Cisco Converged Broadband Routers Video Configuration Guide for Cisco IOS XE Gibraltar 16.10.x

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco Converged Broadband Routers Video Configuration Guide for Cisco IOS XE Gibraltar 16.10.x

Chapter Title

Simple Content Protection Video Session Support

Results

Updated:
February 15, 2019

Chapter: Simple Content Protection Video Session Support

Simple Content Protection Video Session Support

Cisco cBR Converged Broadband routers provide support for Simple Content Protection (SCP) video encryption licensing, which enables third-party products, such as Digital Transport Adapters (DTA), avail the capability of encrypting video streams compatible with Cisco's SCP conditional access (CA) system.

Support for SCP Conditional Access System

Cisco cBR Converged Broadband Router supports uDTA-SCP for broadcast (linear) services and thus removes the need for a bulk encryptor.

SCP is a conditional access system. When a Cisco controller system is combined with an Entitlement Control Message (ECM) generator, along with the licensed encryption device, it enables the Cisco conditional access systems to provide protection for various services. These are services such as linear broadcast (Basic, Expanded Basic, Digital Basic, Premium, PPV, and IPPV), switched digital video (SDV), and on-demand content (VoD).

The Cisco Conditional Access technologies that are enabled by this license include PowerKEY and Simple Content Protection. The technologies are enabled in modes compliant with the existing deployed CPE devices that employ those CA technologies.

Prerequisites

The following are the prerequisites for configuring SCP on Cisco cBR routers:

  • SCP services are configured in DTACS/EC and sessions are configured on SCP-PCG.

  • These multicast session configurations on SCP QAM must be manually configured on the Cisco cBR-8 routers as static table-based sessions.

  • The DCM is configured for SCP scrambling along with the ROSA SI server (AC Manager, SCS configurator, and Scrambling control task).

Configure Cisco cBR Routers for SCP

To configure and enable SCP on Cisco cBR Converged Broadband routers, do the following tasks:

  • Create a Virtual Carrier Group (VCG) with the QAM channel, which carries the SCP content.

  • Create Service Distribution Group (SDG) for SCP.

  • Create VCG-SDG bind.

Create SDG and VCG

To create SDG and VCG, use the following commands:

service-distribution-group service distribution group name ID 
rf-port integrated-cable slot/bay/port
virtual-carrier-group name [id number]
service-type narrowcast
rf-channel start_channel-end_channel tsid start_tsid-end_tsid output-port-number start_number-end_number
bind-vcg
vcg vcg-name sdg sdg-name

Example: Creating SDG and VCG

The following example shows how to create the SDG and the VCG:

service-distribution-group sdg1 id 1
rf-port integrated-cable 1/0/0
virtual-carrier-group vcg1 id 1
service-type narrowcast
rf-channel 20-24 tsid 120-124 output-port-number 120-124
bind-vcg
vcg vcg1 sdg sdg1

Create a Table-based LED for SCP

To create a table-based LED for SCP, use the following commands:

logical-edge-device name id ID
protocol table-based
virtual-edge-input-ip ip-address input-port-number port-number
vcg vcg-name
active

Example: Creating a Table-based LED for SCP

The following example shows how to create a table-based LED:

logical-edge-device led1 id 1
protocol table-based
virtual-edge-input-ip 198.51.100.1 input-port-number 1
vcg vcg1
active

Configure Table-based and PSIP Sessions

Configure table-based sessions with the same output service ID as the one configured in DTACS (service ID) or DCM output service ID (for example, 209). You should also configure PSIP session that carries SI data required for the uDTA box. 

cable video
table-based
vcg vcg-name
rf-channel ID
session sess-name group <IP address> processing-type remap start-program n 
session SESS_PSIP group <IP address> processing-type passthru psip

Example: Configuring Table-based and PSIP Sessions

The following example shows how to configure table-based session and PSIP session:

cable video
table-based
vcg vcg1
rf-channel 21
session SESS_SCP group 203.0.113.1 processing-type remap start-program 209
session SESS_PSIP group 203.0.113.32 processing-type passthru psip

Feature Information for SCP Video Session Support

Use Cisco Feature Navigator to find information about the platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to the www.cisco.com/go/cfn link. An account on the Cisco.com page is not required.


Note

The following table lists the software release in which a given feature is introduced. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Table 1. Feature Information for PMV Support for Table-Based Videos

Feature Name

Releases

Feature Information

SCP Video Session Support

Cisco IOS XE Fuji 16.9.1a

This feature was introduced on the Cisco cBR Series Converged Broadband Router.

Was this Document Helpful?

FeedbackFeedback

Contact Cisco