Contents

Introduction

Components Used

BGP Route Announcement

Configuration Example

Topology Diagram

Initial Setup

FlexVPN Server Configuration on the Catalyst 8000v Router

1. Create an IKEv2 Proposal

2. Create an IKEv2 Policy and Associate it with the Proposal.

3. Configure the IKEv2 Authorization Policy

4. Create a IKEv2 Profile

5. Create an IPsec Transform Set

6. Remove Default IPsec Profile

7. Create an IPsec Profile and Associate it with a Transform Set and the IKEv2 Profile.

8. Create a Virtual Template

NFVIS Secure Overlay Minimum Configuration

Review Overlay Status

BGP Route Announcment Configuration for the FlexVPN Server

BGP Configuration on NFVIS

BGP Review

Ensure that the Private Subnets from the FlexVPN Server were Advertised through BGP

Troubleshooting

NFVIS (FlexVPN Client)

NFVIS Log Files

Internal Kernel strongswan injected routes

Review IPsec0 Interface Status

Head-End (FlexVPN Server)

Review IPsec SAs Build Between Peers

Display Active Crypto (encryption) Sessions

Perform Debugs for Additional Troubleshooting

Related Articles and Documentation

Introduction

This document describes how to configure secure overlay and eBGP announcements on NFVIS for exclusive vBranch traffic management.

Components Used

The information in this document is based on these hardware and software components:

- ENCS5412 running NFVIS 4.7.1

- Catalyst 8000v running Cisco IOS® XE 17.09.03a

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

BGP Route Announcement

NFVIS BGP feature works with the secure overlay feature to learn routes from the BGP neighbor over a secure overlay tunnel. These learnt routes or subnets are added into the NFVIS routing table for the secure tunnel, which makes the routes accessible over the tunnel. Since Secure Overlay only permits 1 single private route to be learned from the tunnel; configuring BGP enables overcoming this limitation by establishing adjacency through the encrypted tunnel and injecting exported routes into the NFVIS vpnv4 routing table and viceversa.

Configuration Example

Topology Diagram

The goal for this configuration is to reach the Management IP address of NFVIS from the c8000v. Once the tunnel is established, it is possible to advertise more routes from the private-vrf subnets using eBGP route announcements.

Figure 1. Topology Diagram for the Example prepared on this article

Initial Setup

Configure the relevant IP addressing on the FlexVPN Server (all within global configuration mode)

vrf definition private-vrf

rd 65000:7

address-family ipv4

exit-address-family

vrf definition public-vrf

address-family ipv4

exit-address-family

interface GigabitEthernet1

description Public-Facing Interface

vrf forwarding public-vrf

ip address 209.165.200.226 255.255.255.224

interface Loopback1001

description Tunnel Loopback

vrf forwarding private-vrf

ip address 10.3.3.3 255.255.255.255

interface Loopback80

description Route Announced Loopback

vrf forwarding private-vrf

ip address 172.16.81.81 255.255.255.255

interface GigabitEthernet3

description Route Announced Physical Interface

vrf forwarding private-vrf

ip address 172.16.91.91 255.255.255.0

aaa authorization network default local

For NFVIS, configure the WAN and MGMT interface accordingly

system settings mgmt ip address 192.168.1.1 255.255.255.0

system settings wan ip address 209.165.200.225 255.255.255.224

system settings default-gw 209.165.200.254

system settings ip-receive-acl 0.0.0.0/0

service  [ ssh https netconf scpd ]

action   accept

priority 10

!

FlexVPN Server Configuration on the Catalyst 8000v Router

1. Create an IKEv2 Proposal

It specifies the security protocols and algorithms that two VPN endpoints must use during the initial phase (Phase 1) of establishing a secure communication channel. The purpose of the IKEv2 proposal is to outline the parameters for authentication, encryption, integrity, and key exchange, thereby ensuring that both endpoints agree on a common set of security measures before exchanging any sensitive data.

crypto ikev2 proposal uCPE-proposal

encryption aes-cbc-256

integrity sha512

group 16 14

Where:

encryption <algorithm>

The proposal includes the encryption algorithms (like AES or 3DES) that the VPN must use to protect the data. Encryption prevents eavesdroppers from being able to read the traffic that passes through the VPN tunnel.

integrity <hash>

It specifies the algorithms (such as SHA-512) used for ensuring the integrity and authenticity of the messages exchanged during the IKEv2 negotiation. This prevents tampering and replay attacks.

