مجموعة إخراج VCS Series أو Expressway Series Xconfig و Xstatus باستخدام PuTTY

المقدمة

يوضح هذا المستند كيفية تجميع إخراج واجهة سطر الأوامر (CLI) من أوامر xconfig وxstatus من سلسلة Video Communication Server (VCS) وأجهزة سلسلة Expressway مثل VCS-Control و VCS-Expressway و Expressway-C و Expressway-E، التي يحتاج مركز المساعدة التقنية (TAC) من Cisco من حين إلى إستردادها.

المتطلبات الأساسية

المتطلبات

توصي Cisco بأن تكون لديك معرفة بالمواضيع التالية:

• PuTTY أو برامج محاكاة طرفية مماثلة مثل SecureCRT أو Tera Term أو ما شابه.
• اسم مستخدم حساب المسؤول وكلمة المرور إلى جهاز سلسلة VCS/Expressway.
• كبل وحدة تحكم تسلسلية طراز RJ45-D-Sub9pin أو القشرة الآمنة (SSH) مسموح به في مسار الشبكة.

المكونات المستخدمة

تستند المعلومات الواردة في هذا المستند إلى إصدارات البرامج والمكونات المادية التالية:

• PuTTY (قم بزيارة صفحة تنزيل PuTTY للحصول على نسخة).
• يتم إستخدام VCS-C الذي يشغل الإصدار 7.2.1 في هذا المثال الذي يكون قابلا للتطبيق من خلال الإصدار 8.2.2، والذي يعد أحدث إصدار في الوقت الحالي.

التكوين

الاتصال حسب وحدة التحكم

ملاحظة: تفترض هذه المقالة أن لديك كبل وحدة تحكم مادية تسلسلية وظيفي متصل. يجب أن تكون قد تلقيت واحدة مع جهازك.

هنا مثال من العملية إعداد أنت ينبغي شكلت ل تسلسلي وحدة طرفية للتحكم منفذ في PuTTY.

ملاحظة: ستحتاج إلى ضبط منفذ الاتصال (COM) استنادا إلى كيفية توصيل وحدة التحكم بالكمبيوتر.

1. انتقل إلى التكوين > الفئة > الاتصال > التسلسل وضبط الإعدادات التسلسلية كما هو موضح هنا:
   
   

   

   
   
   
2. انتقل إلى الفئة > جلسة العمل، وحدد النوع التسلسلي كنوع الاتصال، وانقر فوق فتح كما هو موضح هنا:
   
   

   

الاتصال عبر SSH

هناك بديل أبسط وهو بروتوكول SSH داخل الجهاز.

1. أستخدم عنوان IP الخاص بجهاز VCS/Expressway لضبط الإعدادات في PuTTY كما هو موضح في هذا المثال:
   
   

   

   
   
   
2. قبل أو أثناء جلسة PuTTY الخاصة بك إلى جهازك، يجب عليك تعيين إعدادات التسجيل. للقيام بذلك، انتقل إلى التكوين > الفئة > جلسة العمل > التسجيل، ثم قم بتكوين الإعدادات لمطابقة هذا المثال (قم بضبط مسار الملف واسم الملف لتناسب جهاز الكمبيوتر الخاص بك واحتياجاتك):
   
   

   

   
   
   
3. وبمجرد الاتصال وتسجيل الدخول، تظهر شاشة مماثلة لهذه الشاشة. قم بتسجيل الدخول كمسؤول كما هو موضح هنا.
   
   

   

   
   
   

   تحذير: لأن هذه بيئة معملية، يمكن تجاهل التنبيهات. وإذا شوهد الإنذارات في بيئة إنتاج، ينبغي معالجتها في أقرب وقت ممكن.

   
   
   
4. اكتب الأمر xstatus ثم اضغط على مفتاح Enter:
   
   

   

   
   
   فيما يلي مخرجات xstatus التي تظهر بعد أن تقوم بضغط Enter. تم تمرير الإخراج قبل عرضه بسرعة كبيرة حتى النهاية. طالما تم تكوين التسجيل مسبقا، فسيكون ذلك في الملف النصي.
   
   

   

   
   
   الآن بعد أن قمت بتجميع إخراج الأمر xconfig، فأنت جاهز لجمع إخراج الأمر xconfig.
   
   
5. اكتب الأمر xconfig واضغط enter.
   
   
   

   

   
   
   هنا مثال على إخراج xconfig بعد الضغط على enter. تم تمرير الإخراج قبل عرضه بسرعة كبيرة حتى النهاية. طالما تم تكوين التسجيل مسبقا، فسيكون ذلك في الملف النصي.
   
   
   

   

VCS و Expressway Series x8.2

في إصدار البرنامج x8.2، يتم الآن تضمين xconfiguration وxstatus عند أخذ سجل تشخيص.

