Contents

Introduction

Prerequisites

Requirements

Components Used

Configure

Step A. Log into the AD domain controller and export the SSL certificate used for LDAP.

Step B. Log into the SNA Manager to add the certificate of the LDAP server and the root chain.

Step C. Add the LDAP external service configuration.

SNA Version 7.2 or later

SNA Version 7.1

Step D. Configure Authorization settings.

Local Authorization

Remote Authorization via LDAP

Verify

Troubleshoot

Related Information

Introduction

This document describes the basic configuration of a Secure Network Analytics Manager (formerly Stealthwatch Management Center) version 7.1 or later to use external authentication and, with version 7.2.1 or later, to use external authorization with LDAPS.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

- Cisco Secure Network Analytics (formerly Stealthwatch)

- General LDAP and SSL Operation

- General Microsoft Active Directory management

Components Used

The information in this document is based on these components:

- Cisco Secure Network Analytics Manager (formerly SMC) version 7.3.2

- Windows Server 2016 configured as Active Directory Domain Controller

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Configure

Step A. Log into the AD domain controller and export the SSL certificate used for LDAP.

1. For Windows Server 2012 or later select Run from the Start menu, then enter certlm.msc and continue with step 8.

2. For older Windows Server versions select Run from the Start menu, and then enter mmc.

3. From the File menu, select Add/Remove Snap In.

4. From the Available snap-ins list, select Certificates, then click Add.

5. In the Certificates snap-in window, select Computer account, and then select Next.

6. Leave Local computer selected, and then select Finish.

7. In the Add or Remove Snap-in window, select OK.

8. Navigate to Certificates (Local Computer) > Personal > Certificates

9. Select and right-click the SSL certificate used for LDAPS authentication on your domain controller and click Open.

10. Navigate to the Details tab > click Copy to File > Next

11. Ensure that No, do not export private key is selected and click Next

12. Select Base-64 encoded X.509 format and click Next.

13. Select a location to store the certificate, name the file and click Next.

14. Click Finish, you must get a “The export was successful.” message.

15. Go back to the certificate used for LDAPS, then select the Certification Path tab.

16. Select the Root CA issuer on top of the certification path and click View Certificate.

17. Repeat steps 10-14 to export the certificate of the root CA which signed the certificate used for LDAPS authentication.

Note: Your deployment can have a multi-tier CA Hierarchy, in which case you need to follow the same procedure to export all the intermediate certificates in the trust chain.

18. Before you continue, ensure that you have one certificate file for the LDAPS server and for each issuer authority in the certification path: Root certificate and intermediate certificates (if applicable).

Step B. Log into the SNA Manager to add the certificate of the LDAP server and the root chain.

1. Navigate to Central Management > Inventory.

2. Locate the SNA Manager appliance and click Actions > Edit Appliance Configuration.

3. In the Appliance Configuration window navigate to Configuration Menu > Trust Store > Add New.

4. Type the Friendly Name, click Choose File and select the certificate of the LDAP Server, then click Add Certificate.

5. Repeat the previous step to add the Root CA certificate and intermediate certificates (if applicable).

6. Verify that the certificates which were uploaded are the correct ones and click Apply Settings.

7. Wait for the changes to be applied and for the Manager status to be Up.

Step C. Add the LDAP external service configuration.

SNA Version 7.2 or later

1. Open the Manager main dashboard and navigate to Global Settings > User Management.

2. In the User Management window select the Authentication and Authorization tab.

3. Click Create > Authentication Service.

4. From the Authentication Service drop-down menu select LDAP.

5. Complete the required fields.

Field

Notes

Friendly Name

Enter a name for theLDAPserver.

Description

Enter a description for the LDAP server.

Server Address

Enter the fully qualified domain name as specified in the Subject Alternative Name (SAN) field of the LDAP server certificate.

- If the SAN field contains only the IPv4 address, enter the IPv4 address in the Server Address field.

- If the SAN field contains the DNS name, enter the DNS name in the Server Address field.

