Contents

Introduction

Prerequisites

Requirements

Components Used

Conventions

An Overview of the Traps Enabled on Your Device

Traps Sent When You Enable Commands from the List

Related Information

Introduction

This document describes the traps sent when you configure the snmp-server enable traps command on a Cisco device.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

- How to configure Simple Network Management Protocol (SMNP) on a Cisco device.

- Use of SNMP get and walk commands.

Components Used

This document applies to Cisco devices (routers and switches) that run Cisco IOS® which supports SNMP. The information in this document is based on several releases of Cisco IOS® because the trap command differs from release to release and platform to platform. For example, you do not have the capacity to send ATM related traps on a system that has no ATM interface.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

An Overview of the Traps Enabled on Your Device

In order to get an overview of the traps you have enabled on your device, issue this command on every Cisco IOS device:

cognac#configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

cognac(config)#snmp-server enable traps ?

atm          Enable SNMP atm traps

bgp          Enable BGP state change traps

config       Enable SNMP config traps

dial         Enable SNMP dial control traps

dlsw         Enable SNMP dlsw traps

dsp          Enable SNMP dsp traps

entity       Enable SNMP entity traps

envmon       Enable SNMP environmental monitor traps

frame-relay  Enable SNMP frame-relay traps

hsrp         Enable SNMP HSRP traps

ipmulticast  Enable SNMP ipmulticast traps

isdn         Enable SNMP isdn traps

msdp         Enable SNMP MSDP traps

rsvp         Enable RSVP flow change traps

rtr          Enable SNMP Response Time Reporter traps

snmp         Enable SNMP traps

syslog       Enable SNMP syslog traps

tty          Enable TCP connection traps

voice        Enable SNMP voice traps

xgcp         Enable XGCP protocol traps

<cr>

cognac(config)#

Once you know the traps you have enabled, you can enable them as you need. This document helps you find which traps are sent when you enable a command.

Note: This list can differ from platform to platform and release to release because of the features in a specific device and available interfaces.

Traps Sent When You Enable Commands from the List

aaa-server

Sends AAA server notifications.

12.1(3)T

AS5300 AS5800

CISCO-AAA-SERVER-MIB

1.3.6.1.4.1.9.10.56.2.0.1

casServerStateChange

bgp

Sends Border Gateway Protocol (BGP) state change notifications.

/

/

BGP4-MIB

1.3.6.1.2.1.15.7.1

bgpEstablished bgpBackwardTransition

calltracker

Sends notification whenever a new active call entry is created in the cctActiveTable or a new history call entry is created in the cctHistoryTable.

/

/

CISCO-CALL-TRACKER-MIB

1.3.6.1.4.1.9.9.163.2.0.1 1.3.6.1.4.1.9.9.163.2.0.2

cctCallSetupNotification cctCallTerminateNotification

config

Sends configuration notifications.

/

/

CISCO-CONFIG-MAN-MIB

1.3.6.1.4.1.9.9.43.2.0.1

ciscoConfigManEvent

dial

Sends notification whenever:

- A successful call clears.

- A failed call attempt is determined to have ultimately failed.

- Whenever a call setup message is received or sent.

/

/

DIAL-CONTROL-MIB

1.3.6.1.2.1.10.21.2.0.1 1.3.6.1.2.1.10.21.2.0.2

dialCtlPeerCallInformation dialCtlPeerCallSetup

dlsw

Sends notifications from DLSw agents. When the dlsw keyword is used, you can specify a notification-option value.

/

/

CISCO-DLSW-MIB

1.3.6.1.4.1.9.10.9.1.7.1 1.3.6.1.4.1.9.10.9.1.7.2 1.3.6.1.4.1.9.10.9.1.7.3 1.3.6.1.4.1.9.10.9.1.7.4 1.3.6.1.4.1.9.10.9.1.7.5 1.3.6.1.4.1.9.10.9.1.7.6

ciscoDlswTrapTConnPartnerReject ciscoDlswTrapTConnProtViolation ciscoDlswTrapTConnUp ciscoDlswTrapTConnDown ciscoDlswTrapCircuitUp ciscoDlswTrapCircuitDown

ds0-busyout

Sends notification whenever the busyout of a DS0 interface changes state.

12.1(3)T

AS5300

CISCO-POP-MGMT-MIB

1.3.6.1.4.1.9.10.19.2.0.1

cpmDS0BusyoutNotification

ds1-loopback

Sends notification whenever the DS1 interface goes into loopback mode.

12.1(3)T

AS5300

CISCO-POP-MGMT-MIB

1.3.6.1.4.1.9.10.19.2.0.2

cpmDS1LoopbackNotification

dspu

Sends notification whenever the operational state of the physical unit (PU) or the logical unit (LU) changes or activation failure is detected.

/

/

CISCO-DSPU-MIB

1.3.6.1.4.1.9.9.24.1.4.4.0.1 1.3.6.1.4.1.9.9.24.1.4.4.0.2 1.3.6.1.4.1.9.9.24.1.5.3.0.1 1.3.6.1.4.1.9.9.24.1.5.3.0.2

newdspuPuStateChangeTrap newdspuPuActivationFailureTrap newdspuLuStateChangeTrap dspuLuActivationFailureTrap

dsp

Sends notification whenever the DSP card goes up or down.

/

/

CISCO-DSP-MGMT-MIB

1.3.6.1.4.1.9.9.86.2.0.1

cdspMIBCardStateNotification

entity

Sends Entity MIB modification notifications.