1. انتقل إلى الصيانة > التشخيصات > التسجيل التشخيصي.
   
   
2. حدد بدء سجل جديد ثم إيقاف التسجيل فورا.
   
   

   ملاحظة: تحتوي هذه الطريقة أيضا على loggingsnapshot.txt الذي يقوم بتسجيل الرسائل إستجابة للأنشطة التي تحدث على سلسلة VCS أو Expressway في ذلك الوقت.

   
   
   يحتوي أرشيف سجل التشخيص الذي تم تنزيله على هذه الملفات:
   
   
   • loggingsnapshot.txt - يحتوي على رسائل سجل إستجابة للأنشطة التي تم تنفيذها أثناء فترة التسجيل.
     
     
   • xconf_dump.txt - يحتوي على معلومات حول تكوين النظام في الوقت الذي تم فيه بدء التسجيل.
     
     
   • xstat_dump.txt - يحتوي على معلومات حول حالة النظام في وقت بدء التسجيل.
     
     
   • (إن كان ذو صلة) diagnostic_logging_tcpdump.pcap - يحتوي على الحزم التي تم الاستيلاء عليها أثناء فترة التسجيل.
     
     

التحقق من الصحة

هنا مثال على ما يبدو عليه إخراج xstatus وxconfig في الملف النصي المحفوظ مع إعدادات التسجيل:

xstatus

*s SystemUnit:
     Product: "TANDBERG VCS"
     Uptime: 24963390
     SystemTime: "2014-06-19 14:58:59"
     TimeZone: "US/Eastern"
     LocalTime: "2014-06-19 10:58:59"
     Software:
       Version: "X7.2.1"
       Build: "296181"
       Name: "s42700"
       ReleaseDate: "2012-09-25"
       ReleaseKey: "****************"
       Configuration:
         NonTraversalCalls: 500
         TraversalCalls: 200
         Registrations: 2500
         Expressway: False
         Encryption: True
         Interworking: True
         FindMe: True
         DeviceProvisioning: True
         DualNetworkInterfaces: False
         AdvancedAccountSecurity: False
         StarterPack: False
         EnhancedOCSCollaboration: True
     Hardware:
       Version: "VMWare"
       SerialNumber: "********"
*s/end

*s Ethernet 1:
     MacAddress: "00:50:56:A1:70:06"
     Speed: 10000full
     IPv4:
       Address: "10.10.10.10"
       SubnetMask: "255.255.255.0"
*s/end

*s Ethernet 2:
     MacAddress: "00:50:56:A1:70:04"
     Speed: 10000full
     IPv4:
       Address: "192.168.0.100"
       SubnetMask: "255.255.255.0"
*s/end

*s Options:
     Option 1:
       Key: "116341X300-1-!!!!!!!!"
       Description: "300 Non-traversal Calls"
     Option 2:
       Key: "116341P00-1-!!!!!!!!"
       Description: "Device Provisioning"
     Option 3:
       Key: "116341G00-1-!!!!!!!!!"
       Description: "H323-SIP Interworking Gateway"
     Option 4:
       Key: "116341U00-1-!!!!!!!!!"
       Description: "FindMe"
     Option 5:
       Key: "116341C00-1-!!!!!!!!!"
       Description: "Enhanced OCS Collaboration"
     Option 8:
       Key: "116341Y200-1-!!!!!!!!"
       Description: "200 Traversal Calls"
     Option 9:
       Key: "116341X200-1-!!!!!!!!"
       Description: "200 Non-traversal Calls"
*s/end

*s IP:
     Protocol: IPv4
     IPv4:
       Gateway: "10.10.10.1"
*s/end

*s ExternalManager:
     Status: Active
     Address: "10.10.10.104"
     Protocol: HTTP
     URL: "tms/public/external/management/systemmanagementservice.asmx"
*s/end

*s Feedback 1:
     Status: Off
*s/end

*s Feedback 2:
     Status: Off
*s/end

*s Feedback 3:
     Status: On
     URL: "http://10.10.10.104/tms/public/feedback/code.aspx"
     Expression: "/Event/CallDisconnected"
     Expression: "/Event/CallConnected"
     Expression: "/Event/CallFailure"
     Expression: "/Event/RegistrationAdded"
     Expression: "/Event/RegistrationChanged"
     Expression: "/Event/ResourceUsage"
     Expression: "/Event/AuthenticationFailure"
     Expression: "/Status/Warnings"
*s/end

*s ResourceUsage:
     Calls:
       Traversal:
         Current: 0
         Max: 0
         Total: 0
       NonTraversal:
         Current: 0
         Max: 1
         Total: 2
     Registrations:
       Current: 0
       Max: 3
       Total: 42
*s/end

