Contents

Introduction

Prerequisite

Requirement

Components Used

Background Information

Logs to be Collected on Any WLC Issue

Advanced Information on AP/Client Debugs from 9800 WLC

Always-on-tracing

RadioActive Tracing

Embedded Packet Capture

Packet Capture filtered on AP IP

Packet Capture filtered on Client MAC(available after Cisco IOS® XE 17.1.1s)

Verify

Scenario Specific Log Collection:

WLC Platform Issues

AP Join/Connectivity Issues

Client Connectivity Issues

Guest Central Web Authentication (CWA) or Local Web Authentication (LWA) Issues

Radio Frequency (RF) or Radio Resource Management(RRM) Issues

License Issues

High Availability issues

Web User Interface or GUI Issues

Related Information

Introduction

This document describes steps to collect important debugs or show commands from Catalyst 9800 Wireless LAN Controllers (WLC).

Prerequisite

Requirement

Cisco recommends that you have knowledge of this topic:

- Basic understanding of Catalyst 9800 Wireless LAN Controllers(WLC)

Components Used

The information in this document is based on these software and hardware versions:

- Catalyst 9800 WLC

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Background Information

This document describes steps to collect important debugs or show commands from Catalyst 9800 Wireless LAN Controllers(WLC).

Logs to be Collected on Any WLC Issue

- Document exact and detailed problem description:

Provide information about the WLC platform, version of code, number of APs/clients impacted, SSIDs where the issue is seen, issues observed.

Ex: 9800-40 in HA with software version 16.12.3 guest clients not able to connect to SSID ACME_CORP_GUEST, 500 APs, and 200 clients impacted.

- AP details/Client details: Make, MAC Address, Model, OS version, WLAN Adapter Version.

Provide one concrete example of client/AP when it does not work with the MAC address of the AP/Client, model, software version, and WLAN adapter driver version. Ensure that this is AP/Client used to collect outputs and debugs.

Ex: Issue is seen in AP AP02_ACME 9120AXI where client fails to connect Intel AX200 client MAC@ aaaa.bbbb.cccc with driver version 10.21.0.5

- Timestamps of the issue. Frequency of the issue:

When did the issue start? How often does the issue occur? Is the issue consistently observed?

Provide concrete timestamps of the issue seen when you collect data.

Ex: The issue is consistently seen every time client tries to connect. The issue started to occur on 16/0/4/2020 after upgrade to 16.12.3

- Working vs non-working/changes / Trigger:

Was this working fine before? If it was working fine what changes occurred that could trigger the issue? Is it reproducible? What are the steps done to reproduce it? Provide details about what is working and what is not working.

Ex: It was working fine in 16.12.2s, the issue started to occur in 16.12.3. The issue is consistently reproducible when you connect any client to ACME_CORP_GUEST. Other SSIDs are working fine, the same client is able to connect to other SSID in the same AP.

- From Catalyst 9800 CLI, collect output of:

WLC-9800-CLI# show tech wireless

Alternatively, you can collect the same output via GUI. Navigate to Troubleshooting>Debug Bundle menu:

Advanced Information on AP/Client Debugs from 9800 WLC

Some of the debugging functionalities available in Catalyst 9800 WLC are summarized here. Refer to Understand Wireless Debugs and Log Collection on Catalyst 9800 Wireless LAN Controllers for a detailed explanation of the purpose and use of these debugs.

Always-on-tracing

show logging profile wireless filter mac <radio-or-ethernet-AP-mac> to-file always-on-<FILENAME.txt>

RadioActive Tracing

debug wireless mac <MAC> [internal]

!!Reproduce

no debug wireless mac <MAC> [internal]

!! Provide ra_trace file generated in bootflash:

dir bootflash: | i ra_trace

Embedded Packet Capture

Packet Capture filtered on AP IP

ip access-list extended CAP-FILTER

permit ip host <AP_IP> any

permit ip any host <AP_IP>

monitor capture MYCAP clear

monitor capture MYCAP interface Po1 both

monitor capture MYCAP buffer size 100

monitor capture MYCAP match any

monitor capture MYCAP access-list CAP-FILTER

monitor capture MYCAP start

!!Reproduce

monitor capture MYCAP stop

monitor capture MYCAP export flash:|tftp:|http:.../filename.pcap

Packet Capture filtered on Client MAC(available after Cisco IOS® XE 17.1.1s)

monitor capture MYCAP clear

monitor capture MYCAP interface Po1 both

monitor capture MYCAP buffer size 100

monitor capture MYCAP match any

monitor capture MYCAP inner mac <Client_MAC>

monitor capture MYCAP start

!!Reproduce

monitor capture MYCAP stop

monitor capture MYCAP export flash:|tftp:|http:.../filename.pcap

Verify

show monitor capture MYCAP

show monitor capture MYCAP buffer brief/detail/dump

Scenario Specific Log Collection:

