Konfigurieren von PPPoE über BDI auf Routern der Serie ASR1k
Inhalt
Einführung
In diesem Dokument wird beschrieben, wie der Point-to-Point Protocol over Ethernet (PPPoE)-Server mit der Bridge Domain Interface (BDI) und dem VLAN-Bereich konfiguriert wird.
Voraussetzungen
Anforderungen
Cisco empfiehlt, über Kenntnisse in folgenden Bereichen zu verfügen:
- End-to-End-Layer-1-Anbindung ist in Ordnung
- Grundlagen von PPP und PPPoE sind gut bekannt
Verwendete Komponenten
Die Informationen in diesem Dokument basieren auf den folgenden Software- und Hardwareversionen:
- HOST-1 - CISCO887G
- HOST-2 - CISCO887
- SWITCH - WS-C3560-24TS-S
- PPPoE-SERVER - ASR1001-X
Die Informationen in diesem Dokument wurden von den Geräten in einer bestimmten Laborumgebung erstellt. Alle in diesem Dokument verwendeten Geräte haben mit einer leeren (Standard-)Konfiguration begonnen. Wenn Ihr Netzwerk in Betrieb ist, stellen Sie sicher, dass Sie die potenziellen Auswirkungen eines Befehls verstehen.
Konfigurieren
HOST-1
!
interface FastEthernet0
switchport access vlan 100
no ip address
end
!
interface Vlan100
no ip address
pppoe enable group global
pppoe-client dial-pool-number 1
end
!
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
ppp chap hostname dsl
ppp chap password 0 dsl
end
!
HOST-2
!
interface FastEthernet0
switchport access vlan 200
no ip address
end
!
!
interface Vlan200
no ip address
pppoe enable group global
pppoe-client dial-pool-number 1
end
!
!
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
ppp chap hostname dsl
ppp chap password 0 dsl
end
!
SWITCH
SWITCH#sh cdp neighbors
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
SERVER Gig 0/1 130 R I ASR1001-X Gig 0/0/0
HOST-1 Fas 0/2 141 R B S I 887G Fas 0
HOST-2 Fas 0/1 167 R B S I 887 Fas 0
!
interface FastEthernet0/2
switchport access vlan 100
end
!
interface FastEthernet0/1
switchport access vlan 200
end
!
!
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 100,200
switchport mode trunk
end
!
PPPoE-SERVER
!
username dsl password 0 dsl
!
bba-group pppoe global
virtual-template 1
!
interface GigabitEthernet0/0/0
no ip address
negotiation auto
cdp enable
service instance 100 ethernet
encapsulation dot1q 100 etype pppoe-all
rewrite ingress tag pop 1 symmetric
bridge-domain 100
!
service instance 200 ethernet
encapsulation dot1q 200 etype pppoe-all
rewrite ingress tag pop 1 symmetric
bridge-domain 200
!
!
interface Virtual-Template1
ip unnumbered Loopback0
peer default ip address pool POOL
ppp authentication chap
!
interface BDI100
no ip address
pppoe enable group global
!
interface BDI200
no ip address
pppoe enable group global
!
interface Loopback0
ip address 192.168.10.1 255.255.255.255
end
!
ip local pool POOL 192.168.1.1 192.168.1.100
!
Alternativ können Sie "vlan-range" konfigurieren wie folgt:
!
interface GigabitEthernet0/0/0
no ip address
negotiation auto
service instance 100 ethernet
encapsulation default
bridge-domain 1
!
end
!
interface BDI1
no ip address
vlan-range dot1q 1 4094
pppoe enable group global
!
end
Netzwerkdiagramm
Überprüfen
In diesem Abschnitt überprüfen Sie, ob Ihre Konfiguration ordnungsgemäß funktioniert.
