware version        : 00000A03
        Cortina PHY version         : 201402061607
        SUP PSOC 0 version          : v4.0.9         
        SUP PSOC 1 version          : v4.0.8         
        SUP PSOC 2 version          : v4.1.0_IVB     
        SUP PSOC 3 version          : v4.0.6         
        SUP-DC PSOC 0 version       : v4.0.9        
        SUP-DC PSOC 1 version       : v4.0.5         
        SUP-PIC PSOC 0 version      : V3.0.0         
        SUP-PIC PSOC 1 version      : V3.0.0         
<SNIP>

Step 5

Set SUP0 to ROMMON using the following command.

redundancy force-switchover

Perform the following steps 6 to 7 using console connection of current active SUP1.

Step 6

Power cycle the SUP0 to set it to ROMMON.

test platform hardware slot R0 oir power-cycle

This command will reset and re-initialize the ROMMON. The new version of the supervisor CPLD will now take effect. Verify if it matches the following new version.

SUP 160 new version: 0x19071712

SUP 250 new version: 0x190717E1

Step 7

Boot SUP0 into IOS XE using SUP0 console connection.


dir harddisk:
boot harddisk:cbrsup-universalk9.17.15.01w.SPA.bin

Wait utill SUP0 is in standby hot.

Step 8

Set SUP1 to ROMMON using the following command.

redundancy force-switchover

Perform the following steps 9 to 11 using console connection of current active SUP0.

Step 9

Power cycle the SUP1 to set it to ROMMON.

test platform hardware slot R1 oir power-cycle

This command will reset and re-initialize the ROMMON. The new version of the supervisor CPLD will now take effect. Verify if it matches the following new version.

SUP 160 new version: 0x19071712

SUP 250 new version: 0x190717E1

Step 10

Boot SUP1 into IOS XE using SUP1 console connection.


dir harddisk:
boot harddisk:cbrsup-universalk9.17.15.01w.SPA.bin

Wait utill SUP1 is in standby hot.

Step 11

Wait for the chassis to become SSO and settled down. Then go to step 16. If you skipped step 5 to 10, perform step 12 to 15.

Note

 

You need physical access to the chassis to power cycle the chassis.

Step 12

Reload the system by issuing reload command on the active SUP. 

Router#reload

Step 13

Power cycle both supervisors.

Step 14

Verify if the new version matches the following on both SUPs.

SUP 160 new version: 0x19071712

SUP 250 new version: 0x190717E1

Step 15

Boot both SUP0 and SUP1 into IOS XE using SUP0 and SUP1 console.


dir harddisk:
boot harddisk:cbrsup-universalk9.17.15.01w.SPA.bin

Wait till SUP0 become standby hot.

Step 16

Once the system is up and running, perform the following checks.

  • Set config register to normal boot.

    
configure terminal
config-register 0x2102
end
write memory

  • Execute show redundancy command to ensure both SUPs are listed, one is active and the other is standby hot.

  • Execute show proc CPU sorted | ex 0.00 command.

  • Execute show platform diag command.

Upgrading cBR CCAP 8x10G Remote PHY Digital Physical Interface Card

Before you begin

Before upgrading the system, make sure the following requirements are met:

  • Make sure the latest available IOS XE version is active in Cisco cBR-8 router.

  • There are at lease 20MB free space on the harddisk.


Note

To make use of the new features, it is recommended to upgrade the cBR CCAP 8x10G Remote PHY Digital Physical Interface Card (D-PIC) to the latest version 1.1.

Procedure

Step 1

Boot up system, wait until IOS is ready.

Step 2

Check current D-PIC version.


show hw-module subslot x/1 fpd

Note

 

x/1 is D-PIC subslot number which needs upgrade.

