hCisco Unified CallManager Release
4.1(3) Service Release 6
Release Notes Version 1
December 3, 2007
Table of Contents
These
Service Release (SR) release notes contain important information about
installation procedures and resolved caveats for Cisco Unified CallManager
release 4.1(3)SR6. Updates for these release notes occur with every Cisco
Unified CallManager SR release.
Note: Please review all sections in this document pertaining to installation before you install this Service Release. Failure to install this Service Release as described may result in inconsistent Cisco Unified CallManager behavior.
Make sure that you install and
configure this release of Cisco Unified CallManager on a Cisco Media
Convergence Server (MCS).
You must
install Cisco Unified CallManager on a Cisco-approved HP server configuration
or on a Cisco-approved IBM server configuration, as indicated here:
http://www.cisco.com/en/US/products/hw/voiceapp/ps378/prod_brochure_list.html
This Service Release is a
cumulative update that incorporates all of the fixes and changes from Cisco
Unified CallManager 4.1(3)ES126, along with additional changes that are
specific to this Service Release.
Note: Service Releases do not impact system compatibility unless specifically stated.
Cisco
provides the following guidance to help you successfully install and/or upgrade
Cisco Unified CallManager software:
·
Terminal
Services/Remote Desktop Connection is not supported to perform this upgrade.
For remote installation use VNC.
·
Always
log in with Administrator privileges before you begin the SR installation or
uninstallation process.
·
Exit
all other applications and close all Terminal Services sessions before you
begin the upgrade process.
·
To
minimize call-processing interruptions during the upgrade process, register all
devices to servers that are running the same version of Cisco Unified
CallManager software. Make sure that you register all devices to the
backup Cisco Unified CallManager server or to the primary Cisco Unified
CallManager server, but not to both the backup and primary servers.
·
Upgrade
all servers to Cisco Unified CallManager 4.1(3) and make sure that the servers
are online before you begin this SR installation; otherwise, pre-upgrade checks
may fail or return faulty information. This SR is based on Engineering Special
126. For this Service Release, Cisco supports upgrades from any Cisco Unified
CallManager 4.1(3) release up to 4.1(3)ES126.
·
If
you are using Cisco Security Agent or a supported antivirus agent, you must
DISABLE this software and then restart your system before you proceed with this
installation. You must manually re-enable these services after the installation
is complete.
·
Make
sure that you disable the following Cisco-verified platform agents and
applications; these products may interfere with the Cisco Unified CallManager
installation:
o
Server
management agents
o
VOIP
monitoring/performance monitoring
o
Remote
access/remote management agents
·
For
a list of supported platform agents (i.e. Antivirus Products, etc.), review the
following: http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_bulletin0900aecd800f8572.html
·
For optimum performance, apply the most current OS upgrade and SR
before you install the Cisco Unified CallManager SR. For more
information, refer to Cisco IP Telephony Operating System, SQL Server,
Security Updates at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/osbios.htm
·
Service Releases contain firmware loads that are current as of
posting, however, Cisco recommends that you always download the latest firmware
load from the
· All nodes in the cluster run through a database replication health check during the upgrade process as an extra measure, even though the publisher's database replication check should catch any replication errors clusterwide.
·
If you encounter a warning message on any node during
this check, make sure that you stop the installation process and check the log
files. Follow the recommendations listed below if the log file displays any of
the following messages:
o All agent-implementing jobs are waiting to start
o
At
least one agent-implementing job is attempting to execute after a previous
failure
o
At least one agent-implementing job has failed to execute
successfully
The following procedure provides
details about how to install Cisco Unified CallManager 4.1(3)SR6.
Note: Cisco recommends that you apply this Service
Release during a maintenance window.
Note: It is very important to disable platform agents and services, such as NetIQ and Prognosis performance monitoring, antivirus (such as Cisco-verified McAfee services or other Cisco-verified AV products) and intrusion detection software, remote management services, and any other monitoring applications that automatically restart services; this action ensures that your system does not encounter issues that are associated with these services.
·
This
Service Release upgrades the affected services and files and then it restarts
the server when the upgrade has completed successfully.
·
Apply
this Service Release to all of your Cisco Unified CallManager servers,
beginning with the publisher server and TFTP server.
Installation Procedure
Note: To verify that the installation completed successfully, follow the instructions in Step 4 in the Installation Instructions section.
Perform the following procedure to
install Cisco Unified CallManager 4.1(3)SR6:
1.
From
the
ciscocm.4-1-3-sr6.exe file;
then, follow the instructions to download the file.
2.
Transfer
the file to each CallManager node in the cluster.
3.
Double-click
the ciscocm.4-1-3-sr6.exe executable file to begin the installation as
noted below:
4.
Cisco
recommends that you upgrade all servers in the cluster sequentially, to the
same version of Cisco Unified CallManager software; otherwise call-processing
interruptions may occur:
a.
Begin
with the publisher server
b.
Followed
by the TFTP server
c.
Followed
by the sequential upgrade of the backup servers
d.
Finally,
the sequential upgrade of the primary servers
5.
Click
Next when the installation process displays a message that asks if you
want to install this SR.
The remainder of the installation process
continues without any additional user input. The system displays a message when
the installation is complete.
6.
Verify
that the installation completed successfully by taking the following actions:
a.
Click
Yes when the system prompts you to view the log file.
b.
Scroll
down to the end of the log file; if errors occurred during the installation,
the errors section at the bottom of the log file will be updated with a
corresponding severity.
7.
If
any of the Client Plugins have a lower version than those included in this SR,
perform the following:
After you have rebooted the server and completed the
upgrade on all servers in the cluster, go to Cisco Unified CallManager
Administration on any client machines (i.e. JTAPI, RTMT Client, etc.), navigate
to the Application > Install Plugins menu. Choose the applicable
plug-in, run the program from its current location, and follow the installation
instructions that the system displays.
8.
The
system may create or edit the following log files during the installation or
uninstallation process:
·
c:\program
files\common files\cisco\logs\CCMPatch\Cisco CallManager 4.1(3)SR6 Installation
YYYY-MM-DD HH.mm.log (this file is also accessible by navigating to the Start
menu shortcut "Cisco Install Logs" under the CCMPatch folder)
·
c:\install\dbinstall\dbinstallXXX.txt
·
c:\program
files\common files\cisco\logs\CCMPatch\sqlX.txt
·
c:\program
files\common files\cisco\logs\history.log
Note: This Service Release can take up to 20 minutes to complete the installation.
The following
procedure provides details about how to uninstall Cisco Unified CallManager
4.1(3)SR6. (The SR uninstallation process does not change the device
defaults to the version that was installed before the SR.)
Note: Uninstall the SR on all servers in the cluster in the same order in which you performed the installation.
Perform the following
procedure to uninstall Cisco Unified CallManager 4.1(3)SR6:
1. Navigate to Start > Settings > Control Panel > Add/Remove Programs > Cisco Unified CallManager 4.1(3)SR6 Uninstall.
A dialog box displays to confirm that you
want to uninstall this SR.
2. Click Next and then Yes to continue.
3. Verify that the uninstallation process completed successfully by taking the following actions:
a. Click Yes when the system prompts you to
view the log file.
b. Scroll down to the end of the log file; if errors
occurred during the installation, the errors section at the bottom of the log
file will be updated with a corresponding severity.
4. After you have rebooted the server and completed the uninstall on all servers in the cluster, you need to revert to the prior version of the plug-in after the uninstallation is complete, navigate to the Application > Install Plugins menu from Cisco Unified CallManager Administration.
