Contents

Introduction

Prerequisites

Requirements

Components Used

Related Products

Background Information

Configure

Network Diagram

Configurations

Configure Packet Capture with the ASDM

Configure Packet Capture with the CLI

Available Capture Types on the ASA

Defaults

View the Captured Packets

On the ASA

Download from the ASA for Offline Analysis

Clear a Capture

Stop a Capture

Verify

Troubleshoot

Introduction

This document describes how to configure the Cisco ASA firewall to capture the desired packets with the ASDM or the CLI.

Prerequisites

Requirements

This procedure assumes that the ASA is fully operational and is configured in order to allow the Cisco ASDM or the CLI to make configuration changes.

Components Used

This document is not restricted to specific hardware or software versions.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Related Products

This configuration is also used with these Cisco products:

- Cisco ASA Versions 9.1(5) and later

- Cisco ASDM Version 7.2.1

Background Information

This document describes how to configure the Cisco Adaptive Security Appliance (ASA) Next-Generation Firewall in order to capture the desired packets with either the Cisco Adaptive Security Device Manager (ASDM) or the Command Line Interface (CLI) (ASDM).

The packet capture process is useful to troubleshoot connectivity problems or monitor suspicious activity. In addition, it is possible to create multiple captures in order to analyze different types of traffic on multiple interfaces.

Configure

This section provides information used to configure the packet capture features that are described in this document.

Network Diagram

This document uses this network setup:

Configurations

The IP address schemes used in this configuration are not legally routable on the Internet. They are RFC 1918 addresses that are used in a lab environment.

Configure Packet Capture with the ASDM

This example configuration is used in to capture the packets that are transmitted during a ping from User1 (inside network) to Router1 (outside network).

Complete these steps in order to configure the packet capture feature on the ASA with the ASDM:

1. Navigate to Wizards > Packet Capture Wizard to start the packet capture configuration, as shown:

2. The Capture Wizard opens. Click Next.

3.0 In the new window, provide the parameters that are used in to capture the ingress traffic.

3.1 Select inside for the Ingress Interface and provide the source and the destination IP addresses of the packets to be captured, along with their subnet mask, in the respective space provided.

3.2 Choose the packet type to be captured by the ASA (IP is the packet type chosen here), as shown:

3.3 Click Next.

4.1 Select outside for the Egress Interface and provide the source and the destination IP addresses, along with their subnet mask, in the respective spaces provided.

If Network Address Translation (NAT) is performed on the Firewall, take this into consideration as well.

4.2 Click Next.

5.1 Enter the appropriate Packet Size and the Buffer Size in the respective space provided. This data is required for the capture to take place.

5.2 Check the Use circular buffer box to use the circular buffer option. Circular buffers never fill up.

As the buffer reaches its maximum size, older data is discarded and the capture continues.

In this example, circular buffer is not used, so the check box is not checked.

5.3 Click Next.

6.0 This window shows the Access-lists that must be configured on the ASA (so that the desired packets are captured) and the type of packets to be captured (IP packets are captured in this example).

6.1 Click Next.

7. Click Start in order to start the packet capture, as shown:

After the packet capture starts, attempt to ping the outside network from the inside network so that the packets that flow between the source and the destination IP addresses are captured by the ASA capture buffer.

8. Click Get Capture Buffer in order to view the packets that are captured by the ASA capture buffer.

The captured packets are shown in this window for both the ingress and egress traffic.

9. Click Save captures to save the capture information.

10.1 From the Save captures window, choose the required format in which the capture buffer is to be saved. This is either ASCII or PCAP.

10.2 Click the radio button next to the format names.

10.3 Click Save ingress capture or Save egress capture as required. The PCAP files can then be opened with capture analyzers, such as Wireshark, and it is the preferred method.

11.1 From the Save capture file window, provide the file name and the location where the capture file is to be saved.

11.2 Click Save.

12. Click Finish.

This completes the GUI packet capture procedure.