Auf HOST-1
HOST-1#show ip interface brief | exclude un
Interface IP-Address OK? Method Status Protocol
Dialer1 192.168.1.4 YES IPCP up up
HOST-1#show caller ip
Line User IP Address Local Number Remote Number <->
Vi2 SERVER 192.168.10.1 - <unknown phone in
HOST-1#ping 192.168.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
HOST-1#show ppp interface virtual-Access 2
PPP Serial Context Info
-------------------
Interface : Vi2
PPP Serial Handle: 0x1F000003
PPP Handle : 0xB2000003
SSS Handle : 0x8000004
AAA ID : 24
Access IE : 0xA7000003
SHDB Handle : 0x0
State : Up
Last State : Binding
Last Event : LocalTerm
PPP Session Info
----------------
Interface : Vi2
PPP ID : 0xB2000003
Phase : UP
Stage : Local Termination
Peer Name : SERVER
Peer Address : 192.168.10.1
Control Protocols: LCP[Open] IPCP[Open] CDPCP[Stopped]
Session ID : 3
AAA Unique ID : 24
SSS Manager ID : 0x8000004
SIP ID : 0x1F000003
PPP_IN_USE : 0x11
Vi2 LCP: [Open]
Our Negotiated Options
Vi2 LCP: MagicNumber 0x7735647E (0x05067735647E)
Peer's Negotiated Options
Vi2 LCP: MRU 1500 (0x010405DC)
Vi2 LCP: AuthProto CHAP (0x0305C22305)
Vi2 LCP: MagicNumber 0xA7A011AC (0x0506A7A011AC)
Vi2 IPCP: [Open]
Our Negotiated Options
Vi2 IPCP: Address 192.168.1.5 (0x0306C0A80105)
Peer's Negotiated Options
Vi2 IPCP: Address 192.168.10.1 (0x0306C0A80A01)
Auf HOST-2
HOST-2#show ip interface brief | exclude un
Interface IP-Address OK? Method Status Protocol
Dialer1 192.168.1.6 YES IPCP up up
HOST-2#show caller ip
Line User IP Address Local Number Remote Number <->
Vi2 SERVER 192.168.10.1 - <unknown phone in
HOST-2#ping 192.168.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
HOST-2#show ppp interface virtual-Access 2
PPP Serial Context Info
-------------------
Interface : Vi2
PPP Serial Handle: 0x7B00000A
PPP Handle : 0xA000000A
SSS Handle : 0x4C00000B
AAA ID : 68
Access IE : 0x1D00000A
SHDB Handle : 0x0
State : Up
Last State : Binding
Last Event : LocalTerm
PPP Session Info
----------------
Interface : Vi2
PPP ID : 0xA000000A
Phase : UP
Stage : Local Termination
Peer Name : SERVER
Peer Address : 192.168.10.1
Control Protocols: LCP[Open] IPCP[Open] CDPCP[Stopped]
Session ID : 10
AAA Unique ID : 68
SSS Manager ID : 0x4C00000B
SIP ID : 0x7B00000A
PPP_IN_USE : 0x11
Vi2 LCP: [Open]
Our Negotiated Options
Vi2 LCP: MagicNumber 0x421AC8AB (0x0506421AC8AB)
Peer's Negotiated Options
Vi2 LCP: MRU 1500 (0x010405DC)
Vi2 LCP: AuthProto CHAP (0x0305C22305)
Vi2 LCP: MagicNumber 0xA7A0942C (0x0506A7A0942C)
Vi2 IPCP: [Open]
Our Negotiated Options
Vi2 IPCP: Address 192.168.1.6 (0x0306C0A80106)
Peer's Negotiated Options
Vi2 IPCP: Address 192.168.10.1 (0x0306C0A80A01)
SWITCH
SWITCH#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/4, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12, Fa0/13, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/2
11 VLAN0011 active
12 VLAN0012 active
13 VLAN0013 active
100 VLAN0100 active Fa0/2
200 VLAN0200 active Fa0/1
SWITCH#Show interface trunk
Port Mode Encapsulation Status Native vlan
Gi0/1 on 802.1q trunking 1
Port Vlans allowed on trunk
Gi0/1 100,200
Port Vlans allowed and active in management domain
Gi0/1 100,200
Port Vlans in spanning tree forwarding state and not pruned
Gi0/1 100,200
Auf PPPoE-SERVER
SERVER#show caller ip
Line User IP Address Local Number Remote Number <->
Vi2.1 dsl 192.168.1.6 - - in
Vi2.2 dsl 192.168.1.5 - - in
SERVER#show ip local pool POOL
Pool Begin End Free In use
POOL 192.168.1.1 192.168.1.100 98 2
Available addresses:
192.168.1.7
192.168.1.8
192.168.1.9
.....
.....
Wenn Sie 'vlan-range' verwenden, beachten Sie die Änderung in 'Port':
SERVER#show caller ip
Line User IP Address Local Number Remote Number <->
Vi2.1 dsl 192.168.1.7 - - in
Vi2.2 dsl 192.168.1.8 - - in
Fehlerbehebung
Dieser Abschnitt enthält Informationen, die Sie zur Fehlerbehebung bei Ihrer Konfiguration verwenden können.
Diese Debug-Tools sind hilfreich, um Probleme mit PPP/PPPoE zu beheben.
- Debugging-PPP-Ereignisse
- Fehlersuche
- Debug-ppp-Aushandlung
Zugehörige Informationen
FeedbackCisco kontaktieren
- Eine Supportanfrage öffnen
- (Erfordert einen Cisco Servicevertrag)