Example:


Router#show hw-module subslot 9/1 fpd

==== ====================== ====== =============================================
                             H/W   Field Programmable   Current   Min. Required
Slot Card Type               Ver.  Device: "ID-Name"    Version      Version
==== ====================== ====== ================== =========== ==============
 9/1 CBR-DPIC-8X10G          1.0   46-CBR DIGI PIC        1.0         1.0
==== ====================== ====== =============================================

Step 3

Upgrade D-PIC.


upgrade hw-module subslot x/1 fpd bundled reload

Example:


Router#upgrade hw-module subslot 9/1 fpd bundled reload

% The following FPD will be upgraded for CBR-DPIC-8X10G (H/W ver = 1.0) in subslot 9/1:

  ================== =========== =========== ============ 
  Field Programmable   Current     Upgrade   Estimated 
  Device: "ID-Name"    Version     Version   Upgrade Time 
  ================== =========== =========== ============ 
  46-CBR DIGI PIC        1.0         1.1       00:05:00
  ================== =========== =========== ============ 

% NOTES:
  - Use 'show upgrade fpd progress' command to view the progress of the FPD
    upgrade.
  - The target card will be automatically reloaded after the upgrade 
    operation. This reload will interrupt normal operation of the card. If 
    necessary, ensure that appropriate actions have been taken to redirect 
    card traffic before starting the FPD upgrade.

% Are you sure that you want to perform this operation? [no]: yes
% Initiating the upgrade operation on the target card ...
  (Use "show upgrade fpd progress" command to see upgrade progress)

Step 4

Check if the upgrade process is finished. Upgrade progress will take about 1 to 2 minutes.


show upgrade fpd progress

Example:

Upgrade still ongoing:

Router#show upgrade fpd progress

FPD Image Upgrade Progress Table:

 ==== =================== ====================================================
                                               Approx.
                          Field Programmable    Time     Elapsed
 Slot Card Type           Device : "ID-Name"   Needed      Time    State
 ==== =================== ================== ========== ========== ===========
  9/1 CBR-DPIC-8X10G      46-CBR DIGI PIC     00:05:00   00:00:13  Updating...
 ==== =================== ====================================================

Router# show upgrade fpd progress

FPD Image Upgrade Progress Table:

 ==== =================== ====================================================
                                               Approx.
                          Field Programmable    Time     Elapsed
 Slot Card Type           Device : "ID-Name"   Needed      Time    State
 ==== =================== ================== ========== ========== ===========
  9/1 CBR-DPIC-8X10G      46-CBR DIGI PIC     00:05:00   00:00:26  Updating...
 ==== =================== ====================================================

Upgrade finished:

Router#show upgrade fpd progress

% There is no FPD image upgrade in progress.

Step 5

Check if the D-PIC status is ready.

show platform

Example:

Router#show platform 
Chassis type: CBR-8-CCAP-CHASS

Slot      Type                State                 Insert time (ago) 
--------- ------------------- --------------------- ----------------- 
2/1       CBR-RF-PROT-PIC     ok                    00:08:48      
3         CBR-CCAP-LC-40G     ok                    00:12:46      
3/1       CBR-RF-PIC          ok                    00:08:48      
8/1       CBR-DPIC-8X10G      ok                    00:07:56      
9         CBR-CCAP-LC-40G     ok                    00:12:46      
9/1       CBR-DPIC-8X10G      ok                    00:07:54      
SUP0      CBR-CCAP-SUP-160G   inserted              00:12:46      
 R0                           ok, active            
 F0                           ok, active            
 4                            ok, active            
 4/1      CBR-SUP-8X10G-PIC   ok                    00:07:55      
SUP1      CBR-CCAP-SUP-160G   inserted              00:12:22      
 R1                           ok, standby           
 F1                           ok, standby           
 5                            ok, standby           
 5/1      CBR-SUP-8X10G-PIC   ok                    00:07:54      
P0        PWR-3KW-AC-V2       ok                    00:09:49      
P1        PWR-3KW-AC-V2       ok                    00:09:49      
P2        PWR-3KW-AC-V2       ps, fail              00:09:49      
P3        Unknown             N/A                   never         
P4        Unknown             N/A                   never         
P5        PWR-3KW-AC-V2       ok                    00:09:49      
P10       CBR-FAN-ASSEMBLY    ok                    00:09:39      
P11       CBR-FAN-ASSEMBLY    ok                    00:09:39      
P12       CBR-FAN-ASSEMBLY    ok                    00:09:39      
P13       CBR-FAN-ASSEMBLY    ok                    00:09:39      
P14       CBR-FAN-ASSEMBLY    ok                    00:09:39      

