Configuration of Setup Wizard on the WAP561

Objective

The Setup Wizard is a set of interactive instructions that guides you through the initial configuration of the WAP561. These instructions cover the basic configurations needed to operate the WAP561. The Access Point Setup Wizard window automatically appears the first time you log in to the WAP but can also be used at any point. This article explains how to configure the WAP561 through the use of the Setup Wizard.

Applicable Device

• WAP561

Software Version

• v1.0.4.2

Configure Setup Wizard

Step 1. Log in to the web configuration utility and choose Run Setup Wizard. The Access Point Setup Wizard window appears.

Step 2. Click Next to continue. The Configure Device - IP Address page opens:

 

Step 3. Click the radio button that corresponds to the method you want to use to determine the IP address of the WAP. 

• Dynamic IP Address (DHCP) (Recommended) — The IP address of the WAP is assigned by a DCHP server. If you choose Dynamic IP Address, skip to Step 9.

• Static IP Address — Allows you to create a fixed (static) IP address for the WAP. A static IP address does not change.

Step 4. In the Static IP Address field, enter the IP address of the WAP. This IP address is created by you and should not be used by another device in the network.

Step 5. In the Subnet Mask field, enter the subnet mask of the IP address.

Step 6. In the Default Gateway field, enter the IP address of the default gateway for the WAP. The default gateway is usually the private IP address assigned to your router.

Step 7. (Optional) In the DNS field, enter the IP address of the primary domain name system (DNS). If you want to access web pages outside of your network, the IP address of the DNS server should be given by your Internet service provider (ISP).

Step 8. (Optional) In the Secondary DNS field, enter the IP address of the secondary DNS.

Step 9. Click Next to continue. The Single Point Setup - Set a Cluster page opens:

Step 10. Click the radio button that corresponds with the cluster settings you would like to use. A cluster allows you to configure multiple access points (APs) as a single device. If you choose not to use a cluster, you have to configure them individually.

• Create a New Cluster — Create a new cluster for APs.

• Join an Existing Cluster — Joins an existing AP cluster in your network.

• Do not Enable Single Point Setup — Single Point Setup (cluster) is not allowed. Skip to Step 13 if you chose this option.

Step 11. In the Cluster Name field, enter either an existing cluster name or create a new cluster name based on your decision in Step 10.

Step 12. In the AP Location field, enter the physical location of the WAP.

Note: If you clicked the Join an Existing Cluster radio button, the WAP configures the rest of the settings based on the cluster. When you click Next, a confirmation page will ask you if you are sure you want to join the cluster. Click Submit to join the cluster. After the configuration is complete, click Finish to exit the Setup Wizard.

Step 13. Click Next to continue. The Configure Device - Set System Date and Time page opens:

Step 14. Choose a time zone from the Time Zone drop-down list.

Step 15. Click the radio button that corresponds with the method you wish to use to set the time of the WAP.

• Network Time Protocol (NTP) — The WAP gets the time from a NTP server.

• Manually — The time is manually entered into the WAP. If you chose manually, skip to Step 17.

Step 16. In the NTP Server field, enter the domain name of the NTP server that provides the date and time. Skip to Step 19.

 

Step 17. From the System Date drop-down lists, choose the month, day, and year respectively.

Step 18. From the System Time drop-down lists, choose the hour and minutes respectively.

Step 19. Click Next to continue. The Enable Security - Set Password page opens:

Step 20. In the New Password field, enter a new password that is required for administrative access on the WAP.

Step 21. In the Confirm Password field, re-enter the same password.

Note: As you enter a password, the number and color of vertical bars changes to indicate the password strength, as follows:

• Red — The password fails to meet the minimum complexity requirements.

• Orange — The password meets the minimum complexity requirements but the password strength is weak.

• Green — The password is strong.

Step 22. (Optional) To enable password complexity, check the Enable check box. This requires that the password is at least 8 characters long and composed of lower and upper case letters and number/symbols.

Step 23. Click Next to continue.  The Configure Radio 1 - Name Your Wireless Network page opens. The WAP561 contains two radios. Each radio functions as an independent WAP and can contain 16 virtual access points. In the initial configuration you only create one access point for each radio.

Step 24. In the Network Name (SSID) field, enter the Service Set Identification (SSID) of the wireless network. The SSID is the name of the wireless local area network.

Step 25. Click Next to continue. The Configure Radio 1 - Secure Your Wireless Network page opens.

Step 26. Click the radio button that corresponds with the network security you would like to apply to your wireless network.