*s Calls: /
*s/end

*s Zones:
     DefaultZone:
       Name: "DefaultZone"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     LocalZone:
       DefaultSubZone:
         Name: "DefaultSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
       TraversalSubZone:
         Name: "TraversalSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
       ClusterSubZone:
         Name: "ClusterSubZone"
         Bandwidth:
           LocalUsage: 0
           ClusterUsage: 0
     Searches:
       Current: 0
       CurrentDirected: 0
       Total: 64081
       Dropped: 0
       MaxSubSearchExceeded: 0
       MaxTargetsExceeded: 0
     Zone 1:
       Name: "TraversalZone"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
       Status: Active
       Type: TraversalClient
       TraversalClient:
         Peer 1:
           H323:
             Status: Active
             Address: "10.10.10.102"
             Port: 6001
             LastStatusChange: "2014-04-03 09:50:35"
           SIP:
             Status: Active
             Address: "10.10.10.102"
             Port: 7001
             LastStatusChange: "2014-04-03 09:49:13"
             Server: "TANDBERG/4102 (X7.0)"
*s/end

*s Alternates: /
*s/end

*s Links:
     Link 1:
       Name: "DefaultSZtoTraversalSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 2:
       Name: "DefaultSZtoDefaultZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 3:
       Name: "DefaultSZtoClusterSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 4:
       Name: "TraversalSZtoDefaultZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
     Link 5:
       Name: "Zone001ToTraversalSZ"
       Bandwidth:
         LocalUsage: 0
         ClusterUsage: 0
*s/end

*s Pipes: /
*s/end

*s Registrations: /
*s/end

*s SIP:
     Ethernet 1:
       IPv4:
         UDP:
           Status: Inactive
         TCP:
           Status: Active
           Address: "10.10.10.10:5060"
         TLS:
           Status: Active
           Address: "10.10.10.10:5061"
       IPv6:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
     Ethernet 2:
       IPv4:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
       IPv6:
         UDP:
           Status: Inactive
         TCP:
           Status: Inactive
         TLS:
           Status: Inactive
     Transport:
       Server 19857:
         Socket:
           Type: "SERV_UDP"
           State: "INUSE"
           ID:
             Local: 85393
             Global: 0
           Buffer:
             Input:
               Length: 20000
             Output:
               Length: 20000
         Local:
           Address: "127.0.0.1:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19856:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 150928
             Global: 1
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "127.0.0.1:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19855:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 216463
             Global: 2
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "127.0.0.1:5061"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19854:
         Socket:
           Type: "SERV_UDP"
           State: "INUSE"
           ID:
             Local: 281998
             Global: 3
           Buffer:
             Input:
               Length: 20000
             Output:
               Length: 20000
         Local:
           Address: "[::1]:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19853:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 347533
             Global: 4
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "[::1]:5060"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19852:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 413068
             Global: 5
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "[::1]:5061"
         Remote:
           Address: ""
         Network:
           Number: 1
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19851:
         Socket:
           Type: "SERV_TCP"
           State: "INUSE"
           ID:
             Local: 478603
             Global: 6
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "10.10.10.10:5060"
         Remote:
           Address: ""
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: False
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Server 19850:
         Socket:
           Type: "SERV_TLS"
           State: "INUSE"
           ID:
             Local: 544138
             Global: 7
           Buffer:
             Input:
               Length: 0
             Output:
               Length: 0
         Local:
           Address: "10.10.10.10:5061"
         Remote:
           Address: ""
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: ""
         Last:
           Packet:
             Received: 0
         Close:
           In: 20
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 0
           Add:
             Failures: 0
         Flow:
           Token: ""
       Client 7747:
         Socket:
           Type: "TLS_OUTG"
           State: "INUSE"
           ID:
             Local: 825433667
             Global: 654
           Buffer:
             Input:
               Length: 5120
             Output:
               Length: 20000
         Local:
           Address: "10.10.10.10:27573"
         Remote:
           Address: "10.10.10.102:7001"
         Network:
           Number: 2
         Certificate:
           Subject:
             Name: ""
         TLS:
           Cipher:
             Name: "DHE-RSA-AES256-SHA"
         Last:
           Packet:
             Received: -1798628722
         Close:
           In: 900
         Secure: True
         X509:
           Certificate:
             Verified: False
         Queue:
           Max:
             Size: 1
           Add:
             Failures: 0
         Flow:
           Token: ""
*s/end

*s H323:
     Registration:
       Status: Active
       IPv4:
         Address: "10.10.10.10:1719"
     CallSignaling:
       Status: Active
       IPv4:
         Address: "10.10.10.10:1720"
     Assent:
       CallSignaling:
         Status: Inactive
     H46018:
       CallSignaling:
         Status: Inactive
*s/end