5. Choose the applicable plug-in on the client machine, run the program from its current location, and follow the uninstallation instructions that the system displays.
The system may create or edit the following log files during the
installation or uninstallation process:
·
c:\program
files\common files\cisco\logs\CCMPatch\Cisco CallManager 4.1(3)SR6 Installation
YYYY-MM-DD HH.mm.log (this file is also accessible by navigating to the Start
menu shortcut "Cisco Install Logs" under the CCMPatch folder)
·
c:\install\dbinstall\dbinstallXXX.txt
·
c:\program
files\common files\cisco\logs\CCMPatch\sqlX.txt
·
c:\program
files\common files\cisco\logs\history.log
None.
Resolved Caveats for Cisco Unified
CallManager 4.1(3)SR6
4.1(3)sr6 |
|
DST-
JRE update needed for 2008 Brazil Summertime change |
|
DST-
Comm Manager ToD update needed for 2008 Brazil Summertime change |
|
DST-
Comm Manager update needed for 2008 Brazil Summertime change |
|
DST-
Comm Manager RTMT update needed for 2008 Brazil Summertime change |
|
DST-
RTMT JVM needs new timezone data to support 2007 NZ DST changes |
|
Removing
eHook feature from 11/06, 31, 41/61 and 70/71 phone models |
|
Update
Load_ID.prm for 7937 phone |
|
WebKnight
triggered when string 'code=' is encountered |
|
Unable
to Logon to the CCMUser Page |
|
CCMUser
login takes 12 Seconds to login |
|
CCM
is not porting the OCN in Qsig ICT setup to oCdpnVM |
|
Faststart
used with CTI RP can cause mediaexchange to fail |
|
IPMA
Assistant Console plugin to be uploded for 4.1(3)SR6 |
|
Adding
TNP 8.3(3) and 7937 1.0(1) to CUCM |
|
Adding
8.3(3) features |
|
FS-
CCM doesn't send CLC after CTI call hold request |
|
Calls
from Boulder G729 communicator get fast busy due to MSD issue |
|
Forwarded
inbound QSIG calls sometimes presented as direct call to Unity |
|
Meet-Me
# Becomes Unusable After Parking It Twice |
|
busy
hunt group return incorrect release cause |
|
JTAPI
stopped delivering events |
|
Platform
excetion when adding Terminal Observer |
|
Null
pointer exception in JTAPI receive thread |
|
PlatformExceptionImpl
Error randomly occurs for redirect request |
|
External
caller DN was same as agent DN causes JTAPI to create EXT type |
|
7985
Can not disable advertisement of g.722 codec |
|
Option
for- Stop Extending Call On Q.931 Disconnect Causes |
|
Need
ability to delay media until alerting, progress, connect, or PI |
|
StartMulticastMediaReception
in CCM trace must display multicast IP |
|
Ringing
condition with CCM and BA Dailer version 7.1.3 |
|
Intermittent
Location CAC Bandwidth Leak |
|
Connected
INFO fail to update orig side when PBX Blind Xfer by Reroute |
|
Callmanager
needs to pass multiple PI in Alerting message |
|
CCM
crash caused by StationD LineStruct array resize |
|
CallManger
limits unity 5 voicemail port integration to less than 96 |
|
Backporting
IPMA Assistant Console plugin to 4.1(3)SR6 |
4.1(3)es126 |
|
No
counters in traces to indicate available resources for MTP/Xcoder |
|
CallPark
Reversion text not displayed when device controlled by CTI |
|
correct
DST settings for |
|
Button
Disapears from IPMA ToolBar |
|
correct
DST settings for |
|
Extra
button templates are displayed for 7937 |
|
Update
the QED setting for the 7937 phone guide |
|
User
Guide added for new IP Phone 7937 |
|
CiscoAddress.setForwarding
reports invalid state 1 (= IN_SERVICE) |
|
MTP
port not closed when h323 call finishes before media creates MXs |
|
CTI
Route Points stuck in state=WaitforRegister after ccm.exe crashes |
|
H245
Process leak when not getting SDLListenRes from SDL TCP layer |
|
IPVMS
crash - race condition or memory shortage |
|
CM
strips first digit of PRI DMS Original Called Party Number |
|
CCM
service restarts on receiving a valid SIP Packet |
|
Changing
User Profile information deletes 'ciscoatuserprofile' in AD |
|
Update
English locale Files into the CCM branches for 8.3.3 release |
|
Locale
Changes |
|
7940
- 7960 Do not upgrade to P00308000700 |
|
CCM
4.1 No ACK to mid-call INVITE response |
|
Transfer
failure when operator transfers caller to ICM route point |
|
CTI
Loop causing CM CPU Spike |
|
No
CallAttributeInfoEvent after LineEventFilterChange |
|
Call
disappears from the CTIOS client on cycling CTIOS server. |
|
Phones
stuck at requesting template |
|
CM
fails to start if not in CM grp- ERROR readStationRegistrationProfile |
|
IPMA
Callback feature causes ccm.exe crash |
|
Transfers-fast
go/stop with network delay causes fast busy |
|
JATPI
does not provide Network Reached event when IVR transfers |
|
re-tag
XML file for guinness QED |
|
CDP.sys
causing nonpaged pool memory leak identified by Mdl tag |
|
CDBLException
Dump adding FXO ports into Route group |
|
EM
login/logout causes errors in event log |
|
Enter
number message keep displaying for a long time after Gpickup |
|
CCM
Does Not Populate Correct IP-Port For IRR - Cannot Send IRR Out |
|
reason=unavailable
is converted to originalCdpnRedirectReason=0 |
|
An
AXL issue when the same parameter is being modified for the multiple |
|
SIP
diversion header with reason=unavailable is not handled properly. |
|
Can't
add phone template via BAT |
|
Prefix
not prepended on the caller info after a call pickup. |
|
Called
party number contains number prefix in a scenario |
|
Call
is not cleared properly |
|
Add
Russian time zones (with DST) for GMT+4 and GMT+5 timezones |
|
SR
install reports error "2" when 2nd JRE is installed |
|
CDR
Analysis and Reporting does not reflect DST changes for |
|
Enable
Guinness Model phones to appear in CUCM Admin Pages |
|
Call
Manager Update needed for New Zealand DST changes in 2007 CSCsc29848call
processing failures due to partial table loads |
|
call
processing failures due to partial table loads |
|
CCM
Shows Conf resources allocated when CFB shows no sessions active |
|
queued
MSD from previous transfer causes later MSD failure |
|
ccm
4.1.3 sr5b Outgoing Calls Fail throw DBL exception |
|
CCM-DST
change does not take effect for Timezone Atlantic Time ( |
|
Callmanger
