Contents

Introduction

Prerequisites

Requirements

Components Used

Background Information

Configure

Network Diagram

Procedure

Configurations

ISE Configuration

Configure the Certificate Authentication Profile

User Configuration

Verify

ISE Verification

Troubleshoot

Enable Debugs on ISE

Log Snippets

Introduction

This document describes how to configure and troubleshoot authorization policies in ISE based on Azure AD group membership with EAP-TLS or TEAP.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

- Identity Services Engine (ISE)

- Microsoft Azure AD, subscription, and apps

- EAP-TLS authentication

Components Used

The information in this document is based on these software and hardware versions:

- Cisco ISE 3.2

- Microsoft Azure AD

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Background Information

In ISE 3.0 it is possible to leverage the integration between ISE and Azure Active Directory (AAD) to authenticate the users based on Azure AD groups and attributes through Resource Owner Password Credentials (ROPC) communication. With ISE 3.2, you can configure certificate-based authentication and users can be authorized based on azure AD group memberships and other attributes. ISE queries Azure through graph API to fetch groups and attributes for the authenticated user, it uses the certificate’s Subject Common Name (CN) against User Principal name (UPN) on the Azure side.

Note: The certificate-based authentications can be either EAP-TLS or TEAP with EAP-TLS as the inner method. Then, you can select attributes from Azure Active Directory and add them to the Cisco ISE dictionary. These attributes can be used for authorization. Only user authentication is supported.

Configure

Network Diagram

The next image provides an example of a network diagram and traffic flow:

Procedure

1. The certificate is sent to ISE through EAP-TLS or TEAP with EAP-TLS as the inner method.

2. ISE evaluates the user’s certificate (validity period, trusted CA, CRL, and so on.)

3. ISE takes the certificate subject name (CN) and performs a look-up to the Microsoft Graph API to fetch the user’s groups and other attributes for that user. This is referred to as User Principal name (UPN) on the Azure side.

4. ISE Authorization policies are evaluated against the user’s attributes returned from Azure.

Note: You must configure and grant the Graph API permissions to ISE app in Microsoft Azure as shown below:

Configurations

ISE Configuration

Note: ROPC functionality and Integration between ISE with Azure AD is out of the scope of this document. It is important that groups and user attributes are added from Azure. See the configuration guide.

Configure the Certificate Authentication Profile

Step 1. Navigate to the Menu icon located in the upper left corner and select Administration > Identity Management > External Identity sources.

Step 2. Select Certificate Authentication Profile and then click on Add.

Step 3. Define the name. Set the Identity Store as [Not applicable], and select Subject – Common Name on Use Identity From field. Select Never on Match Client Certificate against Certificate in Identity Store Field.

Step 4. Click Save:

Step 5. Navigate to the Menu icon located in the upper left corner and select Policy > Policy Sets.

Step 6. Select the plus icon to create a new policy set. Define a name and select Wireless 802.1x or wired 802.1x as conditions. The Default Network Access option is used in this example:

Step 7. Select the arrow next to Default Network Access to configure Authentication and Authorization Policies.

Step 8. Select the Authentication Policy option, define a name and add EAP-TLS as Network Access EAPAuthentication, it is possible to add TEAP as Network Access EAPTunnel if TEAP is used as the authentication protocol. Select the Certificate Authentication Profile created on step 3 and click Save.

Step 9. Select the Authorization Policy option, define a name and add Azure AD group or user attributes as a condition. Choose the profile or security group under Results, depends on the use case, then click Save.

User Configuration

The Subject Common Name (CN) from the user certificate must match the User Principal Name (UPN) on the Azure side in order to retrieve AD group Membership and user attributes that be used in authorization rules. For the authentication to be successful, the root CA and any intermediate CAs certificates must be in ISE Trusted Store.

Verify

ISE Verification

In the Cisco ISE GUI, click the Menu icon and choose Operations > RADIUS > Live Logs for network authentications (RADIUS).

Click the magnifier icon in the Details column to view a detailed authentication report and confirm if the flow works as expected.

1. Verify Authentication/Authorization policies.

2. Authentication method/protocol.

3. User’s subject name taken from the certificate.

4. User groups and other attributes fetched from Azure directory.

Troubleshoot

Enable Debugs on ISE

Navigate to Administration > System > Logging > Debug Log Configuration to set the next components to the specified level.

Node

Component Name

Log Level

Log Filename

PSN

rest-id-store

Debug

rest-id-store.log

PSN

runtime-AAA

Debug

prrt-server.log

Note: When you are done with troubleshooting, remember to reset the debugs. To do so, select the related node and click Reset to Default.

Log Snippets

The next excerpts show the last two phases in the flow, as mentioned earlier in the network diagram section.

1. ISE takes the certificate subject name (CN) and performs a look-up to the Azure Graph API to fetch user’s groups and other attributes for that user. This is referred to as User Principal name (UPN) on Azure side.

2. ISE Authorization policies are evaluated against the user attributes returned from Azure.

Rest-id logs:

Prrt logs: