Cisco cBR Series Converged Broadband Routers Security and Cable Monitoring Configuration Guide for Cisco IOS XE Fuji 16.8.x

Bias-Free Language

The documentation set for this product strives to use bias-free language. For the purposes of this documentation set, bias-free is defined as language that does not imply discrimination based on age, disability, gender, racial identity, ethnic identity, sexual orientation, socioeconomic status, and intersectionality. Exceptions may be present in the documentation due to language that is hardcoded in the user interfaces of the product software, language used based on RFP documentation, or language that is used by a referenced third-party product. Learn more about how Cisco is using Inclusive Language.

Book Contents
Find Matches in This Book
Available Languages
Download Options

Book Title

Cisco cBR Series Converged Broadband Routers Security and Cable Monitoring Configuration Guide for Cisco IOS XE Fuji 16.8.x

Chapter Title

Dynamic Shared Secret

Results

Updated:
March 26, 2015

Chapter: Dynamic Shared Secret

Dynamic Shared Secret

This document describes the Dynamic Shared Secret feature, which enables service providers to provide higher levels of security for their Data-over-Cable Service Interface Specifications (DOCSIS) cable networks. This feature uses randomized, single-use shared secrets to verify the DOCSIS configuration files that are downloaded to each cable modem.

The Dynamic Shared Secret feature automatically creates a unique DOCSIS shared secret on a per-modem basis, creating a one-time use DOCSIS configuration file that is valid only for the current session. This ensures that a DOCSIS configuration file that has been downloaded for one cable modem can never be used by any other modem, nor can the same modem reuse this configuration file at a later time.

This patented feature is designed to guarantee that all registered modems use only the quality of service (QoS) parameters that have been specified by the DOCSIS provisioning system for a particular modem at the time of its registration. This feature is an accepted DOCSIS standard.

Finding Feature Information

Your software release may not support all the features documented in this module. For the latest feature information and caveats, see the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the Feature Information Table at the end of this document.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.

Contents

Hardware Compatibility Matrix for Cisco cBR Series Routers


Note

The hardware components introduced in a given Cisco IOS-XE Release are supported in all subsequent releases unless otherwise specified.

Table 1. Hardware Compatibility Matrix for the Cisco cBR Series Routers

Cisco CMTS Platform

Processor Engine

Interface Cards

Cisco cBR-8 Converged Broadband Router

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 Supervisor :

  • PID—CBR-CCAP-SUP-160G

  • PID—CBR-CCAP-SUP-60G1

  • PID—CBR-SUP-8X10G-PIC

Cisco IOS-XE Release 3.15.0S and Later Releases

Cisco cBR-8 CCAP Line Cards:

  • PID—CBR-LC-8D30-16U30

  • PID—CBR-LC-8D31-16U30

  • PID—CBR-RF-PIC

  • PID—CBR-RF-PROT-PIC

Cisco cBR-8 Downstream PHY Modules:

  • PID—CBR-D30-DS-MOD

  • PID—CBR-D31-DS-MOD

Cisco cBR-8 Upstream PHY Modules:

  • PID—CBR-D30-US-MOD

1 Effective with Cisco IOS-XE Release 3.17.0S, CBR-CCAP-SUP-60G supports 8 cable line cards. The total traffic rate is limited to 60Gbps, the total number of downstream service flow is limited to 72268, and downstream unicast low-latency flow does not count against the limits.

Prerequisites for Dynamic Shared Secret

The configuration of Dynamic Shared Secret feature is supported on the Cisco CMTS routers.

Following is a list of other important prerequisites for the Dynamic Shared Secret feature:

  • The Cisco CMTS must be running Cisco IOS-XE 3.15.0S or later.

  • The Dynamic Shared Secret feature supports an external provisioning server.

  • A cable modem must be able to register with the Cisco CMTS before enabling the Dynamic Shared Secret feature.

  • For full security, DOCSIS configuration files should have filenames that are at least 5 or more characters in length.

  • For best performance during the provisioning of cable modems, we recommend using Cisco Network Registrar Release 3.5 or later.


Note
When the Dynamic Shared Secret feature is enabled using its default configuration, a cable modem diagnostic webpage shows a scrambled name for its DOCSIS configuration file. This filename changes randomly each time that the cable modem registers with the CMTS. To change the default behavior, use the nocrypt option with the cable dynamic-secret command.

Restrictions for Dynamic Shared Secret

General Restrictions for Dynamic Shared Secret

  • Shared-secret and secondary-shared-secret cannot be configured with Dynamic Shared Secret feature.

  • If you configure the Dynamic Shared Secret feature on a primary cable interface, you should also configure the feature on all of the corresponding subordinate cable interfaces.

  • The Dynamic Shared Secret feature ensures that each cable modem registering with the CMTS can use only the DOCSIS configuration file that is specified by the service provider’s authorized Dynamic Host Configuration Protocol (DHCP) and TFTP servers, using the DOCSIS-specified procedures.

  • The Dynamic Shared Secret feature does not affect cable modems that are already online and provisioned. If a cable modem is online, you must reset it, so that it reregisters, before it complies with the Dynamic Shared Secret feature.

  • The DMIC lock mode uses the following behavior during a switchover event in HCCP N+1 Redundancy. All cable modems which were previously in lock mode are taken offline during a switchover event, and the prior state of locked modems is lost. If previously locked modems remain non-compliant, they will return to LOCK mode after three failed registration attempts. If the modems have become DOCSIS compliant, they will return online in the normal fashion. Refer to the SNMP Support for additional information about DMIC lock mode.

  • If a Broadband Access Center for Cable (BACC) provisioning server is being used, the Device Provisioning Engine (DPE) TFTP server verifies that the IP address of the TFTP client matches the expected DOCSIS cable modem IP Address. If a match is not found, the request is dropped. This functionality is incompatible with the CMTS DMIC feature. Use the no tftp verify-ip command on all BACC DPE servers to disable the verification of the requestor IP address on dynamic configuration TFTP requests. Refer to the Cisco Broadband Access Centre DPE CLI Reference in the http://www.cisco.com/c/en/us/td/docs/net_mgmt/broadband_access_center_for_cable/4-0/command/reference/DPECLIRef40.html for additional information.

Cable Modem Restrictions for Dynamic Shared Secret

DHCP Restriction for Incognito Server and Thomson Cable Modems

The Dynamic Host Configuration Protocol (DHCP) passes configuration information to DHCP hosts on a TCP/IP network. Configuration parameters and other control information are stored in the options field of the DHCP message.