2. Create an IKEv2 Policy and Associate it with the Proposal.

It is a configuration set that dictates the parameters for the initial phase (phase 1) of establishing an IPsec VPN connection. It primarily focuses on how the VPN endpoints authenticate each other and establish a secure communication channel for the VPN setup.

crypto ikev2 policy uCPE-policy

match fvrf public-vrf

proposal uCPE-proposal

3. Configure the IKEv2 Authorization Policy

IKEv2 is a protocol used to set up a secure session between two endpoints on a network, and the authorization policy is a set of rules that determines what resources and services a VPN client is allowed to access once the VPN tunnel is established.

crypto ikev2 authorization policy uCPE-author-pol

pfs

route set interface Loopback1001

Where:

pfs

Perfect Forward Secrecy (PFS) is a feature that enhances the security of a VPN connection by ensuring that each new encryption key is independently secure, even if previous keys are compromised.

route set interface <interface-name>

When a VPN session is successfully established, the routes defined in the IKEv2 authorization policy are automatically added to the device routing table. This ensures that traffic destined for the networks specified in the route set is correctly routed through the VPN tunnel.

4. Create a IKEv2 Profile

An IKEv2 (Internet Key Exchange version 2) policy is a set of rules or parameters used during the IKEv2 phase of establishing an IPsec (Internet Protocol Security) VPN tunnel. IKEv2 is a protocol that facilitates the secure exchange of keys and negotiation of security associations (SAs) between two parties wishing to communicate securely over an untrusted network, such as the internet. The IKEv2 policy defines how this negotiation must take place, specifying various security parameters that both parties must agree upon to establish a secure and encrypted communication channel.

IKEv2 profile MUST have:

- A local and a remote authentication method.

- A match identity or a match certificate or match any statement.

crypto ikev2 profile uCPE-profile

description uCPE profile

match fvrf public-vrf

match identity remote any

authentication remote pre-share key ciscociscocisco123

authentication local pre-share key ciscociscocisco123

dpd 60 2 on-demand

aaa authorization group psk list default uCPE-author-pol local

virtual-template 1 mode auto

Where:

match fvrf public-vrf

Make a profile vrf-aware.

match identity remote any

Measure to recognize a incoming session as valid; in this case, anyone.

authentication remote pre-share key ciscociscocisco123

Specifies that the remote peer must be authenticated using pre-shared keys.

authentication local pre-share key ciscociscocisco123

Specifies that this device (local) must authenticate using pre-shared keys.

dpd 60 2 on-demand

Dead Peer Detection; if no packets were received over a minutec (60 seconds), send 2 dpd packets within this 60 sec interval.

aaa authorization group psk list default uCPE-author-pol local

Route assignment.

virtual-template 1 mode auto

Bind to a virtual-template.

5. Create an IPsec Transform Set

It defines a set of security protocols and algorithms that must be applied to the data traffic passing through the IPsec tunnel. Essentially, the transform set specifies how the data must be encrypted and authenticated, ensuring secure transmission between VPN endpoints. Tunnel mode configures the IPsec tunnel to encapsulate the entire IP packet for secure transport across the network.

crypto ipsec transform-set tset_aes_256_sha512 esp-aes 256 esp-sha512-hmac

mode tunnel

Where:

set transform-set <transform-set-name>

Specifies the encryption and integrity algorithms (Example: AES for encryption and SHA for integrity) that must be used to protect the data flowing through the VPN tunnel.

set ikev2-profile <ikev2-profile-name>

Defines the parameters for the negotiation of the security associations (SAs) in phase 1 of the VPN setup, including encryption algorithms, hash algorithms, authentication methods, and the Diffie-Hellman group.

set pfs <group>

An optional setting that, if enabled, ensures that each new encryption key is unrelated to any previous key, enhancing security.

6. Remove Default IPsec Profile

Removing the default IPsec profile is a practice adopted for several reasons related to security, customization, and system clarity. The default IPsec profile can not meet the specific security policies or requirements of your network. Removing it ensures that no VPN tunnels inadvertently use suboptimal or insecure settings, reducing the risk of vulnerabilities.