TOD Routing Update needed for New Zealand DST changes in 2007 |
|
CDP.sys
causing nonpaged pool memory leak identified by Mdl tag |
|
CTI
error in event log when logging out of Ext Mob |
|
Inactive
or Unassigned DN with CFA still forwards calls |
|
Phone
does not display full status message when registration fails |
|
7906/11
display square symbol when the Caller ID too long. |
|
Update
Device Support |
|
CM is
not forwarding the Notification Ind from QSig Facility Messages |
|
Presentation
Indicator is not set correctly in H225 Notify messages |
|
CCM
uses internal msec packet size, ignoring size proposed by caller. |
|
Call
Manager CTLProvider Heap Overflow Vulnerability |
|
Adding
8.3(1) Display instances to all released CCM branches |
|
If
CDR database is offline/suspect InsertCDR service leak memory |
|
IPMA
could not read directory users |
|
TSP
crash at ASB bank in |
|
IPMA
Assistant Console Install throws warning message after Aug 20 |
|
compatibility
issue between IPMA and SMS |
|
Locale
file - target-dictionary.utf8.xml needs to be updated |
|
7940/7960
SIP Phone Won't Display CGPN (Caller ID) - 8.5(0) (POS3-08-5) |
|
TopN
by Number of Calls - By Extension Reports in CAR are missing users |
|
JTAPI
function getType() for calling party returns farEndType = 0 |
|
Unable
to clear CFA from IP phone |
|
InsertCDR
service should handle character ' |
|
Need
a way to control SSH access to phone from CM |
|
Check-in
Cisco 7921 firmware version 1.0(3) to CallManager |
|
Special
number call is cancelled after 1 ring when keypad is locked |
|
Phone
on Antiope vibrates if headset attached when set vibrate alert |
|
User
can not do factory reset if setting access is disabled |
|
High
multicast can degrade unicast RTP voice quality |
|
75%
battery icon appears with full battery |
|
7921
doesn't work with CME unicast paging |
|
Power
consumption high after roaming during a call with tspec enabled. |
|
AXL-SOAP
fails to update services on CallManager 4.1(3) |
|
Pickup
should not fail the action when receiving SsSplitInd with ss2=0 |
|
DA
entries get corrupted due to out of order change notification for DN |
|
ccm
tftp stops building new config files |
|
SOAP
requests return 999 HTTP Response Code |
|
Webknight
Firewall in CCM 4.2.3SR2 stops AXL requests |
|
CallManager
4.2(3) ES 31 Web Knight POP up seen |
|
WebKnight
blocks 'style=', a valid input from CUOM to CUCM |
|
MTP
resource leak if no response are recived to BYE message. |
|
Forwarding
should stop CFNA timer and remove the call from PickupTable |
|
Monitor
table leak due to Q.SIG APDU in setup then Call immediate split |
|
Pickup
fails when call is transferred between interclusters. |
|
Call
Fails When PBX Attendant Console performs Blind xfr back to CCM |
|
ST-Cause
code 47 Resource Unavailable generated for SCCP to H.323 1CPS |
|
Call
over ICT fails when h245 OLCack is sent with wrong LCN number |
|
Faulty
Hi-Res CPU timer affects IPVMS driver on DL 380 G4 3.8Ghz CPU |
|
Phone
not able to place outbound calls |
|
CCM
sends an extra ORC |
|
Change
Notification Fails - DBLCNQueue Counts Rise - DBL Ptr Corruption |
|
15
sec delay due to missing MWI retError APDU |
|
Callback
fails if IPMA proxy line has PickupGroup or CFNA configured |
|
For
signaling only call, CCM should not request bandwidth reservation |
|
After
implementing CSCsb42763, can't view or delete hunt pilot. |
|
CM
4.3- Attendant Console Pilot Point returning busy after CM restart |
|
guinness-
device definition files need to be checked in |
|
MGCPQsigCdpc
process leak for signalling only call |
|
MLA-
ASP file is not found in the when accessing VG224 gateway |
|
MTP
not invoked for G711Alaw call |
CM-6608 CFB/MTP |
|
KeepAlive
interval with CM-6608 CFB/MTP resources |
6608 |
|
6608
T1 resets due to bugtrap |
7905/7912 |
|
CP7912-UK
Locale files are downloaded every time the phone reboots |
|
7912
increase number of digits displayed for external phone number mask |
|
DTMF
Tx failing 7912G |
|
7912G
IP PhoneCannot access corporate directory with French locale |
|
CP7905/7912
phoneDN returned Under DeviceInformationX is Incorrect |
|
7912G
does not boot up after firmware upgrade |
|
CP7912G-The
behavior after the recovery from the DHCP issue |
|
Incorrect
chunk size in http encoding for StreamingStatisticsX |
|
HTTP
URL requested by 7912 misses variable name |
|
7912-Calling
number is missing from received call history |
|
The
memory space of version string is smaller than the macro definition |
|
7912
should retry after HTTP refresh failed |
|
7912
8.0(2) SCCP - phone resets when accessing Corp Dir or other XML |
7914 |
|
Check
in 7914 loads |
|
Add
new icons for sidecar to support Muster release |
7920 |
|
7920
Firmware 3.0.2 Check-in |
7921 |
|
High
multicast can impact battery life |
|
Proxy
URL is not supported |
|
Can
not reset phone when idle url is active |
|
7921
cannot resume shared line hold calls beyond the first |
|
7921
doesn't show missed calls when keypad is locked and LCD went off |
|
No
audio if source reset RTP timestamp in the middle of a call |
|
7921
enters speakerphone mode after call park retrieval with CME |
|
Current
volume can get impacted while configuring other volumes |
|
7921
with CME speed dial can corrupt system message display |
|
headset
mic audio may distort if in noisy environment |
|
DnD
does not work with CME on 7921 |
|
Get a
10 second audio gap after receiving deauth with static WEP128 |
|
Alert
tone does not always play when pushed via Play URI |
7935,7936 |
|
Phonebook
doesn't display numeric number by default in Web interface |
|
Second
phone in a shared line hangs in a failback and failover scenario |
|
Phones
hangs while using restore default from UI in this scenario |
|
Phone
UI displays error when Restore Factory default in a active call |
|
Fields
in "Add New Phone Book entry" in 7936 GUI do not get refreshed |
|
"Server
error-413 N/A" appears when wrong input given in phone book |
|
Phone
book entries duplicate |
|
No
validation for "upload logs" under Diagnostics in phone menu |
|
|
|
No.