When using DMIC with the Incognito DHCP server, the Incognito server must be re-configured so that the following two options are not sent in the DHCP message:

  • option 66 —This option is used to identify a TFTP server when the sname field in the DHCP header has been used for DHCP options. Option 66 is a variable-length field in the Options field of a DHCP message described as "an option used to identify a TFTP server when the 'sname' field in the DHCP header has been used for DHCP options" as per RFC 2132.
  • sname field —The sname field is a 64-octet field in the header of a DHCP message described as "optional server host name, null terminated string," as per RFC2131. A DHCP server inserts this option if the returned parameters exceed the usual space allotted for options. If this option is present, the client interprets the specified additional fields after it concludes interpretation of the standard option fields.

Note
It is not compliant with DOCSIS to include both of these options in the DHCP message.

The problematic packet capture below is a DHCP offer in which both sname and option 66 are set (in this respective sequence): 


0000  00 30 19 47 8f 00 00 d0 b7 aa 95 50 08 00 45 00
0010  01 4a 8f 50 00 00 80 11 46 30 ac 10 02 01 ac 10
0020  0a 01 00 43 00 43 01 36 0c 75 02 01 06 00 b0 a0
0030  25 01 00 00 00 00 00 00 00 00 ac 10 0a 53 00 00
0040  00 00 ac 10 0a 01 00 10 95 25 a0 b0 00 00 00 00
0050  00 00 00 00 00 00 5b 31 37 32 2e 31 36 2e 32 2e  
(sname option immediately above)
0060  31 5d 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0070  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0080  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0090  00 00 00 00 00 00 64 65 66 61 75 6c 74 2e 63 66
00a0  67 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00b0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00c0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00d0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00e0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00f0  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0100  00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0110  00 00 00 00 00 00 63 82 53 63 35 01 02 36 04 ac
0120  10 02 01 33 04 00 06 94 0d 01 04 ff ff ff 00 02
0130  04 ff ff b9 b0 03 08 ac 10 02 fe ac 10 0a 01 04
0140  04 ac 10 02 01 07 04 ac 10 02 01 42 0a 31 37 32 
(option 66 immediately above)
0150  2e 31 36 2e 32 2e 31 ff

When using DMIC with Incognito DHCP servers and Thomson cable modems, you must prevent both options from being sent in the DHCP offer. Use one of the following workaround methods to achieve this:

  • Change the Incognito DHCP server so that it does not include the sname option as described above.
  • Change the cable modem code so that sname is not prioritized above option 66, as in the problematic packet capture shown in the example above.
  • Migrate to a compliant DHCP and TFTP server such as CNR. This also offers significantly higher performance.

Refer to these resources for additional DOCSIS DHCP information, or optional DHCP MAC exclusion:

  • DHCP Options and BOOTP Vendor Extensions, RFC 2132

http://www.ietf.org/rfc/rfc2132.txt

  • Filtering Cable DHCP Lease Queries on Cisco CMTS Routers

http://www.cisco.com/en/US/docs/cable/cmts/feature/cblsrcvy.html

DOCSIS Compliance

  • Cable modems are assumed to be DOCSIS-compliant. If a cable modem is not fully DOCSIS-compliant, it could trigger a CMTS Message Integrity Check (MIC) failure during registration in rare circumstances. Under normal operations, however, it can be assumed that cable modems that fail the CMTS MIC check from the Dynamic Shared Secret feature are either not DOCSIS-compliant, or they might have been hacked by the end user to circumvent DOCSIS security features.

Some of the cable modems with the following OUIs have been identified as having problems with the Dynamic Shared Secret feature, depending on the hardware and software revisions:

    • 00.01.03
    • 00.E0.6F
    • 00.02.B2

These particular cable modems can remain stuck in the init(o) MAC state and cannot come online until the Dynamic Shared Secret feature is disabled. If this problem occurs, Cisco recommends upgrading the cable modem’s software to a fully compliant software revision.

Alternatively, these cable modems may be excluded from the dynamic secret function using the following command in global configuration mode:

cable dynamic-secret exclude

Excluding cable modems means that if a violator chooses to modify their cable modem to use one of the excluded OUIs, then the system is no longer protected. Refer to the .


Tip

To help providers to identify non-DOCSIS compliant modems in their network, the Dynamic Shared Secret feature supports a “mark-only” option. When operating in the mark-only mode, cable modems might be able to successfully obtain higher classes of service than are provisioned, but these cable modems will be marked as miscreant in the show cable modem displays (with !online , for example). Such cable modems also display with the show cable modem rogue command. Service providers may decide whether those cable modems must be upgraded to DOCSIS-compliant software, or whether the end users have hacked the cable modems for a theft-of-service attack.

The following example illustrates output from a Cisco CMTS that is configured with the cable dynamic-secret mark command with miscreant cable modems installed. These cable modems may briefly show up as "reject(m)" for up to three registration cycles before achieving the !online status. 


Router# show cable modem rogue
                                     Spoof TFTP
MAC Address    Vendor     Interface  Count Dnld Dynamic Secret
000f.0000.0133 00.0F.00   C4/0/U1    3     Yes  905B740F906B48870B3A9C5E441CDC67
000f.0000.0130 00.0F.00   C4/0/U1    3     Yes  051AEA93062A984F55B7AAC979D10901
000f.0000.0132 00.0F.00   C4/0/U2    3     Yes  FEDC1A6DA5C92B17B23AFD2BBFBAD9E1
vxr#scm | inc 000f
000f.0000.0133 4.174.4.101     C4/0/U1  !online       1     -7.00 2816    0   N
000f.0000.0130 4.174.4.89      C4/0/U1  !online       2     -6.50 2819    0   N
000f.0000.0132 4.174.4.90      C4/0/U2  !online       18    -7.00 2819    0   N

TFTP Restrictions

  • Cable modems can become stuck in the TFTP transfer state (this is indicated as init(o) by the show cable modem command) in the following situation:
    • The Dynamic Shared Secret feature is enabled on the cable interface, using the cable dynamic-secret command. This feature applies if the cable modem is a miscreant cable modem, or if the cable modem is a DOCSIS 1.0 cable modem running early DOCSIS 1.0 firmware that has not yet been updated. This feature also applies if the TFTP server is unable to provide the cable modem's TFTP configuration file to the Cisco CMTS. This is the case, for example, when using BACC and not configuring the system to permit a TFTP request from a non-matching source IP address. The debug cable dynamic-secret command also shows this failure.
    • A large number of cable modems are registering at the same time. Some or all of those cable modems could also be downloading the DOCSIS configuration file using multiple TFTP transfers that use multiple TFTP ports on the Cisco CMTS router, and the TFTP server is unable to keep up with the rate of TFTP requests generated by the system. Some TFTP servers may be limited to the number of concurrent TFTP get requests initiated by the same source IP address per unit time, or simply unable to handle the rate of new modem registrations before cable dynamic-secret is configured. The debug cable dynamic-secret command shows failure to receive some files in this situation.

