show test

Use the show test command to display the results of diagnostic tests.

show test [mod_num]

Syntax Description

mod_num

(Optional) Number of the module. If you do not specify a number, test statistics are given for the general system as well as for module 1.

Default

This command has no default setting.

Command Mode

Normal.

Usage Guideline

The NMP only applies to module 1; therefore, only the display for module 1 includes the NMP status. If you specify other modules, the NMP status is not displayed.

Example

This example shows how to display general test results for the system and for module 1:

Console> show test
Environmental Status (. = Pass, F = Fail, U = Unknown)
  PS (3.3V):   .   PS (12V): .   PS (24V):   .   PS1: .     PS2: .
  Temperature: .   Fan:      .
Module 1 : 2-port 10/100BaseTX Supervisor
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)
  ROM:  .   Flash-EEPROM: .   Ser-EEPROM: .   NVRAM: .   MCP Comm: .
  EARL Status :
        NewLearnTest:         .
        IndexLearnTest:       .
        DontForwardTest:      .
        MonitorTest           .
        DontLearn:            .
        FlushPacket:          .
        ConditionalLearn:     .
        EarlLearnDiscard:     .
        EarlTrapTest:         .
LCP Diag Status for Module 1  (. = Pass, F = Fail, N = N/A)
 CPU         : .    Sprom    : .    Bootcsum : .    Archsum  : .
 RAM         : .    LTL      : .    CBL      : .    DPRAM    : .   SAMBA : .
 Saints      : .    Pkt Bufs : .    Repeater : N    FLASH    : .
 Phoenix     : . TrafficMeter: . UplinkSprom : . PhoenixSprom: .
  MII Status:
  Ports 1  2
  -----------
        N  N
 SAINT/SAGE Status :
  Ports 1  2
  -----------
        .  .
 PHOENIX Port Status :
  Ports 9    17   18   19   20   21   22
      INBAND A->B B->A B->C C->B A->C C->A
  ------------------------------------------
        .    .    .    .    .    .    .
 Packet Buffer Status :
  Ports 1  2
  -----------
        .  .
 PHOENIX Packet Buffer Status :
  Ports INBAND A<->B B<->C A<->C
  ------------------------------
         .     .     .     .
 Loopback Status [Reported by Module 1] :
  Ports  1  2  9
  --------------
         .  .  .
 Channel Status :
  Ports  1  2
  -----------
         .  .
Console>
  

Table 6-40 describes the fields in the show test command output.

Table 6-40: show test Command Output Fields 

Field	Description
Environmental Status	Test results that apply to the general system environment.
PS (3.3V)	Test results for the 3.3V power supply.
PS (12V)	Test results for the 12V power supply.
PS (24V)	Test results for the 24V power supply.
PS1	Test results for power supply 1.
PS2	Test results for power supply 2.
Temperature	Test results for temperature.
Fan	Test results for the fan.
Module 1	Test results that apply to module 1. The module type is indicated as well.
Network Management Processor (NMP) Status	Test results that apply to the NMP on the supervisor module.
ROM	Test results for ROM.
Flash-EEPROM	Test results for the Flash EEPROM.
Ser-EEPROM	Test results for serial EEPROM.
NVRAM	Test results for the NVRAM.
EARL Status	Fields that display the EARL status information.
NewLearnTest	Test results for NewLearn test (EARL).
IndexLearnTest	Test results for IndexLearn test (EARL).
DontForwardTest	Test results for DontForward test (EARL).
MonitorTest	Test results for Monitor test (EARL).
DontLearn	Test results for DontLearn test (EARL).
FlushPacket	Test results for FlushPacket test (EARL).
ConditionalLearn	Test results for ConditionalLearn test (EARL).
EarlLearnDiscard	Test results for EarlLearnDiscard test (EARL).
EarlTrapTest	Test results for EarlTrap test (EARL).
LCP Diag Status for Module 1	Test results for the specified module.
CPU	Test results for the CPU.
Sprom	Test results for serial PROM.
Bootcsum	Test results for Boot ROM checksum.
Archsum	Test results for archive Flash checksum.
RAM	Test results for the RAM.
LTL	Test results for local-target logic.
CBL	Test results for color-blocking logic.
DPRAM	Test results for dual-port RAM.
SAMBA	Test results for SAMBA chip.
Saints	Test results for SAINT chips.
Pkt Bufs	Test results for the packet buffers.
Repeater	Test results for repeater module.
FLASH	Test results for the Flash.
Phoenix	Test results for the Phoenix.
TrafficMeter	Test results for the TrafficMeter.
UplinkSprom	Test results for the UplinkSprom.
PhoenixSprom	Test results for the Phoenix.
MII Status	Test results for MII ports.
SAINT/SAGE Status	Test results for individual SAINT/SAGE chip.
Phoenix Port Status	Test results for Phoenix ports.
Packet Buffer Status	Test results for individual packet buffer.
Phoenix Packet Buffer Status	Test results for Phoenix packet buffer.
Loopback Status	Test results for the loopback test.
Channel Status	Test results for the channel test.