of characetrs as password input inconsistent in GUI and phone menu |
|
Call
Park Reversion message not displayed |
|
|
|
Network
settings dont work when 2 phones are in a call |
|
Phone
Book does not accept 24 digits as DN |
|
Only
23 digits displayed of a 24 digit DN though lot of space available |
|
Softkey
templates working improperly |
|
CFwdAll
in an active call breaks the voice path |
|
CP-7936
v3.3.11 can continually reboot after a few weeks on HP switch |
|
7936
may not dial the * character when using Phone Book |
|
Softkeys
missing(7936) ,when huntpilot call is answered with callfwdall |
|
Phone
plays ringback tone if destination phone has CFA set to unknown. |
|
Deleting
the DN freezes the phone |
|
"Http
Server" label in place of Http client |
|
DN
does not display completely |
|
Reboot
does not work |
|
Pressing
menu-> phone button in active call phione in a wierd state |
|
c in
click should be capital on "Passwords/HTTP Port Change" webpage |
|
Help
page does not show hostname |
|
Changing
the ringer during an active call puts the phone on hold |
|
Help
page of time and date does not list all the date options |
|
Help
Page of Network Setup incomplete |
|
Softkey
templates incorrect in case of Shared line |
|
7936
phones intermittently fails to upgrade to new load |
|
Icelandic
characters not shown on 7936 IP conference phone |
|
Spelling
of transfer softkey in case of new call |
|
CFwdAll
softkey is absent when initiating a new call during active call |
|
7936
DN display only displays 11 digits of a 12 digit DN |
|
7936
- tone49(zipzip) has beep beep then sounds like long euro ringback |
|
CP7936
Experiencing Possible ARP Cache Corruption |
|
7936-
conference soft keys becomes inactive after a few calls |
|
Need
support for GetElementManagementFromManagedElementOid |
|
7935
& 7936 stops after 8dhcp discoveries w/no response |
|
DHCP
changes can cause phone to reset while on a call |
|
7936
resets or one-way audio due to exceptions caused by DHCP renewal |
7937 |
|
7937-Device
Definition Files Need to be Checked In |
7940/7960 |
|
7940
/ 7960 reboots when receiving IP fragmented packet |
|
7940/7960
phones fail to upgrade LSC with CME secure authentication |
|
Choppy
audio/jitter in incoming RTP to 7960 causes one way audio |
|
no
audio after high delay or jitter on network with g.729 |
|
hook
switch debounce timer too short on 7940 IP phone |
|
In
speakerphone disabled state, 'Dial' softkey active in a scenario |
|
when
callwaiting tone is invoked, calls stop getting ringback |
|
7960(sccp)
resets under Codenomicon HTTP test suite running |
|
7960/SCCP
resets under two cases of Codenomicon TCP Test suites |
|
7960/40
ignores StartTone Messages when in connected state |
|
Phone
struck in a loop inside the personal address book |
|
Migrate
to use new load authentication key |
|
multiple
issue after upgrade to 3.3.5sr2b |
|
Hold
call is disconnected when primary CallManager gets back |
7906G,7911,7941,7941GE, |
|
NullPointer
Exception on AutoCallAgentImpl.inFocusItemChanged() events |
|
DSP
Configuration Files are not Correct |
|
7911
DEV load contains incorrect jar file |
|
Third-Gen
SCCP Retries Registration 20K+ Times/Day On Phone-Reg-Rej |
|
R2D-
mapPixelCoordinatesToWindow always returns NULL. |
|
Pressing
New Call should let user "Enter Number" |
|
M&R-
new M&R tone command should override playing tone of same type |
|
Tone
not suppose to send to supervisor when selected remote only |
|
Phone
does not show complete information for show inventory command |
|
Change
the immDiv softkey name to Redirect - Update SIP dictionary files |
|
Need
Automation API to get status of headset, mute and speaker lights |
|
Commit
of CSCef34402 broke c6slc, other? pikespeak images |
|
make
'DEBUG' trace anticipated for a 1-way audio problem as NOTICE trace |
|
Phone
doesn't calculate SRTP auth tag correct for certain RTP payload |
|
DC
bias introduced by noise reduction |
|
Play
URI doesn't play ring file after first time push |
|
Guinness-
Continuous unicast traffic resets the phone |
|
C-P-7941
Changes on the Ring Tone go back to Default after a soft reset |
|
Update
memory timings for Goped boot loader |
|
SIP
phone failed to clear Held call when CCM restarted |
|
TNP-
keyboard I/O errors on reset |
|
No
spkrphone dialtone when Trans/Conf button hit on TNP SCCP 8.3.0.9S |
|
ppid
found file system issue with unmount beneath stdio file access |
|
Re-partition
MIPS memory allocated for ZSP |
|
Call
duration timer window on ph display cycles between multiple calls |
|
7971-ringer
volume is too high |
|
7971
unable to come up while detecting Supplicant on both switch port |
|
Guinness-
Beamish models should not have touchscreen enable/disable |
|
7942/7962-
pressing "Cancel" key does not discard change to contrast |
|
797X-
Phone DHCP config data got corrupted during firmware upgarde |
|
Phone
UI locked up when remaining in fail over mode |
|
minimum
send gain not consistent |
|
Static
analysis on debug shell |
|
Broadcom
phones unable to determine source port of unicast 802.1x EAPOL |
|
Add
wideband PLC to codec G.722 and L16K pcm |
|
7975
Gigabit is sensitive to CM signal, and loose many packets |
|
Show
wrong time when using the |
|
Change
dsp cost table for iLBC |
|
Noise
reduction causes highband rolloff on handset |
|
7931-
Overview not in home position at initial bootup |
|
Speed
Dials not working on SIP Phones in a specific scenario |
|
DSP
resets when Noise Reduction is enabled and spike in audio signal |
|
keypad
tones not played on speakerphone when transfering a call |
|
RTCP
socket open error may cause audioserver to spin |
|
Fix
Static Analysis warnings from TNP security code |
|
GoPed-
Auto Line Select does not work as expected |
|
Phone
hangs if it stays on placed calls when the peer ends the call |
|
Third
gen phone may behave wrong under stress registration test |
|
Guinness-
PC port does not forward egress packets |
|
SIP
Phone core dumped after failover |
|
Disable
Speaker/Handset for TNP SIP doesn't disable Meet me Softkey. |
|
echo
on guinness speakerphone |
|
7970
with firmware 8.2.2sr1 speaker not working correctly |
|
Unusable
G711 calls (loud noise) |
|
Automation-
Need enhancement to AutoStream for SRTP or RTP |
|
Automation
does not work on 7911 |
|
need
interface getLineButtonPosition() to AutoCallAgentIf |
|
Phone-
Dial softkey should not be available for PRIVATE numbers |
|
CallHistory
Menu- line key, speaker key, no longer work |
|
Remove
tftp command from Mirzam ROMMON |
|
7971/7941
re-append parameters with a redirected authentication |
|
CDP
can alter statically assigned VLAN |
|
R2d
code doesn't return null reference for corrupted PNG file |
|
TNP
SCCP phone displays "???" for DND linekey |
|
Remove
I-Hold changes for |
|
3g-phones
-- pick up Sun Java patch to address 2007 DST changes |
|
TNP
SIP phone needs to be power reset to re-register in a scenario |
|
slower
error propagation causing ph to become leaf of grand child phone |
|
7971
Shows NPE when rebooted during inactive time |
|
7911/7931/7962-
DSP process memory leak |
|
Filesystem
Privilege Escalation |