*s Applications:
     Presence:
       UserAgent:
         Status: Inactive
         Presentity:
           Count: 0
       Server:
         Subscriptions:
           Count: 0
           Max: 0
           Expired: 0
           Subscribers:
             Count: 0
             Max: 0
         Status: Inactive
         Presentities:
           Count: 0
           Max: 0
         Publications:
           Presentities:
             Count: 0
             Max: 0
     ConferenceFactory:
       Status: Inactive
       NextAlias: ""
     External 1:
       Status:
         ClusterStatus:
           ClusterState: "Disabled"
       LastUpdate:
         Time: "Time not set"
         SecondsSinceLastRefresh: "1403189939"
*s/end

*s FindMeManager: /
*s/end

*s TURN:
     Server:
       Status: Inactive
*s/end

*s Policy: /
*s/end

OK






























xcommand xconfig
*c xConfiguration Login Remote Protocol: LDAP
*c xConfiguration Login Remote LDAP Server Address: ""
*c xConfiguration Login Remote LDAP Server FQDNResolution: AddressRecord
*c xConfiguration Login Remote LDAP Server Port: 389
*c xConfiguration Login Remote LDAP VCS BindUsername: ""
*c xConfiguration Login Remote LDAP VCS BindPassword: "{cipher}XXXXXXXXXX
XXXXXXXXXXXX"
*c xConfiguration Login Remote LDAP VCS BindDN: ""
*c xConfiguration Login Remote LDAP BaseDN Accounts: ""
*c xConfiguration Login Remote LDAP BaseDN Groups: ""
*c xConfiguration Login Remote LDAP Encryption: Off
*c xConfiguration Login Remote LDAP SASL: DIGEST-MD5
*c xConfiguration Login Remote LDAP CRLCheck: None
*c xConfiguration Login Remote LDAP DirectoryType: ActiveDirectory
*c xConfiguration SystemUnit Name: "VCS1-Control"
*c xConfiguration SystemUnit Maintenance Mode: Off
*c xConfiguration Option 1 Key: "116341X300-1-!!!!!!!!"
*c xConfiguration Option 2 Key: "116341P00-1-!!!!!!!!"
*c xConfiguration Option 3 Key: "116341G00-1-!!!!!!!!!"
*c xConfiguration Option 4 Key: "116341U00-1-!!!!!!!!!"
*c xConfiguration Option 5 Key: "116341C00-1-!!!!!!!!"
*c xConfiguration Option 8 Key: "116341Y200-1-!!!!!!!!"
*c xConfiguration Option 9 Key: "116341X200-1-!!!!!!!!"
*c xConfiguration Ethernet 1 Speed: Auto
*c xConfiguration Ethernet 1 IP V4 Address: "10.10.10.10"
*c xConfiguration Ethernet 1 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 1 IP V6 Address: ""
*c xConfiguration Ethernet 2 Speed: Auto
*c xConfiguration Ethernet 2 IP V4 Address: "192.168.0.100"
*c xConfiguration Ethernet 2 IP V4 SubnetMask: "255.255.255.0"
*c xConfiguration Ethernet 2 IP V6 Address: ""
*c xConfiguration IPProtocol: IPv4
*c xConfiguration IP Gateway: "10.10.10.1"
*c xConfiguration IP QoS Mode: None
*c xConfiguration IP QoS Value: 0
*c xConfiguration IP V6 Gateway: ""
*c xConfiguration IP DNS Domain Name: "######.local"
*c xConfiguration IP DNS Hostname: "VCS1-Control"
*c xConfiguration IP Ephemeral PortRange Start: 40000
*c xConfiguration IP Ephemeral PortRange End: 49999
*c xConfiguration IP RFC4821 Mode: Disabled
*c xConfiguration Administration Telnet Mode: Off
*c xConfiguration Administration SSH Mode: On
*c xConfiguration Administration HTTP Mode: On
*c xConfiguration Administration HTTPS Mode: On
*c xConfiguration Administration LCDPanel Mode: On
*c xConfiguration ExternalManager Address: "10.10.10.104"
*c xConfiguration ExternalManager Path: "tms/public/external/management/system
managementservice.asmx"
*c xConfiguration ExternalManager Protocol: HTTP
*c xConfiguration ExternalManager Server Certificate Verification Mode: On
*c xConfiguration Registration RestrictionPolicy Mode: None
*c xConfiguration Registration RestrictionPolicy Service Protocol: HTTP
*c xConfiguration Registration RestrictionPolicy Service TLS Verify Mode: On
*c xConfiguration Registration RestrictionPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Registration RestrictionPolicy Service Server 1 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 2 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Server 3 Address: ""
*c xConfiguration Registration RestrictionPolicy Service Path: ""
*c xConfiguration Registration RestrictionPolicy Service Status Path: "status"
*c xConfiguration Registration RestrictionPolicy Service UserName: ""
*c xConfiguration Registration RestrictionPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Registration RestrictionPolicy Service DefaultCPL: "<reject 
status='504' reason='Registration Policy Unavailable'/>"
*c xConfiguration Alternates ConfigurationMaster: 1
*c xConfiguration Alternates Cluster Name: ""
*c xConfiguration Alternates Peer 1 Address: ""
*c xConfiguration Alternates Peer 2 Address: ""
*c xConfiguration Alternates Peer 3 Address: ""
*c xConfiguration Alternates Peer 4 Address: ""
*c xConfiguration Alternates Peer 5 Address: ""
*c xConfiguration Alternates Peer 6 Address: ""
*c xConfiguration Transform 1 Description: "Transform destination aliases to 
URI format"
*c xConfiguration Transform 1 State: Enabled
*c xConfiguration Transform 1 Priority: 1
*c xConfiguration Transform 1 Pattern String: "([^@]*)"
*c xConfiguration Transform 1 Pattern Type: Regex