This situation of stuck cable modems can result in the TFTP server running out of available ports, resulting in the cable modems failing the TFTP download stage. To prevent this situation from happening, temporarily disable the Dynamic Shared Secret feature on the cable interface or reduce the size of the DOCSIS configuration file.

Information About Dynamic Shared Secret

The DOCSIS specifications require that cable modems download, from an authorized TFTP server, a DOCSIS configuration file that specifies the quality of service (QoS) and other parameters for the network session. Theft-of-service attempts frequently attempt to intercept, modify, or substitute the authorized DOCSIS configuration file, or to download the file from a local TFTP server.

To prevent theft-of-service attempts, the DOCSIS specification allows service providers to use a shared secret password to calculate the CMTS Message Integrity Check (MIC) field that is attached to all DOCSIS configuration files. The CMTS MIC is an MD5 digest that is calculated over the DOCSIS Type/Length/Value (TLV) fields that are specified in the configuration file, and if a shared secret is being used, it is used in the MD5 calculation as well.

The cable modem must include its calculation of the CMTS MIC in its registration request, along with the contents of the DOCSIS configuration file. If a user modifies any of the fields in the DOCSIS configuration file, or uses a different shared secret value, the CMTS cannot verify the CMTS MIC when the cable modem registers. The CMTS does not allow the cable modem to register, and marks it as being in the “reject(m)” state to indicate a CMTS MIC failure.

Users, however, have used various techniques to circumvent these security checks, so that they can obtain configuration files that provide premium services, and then to use those files to provide themselves with higher classes of services. Service providers have responded by changing the shared secret, implementing DOCSIS time stamps, and using modem-specific configuration files, but this has meant creating DOCSIS configuration files for every cable modem on the network. Plus, these responses would have to be repeated whenever a shared secret has been discovered.

The Dynamic Shared Secret feature prevents these types of attacks by implementing a dynamically generated shared secret that is unique for each cable modem on the network. In addition, the dynamic shared secrets are valid only for the current session and cannot be reused, which removes the threat of “replay attacks,” as well as the reuse of modified and substituted DOCSIS configuration files.

Modes of Operation

The Dynamic Shared Secret feature can operate in three different modes, depending on what action should be taken for cable modems that fail the CMTS MIC verification check:

  • Marking Mode—When using the mark option, the CMTS allows cable modems to come online even if they fail the CMTS MIC validity check. However, the CMTS also prints a warning message on the console and marks the cable modem in the show cable modem command with an exclamation point (!), so that this situation can be investigated.
  • Locking Mode—When the lock option is used, the CMTS assigns a restrictive QoS configuration to CMs that fail the MIC validity check twice in a row. You can specify a particular QoS profile to be used for locked cable modems, or the CMTS defaults to special QoS profile that limits the downstream and upstream service flows to a maximum rate of 10 kbps.

If a customer resets their CM, the CM will reregister but still uses the restricted QoS profile. A locked CM continues with the restricted QoS profile until it goes offline and remains offline for at least 24 hours, at which point it is allowed to reregister with a valid DOCSIS configuration file. A system operator can manually clear the lock on a CM by using the clear cable modem lock command.

This option frustrates users who are repeatedly registering with the CMTS in an attempt to guess the shared secret, or to determine the details of the Dynamic Shared Secret security system.

  • Reject Mode—In the reject mode, the CMTS refuses to allow CMs to come online if they fail the CMTS MIC validity check. These cable modems are identified in the show cable modem displays with a MAC state of “reject(m)” (bad MIC value). After a short timeout period, the CM attempts to reregister with the CMTS. The CM must register with a valid DOCSIS configuration file before being allowed to come online. When it does come online, the CMTS also prints a warning message on the console and marks the cable modem in the show cable modem command with an exclamation point (!), so that this situation can be investigated.

Note
To account for possible network problems, such as loss of packets and congestion, the Cisco CMTS will allow a cable modem to attempt to register twice before marking it as having failed the Dynamic Shared Secret authentication checks.

Operation of the Dynamic Shared Secret

The Dynamic Shared Secret feature automatically creates a unique DOCSIS shared secret on a per-modem basis, creating a one-time use DOCSIS configuration file that is valid only for the current session. This ensures that a DOCSIS configuration file that has been downloaded for one cable modem can never be used by any other modem, nor can the same modem reuse this configuration file at a later time.

This patent pending feature is designed to guarantee that all registered modems are using only the QOS parameters that have been specified by the DOCSIS provisioning system for that particular modem at the time of its registration.

When a DOCSIS-compliant cable modem registers with the CMTS, it sends a DHCP request, and the DHCP server sends a DHCP response that contains the name of the DOCSIS configuration file that the cable modem should download from the specified TFTP server. The cable modem downloads the DOCSIS configuration file and uses its parameters to register with the CMTS

When the Dynamic Shared Secret feature is enabled, the CMTS performs the following when it receives the DHCP messages:

  • The CMTS creates a dynamically generated shared secret.
  • In the default configuration, the CMTS takes the name of the DOCSIS configuration file and generates a new, randomized filename. This randomized filename changes every time the cable modem registers, which prevents the caching of DOCSIS configuration files by cable modems that are only semi-compliant with the DOCSIS specifications. You can disable this randomization of the filename by using the nocrypt option with the cable dynamic-secret command.
  • The CMTS changes the IP address of the TFTP server that the cable modem should use to the IP address of the CMTS. This informs the cable modem that it should download its configuration file from the CMTS.
  • The CMTS downloads the original DOCSIS configuration file from the originally specified TFTP server so that it can modify the file to use the newly generated dynamic secret.

When the cable modem downloads the DOCSIS configuration file, it receives the modified file from the CMTS. Because this file uses the one-time-use dynamically generated shared secret, the CMTS can verify that the cable modem is using this configuration file when it attempts to register with the CMTS.


Note
The Dynamic Shared Secret feature does not support and is incompatible with, the use of the original shared secret or secondary shared secrets that are configured using the cable shared-secondary-secret and cable shared-secret commands.

Tip

Although a user could attempt to circumvent these checks by downloading a DOCSIS configuration file from a local TFTP server, the cable modem would still fail the CMTS MIC verification.

Interaction with Different Commands

The Dynamic Shared Secret feature works together with a number of other commands to ensure network security and integrity:

  • cable shared-secret —The DOCSIS specification allows service providers to use a shared-secret to ensure that cable modems are using only authorized DOCSIS configuration files.