Configure Packet Capture with the CLI

Complete these steps in order to configure the packet capture feature on the ASA with the CLI:

1. Configure the inside and outside interfaces as illustrated in the network diagram with the correct IP address and security levels.

2. Start the packet capture process with the capture command in privileged EXEC mode. In this configuration example, the capture named capin is defined. Bind it to the inside interface, and specify with the match keyword that only the packets that match the traffic of interest are captured:

ASA# capture capin interface inside match ip 192.168.10.10 255.255.255.255

203.0.113.3 255.255.255.255

3. Similarly, the capture named capout is defined. Bind it to the outside interface, and specify with the match keyword that only the packets that match the traffic of interest are captured:

ASA# capture capout interface outside match ip 192.168.10.10 255.255.255.255

203.0.113.3 255.255.255.255
The ASA now begins to capture the traffic flow between the interfaces. In order to stop the capture at anytime, enter the no capture command followed by the capture name.

Here is an example:

no capture capin interface inside

no capture capout interface outside

Available Capture Types on the ASA

This section describes the different types of captures that are available on the ASA.

- asa_dataplane - Captures packets on the ASA backplane that pass between the ASA and a module that uses the backplane, such as the ASA CX or IPS module.

ASA# cap asa_dataplace interface asa_dataplane

ASA# show capture

capture asa_dataplace type raw-data interface asa_dataplane [Capturing - 0 bytes]

- asp-drop drop-code - Captures packets that are dropped by the accelerated security path. The drop-code specifies the type of traffic that is dropped by the accelerated security path.

ASA# capture asp-drop type asp-drop acl-drop

ASA# show cap

ASA# show capture asp-drop

2 packets captured

1: 04:12:10.428093       192.168.10.10.34327 > 10.94.0.51.15868: S

2669456341:2669456341(0) win 4128 <mss 536> Drop-reason: (acl-drop)

Flow is denied by configured rule

2: 04:12:12.427330       192.168.10.10.34327 > 10.94.0.51.15868: S

2669456341:2669456341(0) win 4128 <mss 536> Drop-reason: (acl-drop)

Flow is denied by configured rule

2 packets shown

ASA# show capture asp-drop

2 packets captured

1: 04:12:10.428093       192.168.10.10.34327 > 10.94.0.51.15868: S

2669456341:2669456341(0) win 4128 <mss 536> Drop-reason: (acl-drop)

Flow is denied by configured rule

2: 04:12:12.427330       192.168.10.10.34327 > 10.94.0.51.15868: S

2669456341:2669456341(0) win 4128 <mss 536> Drop-reason: (acl-drop)

Flow is denied by configured rule

2 packets shown

- ethernet-type type - Selects an Ethernet type to capture. Supported Ethernet types include 8021Q, ARP, IP, IP6, LACP, PPPOED, PPPOES, RARP, and VLAN.

This example show how to capture ARP traffic:

ASA# cap arp ethernet-type ?

exec mode commands/options:

802.1Q

<0-65535>  Ethernet type

arp

ip

ip6

pppoed

pppoes

rarp

vlan

cap arp ethernet-type arp interface inside

ASA# show cap arp

22 packets captured

1: 05:32:52.119485       arp who-has 10.10.3.13 tell 10.10.3.12

2: 05:32:52.481862       arp who-has 192.168.10.123 tell 192.168.100.100

3: 05:32:52.481878       arp who-has 192.168.10.50 tell 192.168.100.10

4: 05:32:53.409723       arp who-has 10.106.44.135 tell 10.106.44.244

5: 05:32:53.772085       arp who-has 10.106.44.108 tell 10.106.44.248

6: 05:32:54.782429       arp who-has 10.106.44.135 tell 10.106.44.244

7: 05:32:54.784695       arp who-has 10.106.44.1 tell xx.xx.xx.xxx:

- real-time - Displays the captured packets continuously in real-time. In order to terminate a real-time packet capture, press Ctrl-C. In order to permanently remove the capture, use the no form of this command.