Each network has unique security requirements, including specific encryption and hashing algorithms, key lengths, and authentication methods. Removing the default profile encourages the creation of custom profiles tailored to these specific needs, ensuring the best possible protection and performance.

no crypto ipsec profile default

7. Create an IPsec Profile and Associate it with a Transform Set and the IKEv2 Profile.

An IPsec (Internet Protocol Security) profile is a configuration entity that encapsulates the settings and policies used to establish and manage IPsec VPN tunnels. It serves as a template that can be applied to multiple VPN connections, standardizing security parameters and simplifying the management of secure communication across a network.

crypto ipsec profile uCPE-ips-prof

set security-association lifetime seconds 28800

set security-association idle-time 1800

set transform-set tset_aes_256_sha512

set pfs group14

set ikev2-profile uCPE-profile

8. Create a Virtual Template

The Virtual-Template interface acts as a dynamic template for virtual access interfaces, providing a scalable and efficient way to manage VPN connections. It allows for the dynamic instantiation of Virtual-Access interfaces. When a new VPN session is initiated, the device creates a Virtual-Access interface based on the configuration specified in the Virtual-Template. This process supports a large number of remote clients and sites by dynamically allocating resources as needed without the need for pre-configured physical interfaces for each connection.

By using Virtual-Templates, FlexVPN deployments can scale efficiently as new connections are established, without the need for manual configuration of each individual session.

interface Virtual-Template1 type tunnel

vrf forwarding private-vrf

ip unnumbered Loopback1001

ip mtu 1400

ip tcp adjust-mss 1380

tunnel mode ipsec ipv4

tunnel vrf public-vrf

tunnel protection ipsec profile uCPE-ips-prof

NFVIS Secure Overlay Minimum Configuration

Configure the secure-overlay instance

secure-overlay myconn local-bridge wan-br local-system-ip-addr 10.2.2.2 local-system-ip-subnet 10.2.2.0/27 remote-interface-ip-addr 209.165.200.226 remote-system-ip-addr 10.3.3.3 remote-system-ip-subnet 10.3.3.3/32

ike-cipher aes256-sha512-modp4096 esp-cipher aes256-sha512-modp4096

psk local-psk ciscociscocisco123 remote-psk ciscociscocisco123

commit

Note: When configuring BGP route announcement over an IPSec tunnel, ensure that you configure the secure overlay to use a virtual IP address (not sourced from a physical interface or OVS bridge) for the local tunnel IP address. For the example above, these are the virtual addressing commands changed: local-system-ip-addr 10.2.2.2 local-system-ip-subnet 10.2.2.0/27. Password must be 15 chars minimum.

Review Overlay Status

nfvis# show secure-overlay

secure-overlay myconn

state                           up

active-local-bridge             wan-br

selected-local-bridge           wan-br

active-local-system-ip-addr     10.2.2.2

active-remote-interface-ip-addr 209.165.200.226

active-remote-system-ip-addr    10.3.3.3

active-remote-system-ip-subnet  10.3.3.3/32

active-remote-id                209.165.200.226

BGP Route Announcment Configuration for the FlexVPN Server

This setup must use eBGP for the the peering, where the source address (virtual IP address for the local tunnel IP) subnet from NFVIS side must be added to the listen range.

router bgp 65000

bgp router-id 10.3.3.3

bgp always-compare-med

bgp log-neighbor-changes

bgp deterministic-med

bgp listen range 10.2.2.0/24 peer-group uCPEs

bgp listen limit 255

no bgp default ipv4-unicast

address-family ipv4 vrf private-vrf

redistribute connected

redistribute static

neighbor uCPEs peer-group

neighbor uCPEs remote-as 200

neighbor uCPEs ebgp-multihop 10

neighbor uCPEs timers 610 1835

exit-address-family

Where:

bgp always-compare-med

Configures the router to always compare the MED (Multi-Exit Discriminator) attribute for all routes, regardless of their originating AS.

bgp log-neighbor-changes

Enables logging for events related to changes in BGP neighbor relationships.

bgp deterministic-med

Ensures the comparison of the MED for paths from neighbors in different autonomous systems.

bgp listen range <network>/<mask> peer-group <peer-group-name>

Enables dynamic neighbor discovery within the specified IP range (network/mask) and assigns discovered neighbors to the peer group name. This simplifies configuration by applying common settings to all peers in the group.