    The Dynamic Shared Secret feature is incompatible with cable shared-secret . Do not configure the cable shared-secret command when using the Dynamic Shared Secret feature

  • cable shared-secondary-secret — The Dynamic Shared Secret feature is incompatible with cable shared-secret . Do not configure the cable secondary-shared-secret command when using the Dynamic Shared Secret feature

Performance Information

The Dynamic Shared Secret feature does not add any additional steps to the cable modem registration process, nor does it add any additional requirements to the current provisioning systems. This feature can have either a small negative or a small positive effect on the performance of the network provisioning system, depending on the following factors:

  • The provisioning system (DHCP and TFTP servers) being used
  • The number of cable modems that are coming online
  • The vendor and software versions of the cable modems
  • The number and size of the DOCSIS configuration files

Large-scale testing has shown that the Dynamic Shared Secret feature can affect the time it takes for cable modems to come online from 5% slower to 10% faster. The most significant factor in the performance of the provisioning process is the provisioning system itself. For this reason, Cisco recommends using Cisco Network Registrar (CNR) Release 3.5 or greater, which can provide significant performance improvements over generic DHCP and TFTP servers.

The second-most important factor in the performance of cable modem provisioning is the number and size of the DOCSIS configuration files. The size of the configuration file determines how long it takes to transmit the file to the cable modem, while the number of configuration files can impact how efficiently the system keeps the files in its internal cache, allowing it to reuse identical configuration files for multiple modems.

SNMP Support

Cisco IOS-XE 3.15.0S and later releases add the following SNMP support for the Dynamic Shared Secret feature:

  • Adds the following MIB objects to the CISCO-DOCS-EXT-MIB:
    • cdxCmtsCmDMICMode—Sets and shows the configuration of the Dynamic Shared Secret feature for a specific cable modem (not configured, mark, lock, or reject).
    • cdxCmtsCmDMICLockQoS—Specifies the restrictive QoS profile assigned to a cable modem that has failed the Dynamic Shared Secret security checks, when the interface has been configured for lock mode.
    • cdxCmtsCmStatusDMICTable—Lists all cable modems that have failed the Dynamic Shared Secret security checks.
  • An SNMP trap (cdxCmtsCmDMICLockNotification) can be sent when a cable modem is locked for failing the Dynamic Shared Secret security checks. The trap can be enabled using the snmp-server enable traps cable dmic-lock command.

Note
The DMIC lock mode is disabled during a switchover event in HCCP N+1 Redundancy.

System Error Messages

The following system error messages provide information about cable modems that have failed the CMTS Message Integrity Check (MIC) when the Dynamic Shared Secret feature is enabled.

Message 

 %CBR-4-CMLOCKED

The cable modem’s DOCSIS configuration file did not contain a Message Integrity Check (MIC) value that corresponds with the proper Dynamic Shared Secret that was used to encode it. The CMTS has, therefore, assigned a restrictive quality of service (QoS) configuration to this cable modem to limit its access to the network. The CMTS has also locked the cable modem so that it will remain locked in the restricted QoS configuration until it goes offline for at least 24 hours, at which point it is permitted to reregister and obtain normal service (assuming it is DOCSIS-compliant and using a valid DOCSIS configuration file).

This error message appears when the cable dynamic-secret lock command has been applied to a cable interface to enable the Dynamic Shared Secret feature for the DOCSIS configuration files on that cable interface. The cable modem has been allowed to register and come online, but with a QoS configuration that is limited to a maximum rate of 10 kbps for both the upstream and downstream flows. Check to ensure that this cable modem is not running old software that caches the previously used configuration file. Also check for a possible theft-of-service attempt by a user attempting to download a modified DOCSIS configuration file from a local TFTP server. The CM cannot reregister with a different QoS profile until it has been offline for 24 hours, without attempting to register, or you have manually cleared the lock using the clear cable modem lock command.

Message 

 %CBR-4-CMMARKED

The cable modem’s DOCSIS configuration file did not contain a Message Integrity Check (MIC) value that corresponds with the proper dynamic shared secret that was used to encode it. The CMTS has allowed this modem to register and come online, but has marked it in the show cable modem displays with an exclamation point (!) so that the situation can be investigated.

This error message appears when the cable dynamic-secret mark command has been applied to a cable interface to enable the Dynamic Shared Secret feature for the DOCSIS configuration files on that cable interface. Check to ensure that this cable modem is not running old software that caches the previously used configuration file. Also check for a possible theft-of-service attempt by a user attempting to download a modified DOCSIS configuration file from a local TFTP server.

Message 

 %CBR-4-NOCFGFILE

The CMTS could not obtain the DOCSIS configuration file for this cable modem from the TFTP server. This message occurs when the Dynamic Shared Secret feature is enabled on the cable interface with the cable dynamic-secret command.

Verify that the CMTS has network connectivity with the TFTP server, and that the specified DOCSIS configuration file is available on the TFTP server. Check that the DHCP server is correctly configured to send the proper configuration filename in its DHCP response to the cable modem. Also verify that the DOCSIS configuration file is correctly formatted.

This problem could also occur if the TFTP server is offline or is overloaded to the point where it cannot respond promptly to new requests. It might also be seen if the interface between the CMTS and TFTP server is not correctly configured and flaps excessively.


Note
This error indicates a problem with the provisioning system outside of the Cisco CMTS. Disabling the Dynamic Shared Secret feature does not clear the fault, nor does it allow cable modems to come online. You must first correct the problem with the provisioning system.

Benefits

The Dynamic Shared Secret feature provides the following benefits to cable service providers and their partners and customers:

Improves Network Security

Service providers do not need to worry about users discovering the shared secret value and using it to modify DOCSIS configuration files to give themselves higher levels of service. Even if a user were to discover the value of a dynamically generated shared secret, the user would not be able to use that shared secret again to register.

The generic TFTP server performance and error handling on the Cisco CMTS routers has been greatly improved to support the high performance that is required for rapidly provisioning cable modems.

Flexibility in Dealing with Possible Theft-of-Service Attempts

Service providers have the option of deciding what response to take when a DOCSIS configuration file fails its CMTS MIC check: mark that cable modem and allow the user online, reject the registration request and refuse to allow the user to come online until a valid DOCSIS configuration file is used, or lock the cable modem in a restricted QoS configuration until the modem remains offline for 24 hours. Locking malicious modems is the most effective deterrent against hackers, because it provides the maximum penalty and minimum reward for any user attempting a theft-of-service attack.

No Changes to Provisioning System Are Needed

Service providers can use the Dynamic Shared Secret feature without changing their provisioning or authentication systems. Existing DOCSIS configuration files can be used unchanged, and you do not need to change any existing shared secrets.


Tip

If not already done, the service provider could also install access controls that allow only the CMTS routers to download DOCSIS configuration files from the TFTP servers.

No Changes to Cable Modems Are Needed

The Dynamic Shared Secret feature does not require any end-user changes or any changes to the cable modem configuration. This feature supports any DOCSIS compliant cable modem.


Note
The Dynamic Shared Secret feature does not affect cable modems that are already online and provisioned. Cable modems that are already online when the feature is enabled or disabled remain online.