- If the SAN field contains both DNS and IPv4 values, use the first value listed.

Port

Enter the port designated for secure LDAP communication (LDAP over TLS). The well known TCP port for LDAPS is 636.

Bind User

Enter the user ID used to connect to the LDAP server. For example: CN=admin,OU=Corporate Users,DC=example,DC=com

Note: If you have added your users to a built-in AD container (For example, "Users"), then the Bind DN of the Bind User must have the canonical name (CN) set to the built-in folder (For instance, CN=username, CN=Users, DC=domain, DC=com). However, if you have added your users to a new container, then the Bind DN must have the organizational unit (OU) set to the new container name (For instance, CN=username, OU=Corporate Users, DC=domain, DC=com).

Note: A useful way to find the Bind DN of the Bind User is to query the Active Directory on a Windows Server which has connectivity to the Active Directory Server. To get this information you can open a Windows command prompt and type the command dsquery user dc=<distinguished>,dc=<name> -name <user>. For example: dsquery user dc=example,dc=com -name user1. The result looks like "CN=user1,OU=Corporate Users,DC=example,DC=com"

Password

Enter the Bind User password used to connect to the LDAP server.

Base Accounts

Enter the Distinguished Name (DN).

The DN applies to the branch of the directory in which searches for users must begin. It is often the top of directory tree (your domain), but you can also specify a sub-tree within the directory. The Bind User and the users intended to be authenticated must be accessible from Base Accounts.

For example: DC=example,DC=com

6. Click Save.

7. If the settings entered and the certificates added to the trust store are correct, you must get a "You've successfully saved your changes" banner.

8. The configured server must be displayed under User Management > Authentication and Authorization.

SNA Version 7.1

1. Navigate to Central Management > Inventory.

2. Locate the SMC appliance and click Actions > Edit Appliance Configuration.

3. In the Appliance Configuration window navigate to Configuration Menu > LDAP Setup > Add New.

4. Complete the required fields as described in SNA Version 7.2 or later step 5.

5. Click Add.

6. Click Apply Settings.

7. Once the settings entered and the certificates added to the trust store are correct, the changes on the Manager are applied and the appliance state must be Up.

Step D. Configure Authorization settings.

SNA supports both Local and Remote Authorization via LDAP. With this configuration, the LDAP groups from the AD Server are mapped to built-in or custom SNA roles.

The supported authentication and authorization methods for SNA via LDAP are:

- Remote Authentication & Local Authorization

- Remote Authentication & Remote Authorization (Only supported for SNA version 7.2.1 or later)

Local Authorization

In this case, the users and their roles need to be defined locally. To achieve this, proceed as follows.

1. Navigate to User Management again, click the Users tab > Create > User.

2. Define the user name to authenticate with the LDAP server and select the configured server from the Authentication Service drop-down menu.

3. Define the permissions that the user must have over the Manager once it's authenticated by the LDAP server and click Save.

Remote Authorization via LDAP

Remote Authentication and Authorization via LDAP was first supported in Secure Network Analytics version 7.2.1.

Note: Remote Authorization with LDAP is not supported in version 7.1.

It is relevant to mention that if a user is defined and enabled locally (in the Manager), then the user is authenticated remotely, but authorized locally. The user selection process is as follows:

1. Once the credentials are entered on the Manager's welcome page, the Manager looks for a local user with the specified name.

2. If a local user is found and it is enabled, it is authenticated remotely (if remote authentication via LDAP with local authorization was configured previously) but authorized with the local settings.

3. If remote authorization is configured and enabled, and the user is not found locally (not configured or disabled), both authentication and authorization are performed remotely.

For this reason, the steps to successfully configure remote Authentication are t..

Step D-1. Disable or delete the users intended to use remote authorization but which are defined locally.

1. Open the Manager main dashboard and navigate to Global Settings > User Management.

2. Disable or delete the users (if they exist) intended to use remote authentication and authorization via LDAP, but are configured locally.

Step D-2. Define cisco-stealthwatch Groups in the Microsoft AD server.