- This option is not supported when you use the cluster exec capture command.

ASA# cap capin interface inside real-time

Warning: using this option with a slow console connection may

result in an excessive amount of non-displayed packets

due to performance limitations.

Use ctrl-c to terminate real-time capture

- Trace - Traces the captured packets in a manner similar to the ASA packet tracer feature.

ASA#cap in interface Webserver trace match tcp any any eq 80

// Initiate Traffic

1: 07:11:54.670299   192.168.10.10.49498 > 198.51.100.88.80: S

2322784363:2322784363(0) win 8192

<mss 1460,nop,wscale 2,nop,nop,sackOK>

Phase: 1

Type: CAPTURE

Subtype:

Result: ALLOW

Config:

Additional Information:

MAC Access list

Phase: 2

Type: ACCESS-LIST

Subtype:

Result: ALLOW

Config:

Implicit Rule

Additional Information:

MAC Access list

Phase: 3

Type: ROUTE-LOOKUP

Subtype: input

Result: ALLOW

Config:

Additional Information:

in   0.0.0.0         0.0.0.0         outside

Phase: 4

Type: ACCESS-LIST

Subtype: log

Result: ALLOW

Config:

access-group any in interface inside

access-list any extended permit ip any4 any4 log

Additional Information:

Phase: 5

Type: NAT

Subtype:

Result: ALLOW

Config:

object network obj-10.0.0.0

nat (inside,outside) dynamic interface

Additional Information:

Dynamic translate 192.168.10.10/49498 to 203.0.113.2/49498

Phase: 6

Type: NAT

Subtype: per-session

Result: ALLOW

Config:

Additional Information:

Phase: 7

Type: IP-OPTIONS

Subtype:

Result: ALLOW

Config:

Additional Information:

Phase: 8

Type:

Subtype:

Result: ALLOW

Config:

Additional Information:

Phase: 9

Type: ESTABLISHED

Subtype:

Result: ALLOW

Config:

Additional Information:

Phase: 10

Type:

Subtype:

Result: ALLOW

Config:

Additional Information:

Phase: 11

Type: NAT

Subtype: per-session

Result: ALLOW

Config:

Additional Information:

Phase: 12

Type: IP-OPTIONS

Subtype:

Result: ALLOW

Config:

Additional Information:

Phase: 13

Type: FLOW-CREATION

Subtype:

Result: ALLOW

Config:

Additional Information:

New flow created with id 41134, packet dispatched to next module

Phase: 14

Type: ROUTE-LOOKUP

Subtype: output and adjacency

Result: ALLOW

Config:

Additional Information:

found next-hop 203.0.113.1 using egress ifc outside

adjacency Active

next-hop mac address 0007.7d54.1300 hits 3170

Result:

output-interface: outside

output-status: up

output-line-status: up

Action: allow

Note: On ASA 9.10+, the any keyword only captures packets with ipv4 addresses. The any6 keyword captures all ipv6 addressed traffic.

These are advanced settings that can be configured with Packet Captures.

Please review the command reference guide on how to set them.

- ikev1/ikev2 - Captures only Internet Key Exchange Version 1 (IKEv1) or IKEv2 protocol information.

- isakmp - Captures Internet Security Association and Key Management Protocol (ISAKMP) traffic for VPN connections. The ISAKMP subsystem does not have access to the upper-layer protocols. The capture is a pseudo capture, with the physical, IP, and UDP layers combined together in order to satisfy a PCAP parser. The peer addresses are obtained from the SA exchange and are stored in the IP layer.

- lacp - Captures Link Aggregation Control Protocol (LACP) traffic. If configured, the interface name is the physical interface name. This is useful when you work with Etherchannels in order to identify the present behavior of LACP.