Simplifies Network Management

Service providers do not have to continually update the shared secrets on a cable interface whenever the files providing premium services become widely available. Instead, providers can use the same shared secret on a cable interface for significant periods of time, trusting in the Dynamic Shared Secret feature to provide unique, single-use shared secrets for each cable modem.

In addition, service providers do not have to manage unique DOCSIS configuration files for each cable modem. The same configuration file can be used for all users in the same service class, without affecting network security.

Related Features

The following features can be used with the Dynamic Shared Secret feature to enhance the overall security of the cable network.

  • Baseline Privacy Interface Plus (BPI+) Authorization and Encryption—Provides a secure link between the cable modem and CMTS, preventing users from intercepting or modifying packets that are transmitted over the cable interface. BPI+ also provides for secure authorization of cable modems, using X.509 digital certificates, as well as a secure software download capability that ensures that software upgrades are not spoofed, intercepted, or altered.

How to Configure the Dynamic Shared Secret Feature

The following sections describe how to enable and configure the Dynamic Shared Secret feature, to disable the feature, to manually clear a lock on a cable modem, or dynamically upgrade firmware on the cable modems.


Note
All procedures begin and end at the privileged EXEC prompt (“Router#”).

Enabling and Configuring the Dynamic Shared Secret Feature

This section describes how to enable and configure the Dynamic Shared Secret feature on a cable interface.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Router# configure terminal

Example:


Router(config)#

Enters global configuration mode.

Step 2

cable qos permission create

Example:


Router(config)# cable qos permission create

Example:


Router(config)#

(Optional) If you are using the lock option in Step 6, and if you are not specifying a specific QoS profile to be used, you must allow cable modems to create their own QoS profiles.

Step 3

cable qos permission update

Example:


Router(config)# cable qos permission update

Example:


Router(config)#

(Optional) If you are using the lock option in Step 6, and if you are not specifying a specific QoS profile to be used, you must allow cable modems to update their own QoS profiles.

Step 4

snmp-server enable traps cable dmic-lock

Example:


Router(config)# snmp-server enable traps cable dmic-lock

Example:


Router(config)#

(Optional) Enables the sending of SNMP traps when a cable modem fails a dynamic shared-secret security check.

Step 5

interface cable interface

Example:


Router(config)# interface cable 3/0

Example:


Router(config-if)#

Enters interface configuration mode for the specified cable interface.

Step 6

cable dynamic-secret {lock [lock-qos ] | mark | reject } [nocrypt

Example:


Router(config-if)# cable dynamic-secret lock

Example:


Router(config-if)# cable dynamic-secret lock 90

Example:


Router(config-if)# cable dynamic-secret mark

Example:


Router(config-if)# cable dynamic-secret reject

Example:


Router(config-if)#

Enables the Dynamic Shared Secret feature on the cable interface and configures it for the appropriate option:

  • nocrypt —(Optional) The Cisco CMTS does not encrypt the filenames of DOCSIS configuration files, but sends the files to CMs using their original names.
  • lock —Cable modems that fail the MIC verification are allowed online with a restrictive QoS profile. The cable modems must remain offline for 24 hours to be able to reregister with a different QoS profile.
  • lock-qos —(Optional) Specifies the QoS profile that should be assigned to locked cable modems. The valid range is 1 to 256, and the profile must have already been created. If not specified, locked cable modems are assigned a QoS profile that limits service flows to 10 kbps (requires Step 2 and Step 3).
  • mark —Cable modems that fail the MIC verification are allowed online but are marked in the show cable modem displays so that the situation can be investigated.
  • reject —Cable modems that fail the MIC verification are not allowed to register.
Note 
Repeat Step 5 and Step 6 for each cable interface to be configured.
Step 7

end

Example:


Router(config-if)# end

Example:


Router#

Exits interface configuration mode and returns to privileged EXEC mode.

What to do next


Note
If you configure the Dynamic Shared Secret feature on any interface in a cable interface bundle, you should configure it on all interfaces in that same bundle.

Disabling the Dynamic Shared Secret on a Cable Interface

This section describes how to disable the Dynamic Shared Secret feature on a cable interface. The cable modem continues to be validated against any shared secret or secondary shared secrets that have been defined on the cable interface.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Router# configure terminal

Example:


Router(config)#

Enters global configuration mode.

Step 2

interface cable interface

Example:


Router(config)# interface cable 3/0

Example:


Router(config-if)#

Enters interface configuration mode for the specified cable interface.

Step 3

no cable dynamic-secret

Example:


Router(config-if)# no cable dynamic-secret

Example:


Router(config-if)#

Disables the Dynamic Shared Secret feature on the cable interface.

Note 
Repeat Step 2 and Step 3 for each cable interface to be configured.
Step 4

end

Example:


Router(config-if)# end

Example:


Router#

Exits interface configuration mode and returns to privileged EXEC mode.

Excluding Cable Modems from the Dynamic Shared Secret Feature

This section describes how to exclude one or more cable modems from being processed by the Dynamic Shared Secret feature. The cable modem continues to be validated against any shared secret or secondary shared secrets that have been defined on the cable interface.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 2

cable dynamic-secret exclude {oui oui-id | modem mac-address}

Example:


Router(config)# cable dynamic-secret exclude oui 00.01.B4 
Router(config)# cable dynamic-secret exclude modem 00d0.45ba.b34b

Excludes one or more cable modems from being processed by the Dynamic Shared Secret security checks, on the basis of their MAC addresses or OUI values:

  • modem mac-address —Specifies the hardware (MAC) address of one specific and individual cable modem to be excluded from the Dynamic Shared Secret feature. (You cannot specify a multicast MAC address.)

  • oui oui-id —Specifies the organization unique identifier (OUI) of a vendor, so that a group of cable modems from this vendor are excluded from the Dynamic Shared Secret feature. The OUI should be specified as three hexadecimal bytes separated by either periods or colons.

Note 

Repeat this command for each cable modem MAC address or OUI vendor to be excluded.

Step 3

exit

Example:

Router(config)# exit
Exits the interface configuration mode and returns to privileged EXEC mode.

Clearing the Lock on One or More Cable Modems

This section describes how to manually clear the lock on one or more cable modems. This forces the cable modems to reinitialize, and the cable modems must reregister with a valid DOCSIS configuration file before being allowed online. If you do not manually clear the lock (using the clear cable modem lock command), the cable modem is locked in its current restricted QoS profile and cannot reregister with a different profile until it has been offline for at least 24 hours.