|
Volume
Control on Group Listen is Broken |
|
When
zrun exec VM, it returns immediately& unmount takes causing Ph loop |
|
ppid
display notification icon addition |
|
Psylocke
code review |
|
SCCP70.MU-1-0-19S
advertises iLBC and causes the call drop |
|
7931-
Softkeys not Updated in |
|
PPID-
sunvm should not be trying to come up while /dnld is occupied |
|
Noise
Reduction voice metric has erroneous value |
|
Guinness-
Update LCD device driver for 7975 (Murphys) model |
|
supposed
lock issue on CNU rebooting contention problem with init |
|
SA
errors for activate() methods |
|
AutoStream
getRemotePort returns neg value for ports in 60000 range |
|
Guinness- Psylocke SOC SA/Cleanup |
|
Inconsistent
display of DND Feature (in line button) on SIP & SCCP Phone |
|
KA
timer still alive on child phone; phone creating new tranfer process |
|
Audible
MWI support |
|
authentication
fail on parent, but child authenticates OK |
|
Guinness-
keypad device driver for 7945 / 7965 models (Beamish) |
|
SA
baselining for TNP |
|
7931-Resume
SK does not resume call after scrolling to another line |
|
Merge
from DSP Version 4.2 |
|
Phone
goes out of memory after upgrade/downgrade due to OutOfMemoryError |
|
Hearing
Aid Compatibility tests failed on Guinness/Wideworld TNP |
|
Hebrew
chars position too high in softkeys |
|
Comfort
Noise needs to be tuned for Wideband codecs |
|
8.3(1)
SCCP Phone resets during video setup with non-CM6.0 Endpoint |
|
Display
scr. is dark & won't accept input while phone upgarde downgarde |
|
phone
as root and leaf for the same file; two roots for the same file |
|
Phone
with network plugged into PC port can get stuck if link drops |
|
Osage-
Phone drops incoming unicast EAPOL when VVLAN is present |
|
Customer
cannot use Codec of their choice after 8.2 phone load install |
|
Parent
not sending KA to leaf; leaf reroot; end up with TLOAD |
|
Phones
failover to secondary node with wrong cause code |
|
PAE
can't exit due to a file lock during shutdown, phone hangs |
|
Cannot
answer call by going off-hook |
|
TNP
phones on CME can't resume call with Line button |
|
Focus
does not shift to off-hook line while another call is incoming |
|
PPID
FOUND CORNER CASE- init never reimages in certain instance |
|
Focus
should remain on oldest ringing call with mulitple incoming calls |
|
set
ringtone after preview ringtone can crash a 3rd gen phone |
|
NAK
SMT/ORC |
|
7975
Network Stats page displays the wrong NW port info |
|
Guinness-
move interrupt learning code to a helper function |
|
MenuApp
Application has wrong icon in title bar |
|
Merge
Noise Reduction improvements into Mainline branch |
|
Phone
Directory gives incorrect details after upgrade to 8.2.2 |
|
Muster-
Phone Errors when pushing URL's with priority |
|
offhook
w/ handset for the first time after reboot, no dialtone is heard |
|
7962/42
advertises PAUSE capable via Ethernet AUTO-NEG |
|
PPID
Unit Test Findings - TCP Communication Problem on Root Removal |
|
SIP
phones run out of memory in Java heap for every call |
|
XML
Parse error when phone is dialing |
|
7911/7972-
Add tool to dump DSP data structures, initially msg buffers |
|
Remove
redundant model specific dictionary entries |
|
Update
boot loader on Guinness phones |
|
Replace
TI assert function by dspfw define ASSERT |
|
No
dialtone with handset off-hook or using the Speaker button |
|
Change
text on Power Save Config menu of phone from Display to Backlight |
|
Guinness-
Update Touchscreen device driver for 7975 (Murphys) model |
|
Guinness-
update LED test app for 7975 model |
|
SBB/SBCB
& Barge/cBarge call instance focus incorrect after phone reset |
|
OnHook
Dialing from Line2 doesn't work if Line1 and Line2 have same DN |
|
Not
able to configure Directed Call park BLF in 7970/71 SIP phones. |
|
GoPed-
Add Help for Fixed Feature Keys, NavPad, and LocalFeature PLKs |
|
Graphic
Issues |
|
guinness
audio improvements |
|
Guinness-
use port index to update queue link speed |
|
TNP
phones fail to upgrade LSC with CME secure authentication |
|
Enhance
kernel memory utilities to report free blocks in the virtual mem |
|
7970/71/41/61-
DSPBOOTStart-Sync failure btw ZSP and MIPS-MBOX1=DEAD |
|
Need
ability to send hook signal for onhook transfer feature |
|
Phone
does not come back up when the PC and sw cables are reversed and r |
|
new
threaded PPID algorithm with dual TX threads wont shutdown |
|
"Update"
softkey isn't displayed when focus is on LSC |
|
Phones
don't handle fatal Java exception properly |
|
IP
phone fails to parse the encrypted config file |
|
SIP
Tnp Phones display needs to be changed |
|
bug
trap 91 on system reboot |
|
Don't
write cdp.conf file everytime we recieve packet if not necessary |
|
Changes
per UI Evaluation |
|
clean
up syslogs in PPID remote and console logging |
|
differentiate
illegalStateException in getNodeId() |
|
No
help information avail for NAV Left NAV Right button in 797X phones |
|
IDLE
Phone with Open detailview screen cause inconsistant DTMF behaviour |
|
CallHistory
Menu- Going offhook dials wrong number in special case |
|
With
Setting Access to restricted can access Network Config |
|
Phone
gets stuck while resetting |
|
SIP
7970 phones showing RemoteHeld state while it has to be in HELD stat |
|
/usr/cache
out of space - can't create a new file |
|
7961
phone not show Help info for privacy button |
|
Large
increase in PNG graphic processing time |
|
Focus
should remain on oldest ringing call with mulitple incoming calls |
|
Handset
adaptive gain control needs to match the 7940/7960 |
|
Automation-
Need isSelected method in autoobjinfocus |
|
Display
Timer on TNP Phones wrong, Meet Me initiated with Trans Pattern. |
|
Shared
memory access collision between dspfw and driver |
|
JPN-
Cannot Display Kanji via UserToDeviceData |
|
79x1
phone delay to display system message after deactivate DND |
|
Leave
space between display of Internal caller ID and Line Text Label |
|
Guinness-
create unique queue for reserved mcast |
|
turn
on WB handset feature bit in mfgInfo for guinness phones |
|
Background
Image list item irregularities |
|
Intercom-
7931 phone cannot complete onhook dialing with incoming interc |
|
Takes
long time to receive error from phone |
|
SIP
phone stop registering to CCM w/ 50% packets loss |
|
Unknown
name displayed if special characters are in display name |
|
dtmf
issue in CME software conference |
|
7911
Ph unregister flood console logs with Supplicant logged off message |
|
Top
of Softkey Graphics Disappears When Slider Bar is Shown |
|
Add
debugging info-- add brodcast TX/RX count to call trace |
|
phones
should keep the latest Kfactor value in the phone stats |
|
7914
configured over 15 digit in line number behaves very strange |
|
Guiness
7945s got stuck during ppid upgrade |
|
some
SCCP phone types does not play call alert or reminder tone for DND |
|
CallInfo
page displays wrong status for the idle lines |
|
convert
"Can Not" to "Cannot" in all SCCP english dictionary
phrases |
|
SIP7911
stuck during automated upgrade/downgrade |
|
Guinness-
Update BN2 to latest diagnostics version 13.2.0.33 |