bgp listen limit 255

Sets the maximum number of dynamic BGP neighbors that can be accepted within the listen range to 255.

no bgp default ipv4-unicast

Disables the automatic sending of IPv4 unicast routing information to BGP neighbors, requiring explicit configuration to enable this.

redistribute connected

Redistributes routes from directly connected networks into BGP (Private subnets from the FlexVPN server that belong to the private-vrf)

redistribute static

Redistributes static routes into BGP.

neighbor uCPEs ebgp-multihop 10

Allows EBGP (External BGP) connections with peers in the peer group to span up to 10 hops, useful for connecting devices not directly adjacent.

neighbor uCPEs timers <keep-alive> <hold-down>

Sets the BGP keepalive and hold-down timers for neighbors in the peer group respectivley (610 seconds and 1835 seconds for the example).

Note: A outbound prefix list can be configured to control neighbor route advertisements in the peer group: neighbor prefix-list out

BGP Configuration on NFVIS

Start the BGP process with eBGP neighborship settings

router bgp 200

router-id 10.2.2.2

neighbor 10.3.3.3 remote-as 65000

commit

BGP Review

This output reveals the condition of a BGP session as reported by the BIRD Internet Routing Daemon. This routing software is responsible for handling IP routes and making decisions regarding their direction. From the information given, its clear that the BGP session is in an "Established" state, indicating successful completion of the BGP peering process, and the session is currently active. It has successfully imported four routes, and its noted that there is an upper limit of 15 routes that can be imported.

nfvis# support show bgp

BIRD 1.6.8 ready.

name     proto    table    state  since       info

bgp_10_3_3_3 BGP      bgp_table_10_3_3_3 up     09:54:14    Established

Preference:     100

Input filter:   ACCEPT

Output filter:  ACCEPT

Import limit:   15

Action:       disable

Routes:         4 imported, 0 exported, 8 preferred

Route change stats:     received   rejected   filtered    ignored   accepted

Import updates:              4          0          0          0          4

Import withdraws:            0          0        ---          0          0

Export updates:              4          4          0        ---          0

Export withdraws:            0        ---        ---        ---          0

BGP state:          Established

Neighbor address: 10.3.3.3

Neighbor AS:      65000

Neighbor ID:      10.3.3.3

Neighbor caps:    refresh enhanced-refresh AS4

Session:          external multihop AS4

Source address:   10.2.2.2

Route limit:      4/15

Hold timer:       191/240

Keepalive timer:  38/80

Ensure that the Private Subnets from the FlexVPN Server were Advertised through BGP

When configuring BGP route announcement, the only configurable address-family or transmission combination is ipv4 unicastfor IPSec. To view the BGP status, the configurable address-family or transmission for IPSec is vpnv4 unicast.

nfvis# show bgp vpnv4 unicast

Family Transmission Router ID       Local AS Number

vpnv4  unicast      10.2.2.2  200

With the show bgp vpnv4 unicast route command, you can retrieve information about the VPNv4 unicast routes known to the BGP process.

nfvis# show bgp vpnv4 unicast route

Network            Next-Hop        Metric LocPrf Path

172.16.81.81/32    10.3.3.3    0      100    65000 ?

172.16.91.0/24     10.3.3.3    0      100    65000 ?

10.2.2.0/27        10.3.3.3    0      100    65000 ?

10.3.3.3/32        10.3.3.3    0      100    65000 ?

For the head-end VPN server, an overview of the BGP configuration and operational state can be generated to quickly assess the health and configuration of BGP sessions.

c8000v# show ip bgp summary

Number of dynamically created neighbors in vrf private-vrf: 1/(100 max)

Total dynamically created neighbors: 1/(255 max), Subnet ranges: 1

Additional, detailed information about the VPNv4 (VPN over IPv4) routing table entries managed by BGP can be displayed, it must include specific attributes of each VPNv4 route, such as the routes prefix, next-hop IP address, the originating AS number, and various BGP attributes like local preference, MED (Multi-Exit Discriminator), and community values.

c8000v# show ip bgp vpnv4 all

BGP table version is 5, local router ID is 10.3.3.3

Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,

r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,

x best-external, a additional-path, c RIB-compressed,

t secondary path, L long-lived-stale,

Origin codes: i - IGP, e - EGP, ? - incomplete

RPKI validation codes: V valid, I invalid, N Not found

Network          Next Hop            Metric LocPrf Weight Path

Route Distinguisher: 65000:7 (default for vrf private-vrf)

*>   10.2.2.0/27

0.0.0.0                  0         32768 ?