Procedure

Command or Action Purpose

clear cable modem {mac-addr | ip-addr | all | oui string | reject } lock

Example:


Router# clear cable modem 0001.0203.0405 lock

Example:


Router# clear cable modem all lock

Example:


Router# clear cable modem oui 00.00.0C lock

Example:


Router#

Clears the lock for the cable modems, which can be identified as follows:

  • mac-addr —Specifies the MAC address for one particular cable modem to be cleared.
  • ip-addr —Specifies the IP address for one particular cable modem to be cleared.
  • all —Clears the locks on all locked cable modems.
  • oui string —Clears the locks on all cable modems with a vendor ID that matches the specified Organizational Unique Identifier (OUI) string.
  • reject —Clears the locks on all cable modems that are currently in the reject state (which would occur if a locked cable modem went offline and attempted to reregister before 24 hours had elapsed).

What to do next


Tip

A cable modem can also be unlocked by manually deleting the cable modem from all CMTS internal databases, using the clear cable modem delete command.

Upgrading Firmware on the Cable Modems

This section describes how to upgrade firmware on cable modems by dynamically inserting the correct TLV values in the DOCSIS configuration file that is downloaded by the cable modem. The DOCSIS configuration file contains the following TLV values:

  • Software Upgrade Filename (TLV 9)—Specifies the filename of the firmware.
  • Upgrade IPv4 TFTP Server (TLV21)—Specifies the IPv4 address of the TFTP server from where the modem downloads the DOCSIS configuration file.
  • Upgrade IPv6 TFTP Server (TLV58)—Specifies the IPv6 address of the TFTP server from where the modem downloads the DOCSIS configuration file.

Note
The TFTP server addresses are inserted only when the software upgrade filename (TLV9) is specified and when the TFTP server address (TLV21/TLV58) is either not specified or set to 0.

Before you begin

The Dynamic Shared Secret feature must be enabled first before you can upgrade the firmware on cable modems. See Enabling and Configuring the Dynamic Shared Secret Feature for more information.


Note
The command to enable or disable the Dynamic Shared Secret feature is available at the MAC domain level. However, the command to upgrade the firmware on cable modems is available at the global level.

Procedure

  Command or Action Purpose
Step 1

configure terminal

Example:


Router# configure terminal

Example:


Router(config)#

Enters the global configuration mode.

Step 2

cable dynamic-secret tftp insert-upgrade-server

Example:


Router(config)# cable dynamic-secret tftp insert-upgrade-server

Dynamically inserts the specific IPv4 or IPv6 TLV values in the DOCSIS configuration file to complete firmware upgrade on cable modems.

Step 3

end

Example:


Router(config)# end

Example:


Router#

Exits the configuration mode and returns to the privileged EXEC mode.

What to do next


Note
If you configure the Dynamic Shared Secret feature on an interface in a cable interface bundle, you should configure it on all the interfaces of that bundle.

How to Monitor the Dynamic Shared Secret Feature

This section describes the following procedures you can use to monitor and display information about the Dynamic Shared Secret feature:

Displaying Marked Cable Modems

When you configure a cable interface with the cable dynamic-secret mark command, cable modems that fail the dynamically generated CMTS MIC verification are allowed online, but are marked with an exclamation point (!) in the MAC state column in the show cable modem display. The exclamation point is also used to identify cable modems that were initially rejected, using the cable dynamic-secret reject command, but then reregistered using a valid DOCSIS configuration file.

For example, the following example shows that four cable modems are marked as having failed the CMTS MIC verification, but that they have been allowed online: 


Router# show cable modems
 
MAC Address    IP Address      I/F       MAC         Prim RxPwr  Timing  Num BPI
                                         State       Sid  (db)   Offset  CPE Enb
0010.9507.01db 144.205.151.130 C5/1/0/U5 online(pt)  1     0.25    938   1    N 
0080.37b8.e99b 144.205.151.131 C5/1/0/U5 online      2     -0.25   1268  0    N 
0002.fdfa.12ef 144.205.151.232 C6/1/0/U0 online(pt)  13    -0.25   1920  1    N 
0002.fdfa.137d 144.205.151.160 C6/1/0/U0 !online     16    -0.50   1920  1    N 
0003.e38f.e9ab 144.205.151.237 C6/1/0/U0 !online     3     -0.50   1926  1    N 
0003.e3a6.8173 144.205.151.179 C6/1/1/U2 offline     4     0.50    1929  0    N 
0003.e3a6.8195 144.205.151.219 C6/1/1/U2 !online(pt) 22    -0.50   1929  1    N 
0006.28dc.37fd 144.205.151.244 C6/1/1/U2 online(pt)  61    0.00    1925  2    N 
0006.28e9.81c9 144.205.151.138 C6/1/1/U2 online(pt)  2     0.75    1925  1    N 
0006.28f9.8bbd 144.205.151.134 C6/1/1/U2 online      25    -0.25   1924  1    N 
0006.28f9.9d19 144.205.151.144 C6/1/1/U2 online(pt)  28    0.25    1924  1    N 
0010.7bed.9b6d 144.205.151.228 C6/1/1/U2 online(pt)  59    0.25    1554  1    N 
0002.fdfa.12db 144.205.151.234 C7/0/0/U0 online      15    -0.75   1914  1    N 
0002.fdfa.138d 144.205.151.140 C7/0/0/U5 online      4     0.00    1917  1    N 
0003.e38f.e85b 144.205.151.214 C7/0/0/U5 !online     17    0.25    1919  1    N 
0003.e38f.f4cb 144.205.151.238 C7/0/0/U5 online(pt)  16    0.00   !2750  1    N 
0003.e3a6.7fd9 144.205.151.151 C7/0/0/U5 online      1     0.25    1922  0    N 
0020.4005.3f06 144.205.151.145 C7/0/0/U0 online(pt)  2     0.00    1901  1    N 
0020.4006.b010 144.205.151.164 C7/0/0/U5 online(pt)  3     0.00    1901  1    N 
0050.7302.3d83 144.205.151.240 C7/0/0/U0 online(pt)  18    -0.25   1543  1    N 
00b0.6478.ae8d 144.205.151.254 C7/0/0/U5 online(pt)  44    0.25    1920  21   N 
00d0.bad3.c0cd 144.205.151.149 C7/0/0/U5 online      19    0.25    1543  1    N 
00d0.bad3.c0cf 144.205.151.194 C7/0/0/U0 online      13    0.00    1546  1    N 
00d0.bad3.c0d5 144.205.151.133 C7/0/0/U0 online      12    0.50    1546  1    N 
Router#

You can also use the show cable modem rogue command to display only those cable modems that have been rejected for failing the dynamic shared-secret authentication checks: 