*c xConfiguration Transform 1 Pattern Behavior: Replace
*c xConfiguration Transform 1 Pattern Replace: "\1@#####.local"
*c xConfiguration Call Loop Detection Mode: On
*c xConfiguration Call Routed Mode: Always
*c xConfiguration Call Services CallsToUnknownIPAddresses: Indirect
*c xConfiguration Call Services Fallback Alias: ""
*c xConfiguration H323 Mode: On
*c xConfiguration H323 Gatekeeper Registration UDP Port: 1719
*c xConfiguration H323 Gatekeeper Registration ConflictMode: Reject
*c xConfiguration H323 Gatekeeper CallSignaling TCP Port: 1720
*c xConfiguration H323 Gatekeeper CallSignaling PortRange Start: 15000
*c xConfiguration H323 Gatekeeper CallSignaling PortRange End: 19999
*c xConfiguration H323 Gatekeeper TimeToLive: 1800
*c xConfiguration H323 Gatekeeper CallTimeToLive: 120
*c xConfiguration H323 Gatekeeper AutoDiscovery Mode: On
*c xConfiguration H323 Gateway CallerId: ExcludePrefix
*c xConfiguration SIP Mode: On
*c xConfiguration SIP Domains Domain 1 Name: "######.com"
*c xConfiguration SIP Domains Domain 2 Name: "######.local"
*c xConfiguration SIP Routes Route 1 Method: "SUBSCRIBE"
*c xConfiguration SIP Routes Route 1 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 1 Header Name: "Event"
*c xConfiguration SIP Routes Route 1 Header Pattern: "(ua-profile|phonebook).*"
*c xConfiguration SIP Routes Route 1 Authenticated: Off
*c xConfiguration SIP Routes Route 1 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 1 Port: 22400
*c xConfiguration SIP Routes Route 1 Transport: TCP
*c xConfiguration SIP Routes Route 1 Tag: "Provisioning"
*c xConfiguration SIP Routes Route 2 Method: "INFO"
*c xConfiguration SIP Routes Route 2 Request Line Pattern: ".*@(%localdomains%|
%ip%)"
*c xConfiguration SIP Routes Route 2 Header Name: "Content-Type"
*c xConfiguration SIP Routes Route 2 Header Pattern: "application/tandberg-
phonebook\+xml"
*c xConfiguration SIP Routes Route 2 Authenticated: Off
*c xConfiguration SIP Routes Route 2 Address: "127.0.0.1"
*c xConfiguration SIP Routes Route 2 Port: 22400
*c xConfiguration SIP Routes Route 2 Transport: TCP
*c xConfiguration SIP Routes Route 2 Tag: "Phonebook"
*c xConfiguration SIP Registration Standard Refresh Strategy: Maximum
*c xConfiguration SIP Registration Standard Refresh Minimum: 45
*c xConfiguration SIP Registration Standard Refresh Maximum: 60
*c xConfiguration SIP Registration Outbound Refresh Strategy: Variable
*c xConfiguration SIP Registration Outbound Refresh Minimum: 300
*c xConfiguration SIP Registration Outbound Refresh Maximum: 3600
*c xConfiguration SIP Registration Outbound Flow Timer: 0
*c xConfiguration SIP Registration Proxy Mode: Off
*c xConfiguration SIP Registration Call Remove: No
*c xConfiguration SIP Session Refresh Value: 1800
*c xConfiguration SIP Session Refresh Minimum: 500
*c xConfiguration SIP UDP Mode: Off
*c xConfiguration SIP UDP Port: 5060
*c xConfiguration SIP TCP Mode: On
*c xConfiguration SIP TCP Port: 5060
*c xConfiguration SIP TCP Outbound Port Start: 25000
*c xConfiguration SIP TCP Outbound Port End: 29999
*c xConfiguration SIP TLS Mode: On
*c xConfiguration SIP TLS Port: 5061
*c xConfiguration SIP TLS Certificate Revocation Checking Mode: Off
*c xConfiguration SIP TLS Certificate Revocation Checking OCSP Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking CRL Network Fetch 
Mode: On
*c xConfiguration SIP TLS Certificate Revocation Checking Source Inaccessibility
 Behavior: Fail
*c xConfiguration SIP Require UDP BFCP Mode: On
*c xConfiguration SIP Require Duo Video Mode: On
*c xConfiguration SIP Authentication Retry Limit: 3
*c xConfiguration SIP Authentication NTLM Mode: Auto
*c xConfiguration SIP Authentication NTLM SA Lifetime: 28800
*c xConfiguration SIP Authentication NTLM SA Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce ExpireDelta: 300
*c xConfiguration SIP Authentication Digest Nonce Maximum Use Count: 128
*c xConfiguration SIP Authentication Digest Nonce Limit: 10000
*c xConfiguration SIP Authentication Digest Nonce Length: 60
*c xConfiguration SIP GRUU Mode: On
*c xConfiguration SIP MediaRouting ICE Mode: Off
*c xConfiguration Interworking Mode: RegisteredOnly
*c xConfiguration Interworking Encryption Mode: Auto
*c xConfiguration Interworking Encryption Replay Protection Mode: Off
*c xConfiguration Interworking BFCP Compatibility Mode: Auto
*c xConfiguration Interworking Require Invite Header Mode: On
*c xConfiguration Traversal Media Port Start: 50000
*c xConfiguration Traversal Media Port End: 52399
*c xConfiguration Authentication UserName: ""
*c xConfiguration Authentication Password: "{cipher}XXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Authentication LDAP AliasOrigin: LDAP
*c xConfiguration Authentication ADS ADDomain: ""
*c xConfiguration Authentication ADS Workgroup: ""
*c xConfiguration Authentication ADS MachinePassword Refresh: On
*c xConfiguration Authentication ADS SPNEGO: Enabled
*c xConfiguration Authentication ADS SecureChannel: Auto
*c xConfiguration Authentication ADS Encryption: TLS
*c xConfiguration Authentication ADS Mode: Off
*c xConfiguration Authentication ADS Clockskew: 300