WLC Platform Issues

This scenario covers WLC instability due to WLC reloads, switchovers, crashes, high CPU, memory issues.

Outputs to check key performance indicators KPIs to identify if there could be WLC platform issues.

Check for uptime lower than expected, high CPU utilization or WLC crashes.

show ver | i uptime

show redundancy | i Uptime

show proc cpu sorted | i CPU

dir all | i core

Additional logs to collect for WLC platform issues:

Collect crashes/coredumps system-reports/AP crashes. This can be done via GUI: Navigate to Troubleshooting > CoreDump and System Report.

Or via CLI:

# more bootflash:system-report*

# copy bootflash:system-report-YYYYMMDD-HHMMSS-Timezone.tar.gz {tftp: | ftp: | https: ..}

OR

# more harddisk:system-report*

# copy harddisk:system-report-YYYYMMDD-HHMMSS-Timezone.tar.gz {tftp: | ftp: | https: ..}

Also, collect these outputs:

show proc cpu platform sorted 1min

show proc mem platform accounting

show redundancy switchover history

show redundancy history

For any AP crashes, you can collect the AP crash files from WLC GUI>>Configuration>>Wireless>Access Points>> Click on relevant AP >> Advanced tab

AP Join/Connectivity Issues

This scenario covers AP instability due to APs not been able to join WLC, AP disconnections, CAPWAP  tunnel flaps, AP crashes.

Outputs to check key performance indicators KPIs to identify if there could be AP issues:

Check for AP crashes, and for APs with an uptime lower than expected, check for APs that have association uptime lower than expected

show ap uptime

show ap crash-file

dir all | i crash

Additional logs to collect for AP issues:

Always-On Tracing:

show logging profile wireless filter mac <radio-or-ethernet-AP-mac> to-file always-on-<FILENAME.txt>

RadioActive Tracing:

debug wireless mac <AP_Radio_MAC>

debug wireless ip <AP_IP>

Embedded Captures filtered by AP IP address ACL

ip access-list extended CAP-FILTER

permit ip host <AP_IP> any

permit ip any host <AP_IP>

monitor capture MYCAP clear

monitor capture MYCAP interface Po1 both

monitor capture MYCAP buffer size 100

monitor capture MYCAP match any

monitor capture MYCAP access-list CAP-FILTER

monitor capture MYCAP start

!!Reproduce

monitor capture MYCAP stop

monitor capture MYCAP export flash:|tftp:|http:.../filename.pcap

show wireless stats ap discovery

show wireless stats ap join summary

show wireless stats ap history

show tech-support wireless ap

show tech-support wireless ap name <ap-name>

Client Connectivity Issues

This scenario covers client connectivity issues, association issues, authentication issues, disconnections, and roam issues.

Outputs to check key performance indicators KPIs to identify if there could be client connectivity issues:

Check for client delete reasons, identify top delete reason and see if counters increase.

show wireless stats client delete reasons | ex 0

Additional logs to collect for client connectivity issues.

Always-On Tracing:

show logging profile wireless filter mac <Client_MAC> to-file always-on-<FILENAME.txt>

RadioActive Tracing:

debug wireless mac <Client_MAC>

Embedded Captures filtered by client MAC:

monitor capture MYCAP clear

monitor capture MYCAP interface Po1 both

monitor capture MYCAP buffer size 100

monitor capture MYCAP match any

monitor capture MYCAP inner mac <Client_MAC>

monitor capture MYCAP start

!!Reproduce

monitor capture MYCAP stop

monitor capture MYCAP export flash:|tftp:|http:.../filename.pcap

show wireless stats client summary | i MAC|<Client_MAC>

show tech-support wireless client

show tech-support wireless client mac-address <Client_MAC>

Guest Central Web Authentication (CWA) or Local Web Authentication (LWA) Issues

This scenario covers guest client web authentication issues, client does not receive redirect URL, or not able to authenticate.