Slot      CPLD Version        Rommon Version                          
--------- ------------------- --------------------------------------- 
3         00000025            2011.03.18                          
9         00000025            2011.03.18                          
SUP0      16052011            16.7(3r)S                           
SUP1      16052011            16.7(3r)S

Step 6

Check if the new version works.

show hw-module subslot x/1 fpd

Example:

Router#show hw-module subslot 9/1 fpd

==== ====================== ====== =============================================
                             H/W   Field Programmable   Current   Min. Required
Slot Card Type               Ver.  Device: "ID-Name"    Version      Version
==== ====================== ====== ================== =========== ==============
 9/1 CBR-DPIC-8X10G          1.0   46-CBR DIGI PIC        1.1         1.0      
==== ====================== ====== =============================================

Upgrading Uboot For CBR-CCAP-LC-40G

Procedure

Step 1

Copy the package file (cbrsup-programmable_firmware.17.15.1w.SSA.pkg) to the active SUP’s harddisk.

copy <location>/cbrsup-programmable_firmware.17.15.01w.SPA.pkg harddisk:

Step 2

Upgrade Uboot using the following CLI command:

upgrade hw-programmable cable <slot#> rommon pkg_name harddisk/cbrsup-programmable_firmware.17.15.01w.SSA.pkg

Example:

Router#upgrade hw-programmable cable <slot#> rommon pkg_name harddisk/cbrsup-programmable_firmware.17.15.01w.SSA.pkg
UBOOT:
   FILE    : /tmp/fpd/mount/uboot.bin.SPA
   VERSION : U-Boot 2011.03.19
   BYTES   : 1441792
   Upgrade Field Region: SUCCESS! Please reload the card to let the new firmware take effect.

Step 3

Reload Line Card using the following CLI command:

Router#hw-module slot <slot#> reload

Step 4

Check the Uboot version after LC boot up using the following CLI command:

show platform diag

Example:

Router# show platform diag
...
Slot: 1, CBR-CCAP-LC-40G
        Running state               : ok
        Internal state              : online
        Internal operational state  : ok
        Physical insert detect time : 00:03:11 (5d11h ago)
        Software declared up time   : 00:07:46 (5d11h ago)
        CPLD version                : 00000025
        Rommon version              : 2011.03.19
        Basestar version            : 00200057
        Raider version              : 02010019
        dsphy0_fpga version         : 4.484B
        dsphy0_micro version        : 3.1A
        dsphy0_psoc version         : 4.4
        dsphy0_cpld version         : 0.7
        dsphy1_fpga version         : 4.484B
        dsphy1_micro version        : 3.1A
        dsphy1_psoc version         : 4.4
        dsphy1_cpld version         : 0.7
        Caprica version             : 0002000a
        HA-PLL version              : N/A
        PSOC 0 version              : v4.6
        PSOC 1 version              : v4.6
...

Manual ROMMON Upgrade

Before you begin

If you are upgrading from Cisco IOS XE Everest 16.6.x or Cisco IOS XE Fuji 16.7.x to Cisco IOS XE Dublin 17.15.1w, perform the following steps to upgrade SUP ROMMON manually.

Procedure

Step 1

Download hardware programmable devices upgrade package file cbrsup-programmable_firmware.17.15.01w.SPA.pkg from the following Cisco.com Software Center URL: https://software.cisco.com/download/home/286283913/type

Step 2

Verify the hardware programmable devices upgrade package against the md5 hash as provided in the Cisco.com Software center.

verify /md5 harddisk:cbrsup-programmable_firmware.17.15.01w.SPA.pkg

Step 3

Upgrade SUP ROMMON.

Router#upgrade rom-mon file harddisk:cbrsup-programmable_firmware.17.15.01w.SPA.pkg r0
Wait for the following output on the console:
ROMMON upgrade complete.
To make the new ROMMON permanent, you must restart the RP

Router#upgrade rom-mon file harddisk:cbrsup-programmable_firmware.17.15.01w.SPA.pkg r1
Wait for the following output on the console:
ROMMON upgrade complete.
To make the new ROMMON permanent, you must restart the RP

Step 4

Reload both the SUPs.