*c xConfiguration Zones Policy Mode: SearchRules
*c xConfiguration Zones Policy SearchRules Rule 1 Name: "Local zone ? no domain"
*c xConfiguration Zones Policy SearchRules Rule 1 Description: "Search local 
zone for H.323 devices (strip domain)"
*c xConfiguration Zones Policy SearchRules Rule 1 Priority: 48
*c xConfiguration Zones Policy SearchRules Rule 1 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 1 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 1 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Behavior: Replace
*c xConfiguration Zones Policy SearchRules Rule 1 Pattern Replace: "\1"
*c xConfiguration Zones Policy SearchRules Rule 1 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 1 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 1 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 1 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 2 Name: "Local zone ? full URI"
*c xConfiguration Zones Policy SearchRules Rule 2 Description: "Search local 
zone for SIP and H.323 devices with a domain"
*c xConfiguration Zones Policy SearchRules Rule 2 Priority: 51
*c xConfiguration Zones Policy SearchRules Rule 2 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 2 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 2 Mode: AliasPatternMatch
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Type: Regex
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern String: "(.+)
@######.local.*"
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Behavior: Leave
*c xConfiguration Zones Policy SearchRules Rule 2 Pattern Replace: ""
*c xConfiguration Zones Policy SearchRules Rule 2 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 2 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 2 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 2 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 3 Name: "Traversal zone search rule"
*c xConfiguration Zones Policy SearchRules Rule 3 Description: "Search traversal 
zone (Cisco VCS Expressway)"
*c xConfiguration Zones Policy SearchRules Rule 3 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 3 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 3 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 3 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 3 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 3 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 3 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 3 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 4 Name: "External IP address 
search rule"
*c xConfiguration Zones Policy SearchRules Rule 4 Description: "Route external 
IP address"
*c xConfiguration Zones Policy SearchRules Rule 4 Priority: 100
*c xConfiguration Zones Policy SearchRules Rule 4 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 4 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 4 Mode: AnyIPAddress
*c xConfiguration Zones Policy SearchRules Rule 4 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 4 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 4 Target Name: "TraversalZone"
*c xConfiguration Zones Policy SearchRules Rule 4 State: Enabled
*c xConfiguration Zones Policy SearchRules Rule 5 Name: "LocalZoneMatch"
*c xConfiguration Zones Policy SearchRules Rule 5 Description: "Default rule: 
queries the Local Zone for any alias"
*c xConfiguration Zones Policy SearchRules Rule 5 Priority: 50
*c xConfiguration Zones Policy SearchRules Rule 5 Protocol: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Source Mode: Any
*c xConfiguration Zones Policy SearchRules Rule 5 Authentication: No
*c xConfiguration Zones Policy SearchRules Rule 5 Mode: AnyAlias
*c xConfiguration Zones Policy SearchRules Rule 5 Progress: Continue
*c xConfiguration Zones Policy SearchRules Rule 5 Target Type: Zone
*c xConfiguration Zones Policy SearchRules Rule 5 Target Name: "LocalZone"
*c xConfiguration Zones Policy SearchRules Rule 5 State: Enabled
*c xConfiguration Zones DefaultZone Authentication Mode: DoNotCheckCredentials
*c xConfiguration Zones DefaultZone SIP Record Route Address Type: IP
*c xConfiguration Zones DefaultZone SIP TLS Verify Mode: Off
*c xConfiguration Zones DefaultZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone SIP Media Encryption Mode: Auto
*c xConfiguration Zones LocalZone DefaultSubZone Authentication Mode: 
DoNotCheckCredentials
*c xConfiguration Zones LocalZone DefaultSubZone Registrations: Allow
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Inter Mode:
Unlimited
*c xConfiguration Zones LocalZone DefaultSubZone Bandwidth PerCall Intra Mode:
Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth Total Mode: Unlimited
*c xConfiguration Zones LocalZone TraversalSubZone Bandwidth PerCall Mode:
Unlimited
*c xConfiguration Zones LocalZone SIP Record Route Address Type: IP
*c xConfiguration Zones Zone 1 Name: "TraversalZone"
*c xConfiguration Zones Zone 1 HopCount: 15
*c xConfiguration Zones Zone 1 H323 Mode: On
*c xConfiguration Zones Zone 1 SIP Mode: On
*c xConfiguration Zones Zone 1 Type: TraversalClient
*c xConfiguration Zones Zone 1 TraversalClient Authentication Mode: DoNot