*>   172.16.81.81/32    0.0.0.0                  0         32768 ?

*>   172.16.91.0/24    0.0.0.0                  0         32768 ?

*>   10.3.3.3/32

0.0.0.0                  0         32768 ?

Troubleshooting

NFVIS (FlexVPN Client)

NFVIS Log Files

You can view all initialization and error logs for the IPsec phases from the NFVIS charon.log log file:

nfvis# show log charon.log

Feb  5 07:55:36.771 00[JOB] spawning 16 worker threads

Feb  5 07:55:36.786 05[CFG] received stroke: add connection 'myconn'

Feb  5 07:55:36.786 05[CFG] added configuration 'myconn'

Feb  5 07:55:36.787 06[CFG] received stroke: initiate 'myconn'

Feb  5 07:55:36.787 06[IKE] <myconn|1> initiating IKE_SA myconn[1] to 209.165.200.226

Feb  5 07:55:36.899 06[ENC] <myconn|1> generating IKE_SA_INIT request 0 [ SA KE No N(NATD_S_IP) N(NATD_D_IP) N(FRAG_SUP) N(HASH_ALG) N(REDIR_SUP) V ]

Feb  5 07:55:36.899 06[NET] <myconn|1> sending packet: from 209.165.200.225[500] to 209.165.200.226[500] (741 bytes)

Feb  5 07:55:37.122 09[NET] <myconn|1> received packet: from 209.165.200.226[500] to 209.165.200.225[500] (807 bytes)

Feb  5 07:55:37.122 09[ENC] <myconn|1> parsed IKE_SA_INIT response 0 [ SA KE No V V V V N(NATD_S_IP) N(NATD_D_IP) CERTREQ N(HTTP_CERT_LOOK) ]

Feb  5 07:55:37.122 09[IKE] <myconn|1> received Cisco Delete Reason vendor ID

Feb  5 07:55:37.122 09[ENC] <myconn|1> received unknown vendor ID: 43:49:53:43:4f:56:50:4e:2d:52:45:56:2d:30:32

Feb  5 07:55:37.122 09[ENC] <myconn|1> received unknown vendor ID: 43:49:53:43:4f:2d:44:59:4e:41:4d:49:43:2d:52:4f:55:54:45

Feb  5 07:55:37.122 09[IKE] <myconn|1> received Cisco FlexVPN Supported vendor ID

Feb  5 07:55:37.122 09[CFG] <myconn|1> selected proposal: IKE:AES_CBC_256/HMAC_SHA2_512_256/PRF_HMAC_SHA2_512/MODP_4096

Feb  5 07:55:37.235 09[IKE] <myconn|1> cert payload ANY not supported - ignored

Feb  5 07:55:37.235 09[IKE] <myconn|1> authentication of '209.165.200.225' (myself) with pre-shared key

Feb  5 07:55:37.235 09[IKE] <myconn|1> establishing CHILD_SA myconn{1}

Feb  5 07:55:37.236 09[ENC] <myconn|1> generating IKE_AUTH request 1 [ IDi N(INIT_CONTACT) IDr AUTH SA TSi TSr N(MOBIKE_SUP) N(ADD_4_ADDR) N(ADD_4_ADDR) N(ADD_4_ADDR) N(ADD_4_ADDR) N(ADD_4_ADDR) N(ADD_4_ADDR) N(EAP_ONLY) N(MSG_ID_SYN_SUP) ]

Feb  5 07:55:37.236 09[NET] <myconn|1> sending packet: from 209.165.200.225[4500] to 209.165.200.226[4500] (480 bytes)

Feb  5 07:55:37.322 10[NET] <myconn|1> received packet: from 209.165.200.226[4500] to 209.165.200.225[4500] (320 bytes)

Feb  5 07:55:37.322 10[ENC] <myconn|1> parsed IKE_AUTH response 1 [ V IDr AUTH SA TSi TSr N(SET_WINSIZE) N(ESP_TFC_PAD_N) N(NON_FIRST_FRAG) ]

