show config

Use the show config command to display the current system configuration.

show config

Syntax Description

This command has no arguments or keywords.

Default

This command has no default setting.

Command Type

Switch command.

Command Mode

Normal.

Example

This example shows the (partial) contents of a configuration file:

Console> show config
...
.........
.........
.........
..........
.
begin
set password $1$FMFQ$HfZR5DUszVHIRhrz4h6V70
set enablepass $1$FMFQ$HfZR5DUszVHIRhrz4h6V70
set prompt cat19-lnf>
set length 24 default
set logout 20
set banner motd ^C
Welcome to the Cat 5000! ^C
!
#system
set system baud  9600
set system modem disable
set system name  Catalyst 5000
set system location San Jose, CA
set system contact  Susan x237
!
#snmpset snmp community read-only      public
set snmp community read-write     private
set snmp community read-write-all secret
set snmp rmon disable
set snmp trap disable module
set snmp trap disable chassis
set snmp trap disable bridge
set snmp trap disable repeater
set snmp trap disable vtp
set snmp trap disable auth
set snmp trap disable ippermit
!
#ip
set interface sc0 1 172.16.25.142 255.255.0.0 172.16.255.255
set interface sl0 0.0.0.0 0.0.0.0
set arp agingtime 1200
set ip redirect   enable
set ip unreachable   enable
set ip fragmentation enable
set ip route 0.0.0.0 172.16.1.201    1
set ip alias default         0.0.0.0
!
#Command alias
!
#vmps
set vmps tftpserver 1.1.1.1 vmps-config-database.1
set vmps state enable
!
#dns
set ip dns server 198.92.30.32 primary
set ip dns server 171.69.2.132
set ip dns enable
set ip dns domain cisco.com
!
#tacacs+
set tacacs server 171.69.195.110 primary
set tacacs attempts 3
set tacacs directedrequest disable
set tacacs timeout 5
set authentication login tacacs disable
set authentication login local enable
set authentication enable tacacs disable
set authentication enable local enable
!
#bridge
set bridge ipx snaptoether   8023raw
set bridge ipx 8022toether   8023
set bridge ipx 8023rawtofddi snap
!
#vtp
set vtp mode server
set vtp pruning disable
set vtp pruneeligible 2-1000
!
#spantree
#vlan 1
set spantree enable    1
set spantree fwddelay 15    1
set spantree hello    2     1
set spantree maxage   20    1
set spantree priority 32768 1
!
#cgmp
set cgmp enable
!
#syslog
set logging console enable
set logging server disable
set logging level cdp 2 default
set logging level cgmp 2 default
set logging level disl 5 default
set logging level dvlan 2 default
set logging level earl 2 default
set logging level fddi 2 default
set logging level ip 2 default
set logging level pruning 2 default
set logging level snmp 2 default
set logging level spantree 2 default
set logging level sys 5 default
set logging level tac 2 default
set logging level tcp 2 default
set logging level telnet 2 default
set logging level tftp 2 default
set logging level vtp 2 default
set logging level vmps 2 default
!
#ntp
set ntp broadcastclient disable
set ntp broadcastdelay 3000
set ntp client enable
set ntp server 172.16.21.83
set timezone PST -7 0
set summertime enable PSST
!
#permit list
set ip permit disable
!
#module 1 : 2-port 100BaseTX Supervisor
set module name    1
set vlan 1    1/1-2
set port enable     1/1-2
set port level      1/1-2  normal
set port duplex     1/1-2  half
set port trap       1/1-2  disable
set port name       1/1-2
set port security   1/1-2  disable
set port membership 1/1-2  static
set cdp enable   1/1-2
set cdp interval 1/1-2 60
set trunk 1/1  auto 1-1000
set trunk 1/2  auto 1-1000
set spantree portfast    1/1-2 disable
set spantree portcost    1/1-2 10
set spantree portpri     1/1-2 32
set spantree portvlanpri 1/1  0
set spantree portvlanpri 1/2  0
!
<display truncated>
end
Console>
  

Related Commands

clear config
write