Outputs to check key performance indicators KPIs to identify if there could be web authentication issues:

Check for clients stuck in webauth state, check the number of intercepted request, received messages and replied error status replies.

show wireless client summary | i Webauth|Number

show wireless stats client detail | i HTTP

Additional logs to collect for web authentication issues:

Always-On Tracing:

show logging profile wireless filter mac <rClient_MAC> to-file always-on-<FILENAME.txt>

RadioActive Tracing:

debug wireless mac <Client_MAC>

Embedded Captures filtered by client MAC:

monitor capture MYCAP clear

monitor capture MYCAP interface Po1 both

monitor capture MYCAP buffer size 100

monitor capture MYCAP match any

monitor capture MYCAP inner mac <Client_MAC>

monitor capture MYCAP start

!!Reproduce

monitor capture MYCAP stop

monitor capture MYCAP export flash:|tftp:|http:.../filename.pcap

show wireless stats client summary | i <Client_MAC>

show wireless stats client delete reasons

show tech wireless client mac-address <Client_MAC>

!!Client WLAN Adapter wireshark captures or Over The Air(OTA) sniffer trace.

show ip http server all

show tcp statistics

show ip traffic

show ip access-list

show tech-support wireless client

show tech-support wireless client mac-address <Client_MAC>

Radio Frequency (RF) or Radio Resource Management(RRM) Issues

Outputs to check key performance indicators KPIs to identify if there could be RF or RRM issues:

Check for APs with the same channel, max transmit power, high channel count or high channel utilization. For more detailed RF analysis use config analyzer.

show ap dot11 [24ghz|5ghz] summary

sh ap auto-rf dot11 [24ghz|5ghz] | i Channel Change Count|Channel Utilization

Additional logs to collect for RF and RRM issues:

set platform software trace wireless chassis active r0 rrm all info

!!Debug txpower logs:

set platform software trace wncd chassis active r0 radio-history-txpower info

!!Debug channel changes logs:

set platform software trace wncd chassis active r0 radio-history-channel info

!!Debug radio resets

set platform software trace wncd chassis active r0 radio-history-reset info

!!Debug DFS events

set platform software trace wncd chassis active r0 radio-history-dfs info

!!Collect and decode traces:

show logging profile wireless internal [to-file <file-name>]

!!Change level back to notice:

set platform software trace wncd chassis active R0 all-modules notice

set platform software trace wireless chassis active R0 rrm all notice

License Issues

Outputs to check key performance indicators KPIs to identify if there could be license issue:

Confirm that WLC is showed as registered and number of APs licensed matches the number of APs.

show license summary | i Status:|AP

sh ap sum | i Number of APs

Additional logs to collect for license issues:

show tech-support license

show logging process ios start last boot to-file bootflash: <file-name>

High Availability issues

Outputs to check Key Performance Indicators (KPIs) to identify if there could be any High Availability issue:

Check uptime for redundancy peers, and if there is any redundancy event.

show redundancy | i ptime

sh log | i REDUNDANCY

Additional logs to collect for High Availability issues

show redundancy states

show redundancy counters

show redundancy switchover history

sh logging onboard uptime !!just for physical WLCs: 9800-40/9800-80/9800-L

show chassis ha-status active

show chassis ha-status standby

sh platform software stack-mgr chassis active R0 sdp-counters

sh platform software stack-mgr chassis standby R0 sdp-counters

sh platform software stack-mgr chassis active R0 peer-timeout

sh platform software stack-mgr chassis standby R0 peer-timeout

Web User Interface or GUI Issues

- Exact screen capture of the error/issue and reproduction steps.

- Web Browser - Name(Firefox, Chrome, and so on,), Browser Version.

- Frontend HTTP Archive Format (HAR) file. The steps are mentioned Generate a HAR file to troubleshoot.

- Frontend console logs. This can be exported out with the steps in Gather Chrome Console Logs.

- Backend Webserver logs. Download from webUI “Troubleshooting > Logs > Web Server Logs”.

Related Information

- Cisco Technical Support & Downloads