Contents

Introduction

Prerequisites

Requirements

Components Used

Local directory

Function

Configuration example

Lab test results

Local speed dial

Function

Configuration example

Lab test results

Personal speed dial

Function

Configuration example

Lab test results

Related Information

Introduction

This document describes configuration examples for the CME contact list.

Contributed by Yiyue Ma, Cisco TAC Engineer.

Prerequisites

Requirements

Cisco recommends that you have knowledge of Cisco Unified Communications Manager Express (CME).

Components Used

The information in this document is based on Cisco Unified Communications Manager Express (CME) 14.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Local directory

Function

Its function is to enter the first name and last name, and then query the DN of the CME local contact.

Configuration example

Set the name display method, with the first name in front and the last name in the back. It needs to be the same as the configuration under voice register dn.

telephony-service

directory last-name-first

Create directory entries. For example, if you have two contacts, you can create two entries. Configure the directory number 10001.

directory entry 1 10001 name san zhang

directory entry 2 10002 name yiyue ma

Configure the directory number and define the identifier as 4. This identifier can be quoted in the voice register pool.

Configure the directory number 10001.

Display name is yiyue ma.

voice register dn 4

number 10002

name yiyue ma

Configure the phone mac address.

Configure the phone type 8851.

Assign the directory number with an identifier of 4 to this phone.

voice register pool 154

id mac xxxxxxx

type 8851

number 1 dn 4

Lab test results

After the configuration is successful, click local directory, then enter the name, and you can query his number.

Local speed dial

Function

System-level list of frequently called numbers that can be programmed on all phones.

An XML file called speeddial.xml must be created and copied to the TFTP server application on the CME router.

A maximum of 32 numbers can be defined.

Configuration example

Create a speeddial.xml file and enter the contact and number.

<CiscoIPPhoneDirectory>

<Title>LOcal Speed Dial</Title>

<Prompt>Record1 to 1 of 1</Prompt>

<DirectoryEntry>

<Name>san zhang</Name>

<Telephone>10001</Telephone>

</DiretoryEnrty>

<Name>si li</Name>

<Telephone>10002</Telephone>

</DiretoryEnrty>

<CiscoIPPhoneDirectory>

Copies the file from the TFTP server to the router flash memory.

1.At the first prompt, enter the IP address or the DNS name of the remote host.

2.At both filename prompts, enter speeddial.xml.

3.At the prompt to erase flash, enter no.

copy tftp flash

Address or name of remote host []? 1.1.1.1

Source filename []? speeddial.xml

Destination filename [speeddial.xml]?

Accessing tftp://1.1.1.1/speeddial.xml...

Erase flash:before copying? [confirm]n

Loading speeddial.xml from 1.1.1.1 (via

FastEthernet0/0):!

[OK - 329 bytes]

Verifying checksum...  OK (0xF5DB)

329 bytes copied in 0.044 secs (7477 bytes/sec)

Enables the Cisco web-browser user interface on the router.

Sets the base HTTP path to flash memory.

ip http server

ip http path flash:

Lab test results

After the configuration is successful, click local speed dial, we can see the CME contact list.

Personal speed dial

Function

Speed dial entries are local to a specific IP phone.

A maximum of 24 numbers per phone can be define.

Configuration example

Configure directory numbers and associated names.

voice register pool 1

fastdial 1 10001 name yiyue ma

fastdial 2 10002 name si li

Lab test results

Related Information

- Cisco Unified Communications Manager Express System Administrator Guide

- Cisco Technical Support & Downloads