Feb  5 07:55:37.323 10[IKE] <myconn|1> authentication of '209.165.200.226' with pre-shared key successful

Feb  5 07:55:37.323 10[IKE] <myconn|1> IKE_SA myconn[1] established between 209.165.200.225[209.165.200.225]...209.165.200.226[209.165.200.226]

Feb  5 07:55:37.323 10[IKE] <myconn|1> scheduling rekeying in 86190s

Feb  5 07:55:37.323 10[IKE] <myconn|1> maximum IKE_SA lifetime 86370s

Feb  5 07:55:37.323 10[IKE] <myconn|1> received ESP_TFC_PADDING_NOT_SUPPORTED, not using ESPv3 TFC padding

Feb  5 07:55:37.323 10[CFG] <myconn|1> selected proposal: ESP:AES_CBC_256/HMAC_SHA2_512_256/NO_EXT_SEQ

Feb  5 07:55:37.323 10[IKE] <myconn|1> CHILD_SA myconn{1} established with SPIs cfc15900_i 49f5e23c_o and TS 10.2.2.0/27 === 0.0.0.0/0

Feb  5 07:55:37.342 11[NET] <myconn|1> received packet: from 209.165.200.2264[4500] to 209.165.200.225[4500] (384 bytes)

Feb  5 07:55:37.342 11[ENC] <myconn|1> parsed INFORMATIONAL request 0 [ CPS(SUBNET VER U_PFS) ]

Feb  5 07:55:37.342 11[IKE] <myconn|1> Processing informational configuration payload CONFIGURATION

Feb  5 07:55:37.342 11[IKE] <myconn|1> Processing information configuration payload of type CFG_SET

Feb  5 07:55:37.342 11[IKE] <myconn|1> Processing attribute INTERNAL_IP4_SUBNET

Feb  5 07:55:37.342 11[ENC] <myconn|1> generating INFORMATIONAL response 0 [ ]

Feb  5 07:55:37.342 11[NET] <myconn|1> sending packet: from 209.165.200.225[4500] to 209.165.200.226[4500] (96 bytes)

Internal Kernel strongswan injected routes

On Linux, strongswan (multiplatform IPsec implementation used by NFVIS) installs routes (including BGP VPNv4 unicast routes) into routing table 220by default and hence requires the kernel to support policy based routing.

nfvis# support show route 220

10.2.2.0/27 dev ipsec0 proto bird scope link

172.16.81.81 dev ipsec0 proto bird scope link

172.16.91.0/24 dev ipsec0 proto bird scope link

10.3.3.3 dev ipsec0 scope link

Review IPsec0 Interface Status

You can get further details about the ipsec0 virtual interface with the use of ifconfig

nfvis# support show ifconfig ipsec0

ipsec0: flags=209<UP,POINTOPOINT,RUNNING,NOARP>  mtu 9196

inet 10.2.2.2  netmask 255.255.255.255  destination 10.2.2.2

tunnel   txqueuelen 1000  (IPIP Tunnel)

RX packets 5105  bytes 388266 (379.1 KiB)

RX errors 0  dropped 0  overruns 0  frame 0

TX packets 5105  bytes 389269 (380.1 KiB)

TX errors 1  dropped 0 overruns 0  carrier 1  collisions 0

Head-End (FlexVPN Server)

Review IPsec SAs Build Between Peers

From the output bellow, the encrypted tunnel is built between 209.165.200.226 through the Virtual-Access1 interface and 209.165.200.225 for traffic that goes between networks 0.0.0.0/0 and 10.2.2.0/27; two Encapsulating Security Payload (ESP)SAs built inbound and outbound.

c8000v# show crypto ipsec sa

interface: Virtual-Access1

Crypto map tag: Virtual-Access1-head-0, local addr 209.165.200.226

protected vrf: private-vrf

local  ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)

remote ident (addr/mask/prot/port): (10.2.2.0/255.255.255.224/0/0)

current_peer 209.165.200.225 port 4500

PERMIT, flags={origin_is_acl,}

#pkts encaps: 218, #pkts encrypt: 218, #pkts digest: 218

#pkts decaps: 218, #pkts decrypt: 218, #pkts verify: 218

#pkts compressed: 0, #pkts decompressed: 0

#pkts not compressed: 0, #pkts compr. failed: 0

#pkts not decompressed: 0, #pkts decompress failed: 0

#send errors 0, #recv errors 0

local crypto endpt.: 209.165.200.226, remote crypto endpt.: 209.165.200.225

plaintext mtu 1422, path mtu 1500, ip mtu 1500, ip mtu idb GigabitEthernet1

current outbound spi: 0xC91BCDE0(3374042592)