Router# show cable modem rogue 
                                     Spoof TFTP
MAC Address    Vendor     Interface  Count Dnld Dynamic Secret
AAAA.7b43.aa7f Vendor1    C4/0/U5       2  Yes  45494DC933F8F47A398F69EE6361B017 
AAAA.7b43.aa7f Vendor1    C4/0/U5       2  Yes  D47BCBB5494E9936D51CB0EB66EF0B0A 
BBBB.7b43.aa7f Vendor2    C4/0/U5       2  No   8EB196423170B26684BF6730C099D271 
AAAA.7b43.aa7f Vendor1    C4/0/U5       2  No   DF8FE30203010001A326302430120603 
BBBB.7b43.aa7f Vendor2    C4/0/U5       2  No   300E0603551D0F0101FF040403020106 
AAAA.7b43.aa7f Vendor1    C4/0/U5       2  Yes  820101002D1A264CE212A1BB6C1728B3 
DDDD.7b43.aa7f Vendor4    C4/0/U5       2  Yes  7935B694DCA90BC624AC92A519C214B9 
AAAA.7b43.aa7f Vendor1    C4/0/U5       2  No   3AB096D00D56ECD07D9B7AB662451CFF 
Router#

Displaying the Current Dynamic Secrets

In Cisco IOS-XE Release 3.15.0S, the verbose option for the show cable modem command displays the dynamically generated shared secret (a 16-byte hexadecimal value) that was used in the cable modem’s previous registration cycle. The display also shows if the cable modem failed the dynamic shared-secret check or did not download the DOCSIS configuration file from the TFTP server. If a cable modem is offline, its dynamic secret is shown as all zeros.

For example, the following example shows a typical display for a single cable modem that failed the dynamic shared-secret check: 


Router# show cable modem 00c0.73ee.bbaa verbose
 
MAC Address                         : 00c0.73ee.bbaa 
IP Address                          : 3.18.1.6
Prim Sid                            : 2
QoS Profile Index                   : 6
Interface                           : C3/0/U0
Upstream Power                      : 0.00 dBmV (SNR = 26.92 dBmV)
Downstream Power                    : 0.00 dBmV (SNR = ----- dBmV)
Timing Offset                       :  2812  
Initial Timing Offset               : 2812
Received Power                      :  0.00
MAC Version                         : DOC1.0
Provisioned Mode                    : DOC1.0
Capabilities                        : {Frag=N, Concat=N, PHS=N, Priv=BPI}
Sid/Said Limit                      : {Max Us Sids=0, Max Ds Saids=0}
Optional Filtering Support          : {802.1P=N, 802.1Q=N}
Transmit Equalizer Support          : {Taps/Symbol= 0, Num of Taps= 0}
Number of CPE IPs                   : 0(Max CPE IPs = 1)
CFG Max-CPE                         : 1
Flaps                               : 26(Feb 14 02:35:39)
Errors                              : 0 CRCs, 0 HCSes
Stn Mtn Failures                    : 6 aborts, 0 exhausted
Total US Flows                      : 1(1 active)
Total DS Flows                      : 1(1 active)
Total US Data                       : 0 packets, 0 bytes
Total US Throughput                 : 0 bits/sec, 0 packets/sec
Total DS Data                       : 0 packets, 0 bytes
Total DS Throughput                 : 0 bits/sec, 0 packets/sec
Active Classifiers                  : 0 (Max = NO LIMIT) 
Dynamic Secret                      : A3D1028F36EBD54FDCC2F74719664D3F
Router#

The following example shows a typical display for a single cable modem that is currently offline (the Dynamic Secret field shows all zeros): 


Router# show cable modem 00C0.6914.8601 verbose
 
MAC Address                         : 00C0.6914.8601
IP Address                          : 10.212.192.119
Prim Sid                            : 6231
QoS Profile Index                   : 2
Interface                           : C5/1/0/U3
Upstream Power                      : 0.00 dBmV (SNR = 30.19 dBmV)
Downstream Power                    : 0.00 dBmV (SNR = ----- dBmV)
Timing Offset                       : 1831
Initial Timing Offset               : 1831
Received Power                      : !-2.25
MAC Version                         : DOC1.0
Provisioned Mode                    : DOC1.0
Capabilities                        : {Frag=N, Concat=Y, PHS=N, Priv=BPI}
Sid/Said Limit                      : {Max Us Sids=0, Max Ds Saids=0}
Optional Filtering Support          : {802.1P=N, 802.1Q=N}
Transmit Equalizer Support          : {Taps/Symbol= 0, Num of Taps= 0}
Number of CPE IPs                   : 4(Max CPE IPs = 4)
CFG Max-CPE                         : 4
Flaps                               : 20638(Feb 10 16:04:10)
Errors                              : 0 CRCs, 0 HCSes
Stn Mtn Failures                    : 108 aborts, 161 exhausted
Total US Flows                      : 1(1 active)
Total DS Flows                      : 1(1 active)
Total US Data                       : 236222 packets, 146630868 bytes
Total US Throughput                 : 0 bits/sec, 0 packets/sec
Total DS Data                       : 9 packets, 1114 bytes
Total DS Throughput                 : 0 bits/sec, 0 packets/sec
Active Classifiers                  : 0 (Max = NO LIMIT)
Dynamic Secret                      : 00000000000000000000000000000000
Router#

Note
The Dynamic Secret field shown above is all zeros (“00000000000000000000000000000000”), which indicates that this cable modem is offline.

You can also use the following command to display all the dynamically generated shared secrets that are in use: 


Router# show cable modem verbose | include Dynamic Secret
 
Dynamic Secret                      : 43433036434644344643303841313237
Dynamic Secret                      : 308203E0308202C8A003020102021058
Dynamic Secret                      : 0D06092A864886F70D01010505003081 
Dynamic Secret                      : 3037060355040A133044617461204F76 
Dynamic Secret                      : 20496E74657266616365205370656369 
Dynamic Secret                      : 00000000000000000000000000000000
Dynamic Secret                      : 040B130C4361626C65204D6F64656D73 
Dynamic Secret                      : 53204361626C65204D6F64656D20526F 
Dynamic Secret                      : 7574686F72697479301E170D30313032 
Dynamic Secret                      : 313233353935395A308197310B300906 
Dynamic Secret                      : 0A133044617461204F76657220436162 
Dynamic Secret                      : 66616365205370656369666963617469 
Dynamic Secret                      : 626C65204D6F64656D73313630340603 
Dynamic Secret                      : 65204D6F64656D20526F6F7420436572 
Dynamic Secret                      : 747930820122300D06092A864886F70D 
Dynamic Secret                      : 010100C0EF369D7BDAB0A938E6ED29C3 
Dynamic Secret                      : DA398BF619A11B3C0F64912D133CFFB6 
Dynamic Secret                      : FFAD6CE01590ABF5A1A0F50AC05221F2 
Dynamic Secret                      : 73504BCA8278D41CAD50D9849B56552D 
Dynamic Secret                      : 05F4655F2981E031EB76C90F9B3100D1 
Dynamic Secret                      : F4CB0BF4A13EA9512FDE4A2A219C27E9 
Dynamic Secret                      : D47BCBB5494E9936D51CB0EB66EF0B0A 
Dynamic Secret                      : 8EB196423170B26684BF6730C099D271 
Dynamic Secret                      : DF8FE30203010001A326302430120603 
Dynamic Secret                      : 300E0603551D0F0101FF040403020106 
Dynamic Secret                      : 820101002D1A264CE212A1BB6C1728B3 
Dynamic Secret                      : 7935B694DCA90BC624AC92A519C214B9 
Dynamic Secret                      : 3AB096D00D56ECD07D9B7AB662451CFF 
Dynamic Secret                      : 92E68CFD8783D58557E3994F23A8140F 
Dynamic Secret                      : 225A3B01DB67AF0C3637A765E1E7C329 
Dynamic Secret                      : 2BB1E6221B6D5596F3D6F506804C995E 
Dynamic Secret                      : 45494DC933F8F47A398F69EE6361B017 
Router#