CheckCredentials
*c xConfiguration Zones Zone 1 TraversalClient Authentication UserName: 
"######auth"
*c xConfiguration Zones Zone 1 TraversalClient Authentication Password: 
"{cipher}XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Zones Zone 1 TraversalClient Registrations: Allow
*c xConfiguration Zones Zone 1 TraversalClient H323 Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient H323 Port: 6001
*c xConfiguration Zones Zone 1 TraversalClient SIP Protocol: Assent
*c xConfiguration Zones Zone 1 TraversalClient SIP Port: 7001
*c xConfiguration Zones Zone 1 TraversalClient SIP Transport: TLS
*c xConfiguration Zones Zone 1 TraversalClient SIP TLS Verify Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Poison Mode: Off
*c xConfiguration Zones Zone 1 TraversalClient SIP Media Encryption Mode: Auto
*c xConfiguration Zones Zone 1 TraversalClient RetryInterval: 120
*c xConfiguration Zones Zone 1 TraversalClient Peer 1 Address: "10.10.10.102"
*c xConfiguration Zones Zone 1 TraversalClient Peer 2 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 3 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 4 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 5 Address: ""
*c xConfiguration Zones Zone 1 TraversalClient Peer 6 Address: ""
*c xConfiguration Bandwidth Default: 384
*c xConfiguration Bandwidth Downspeed PerCall Mode: On
*c xConfiguration Bandwidth Downspeed Total Mode: On
*c xConfiguration Bandwidth Link 1 Name: "DefaultSZtoTraversalSZ"
*c xConfiguration Bandwidth Link 1 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 1 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 1 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 1 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 2 Name: "DefaultSZtoDefaultZ"
*c xConfiguration Bandwidth Link 2 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 2 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 2 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 2 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 3 Name: "DefaultSZtoClusterSZ"
*c xConfiguration Bandwidth Link 3 Node1 Name: "DefaultSubZone"
*c xConfiguration Bandwidth Link 3 Node2 Name: "ClusterSubZone"
*c xConfiguration Bandwidth Link 3 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 3 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 4 Name: "TraversalSZtoDefaultZ"
*c xConfiguration Bandwidth Link 4 Node1 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 4 Node2 Name: "DefaultZone"
*c xConfiguration Bandwidth Link 4 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 4 Pipe2 Name: ""
*c xConfiguration Bandwidth Link 5 Name: "Zone001ToTraversalSZ"
*c xConfiguration Bandwidth Link 5 Node1 Name: "TraversalZone"
*c xConfiguration Bandwidth Link 5 Node2 Name: "TraversalSubZone"
*c xConfiguration Bandwidth Link 5 Pipe1 Name: ""
*c xConfiguration Bandwidth Link 5 Pipe2 Name: ""
*c xConfiguration Policy AdministratorPolicy Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Protocol: HTTP
*c xConfiguration Policy AdministratorPolicy Service TLS Verify Mode: On
*c xConfiguration Policy AdministratorPolicy Service TLS CRLCheck Mode: Off
*c xConfiguration Policy AdministratorPolicy Service Server 1 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 2 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Server 3 Address: ""
*c xConfiguration Policy AdministratorPolicy Service Path: ""
*c xConfiguration Policy AdministratorPolicy Service Status Path: "status"
*c xConfiguration Policy AdministratorPolicy Service UserName: ""
*c xConfiguration Policy AdministratorPolicy Service Password: "{cipher}
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX"
*c xConfiguration Policy AdministratorPolicy Service DefaultCPL: "<reject
 status='504' reason='Admin Policy Unavailable'/>"
*c xConfiguration Policy FindMe Mode: Off
*c xConfiguration Policy FindMe CallerId: IncomingID
*c xConfiguration Policy FindMe UserDeviceRestriction: Off
*c xConfiguration Applications ConferenceFactory Mode: Off
*c xConfiguration Applications ConferenceFactory Alias: ""
*c xConfiguration Applications ConferenceFactory Template: ""
*c xConfiguration Applications ConferenceFactory Range Start: 1
*c xConfiguration Applications ConferenceFactory Range End: 65535
*c xConfiguration Applications OCS Relay Mode: Off
*c xConfiguration Applications OCS Relay OCS Domain: ""
*c xConfiguration Applications OCS Relay OCS Routing Prefix: "ocs"
*c xConfiguration Applications Presence Server Mode: Off
*c xConfiguration Applications Presence Server Publication ExpireDelta: 1800
*c xConfiguration Applications Presence Server Subscription ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent Mode: Off
*c xConfiguration Applications Presence User Agent ExpireDelta: 3600
*c xConfiguration Applications Presence User Agent RetryDelta: 1800
*c xConfiguration Applications Presence User Agent Presentity Idle Status: Online
*c xConfiguration ResourceUsage Warning Activation Level: 90
*c xConfiguration Services AdvancedMediaGateway Zone Name: ""
*c xConfiguration Services AdvancedMediaGateway Policy Mode: Off