• Best Security (WPA2 Personal - AES) — WPA2 is the second version of WPA security and access control technology for Wi-Fi wireless networking, which includes AES-CCMP encryption. This protocol version provides the best security per the IEEE 802.11i standard. All client stations on the network will need to be able to support WPA2. WPA2 does not allow use of the protocol TKIP (Temporal Key Integrity Protocol) that has known limitations.

• Better Security (WPA Personal - TKIP/AES) — WPA Personal is a Wi-Fi Alliance IEEE 802.11i standard, which includes AES-CCMP and TKIP encryption. It provides security when there are older wireless devices that support the original WPA but do not support the newer WPA2.

• No Security — Wireless network does not require a password and can be accessed by anyone. If you chose No Security, skip to Step 29.

Step 27. In the Security Key field, enter the password for your network.

Step 28. (Optional) To see the password as you type, check the Show Key as Clear Text check box.

Step 29. Click Next to continue. The Configure Radio 1 - Assign The VLAN ID For Your Wireless Network page opens.

Step 30. In the VLAN ID field, enter the ID number of the VLAN that you would like the WAP to belong to.

Note: The VLAN ID should match one of the VLAN IDs that is supported on the port of the remote device that is connected to the WAP.

Step 31. Click Next to continue.  The Configure Radio 2 - Name Your Wireless Network page opens:

Step 32. In the Network Name (SSID) field, enter the Service Set Identification (SSID) of the wireless network.

Step 33. Click Next to continue. The Configure Radio 2 - Secure Your Wireless Network page opens.

Step 34. Click the radio button that corresponds with the network security you would like to apply to your wireless network.

• Best Security (WPA2 Personal - AES) —Provides the best security and is recommended if your wireless devices support this option.

• Better Security — Provides security when there are older wireless devices that do not support WPA2.

• No Security — Wireless network does not require a password and can be accessed by anyone. If you chose No Security, skip to Step 37.

Step 35. In the Security Key field, enter the password for your network.

Step 36. (Optional) To see the password as you type, check the Show Key as Clear Text check box to see the password as you type.

Step 37. Click Next to continue. The Configure Radio 2 - Assign The VLAN ID For Your Wireless Network page opens.

Step 38. In the VLAN ID field, enter the ID number of the VLAN that you would like the WAP to belong to.

Note: The VLAN ID should match one of the VLAN IDs that is supported on the port of the remote device that is connected to the WAP.

Step 39. Click Next to continue. The Enable Captive Portal - Create Your Guest Network page opens:

Step 40. Click the Yes radio button if you would like to create a guest network.  A guest network requires users to be authenticated before they can use the internet. A guest network is not required. Otherwise, click the No radio button if you do not want to create a guest network and skip to Step 54.

Step 41. Click Next to continue. The Enable Captive Portal - Name Your Guest Network page opens:

Step 42. Click the radio button that corresponds with the Radio in which you would like to place the guest network.

Step 43. In the Guest Network name field, enter the SSID of the guest network.

Step 44. Click Next to continue. The Enable Captive Portal - Secure Your Guest Network page opens:

Step 45. Click the radio button that corresponds with the network security you would like to apply to your guest network.

• Best Security (WPA2 Personal - AES) —Provides the best security and is recommended if your wireless devices support this option.

• Better Security — Provides security when there are older wireless devices that do not support WPA2

• No Security — Wireless network does not require a password and can be accessed by anyone. If you chose No Security, skip to Step 48.

Step 46. In the Security Key field, enter the password for the guest network.

Step 47. (Optional) To see the password as you type, check the Show Key as Clear Text check box.

Step 48. Click Next to continue. The Enable Captive Portal - Assign The VLAN ID page opens:

Step 49. In the VLAN ID field, enter the ID number of the VLAN that you would like the guest network to belong to.

Note: The VLAN ID should match one of the VLAN IDs that is supported on the port of the remote device that is connected to the WAP.

Step 50. Click Next to continue. The Enable Captive Portal - Enable Redirect URL page opens:

Step 51. (Optional) To redirect wireless users to a webpage after they log on to the guest network, check the Enable Redirect URL check box. If you do not check the Enable check box, skip to Step 54.

Step 52. In the Redirect URL field, enter the webpage you would like to redirect users to after they log on to the guest network.

Step 53. Click Next to continue. The Summary - Confirm Your Settings page opens:

Step 54. (Optional) If you would like to edit a setting you made, click Back.

Step 55. (Optional) If you would like to exit the Setup Wizard and undo all the changes you made, click Cancel.

Step 56. Review the network and guest network settings. Click Submit to enable the settings on the WAP. A loading bar will appear as the WAP enables your settings. When the WAP is finished, the Finish page opens:

Note: Step 56 will only be applicable if you click Submit on the Confirm Your Settings page.

Step 57. Click Finish to exit the Setup Wizard.