PFS (Y/N): Y, DH group: group16

inbound esp sas:

spi: 0xB80E6942(3087952194)

transform: esp-256-aes esp-sha512-hmac ,

in use settings ={Tunnel, }

conn id: 2123, flow_id: CSR:123, sibling_flags FFFFFFFF80000048, crypto map: Virtual-Access1-head-0, initiator : False

sa timing: remaining key lifetime (k/sec): (4607969/27078)

IV size: 16 bytes

replay detection support: Y

Status: ACTIVE(ACTIVE)

inbound ah sas:

inbound pcp sas:

outbound esp sas:

spi: 0xC91BCDE0(3374042592)

transform: esp-256-aes esp-sha512-hmac ,

in use settings ={Tunnel, }

conn id: 2124, flow_id: CSR:124, sibling_flags FFFFFFFF80000048, crypto map: Virtual-Access1-head-0, initiator : False

sa timing: remaining key lifetime (k/sec): (4607983/27078)

IV size: 16 bytes

replay detection support: Y

Status: ACTIVE(ACTIVE)

outbound ah sas:

outbound pcp sas:

Display Active Crypto (encryption) Sessions

The output for the show crypto session detail must provide comprehensive details about each active crypto session, including the type of VPN (such as site-to-site or remote access), the encryption and hashing algorithms in use, and the security associations (SAs) for both inbound and outbound traffic. As it also displays statistics about the encrypted and decrypted traffic, such as the number of packets and bytes; this can be useful for monitoring the amount of data being secured by the VPN and for troubleshooting throughput issues.

c8000v# show crypto session detail

Crypto session current status

Code: C - IKE Configuration mode, D - Dead Peer Detection

K - Keepalives, N - NAT-traversal, T - cTCP encapsulation

X - IKE Extended Authentication, F - IKE Fragmentation

R - IKE Auto Reconnect, U - IKE Dynamic Route Update

S - SIP VPN

Interface: Virtual-Access1

Profile: uCPE-profile

Uptime: 11:39:46

Session status: UP-ACTIVE

Peer: 209.165.200.225 port 4500 fvrf: public-vrf ivrf: private-vrf

Desc: uCPE profile

Phase1_id: 209.165.200.225

Session ID: 1235

IKEv2 SA: local 209.165.200.226/4500 remote 209.165.200.225/4500 Active

Capabilities:D connid:2 lifetime:12:20:14

IPSEC FLOW: permit ip   0.0.0.0/0.0.0.0 10.2.2.0/255.255.255.224

Active SAs: 2, origin: crypto map

Inbound:  #pkts dec'ed 296 drop 0 life (KB/Sec) 4607958/7 hours, 20 mins

Outbound: #pkts enc'ed 296 drop 0 life (KB/Sec) 4607977/7 hours, 20 mins

The clear cryptocommands are used to manually reset VPN connections, or clearing security associations (SAs) without needing to reboot the entire device.

- clear crypto ikev2 would clears IKEv2 security associations (IKEv2 SAs).

- clear crypto session would clear IKEv1 (isakmp)/IKEv2 and IPSec SAs.

- clear crypto sa would clear only the IPSec SAs.

- clear crypto ipsec sa would delete the active IPSec security associations.

Perform Debugs for Additional Troubleshooting

IKEv2 debugs can help identifying and troubleshooting errors on the head-end device (c8000v) that can occur during the IKEv2 negotiation process and FlexVPN client connections, such as problems with establishing the VPN session, policy application, or any client-specific errors.

c8000v# terminal no monitor

c8000v(config)# logging buffer 1000000

c8000v(config)# logging buffered debugging

c8000v# debug crypto ikev2 error

c8000v# debug crypto ikev2 internal

c8000v# debug crypto ikev2 client flexvpn

Related Articles and Documentation

Secure Overlay and Single IP Configuration

BGP Support on NFVIS

Secure Overlay and BGP Commands