Troubleshooting Cable Modems with Dynamic Shared Secret

If a cable modem is being marked as having violated the dynamic shared secret, you can enable the following debugs to get more information about the sequence of events that is occurring:

  • debug cable mac-address cm-mac-addr verbose —Enables detailed debugging for the cable modem with the specific MAC address.
  • debug cable tlv —Displays the contents of Type/Length/Value messages that are sent during the registration process.
  • debug cable dynamic-secret —Displays debugging messages about dynamic shared secret operation.
  • debug tftp server events —Displays debugging messages for the major events that occur with the Cisco CMTS router’s onboard TFTP server.
  • debug tftp server packets —Displays a packet dump for the DOCSIS configuration files that the TFTP server downloads to a cable modem.

Tip

For more information about these debug commands, see the Cisco CMTS Debugging Commands chapter in the Cisco Broadband Cable Command Reference Guide, at the following URL: http://www.cisco.com/en/US/docs/ios/cable/command/reference/cbl_book.html

In addition, examine the messages in the router’s log buffer for any helpful information. Use the show logging command to display the contents of the router’s logging buffer to display these messages. You can limit the output to a specific hour and minute by using the begin output modifier. For example, to display only those messages that were recorded at 12:10, give the following command: 


Router# show logging | begin 12:10

Note
The exact format for the begin output modifier depends on the timestamp you are using for your logging buffer.

Configuration Examples for Dynamic Shared Secret

This section lists a typical configuration for the Dynamic Shared Secret feature.


Note
These configurations also show a shared secret and secondary secret being configured on the cable interface. This is optional but highly recommended, because it adds an additional layer of security during the registration of cable modems.

Mark Configuration: Example

The following excerpt from a configuration for the cable interface on a Cisco CMTS router configures the cable interface so that cable modems that fail the CMTS MIC check are allowed to come online, but are marked with an exclamation point (!) in the show cable modem displays, so that the situation can be investigated further. 


interface cable c5/1/0 
 cable dynamic-secret mark 
 ...

Lock Configuration: Example

The following excerpt from a configuration for the cable interface on a Cisco CMTS router configures the cable interface so that cable modems that fail the CMTS MIC check are allowed to come online, but are locked into a restrictive QoS configuration that limits the upstream and downstream service flows to a maximum rate of 10 kbps. A locked cable modem remains locked into the restrictive QoS configuration until the modem has remained offline for more than 24 hours, or until you have manually cleared it using the clear cable modem lock command. 


cable qos permission create 
cable qos permission update 
...
interface cable c3/0 
 cable dynamic-secret lock 
 ...

Note
If you use the lock option without specifying a specific QoS profile, you must allow cable modems to create and update QoS profiles, using the cable qos permission command. If you do not do this and continue to use the lock option without specifying a particular QoS profile, locked cable modems will not be allowed to register until the lock clears or expires.

The following example is the same except that it specifies that the locked cable modem should be assigned QoS profile 90. The cable modem remains locked with this QoS profile until the modem has remained offline for more than 24 hours, or until you have manually cleared it using the clear cable modem lock command. Because a specific QoS profile is specified, you do not need to use the cable qos permission command. 


interface cable c3/0 
 cable dynamic-secret lock 90 
 ...

Note
When a locked modem is cleared, it is automatically reset so that it reregisters with the CMTS. It is allowed online with the requested QoS parameters if it registers with a valid DOCSIS configuration that passes the Dynamic Shared Secret checks. However, the modem is locked again if it violates the DOCSIS specifications again.

Reject Configuration: Example

The following excerpt from a configuration for the cable interface on a Cisco CMTS configures the cable interface so that cable modems that fail the CMTS MIC check are rejected and not allowed to register. The cable modem must reregister using a DOCSIS configuration file with a CMTS MIC that matches one of the shared secret or secondary secret values. When it does come online, the CMTS also prints a warning message on the console and marks the cable modem in the show cable modem command with an exclamation point (!), so that this situation can be investigated. 


interface cable c3/0 
 cable dynamic-secret reject 
 ...

Disabled Configuration: Example

The following excerpt from a configuration for the cable interface on a Cisco uBR7100 series router disables the Dynamic Shared Secret feature. In this configuration, the CMTS uses the shared secret and secondary shared secret values unchanged when verifying the CMTS MIC value for each DOCSIS configuration file. 


interface cable c1/0 
 no cable dynamic-secret 
 ...

Additional References

For additional information related to Dynamic Shared Secret, refer to the following references:

Standards

Standards2

Title

SP-RFIv1.1-I09-020830

Data-over-Cable Service Interface Specifications Radio Frequency Interface Specification, version 1.1

2 Not all supported standards are listed.

MIBs

MIBs3

MIBs Link

No new or modified MIB objects are supported by the Dynamic Shared Secret feature.

  • CISCO-DOCS-EXT-MIB—Includes attributes to configure the Dynamic Shared Secret feature and to generate traps when a cable modem fails the shared-secret security checks.

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

3 Not all supported MIBs are listed.

RFCs

RFCs4

Title

RFC 2233

DOCSIS OSSI Objects Support

RFC 2665

DOCSIS Ethernet MIB Objects Support

RFC 2669

Cable Device MIB

4 Not all supported RFCs are listed.

Feature Information for Dynamic Shared Secret

Use Cisco Feature Navigator to find information about platform support and software image support. Cisco Feature Navigator enables you to determine which software images support a specific software release, feature set, or platform. To access Cisco Feature Navigator, go to http://tools.cisco.com/ITDIT/CFN/. An account on http://www.cisco.com/ is not required.


Note

The below table lists only the software release that introduced support for a given feature in a given software release train. Unless noted otherwise, subsequent releases of that software release train also support that feature.

Table 2. Feature Information for Downstream Interface Configuration

Feature Name

Releases

Feature Information

Dynamic Shared Secret

Cisco IOS-XE 3.15.0S

This feature was introduced on the Cisco cBR Series Converged Broadband Router .

Was this Document Helpful?

FeedbackFeedback

Contact Cisco