OK
exit
Bye!

استكشاف الأخطاء وإصلاحها

هذه هي المشاكل الثلاث الأكثر شيوعا التي قد تواجهها:

• يتم إستخدام كبل تسلسلي غير صحيح أو معيب. تأكد من إستخدام الكبل الوارد مع الجهاز.
  
  
• تظهر أحرف غير قابلة للتعرف عليها على شاشة وحدة التحكم. يشير ذلك إلى تعيين معدل الباود بشكل غير صحيح. تستند معدلات الباود إلى مضاعفات من إثنين، بحيث يمكنك مضاعفة أو خفض القيمة بمقدار النصف حسب الحاجة حتى تجد الإعداد الصحيح. في هذه الحالة، يجب أن يكون الإعداد الصحيح 115200.
  
  
• لا يمكنك الاتصال ببرنامج المحاكاة الطرفية. إلى جانب مشكلات الكابلات، تحدث هذه المشكلة عادة بسبب إحدى المشكلات التالية:
  
  
  • تحاول الاتصال عبر Telnet أو SSH ويجب عليك تغيير نوع الاتصال إلى تسلسلي عند إستخدام اتصال تسلسلي.
    
    
  • أنت على منفذ COM خاطئ. لاكتشاف منفذ COM الذي يستخدمه الكمبيوتر مع الاتصالات التسلسلية القائمة على USB، انتقل إلى لوحة التحكم > إدارة الأجهزة وانقر فوق المنافذ. من هذا الإطار، يمكنك التحقق من منفذ COM المخصص لجهاز USB التسلسلي.
    
    
  • ليس لديك برامج تشغيل لجهازك التسلسلي مثبتة. إذا كان هذا هو الحال، يجب تحديد موقعهم وتثبيتهم.
  
  
  
• يتعذر عليك إدخال SSH في الجهاز. إلى جانب مشكلات الكابلات، تحدث هذه المشكلة عادة بسبب إحدى المشكلات التالية:
  
  
  • تحاول الاتصال عبر SSH ولا يمكنك الوصول إلى الجهاز بسبب مشاكل في اتصال الشبكة. صححت الشبكة موصولية إصدار. بدلا من ذلك، قد لا يتم تمكين SSH للجهاز. أدخل الويب/HTTP/HTTPS في الجهاز وضمان تمكين الوصول إلى SSH ضمن التكوين>SystemConfiguration>خدمات الشبكة.
    
    
  • ليس لديك مفتاح Rivest-Shamir-Addleman (RSA) مخزنا مؤقتا من الجهاز. بشكل نموذجي، تتم مطالبتك بقبول مفتاح RSA. تأكد من قبول المفتاح.
    
    
  • يفشل تسجيل دخولك بسبب اسم مستخدم وكلمة مرور غير صحيحين. تأكد من إستخدام اسم المستخدم وكلمة المرور الصحيحين للجهاز.