For External Authentication and Authorization via LDAP users, passwords and cisco-stealthwatch groups are defined remotely in Microsoft Active Directory. The cisco-stealthwatch groups to be defined in the AD server are related to the different roles which SNA has, they must be defined as follows.

SNA Role

Group(s) Name

Primary Admin

- cisco-stealthwatch-master-admin

Data Role

- cisco-stealthwatch-all-data-read-and-write

- cisco-stealthwatch-all-data-read-only

- cisco-stealthwatch-<custom> (optional)

Note: Ensure that custom data role groups begin with “cisco-stealthwatch-“.

Web Functional Role

- cisco-stealthwatch-configuration-manager

- cisco-stealthwatch-power-analyst

- cisco-stealthwatch-analyst

Desktop Functional Role

- cisco-stealthwatch-desktop-stealthwatch-power-user

- cisco-stealthwatch-desktop-configuration-manager

- cisco-stealthwatch-desktop-network-engineer

- cisco-stealthwatch-desktop-security-analyst

- cisco-stealthwatch-desktop-<custom> (optional)

Note: Ensure that custom desktop functional role groups begin with “cisco-stealthwatch-desktop-“.

Note: As described previously, custom groups are supported for “Data Role” and “Desktop Functional Role” as long as the group name is prepended with the proper string. These custom roles and groups must be defined in both the SNA Manager and the Active Directory server. For example, if you define a custom role “custom1” in the SNA Manager for a desktop client role, it must be mapped to cisco-stealthwatch-desktop-custom1 in Active Directory.

Step D-3. Define LDAP Authorization Group Mappings for the users.

Once the cisco-stealthwatch groups have been defined in the AD server, we can map the users intended to have access to the SNA Manager to the necessary groups. This must be done as follows.

- A Primary Admin user must be assigned to the cisco-stealthwatch-master-admin group and must not be a member of any other cisco-stealthwatch groups.

- Each user, other than Primary Admin users, must be assigned to a group of each role with the next conditions.

1. Data Role: The user must be assigned to only one group.

2. Web Functional Role: The user must be assigned to at least one group.

3. Desktop Functional Role: The user must be assigned to at least one group.

Step D-4. Enable Remote Authorization via LDAP on the SNA Manager.

1. Open the Manager main dashboard and navigate to Global Settings > User Management.

2. In the User Management window select the Authentication and Authorization tab.

3. Locate the LDAP authentication service which was configured in Step C.

4. Click Actions > Enable Remote Authorization.

Note: Only one external Authorization service can be in use at a time. If another Authorization service is already in use, it is automatically disabled and the new one is enabled, however all users which were authorized with the previous external service are logged out. A confirmation message is displayed before any action takes place.

Verify

The users are able to log in with the credentials defined on the AD server.

The second verification step is in regards to Authorization. In this example, user "user20" was made a member of the cisco-stealthwatch-master-admin group in the AD server, and we can confirm that the user has Primary Admin permissions. The user is not defined in the local users, so we can confirm that the Authorization attributes were sent by the AD server.

The same verification is done for the other user in this example "snauser10". We can confirm successful authentication with the credentials which were configured on the AD server.

For the Authorization verification, as this user does not belong to the Primary Admin group, some features are not available.

Troubleshoot

If the configuration of the Authentication Service cannot be saved successfully verify that:

1. You have added the proper certificates of the LDAP server to the trust store of the Manager.

2. The configured Server Address is as specified in the Subject Alternative Name (SAN) field of the LDAP server certificate.

- If the SAN field contains only the IPv4 address, enter the IPv4 address in the Server Address field.

- If the SAN field contains the DNS name, enter the DNS name in the Server Address field.

- If the SAN field contains both DNS and IPv4 values, use the first value listed.

3. The configured Bind User and Base Account fields are correct, as specified by the AD Domain Controller.

Related Information

For additional assistance, please contact Cisco Technical Assistance Center (TAC). A valid support contract is required: Cisco Worldwide Support Contacts.