/

/

ENTITY-MIB

1.3.6.1.2.1.47.2.0.1

entConfigChange

envmon

Sends Cisco enterprise-specific environmental monitor notifications when an environmental threshold is exceeded. When the envmon keyword is used, you can specify a notification-option value.

/

/

CISCO-ENVMON-MIB

1.3.6.1.4.1.9.9.13.3.0.1 1.3.6.1.4.1.9.9.13.3.0.2 1.3.6.1.4.1.9.9.13.3.0.3 1.3.6.1.4.1.9.9.13.3.0.4 1.3.6.1.4.1.9.9.13.3.0.5

ciscoEnvMonShutdownNotification ciscoEnvMonVoltageNotification ciscoEnvMonTemperatureNotification ciscoEnvMonFanNotification ciscoEnvMonRedundantSupplyNotification

frame-relay

Sends Frame Relay notifications.

/

/

RFC1315-MIB

1.3.6.1.2.1.10.32.0.1

frDLCIStatusChange

hsrp

Sends Hot Standby Router Protocol (HSRP) notifications.

12.0(3)T

/

CISCO-HSRP-MIB

1.3.6.1.4.1.9.9.106.2.0.1

cHsrpStateChange

isdn

Sends Integrated Services Digital Network (ISDN) notifications. When the isdn keyword is used, you can specify a notification-option value.

12.1(1)T 12.1(5)T

/

CISCO-ISDN-MIB CISCO-ISDNU-IF-MIB

1.3.6.1.4.1.9.9.26.2.0.1 1.3.6.1.4.1.9.9.26.2.0.2 1.3.6.1.4.1.9.9.26.2.0.3 1.3.6.1.4.1.9.9.26.2.0.4 1.3.6.1.4.1.9.9.18.2.0.1

demandNbrCallInformation demandNbrCallDetails demandNbrLayer2Change demandNbrCNANotification ciuIfLoopStatusNotification

msdp

Sends Multicast Source Discovery Protocol (MSDP) notifications.

/

/

MSDP-MIB

1.3.6.1.3.92.1.1.7.1 1.3.6.1.3.92.1.1.7.2

msdpEstablished msdpBackwardTransition

repeater

Sends Ethernet hub repeater notifications.

/

Cisco-HUB

CISCO-REPEATER-MIB

1.3.6.1.4.1.9.9.22.3.0.1

ciscoRptrIllegalSrcAddrTrap

rsvp

Sends Resource Reservation Protocol (RSVP) notifications.

/

/

RSVP-MIB

1.3.6.1.2.1.51.3.0.1 1.3.6.1.2.1.51.3.0.2

newFlow lostFlow

rtr

Sends Service Assurance Agent RTR (RTR) notifications.

/

/

CISCO-RTTMON-MIB

1.3.6.1.4.1.9.9.42.2.0.1 1.3.6.1.4.1.9.9.42.2.0.2 1.3.6.1.4.1.9.9.42.2.0.3

rttMonConnectionChangeNotification rttMonTimeoutNotification rttMonThresholdNotification

snmp

Sends Simple Network Management Protocol (SNMP) notifications.

/

/

CISCO-GENERAL-TRAPS

1.3.6.1.6.3.1.1.5.1 1.3.6.1.6.3.1.1.5.3 1.3.6.1.6.3.1.1.5.4 1.3.6.1.6.3.1.1.5.5

coldStart linkDown linkUp authenticationFailure egpNeighborLoss reload

syslog

Sends error message notifications (Cisco Syslog MIB). Specify the level of messages to be sent with the log history level command.

/

/

CISCO-SYSLOG-MIB

1.3.6.1.4.1.9.9.41.2.0.1

clogMessageGenerated

voice

Sends poor quality of voice notification.

/

/

CISCO-VOICE-DIAL-CONTROL-MIB

1.3.6.1.4.1.9.9.63.2.0.1

cvdcPoorQoVNotification

xgcp

Sends External Media Gateway Control Protocol (XGCP) notifications.

/

/

XGCP-MIB

1.3.6.1.3.90.2.0.1

xgcpUpDownNotification

channel-failures

This trap indicates that a significant link event has been recognized and resulted in the degradation of the interface line quality.

/

/

CISCO-CHANNEL-MIB

1.3.6.1.4.1.9.9.20.1.5.1 1.3.6.1.4.1.9.9.20.1.5.2

cipCardLinkFailure cipCardDtrBrdLinkFailure

llc2

Sends Logical Link Control, type2 notifications

/

/

CISCO-SDLLC-MIB

1.3.6.1.4.1.9.9.28.2.1

convSdllcPeerStateChangeNotification

rsrb

Indicates that the state of an RSRB remote peer has transitioned to Active or Inactive.

/

/

CISCO-RSRB-MIB

1.3.6.1.4.1.9.9.29.2.1

rsrbPeerStateChangeNotification

sdlc

Indicates that the state of an SDLC port has transitioned. Indicates that the state of an SDLC station has transitioned to Contacted or Discontacted. Indicates that the state of an SDLC link has transitioned to Contacted or Discontacted.

/

/

SNA-SDLC-MIB

1.3.6.1.2.1.41.1.3.1 1.3.6.1.2.1.41.1.3.2 1.3.6.1.2.1.41.1.3.3

sdlcPortStatusChange sdlcLSStatusChange sdlcLSStatusChange1

stun

Indicated that the state of a STUN route has transitioned to Active or Inactive.

/

/

CISCO-STUN-MIB

1.3.6.1.4.1.9.9.30.2.1

stunPeerStateChangeNotification

Related Information

- Cisco Technical Support & Downloads