|
AutoFeatureIf
invokeDirect returns success when softkey press failed |
|
Headset
LED in wrong state after power cycle |
|
CallHistory
Menu- Can't dial with line key|speaker in special cases |
|
Guinness-
update to latest diags for all guinness phone models |
|
Privileged
Shell Commands available to unprivileged user |
|
Handle
REG ALL FAILED differently to allow LSC installation |
|
Root
phone not offerring new leaf when its children are gone |
|
7975/45/65-
Gig E speed option unavailable Switch port or PC Port settin |
|
Guinness bugtrap- SY MSG- Kernel Shu= 0x6666 |
|
Call
Preservation- sccp to sccp intercom call clearing issues |
|
mislist
processing removes critical files on upgrade [stale file problem |
|
Need
to be able to get the versionStamp for the config |
|
Intercom-
phone does not do talkback if onhook dialing is in progress |
|
ESP
debug message add (passau) |
|
Guinness-
Implement Psylocke programming restrictions |
|
on
speaker, noise or mute tone heard when pressing Mute button |
|
Factory
Reset require for secure phone to move to another CCM |
|
3rd
phones break 802.1x auth when span to pc enabled |
|
Bugtrap
0x91 phones (during fsck) |
|
phone
load need to support new timezones |
|
Guinness-
provide register access for gig testing |
|
2nd
iLBC channel can't be opened as full-duplex to do barge-in |
|
Collapse
|
|
third
gen phones power is initally set high power at boot w/line powered |
|
Phone
web page http-//Phone IP Add shows ??? character for parameter nam |
|
Update
7975 / 7965 / 7945 bootloader for LED changes in new HW |
|
Pre-dial
list shows DN followed by conference after a conference. |
|
flash/buffer
comparison failing |
|
Repeated
Dialing from Call History Menus causes OutOfMemoryError |
|
CallInfo
URL missing VisibleFeatureList tag when application pane open |
|
Secure
conference need support for getting icons from confList |
|
7975-
Add touch panel calibration defaults |
|
Phone
declared as a child twice by same parent due to keep alives TO |
|
SIP
Intercom - enable redial feature |
|
Audioble
MWI (Stutter Tone) is not sounds correct |
|
Time
zone rules do not update correctly on 3rd-gen phones |
|
7911
phone advertise 2 iLBC codec on its capability message |
|
dhcp
memory leak |
|
Change
dsp cost table for G.722 |
|
7941/61
TNP time displays 1 hour early if power cycle |
|
802.1x
packets are not forwarded |
|
Need
a smaller font for the call reference for Makaha and Caffreys. |
|
Private
RIU calls show up in the callinfo list |
|
IP
Phone SSH Vulnerability |
|
Read
linenumber from the config file |
|
Noise
Reduction total energy parameter rests at 28 instead of 0 |
|
7970
phone in low power mode consumes more power than CDP advertisement |
|
Bogus
load name in Phone load element value cause TNP phone to hang |
|
Phone
TFTP request packet for a background image is Malformed Packet |
|
guinness-
code cleanup in dsp device driver |
|
Guinness-
Update diags for Murphys to 13.2.0.23 |
|
TNP
Phone SSH Vulnerability |
|
Update
diagnostics / BN2 for guinness phones |
|
XML
parsing error on LineInfo to turbo phones w/ speed dial configured |
|
MenuApp
Application has wrong icon in title bar |
|
7970-
Malformed UDP packet DOS attack causes phone to freeze |
|
SIP
shows incorrect info for placed intercom call in IntercomHistory log |
|
SIP
phone should disable Callback and DND for intercom call |
|
port
"reset on sleep mode" ddts to guinness code base |
|
Modify
assembly to address Titan Advisory R5691 and c55 Advisory CPU_116 |
|
Multiple
softkeys on the phones are "bleached" on touchscreen drag |
|
Need
automation API to get tthe time/date from the phone |
|
Update
cpk files for Beamish model 7965 phone |
|
Need
to Press Right button twice on Nav Pad to close Line Detail |
|
Guinness-
nmap TCP connect scan crashes 7945 and 7975 |
|
Composed
IPPM messages display + instead of space |
|
Update
power requirements for 7945, 7965, and 7975 phones |
|
Guinness-
Update BN2 to latest diagnostics version 13.2.0.31 |
|
75
phone call numbers over flows the spaces assigned for it |
|
Recording
tone plays abnormally during a call |
|
DSP
process dies while running the call features automation script |
|
LCD
for Guinness 7975 need color register adjustment |
|
SIP
7911 and 7961- Erase config from Settings menu does not reset phone |
|
Font
kerning issue on 7970 |
|
Missing
Pixels on the left side of UI displays on Turbo phones |
|
Guinness
phones need different EQ based on Handset Hookswitch |
|
Phone
does not get registered when daisy-chained with 7961 phone |
|
Customer
is experiencing one way audio calls |
|
TNP
improvements- /bin/sh should always be a POSIX-compliant shell |
|
7971GE-
Sleep Mode issue |
|
7941
- BLF speed-dial status LED does not work |
|
PNG
Broken- Phone fails HTTP GET if earlier HTTP request is not finished |
|
wrongly
uses tftp server as log server |
|
Rings
shouldn't be configured for intercom lines |
|
SIP
phone does not answer by lifting handset |
|
LCD
for Guinness 7975 phone displaying inaccurate color balance |
|
Phone
sends different help ID for intercom line |
|
TNP
sempahore traverse |
|
Shared
line display & going offhook while in active call distort display |
|
command
parse error and command search fail on 7970 |
|
JAL
doesn't work as per requirement with c-Barge Conference |
|
Frequency
Value for Steady Dial Tone After Stutter is Wrong |
|
PPID
Unit Test Findings hash test ugliness |
|
Jphone
and init.tab and sleep interaction |
|
Update
diagnostics for Guinness phones to version 13.2.0.36 |
|
Phone
does not get registered when daisy chained |
|
pressline
2 not working for 2nd line of 7941 |
|
SCCP
phone does not register back to publisher after restart. |
|
GUI
stuck after changing contrast |
|
SA
for img_main (image daemon) |
|
Enhancement-
provide an indication of when flash was last formatted. |
|
Guinness-
Fix the printing of the Chip Version Register (CVR) values |
|
Ph
hits max file download timer of 60 min during firmware upgrade downgr |
|
TNP
Phone 7941 second line line button will light up for incoming call. |
|
SIP
phone init a new call when pressing the line that already has a call |
|
Hung
RS-232 port causes phone upgrade failure |
|
Response.Redirect
fails |
|
When
ph is going to safe mode or TLOAD its background should be cleared |
|
Ph
stuck in IDLE state after Java Error without CallManager menu Entry |
|
7945/65/75
Hardware version 6.0+ uses external gamma |
|
7970-
nmap TCP connect scan crashes 7945 and 7975 |
|
7975-
PC port goes no link after reconfiguring to 1000F |
|
G722
Monitoring call could not be setup for iLBC primary call |
|
Memory
Leak on phones with repeated calls with very short call hold time |
|
Event
needed for reset |
|
Change
the CiscoError, CiscoStart and CiscoReboot png files for new logo |
|
Phone
core dump while running the call features automation script |
|
7971
SIP/SCCP- PC port can be enabled after being disabled from CCM page |
|
|
|
Erroneous
Behavior when DialLine URI on Intercom Line that has call |
|
Gross
timeout for downloading file with DLOAD & TLOAD should be changed |
|