- tls-proxy - Captures decrypted inbound and outbound data from the Transport Layer Security (TLS) proxy on one or more interfaces.

- webvpn - Captures WebVPN data for a specific WebVPN connection.

Caution: When you enable WebVPN capture, it affects the performance of the security appliance. Ensure that you disable the capture after you generate the capture files that are needed in order to troubleshoot.

Defaults

These are the ASA system default values:

- The default type is raw-data.

- The default buffer size is 512 KB.

- The default Ethernet type is IP packets.

- The default packet-length is 1,518 bytes.

View the Captured Packets

On the ASA

In order to view the captured packets, enter the show capture command followed by the capture name. This section provides the show command outputs of the capture buffer contents. The show capture capin command shows the contents of the capture buffer named capin:

ASA# show cap capin

8 packets captured

1: 03:24:35.526812       192.168.10.10 > 203.0.113.3: icmp: echo request

2: 03:24:35.527224       203.0.113.3 > 192.168.10.10: icmp: echo reply

3: 03:24:35.528247       192.168.10.10 > 203.0.113.3: icmp: echo request

4: 03:24:35.528582       203.0.113.3 > 192.168.10.10: icmp: echo reply

5: 03:24:35.529345       192.168.10.10 > 203.0.113.3: icmp: echo request

6: 03:24:35.529681       203.0.113.3 > 192.168.10.10: icmp: echo reply

7: 03:24:57.440162       192.168.10.10 > 203.0.113.3: icmp: echo request

8: 03:24:57.440757       203.0.113.3 > 192.168.10.10: icmp: echo reply

The show capture capout command shows the contents of the capture buffer named capout:

ASA# show cap capout

8 packets captured

1: 03:24:35.526843       192.168.10.10 > 203.0.113.3: icmp: echo request

2: 03:24:35.527179       203.0.113.3 > 192.168.10.10: icmp: echo reply

3: 03:24:35.528262       192.168.10.10 > 203.0.113.3: icmp: echo request

4: 03:24:35.528567       203.0.113.3 > 192.168.10.10: icmp: echo reply

5: 03:24:35.529361       192.168.10.10 > 203.0.113.3: icmp: echo request

6: 03:24:35.529666       203.0.113.3 > 192.168.10.10: icmp: echo reply

7: 03:24:47.014098       203.0.113.3 > 203.0.113.2: icmp: echo request

8: 03:24:47.014510       203.0.113.2 > 203.0.113.3: icmp: echo reply

Download from the ASA for Offline Analysis

There are a couple of ways to download the packet captures for analysis offline:

1. Navigate to
https://<ip_of_asa>/admin/capture/<capture_name>/pcap
on any browser.

Tip: If you leave out the pcap keyword, then only the equivalent of the show capture <cap_name> command output is provided.

1. Enter the copy capture command and your preferred file transfer protocol in order to download the capture:

copy /pcap capture:<capture-name> tftp://<server-ip-address>

Tip: When you troubleshoot an issue with the use of packet captures, Cisco recommends that you download the captures for offline analysis.

Clear a Capture

In order to clear the capture buffer, enter the clear capture <capture-name> command:

ASA# show capture

capture capin type raw-data interface inside [Capturing - 8190 bytes]

match icmp any any

capture capout type raw-data interface outside [Capturing - 11440 bytes]

match icmp any any

ASA# clear cap capin

ASA# clear cap capout

ASA# show capture

capture capin type raw-data interface inside [Capturing - 0 bytes]

match icmp any any

capture capout type raw-data interface outside [Capturing - 0 bytes]

match icmp any any

Enter the clear capture /all command in order to clear the buffer for all captures:

ASA# clear capture /all

Stop a Capture

The only way to stop a capture on the ASA is to disable it completely with this command:

no capture <capture-name>

Verify

There is currently no verification procedure available for this configuration.

Troubleshoot

There is currently no specific troubleshoot information available for this configuration.