Contents

Introduction

Prerequisites

Requirements

Components Used

RUM Report

Configure

RUM Report Configurations

Verify

Introduction

This document describes how to license network devices using Resource Utilization Measurement (RUM) Report over Cisco DNA Center.

Prerequisites

Requirements

Cisco recommends that you have knowledge of these topics:

- Cisco UCS M4 or M5 appliance, 44, 55, or 112 cores.

- Cisco DNA Center software.

- Licensing on Cisco IOS® XE.

Components Used

The information in this document is based on Cisco DNA Center running release 2.3.3.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, ensure that you understand the potential impact of any command.

RUM Report

On Cisco DNA Center release 2.2.1 and Cisco IOS XE devices running 17.3.2 or later this licensing method is implemented. Network devices are no longer required to get registered with the Cisco Smart Software Manager (CSSM) Portal. The license usage information is stored in a secure location on the network device, which is called RUM or Usage Report. Over Cisco DNA Center you can pull the report and upload it to CSSM Portal. Additionally, the process can be done periodically or on-demand basis. The CSSM does the proper changes on the Virtual Account and sends an acknowledgement to Cisco DNA Center if the report is good. Finally, Cisco DNA Center updates the license status on GUI and on the network device itself.

Configure

Verify that the network devices chosen for reporting meet these prerequisites:

- The network device is reachable and managed from Cisco DNA Center.

- Netconf port is configured on device credentials.

- There is no FireWall blocking any transfer-related protocol between Cisco DNA Center and the network devices.

Tip: The SSM Connection Mode configuration on Cisco DNA Center set to On-Prem is not supported for RUM Report.

RUM Report Configurations

Step 1. From the Cisco DNA Center menu, navigate to Tools > License Manager.

Menu Location

Step 2. Click the Reporting tab in order to see the Smart License Compliance tool.

Smart License Compliance Tool

Warning: If this workflow is not displayed, you are missing a prerequisite.

Step 3. Click the Smart License Compliance tool in order to start the workflow.

Workflow Start

Step 4. Choose which Smart Account to use and click Next.

Smart Account Selection

Step 5. Choose the device or devices that you want to generate the report for.

Devices list

Warning: If you do not see devices listed here, it means that you do not match the prerequisites for the network devices.

Step 6. Confirm that the Policy Settings are displayed and click Next.

Policy Settings

Note: The default reporting interval time is 90 days.

Step 7. Confirm that all the chosen devices appear on the summary page and click Next.

Step 8. The RUM workflow is configured and running. You must see a progress bar like this one:

Progress bar 1

Step 8.1. Cisco DNA Center generates the Report on the Cisco IOS XE device and transfers it to itself with the first two commands, and then deletes it with the third one.

Report commands 1

Step 9. Once the transfer from the network device to Cisco DNA Center is finished, the progress bar must look like this:

Progress bar 2

At this point Cisco DNA Center sends the report to the CSSM portal and the portal must reply with an acknowledgment message. This can take time depending on the internet speed.

Step 9.1. If there are no issues between Cisco DNA Center and CSSM Portal, you can see this result:

Success Message

Step 9.2. Cisco DNA Center receives the acknowledgment message from the CSSM and imports it to the network device.

Copy Acknowledgment Message

Then, it activates the Rumack.txt file.

Activate Acknowledgment

Finally, it removes the Rumack.txt file for security purposes.

Delete Acknowledgment

Verify

From the Cisco DNA Center menu, navigate to Tools > License Manager. Click the Reporting tab, and scroll down to the Smart License Compliance tool.

You can access the Smart License Enabled Devices table, where you can also view the device details.

Device Confirmation