when
callwaiting tone is invoked, calls stop getting ringback |
|
Host
unicast traffic are not forwarded to the egress PC port |
|
GoPed-
localization work for Muster |
|
Phone
hangs while downloading PNG files |
|
7970-
implement ethARLCache functions |
|
TLoad-
timer_start fail - doGrossTimeout-serial issue seen on 16s load |
|
831-Settings
button access set to restricted disables directories/servic |
|
Callback
softkey is presented but it doesn't do anything. |
|
New
Default Background Image Required |
|
Jake
Featurette check-in |
|
Cloudraker-XML
Parser- xml parse error on event ID of Redirect Softkey |
|
Cloudraker-SendDigits
URI fails to send in-band dtmf |
|
Wideband
Handset available for config on 7931. |
|
7945/65/75
bounce link on soft reset for both PC and network ports |
|
disable
audio output during bootup |
|
Alien
crosstalk is degraded after CSCsh75383 is fixed |
|
7971
DHCP address from data vlan |
|
New
Default Background Image Required |
|
Cloudraker-
Missing support of IconIndex in Title element |
|
Turbo/Goped
sometimes experienced resets after power recycle |
|
7945/65
becomes inactive after CCM down |
|
7961
crashed when running Codenomicon https suite(Test #9) |
|
call
on sharedline lost on phone - both users hit endcall on other line |
|
Update
diagnostics in BN2 for 7931 |
|
Ph
not register afte XML Parser Excep seen during config file parsing |
|
Cloudraker-phone
fails to come up if deleted and tries to Auto-reg SIP |
|
Turbo
Bootloader Changes |
|
7962
does not come up with load 8-3-1-10 |
|
7911
phone crash when switching to Arabic locale |
|
Phone
Directory gives incorrect details after upgrade to 8.2.2 |
|
TNP
Phone Update needed for New Zealand DST changes in 2007 |
|
CIA
1085- lower Voice Mail status line to below DND state. |
|
TNP
Phone use Narrowband Vol Table even for WB |
|
CallBubbleSelected.png
is one pixel too wide for beamish |
|
Ph in
stuck state after capfList config structure change in SEP MAC file |
|
Ph
got stuck in Settings screen when Settings is pressed while dialing |
|
7970
RLR is softer |
|
Phone
API startMedia request, parameter "receiveVolume" not working. |
|
7975G
characters look fuzzy/not formed correctly |
|
Pixels
sourounding the active UI tab are not black |
|
Callback
Message screen mixed up with Placed call screen |
|
Cloudraker-
XML parser- Hardened Soft Key Files schema rules |
|
Resource
Image updates for FCS |
|
Update
Guinness BN2 for Memory Bist tests |
|
Darker
greyscale images cause unreadable display on 7961/41 |
|
Guinness
handsfree mic signal can clip |
|
Cloudraker-
XML Parser- No Error when tag is duplicated |
|
Update
Guinness BN2 files with diags version 13.2.0.60 |
|
Guinness
Phones do not respond to 802.1x Re-authentication Requests |
|
Missed
call history incorrect for forwarded calls |
|
Underworld
- XML Parser Code changes |
|
Underworld-
Phone does not shows "bad ring list" for erroneous ring file |
|
Cloudraker-
XSI- xml push onFocusGained to phone executes 3 times |
|
SBB/SBCB
& Barge/cBarge call instance focus incorrect after phone reset |
|
Update
Guinness mfg image to include new diagnostics ver 13.2.0.49 |
|
PS
loads fails to switchover to Jap locale |
|
Resource
Image updates for FCS |
|
Underworld-
Config File schema errors and issues |
|
XML
Schema hardening prevent encrypted & non-encrypted config parsing |
|
7970
with firmware 8.2.2sr1 speaker not working correctly |
|
7962-
packets egressing PC port should have PC vlan untagged. |
|
New
generation phone have lower volume then older phone types |
|
Null
pointer exception on XML Parsing for SIP phones |
|
ESW
clock not initialized properly by boot loader |
|
7962
barge in no voice |
|
XML
data can't be rendered to IPphone |
|
Guinness
Handset RLR incorrect |
|
AEC
suppression can degrade voice quality scores on Guinness |
|
Guinness-
Color models are displaying visual noise on power cycle/reboot |
|
Pixels
surrounding the active tab are not black |
|
Cloudraker-
CFWDALL and MCID not working on SIP phones |
|
TNP
SIP phone can not failover to SRST due to wrong port |
|
Start
Media Response does not returns codec string correctly |
|
Guinnes
handset - "highs" are little too high |
|
Goped
Bootloader Changes |
|
New
XML parser unable to display another Ph web page in XML services |
|
TNP
phone corrupt background image causes blue image and crash |
|
Turbo-
Malformed UDP packet DOS attack causes phone to freeze |
|
Broadcast
Storm one way audio for 7961 SIP |
|
Update
diagnostics in BN2 for 7911 / 7906 |
|
Guinness-
Malformed UDP packet DOS attack causes phone to freeze |
|
Analog
codec audio output enabled in early stage |
|
802.1x
packets are not forwarded |
|
SBB
feature does not work |
|
Update
Guinness BN2 mfg image to release signed |
|
Calls
transitioning to OFFHOOK state should take focus |
|
send
specific XMLobject code into 7970, phone cannt request EM service |
|
Guinness-
improve AEC doubletalk performance |
|
TNP
SCCP ph unable to come up and register with sidecar 7914 attached |
|
Underworld
- XSI Backward Compatibility Changes |
|
SDK
version updated to 6.0.2 for 8.3.1.release branch [8.3(2)] |
|
support
new Spansion flash part |
|
OS
PLL init setting unnecessary |
|
Resource
Image updates for FCS |
|
3rd
gen phone may loose personalization after rereg to another CCM |
|
Phone
will not load from case sensitive TFTP server |
|
Bug
in vFillShorts assembly source |
7942/7945/7962/ |
|
Check
in Guinness phone firmware to CallManager |
7985 |
|
7985
Screen Powersave LED indicator can't be distinguished from MWI |
|
7985
sources from random port rather than from standard specified in olc |
|
7985
should use symmetrical UDP port numbers |
|
Visual
call Pickup notification fails when line audio alert setting off |
|
7985
phone not working with Mobile Connect service. (CMM/SNR) |
|
7985
does not send out video packets w/ IPMA configured |
|
Star50
feature is not working on 7985 video phone |
|
7985
phone with no voice vlan configured fails DHCP/ip address. |
|
7985
enters reboot loop on upgrade when using Alternate TFTP |
|
7985-
the ">>" and "delete" softkeys in edit dial screen
arent working. |
|
7985-
restart loop if load is different between DHCP and alternate TFTP |
|
7985-
Phone crashes when long input is entered in inputboundary test. |
|
7985-
Ringer stops riniging when try to change ringer drg outgoing call |
|
Ringer
stops when 2 incoming calls on 7985 & 1 call ended. |
|
7985-
Phone dumps hex value on screen with imageboundary service test. |
|
7985-
IPMA - Manager screen goes off after every change |
|
7985-
Screensaver leaves chars all over screen |
|
|
4.1(3)sr5 (Based on ES106)
CAPF must upgrade to latest RSA libraries |
|
Improvements in User Input Validation |
|
After CM 4.2.3 ES26, third
generation phones update gives CDP warning |
|
CM 4.3- Attendant Console Pilot
Point returning busy after CM restart |
|
For signaling only call, CCM
should not request bandwidth reservation |
|
Multiple Alpha CallManager
Servers Core Dumped Simultaneously |
|
15 sec delay due to missing MWI
retError APDU |
|
Cannot Insert Phones Using BAT.