This example shows how to display test results for module 10 (an FDDI module):

Console> show test 10
Module 10 : 2-port MM MIC FDDI
Module 10 : FDDI Module Status: (. = Pass, F = Fail, U = Unknown)
FDDI Control Processor (FCP) Status:
  ROM:  .   RAM:  .   Flash-EEPROM: .   Dpram: .
  Switch Memory Status:
  RAM:  .   Cache-SRAM: .    DmpCom: .    Loadgen: .
FDDI Status:
  Port A Access:   .  Port B Access:   .
  Port A Loopback: .  Port B Loopback: .
  MAC Access:      .  MAC Buffer R/W:  .
  MAC Internal LB: .  MAC External LB: .
  CAM:  . . . .
Data Movement Processor (DMP) Status:
  Flash-EEPROM: .   RAM: .  SRAM: . COMM: .
  Switch Memory Status:
  RAM: .  Cache-SRAM: .
FDDI Status:
  MAC Access:            .   MAC Buffer R/W:        .
  MAC Internal LB:       .   MAC External LB:       .  LoadGen:.
  FBIGA Access:          .   FBIGA->MAC Buffer R/W: .
  FBIGA->MAC TxDMA:      .   FBIGA->MAC RxDMA:      .
  FBIGA->MAC Internal LB:.   FBIGA->MAC External LB:.  LoadGen:.
Bus Interface Status:
  SBIGA Access:          .   SBIGA->SAGE RxDMA:     .  SBIGA<-SAGE TxDMA:.
  Biga Loop Access:      .   Biga Loop Rx:          .  Biga Loop Tx:     .
LCP Diag Status for Module 10  (. = Pass, F = Fail, N = N/A)
 CPU         : .    Sprom    : .    Bootcsum : .    Archsum  : N
 RAM         : .    LTL      : .    CBL      : .    DPRAM    : .   SAMBA : N
 Saints      : .    Pkt Bufs : .    Repeater : N    FLASH    : N
 SAINT/SAGE Status :
  Ports 1
  --------
        .
 Packet Buffer Status :
  Ports 1
  --------
        .
 Loopback Status :
  Ports 1
  --------
        .
Console>
  

Table 6-41 describes the fields in the show test command output for an FDDI module.

Table 6-41: show test Command Output Fields (FDDI) 

Field	Description
Module 10	Field that indicates the subsequent test results apply to module 10. The module type is indicated as well.
FDDI Control Processor (FCP) Status	Fields that indicate the FCP status.
ROM	Test results for the ROM.
RAM	Test results for the RAM.
Flash-EEPROM	Test results for the Flash EEPROM.
Dpram	Test results for the dynamic PRAM.
Switch Memory Status	Fields that indicate the switch memory status.
RAM	Test results for the RAM.
Cache-SRAM	Test results for the queue SRAM.
DmpCom	Test results for communication block.
Loadgen	Test results for MAC LoadGen test.
FDDI Status	Fields that indicate FDDI status.
Port A Access	Test results for port A PHY register test.
Port B Access	Test results for port B PHY register test.
Port A Loopback	Test results for port A PHY loopback test.
Port B Loopback	Test results for port B PHY loopback test.
MAC Access	Test results for MAC register test.
MAC Buffer R/W	Test results for MAC buffer memory test.
MAC Internal LB	Test results for MAC internal loopback test.
MAC External LB	Test results for MAC external loopback test.
CAM	Test results for the CAM.
Data Movement Processor (DMP) Status	Fields that indicate the DMP status.
Flash-EEPROM	Test results for the Flash EEPROM.
RAM	Test results for the RAM.
SRAM	Test results for the SRAM test.
COMM	Test results for communication block.
Switch Memory Status	Fields that indicate the switch memory status.
RAM	Test results for the RAM.
Cache-SRAM	Test results for the queue SRAM.
FDDI Status	Fields that indicate FDDI status.
MAC Access	Test results for MAC register test.
MAC Buffer R/W	Test results for MAC buffer memory test.
MAC Internal LB	Test results for MAC internal loopback test.
MAC External LB	Test results for MAC external loopback test.
LoadGen	Test results for MAC LoadGen test.
FBIGA Access	Test results for FBIGA register test.
FBIGA->MAC Buffer R/W	Test results for FBIGA buffer memory test.
FBIGA->MAC TxDMA	Test results for FBIGA transmit test.
FBIGA->MAC RxDMA	Test results for FBIGA receive test
FBIGA->MAC Internal LB	Test results for FBIGA internal loopback test.
FBIGA->MAC External LB	Test results for FBIGA external loopback test.
LoadGen	Test results for FBIGA LoadGen test.
Bus Interface Status	Fields that indicate bus interface status.