To verify the configuration of the encryption algorithm on the linecard, use the show cable video encryption linecard command as shown in the example below:
Router# show cable video encryption linecard 7/0
Line card: 7/0
CA System Scrambler DVB-Conformance
===============================================
dvb dvb-csa Enabled
To verify the ECMG connection, use the show cable video encryption dvb ecmg id
id
connection command as shown in the example below:
Router# show cable video encryption dvb ecmg id 1 connection
------------------------------------------------------------------------------------------------------------------------------
ECMG ECMG ECMG CA Sys CA Subsys PID Lower Upper Streams/ Open Streams/ Auto Chan Slot ECMG ECMG
ID Name Type ID ID Source limit limit ECMG ECMG ID Connections Application
------------------------------------------------------------------------------------------------------------------------------
1 polaris_ecmg01 standard 0x4748 0x0 sid 0 0 1 1 Enabled RP 1 Tier-Based
ECMG Connections for ECMG ID = 1
----------------------------------------------------------
Conn Conn IP Port Channel Conn Open
-ID Priority Address Number ID Status Streams
----------------------------------------------------------
1 1 10.10.1.1 8888 1 Open 1
The sample output of the session based scrambling configuration verification command is shown below:
Router# show cable video encryption dvb ecmg id 7 connection
------------------------------------------------------------------------------------------------------------------------------
ECMG ECMG ECMG CA Sys CA Subsys PID Lower Upper Streams/ Open Streams/ Auto Chan Slot ECMG ECMG
ID Name Type ID ID Source limit limit ECMG ECMG ID Connections Application
------------------------------------------------------------------------------------------------------------------------------
7 ecmg-7 standard 0x950 0x1234 sid 0 0 1680 1680 Enabled 7 1 VOD
ECMG Connections for ECMG ID = 1
----------------------------------------------------------
Conn Conn IP Port Channel Conn Open
-ID Priority Address Number ID Status Streams
----------------------------------------------------------
1 1 10.10.1.10 8888 1 Open 1
The status of the connection with the ECMG Server is indicated by the Conn Status. The Open Streams field indicates the number of Active ECM Streams.
To verify the EIS connection, use the show cable video encryption dvb eis id
id command as shown in the example below:
Router# show cable video encryption dvb eis id 1
----------------------------------------------------------------------------------------
EIS EIS Peer Management TCP CP CP Overwrite Fail-To-Clear Connection
ID Name IP IP Port Overrule Duration SCG Duration Status
------------------------------------------------------------------------------------
1 test 10.10.1.11 10.10.1.1 9898 DISABLED 0 DISABLED 400 Connected
To verify the CA Interface configuration in the case of session based scrambling, use the show cable video encryption dvb ca-interface brief command as shown in the example below:
Router# show cable video encryption dvb ca-interface brief
CA Interface configuration
------------------------------
Linecard IP Address VRF
------------------------------
7 10.10.1.1 N/A
ECMG Route configuration
-----------------------------------------------------
IP Address NetMast Interface
-----------------------------------------------------
10.10.1.10 255.255.255.224 TenGigabitEthernet4/1/2
To verify the encryption status of the sessions, use the show cable video session logical-edge-device id command as shown in the example below:
Router# show cable video session logical-edge-device id 1
Total Sessions = 1
Session Output Streaming Session Session Source UDP Output Input Output Input Output Encrypt Encrypt Low Session
Id Port Type Type Ucast Dest IP/Mcast IP (S, G) Port Program State State Bitrate Bitrate Type Status Latency Name
--------------------------------------------------------------------------------------------------------------------------------------------------------------
1048576 1 Remap UDP 10.10.1.1 49167 20 ACTIVE-PSI 1695161 1689747 DVB Encrypted N dvbsess.1.0.1.0.23167
To verify the ECM PID and whether the CA Descriptor is added to the PMT, use the show cable video session logical-edge-device id session-id command as shown in the example below:
Router# show cable video session logical-edge-device id 1 session-id 1048576
Output PMT Info:
==============================
Program 20, Version 3, PCR 49, Info len 18, (CA SYS-ID 4748, PID 79)
PID 49: Type 2, Info len 0
PID 50: Type 3, Info len 6, (lang eng)