Downstream-Controller Remapping (CBR-CCAP-LC-G2-R with 8x10G DPIC)

Before you begin

If you are using cBR CCAP 8x10G Remote PHY Digital Physical Interface Card (D-PIC) with CBR-CCAP-LC-G2-R linecards, contact your local Cisco representative before upgrading to Cisco IOS XE Dublin 17.15.1w.

Starting with in Cisco IOS XE Bengaluru 17.6.1, Cisco introduces a new feature on cBR-8 that provides initial support for 32 Video and 32 DOCSIS service groups per CBR-CCAP-LC-G2-R linecard. The implementation of this feature introduces new 8x10G DPIC port mapping constraints on existing 'Downstream-Cable' controllers. Cisco has prepared a python tool that can be used to determine if a cBR-8 running-configuration includes non-compliant controller mappings, and, to update the running-confirguration to be compliant with the latest Cisco IOS XE Dublin 17.15.1w. Once you have the python tool, perform the following steps in order to predict and avoid downtime:

Before you begin: Special considerations must be taken when using SmartPHY. Contact your local Cisco representative if your installation includes SmartPHY.

Procedure

Step 1

Collect the following information from the target cBR-8 to upgrade.


Router#show cable rpd sum
Router#show cable modem sum
Router#show cable video session all sum

Step 2

Save the running configuration to the harddisk of the cBR-8.

Router#copy running-config harddisk:SavedConfig.txt

Step 3

Copy the saved running configuration from harddisk: to an offline server for editing using SCP.

Router#copy harddisk:SavedConfig.txt scp:<path>

Step 4

Run the python tool to modify the controllers in the saved configuration.

  • Option 1 - Renumber Downstream-Cable controllers only

    1. Execute python script kobol_ph2_controller_migration.py. This script is intended for customers who do not immediately intend to take advantage of the Downstream-Video controllers and expanded SG capacity on CBR-CCAP-LC-G2-R. 

      $ python kobol_ph2_controller_migration.py
Enter the name of the configuration file: SavedConfig.txt

    2. Output file appends _remap_controller to the file name. 

      Output file name: SavedConfig.txt_remap_controller

    3. Check to ensure that the script completed successfully. If no output file is created or the size of the output file is 0 byte, then check script output for error messages.

  • Option 2 - Renumber Downstream-Cable and utilize Downstream-Video controllers

    1. Execute python script kobol_ph2_controller_migration_video.py. This script is intended for customers who wish to utilize the new Downstream-Video controllers to free up existing Downstream-Cable controllers for expanded DOCSIS service groups. 

      $ python kobol_ph2_controller_migration_video.py
Enter the name of the configuration file: SavedConfig.txt

    2. Output file appends _remap_controller_video to the file name. 

      Output file name: SavedConfig.txt_remap_controller_video

    3. Check to ensure that the script completed successfully. If no output file is created or the size of the output file is 0 byte, then check script output for error messages.

Step 5

Modify the remapped configuration file to specify the Cisco IOS XE Dublin 17.15.1w image in the boot parameter.

boot system harddisk:cbrsup-universalk9.17.15.01w.SPA.bin

Step 6

Copy the final remapped configuration file back to the cBR-8 harddisk.

Router#copy scp:<path>/SavedConfig.txt_remap_controller harddisk:

or

Router#copy scp:<path>/SavedConfig.txt_remap_controller_video harddisk:

Step 7

Copy remapped configuration file to startup of the cBR-8.

Router#copy harddisk:SavedConfig.txt_remap_controller startup-config

or

Router#copy harddisk:SavedConfig.txt_remap_controller_video startup-config

After performing the remapping procedure, monitor the chassis for any of the following errors after reload:

Mismatches TE interface. DS controller should be */*/0~7, configuration failed.
Mismatches TE interface. DS controller should be */*/8~15, configuration failed.
Mismatches TE interface. DS controller should be */*/16~23, configuration failed.
Mismatches TE interface. DS controller should be */*/24~31, configuration failed.