|
|
Phone doesn't register after
reset, stuck in Requesting Template |
|
DA entries get corrupted due to
out of order change notification |
|
Media does not handle saved
connections properly |
|
MGCPQsigCdpc process leak for
signalling only call |
|
MTP resource not releasing
properly btw MTP an MoH by callmanager |
|
DA entries get corrupted due to
out of order change notification for DN |
|
AXL to write empty fields as
empty strings in SQL as CCMadmin does |
|
SOAP requests return 999 HTTP
Response Code |
|
Updation of Barge Parameter
fails in Service Parameters Page |
|
device definition files need to
be checked in |
7985
7985 Screen Powersave LED
indicator can't be distinguished from MWI |
|
7985 should use symmetrical UDP
port numbers |
|
Visual Pickup Notification
sometimes does not overwrite status line |
|
7985 phone not working with
Mobile Connect service. (CMM/SNR) |
|
7985 does not send out video
packets w/ IPMA configured |
|
7985 phone with no voice vlan
configured fails DHCP/ip address. |
|
7985 enters reboot loop on
upgrade when using Alternate TFTP |
|
7985- the >> and delete
softkeys in edit dial screen arent working. |
|
7985- restart loop if load is
different between DHCP and alternate TFTP |
|
7985- Phone unexpectedly
shutdown when long input is entered in inputboundary test. |
|
Ringer stops when 2 incoming
calls on 7985 & 1 call ended. |
|
7985- Phone dumps hex value on
screen with imageboundary service test. |
|
Ping replies from the phone are
not recognized by the originating host |
7937
7937- Device Definition Files
Need to be Checked In |
4.1(3)es106 (Base for 4.1(3)sr5 & sr5a & sr5b)
Call has a negative CI number |
|
H225Cdpc Needs To Handle DstopReq
In Paused State |
|
Call Control To Address Missing
ssRejectionInterceptInd Event |
|
RTMT JVM needs new timezone
data to support 2007 DST changes |
|
Phone Service subscribed by Autgenerated
Dvice Profile is set to default |
|
Adding THX and Babylon5
features |
|
CCM drops APDU's received in a
Progress message while in Transit mode. |
|
Aupair service terminates within
function CDBNotifyClient-isRunning. |
|
Aupair unexpected shutdown On
51st NCS Connection Request. |
|
Long delay when calling
overlapping DN from Webdialer. |
|
No web access cfg option for
7941/61 in CCM device donfiguration page |
|
Unable to insert 7941 phone
with Device Security Mode as Authentication |
|
QRT misreading First and last
write in report file |
|
CCM- GW is intermittently lost
from route-group route-list |
|
6608 PRI Gateway stayed up even
when CCM lost connection |
|
MGCP backual message with
length of 12 bytes |
|
Router identify a very short
DTMF as a valid DTMF |
|
CTI is sending
CtiDeviceCloseNotify during failover/failback scenario |
|
Phantom call stuck in attendant
console client servicing broadcast queue |
|
ES/SR Stopservices logging to
stopservices.txt instead of ES/SR logfile |
|
OS 2000.4.3a Upgrade Shows 110%
On Stopping Services |
|
ES/SR Need to reboot twice
after 3.3(5)ES50 Uninstallation |
|
ES/SR Need additional debug for
commands run during installation |
|
Merging local dictionary in CCM |
|
CCM unexpectedly shutdown while
running ctigw (CUPS) load testing |
|
IPMA-RTMT counters shows wrong
value for IPMA services |
|
SCCP analog GW Virtual endpoint
registration is rejected by CCM 4.1(3) |
|
called number display on
calling phone across ICT shows only DN |
|
add/updateTransPattern-provideOutsideDialTone
element is not present |
|
ES/SR -
Update uninstallation handling |
|
ES/SR Internal reboot function
doesn't work when executed remotely |
|
ES/SR Update Stopservices to
stop all COM objects |
7902/7905/7912
Phone response status
inconsistent between models |
|
7912 phone should not send
StationFeatureStatReq if feature is not confi |
|
7905- Japanese characters are
shown as ?s in EM screens |
|
CP-7912 can not use 255 as last
octet of SRST address. |
|
IPICS Channel selection by
select key does not work intermittently |
|
DnD fails on 7912s |
|
7912 w/alt tftp disabled does
not read TFTP server from DHCP |
|
7912 can not resume multiple
calls from hold |
|
Connection Monitor Duration
changes not applied to 7902 |
|
7912 cannot make new call after
lisfting handset |
|
Malformed XML Delieverd from
7912GA when using DeviceInformationX |
|
No response to UserToDeviceData
for Key-xxx URI passed from CTI |
|
Init-CallHistory URI does not
re-set status line on 7905 |
|
call waiting tone doesn't stop
when the second call hangs up. |
|
7912 prefixes fastdial with
'undefined' |
|
7912 affected by ARP storm |
|
7912 authentication problem -
password encoding |
|
IP Phone Service problem with
7912 http redirect v8.0 |
|
Able to Change Ring Volume Even
when Setting Access set to Disable |
|
7912G-A phone does not obtain
address when voice vlan = access vlan |
|
CIA 650- Randomize TimeDateReq's
to Call Manager from 7905/7912 |
|
CCM drops APDU with multiple
invokes received in Alert message. |
|
H225Notify Connected number IE
not handled in some states |
7935/7936
Phone Button does not work |
|
7936 with 4.2SR1 cannot dial
digits when in call state 3 (Ring Out) |
|
Scrolling to the end of the
line in EditDial causes 7935/7936 Reboot |
|
7936 not passing DTMF while in
alerting state. |
|
DTMF tone will not play for
consecutive same digits with 7936 |
|
Display is not uniform when
dialing an non existing number |
|
Mute dosen't work with Ping
when CCM fails over |
|
Phone dosen't ring while
viewing the MAC address details using **6 |
|
7935 and 7936 do not support
40, 50, and 60ms frame sizes |
|
Phone displays In Use Remotely
with out shared line in SRST mode |
|
LED Status changes when the
Transfer softkey is selected in SRST mode |
|
7935/36 need to support the
priority field in DisplayPriNotify message |
|
Polycom 7936 doesn't refresh
after saving the Alt TFTP address |
|
Main/Secondary TFTP Address
cannot be modified when DHCP is disabled |
|
Conference not working on 7936
in SRST mode |
|
7936 Phone does n't
allow/display full domain name. |
|
7936/7935 does not support JOIN
feature of CCM 4.0 |
|
Renumber 7935 firmware load
name to match the CCO versioning |
7940/7960
Animated circle (reset icon)
seen continuously in a scenario |
|
Add new cons for sidecar to
support Muster release |
|
7960 not allow to select 2nd
call of a conference call on shared line |
|
A call picked up is not
recorded in 'Received calls'. |
|
Upgrade LSC menu strings not
flushed on moving out of tht menu. |
|
7960 stops sending CDP packets
- causes do1x error disable switch port |
|
Phone remain in Configuring IP
state even with proper DHCP response |
|
Option 66 preferred over option
150 based on appearance in DHCP ack. |
|
7960/40 skinny do not detect
handset with failover to SRST |
|
Unicode Special Characters
blacked out on 7940 and 7960 SCCP phones |
|
Several call progress tones
need to be louder |
|
Secure Conferencing Icons for
Muster |
|
7960 phone does not calculate
srtp authentication tag correctly |
|
Placed call list shows '*' for
FAC enabled calls |
|
Secure SCCP Phone Conference
Initiator unexpected shutdown on Hangup |
|
7940 ph does not accept new req
after rejecting invalid IP address req |
|
7960 SCCP does not play beep
tone when DND incoming alert is configured |
|
Phone temporary rejects HTTP
connection when its sockets are available |
|
Static, white noise heard w/
7960 7940 logging into unity with G729 |
|
Update Cisco Logo on phone web
pages |
|
Update the copyright year to
2007 on the boot display for the mid-range |
|
7940/60 not streaming sometimes
when using encryption |
|
StreamingStatisticsX reports
phone as idle when call is active |
|
IP phone at remote offices
stuck in opening. |
|
Transfer call leg connects
while held leading to call drop, media leak |
|
Resolved the race condition
caused by SsManager registration lost due to link issues. |
|
Checking in latest tone file for
third generation phones. |
|
Build phone loads |
|
JPN-Cancel softkey not
available for configuring 7960+7914 |
|
phone displays Select Ringer...
for Invalid DistinctiveRing.xml |
|
UI screen is grayed out when
i-button is pressed |
|
Autodial cancelled is shown for
a Phone in RingIn state |
|
Phone displays AutoDial Cancel
in transfer scenario |
|
7960 tries fallback to CCM that
has CCM service shut but port 2000 open |
|
Phone Softkey should be greyed
out for Disable Speakerphone and Headset. |
|
7960 produces garbled audio and
repeated words for PA Help |
|
Softkeys within various
Settings submenu not responding if held |
|
DN not displayed in a hold
scenario after line button press. |
|
Init-CallHistory URI does not
re-set status line on 7960/7905 |
|
Phone displays Callmanager
parameter as UNDEFINED to boot up process |
|
revertPriority = Even fails
when Hold Reversion call is oldest |
|
Integrate DSP rev 4.0(2) |
|
parked calls get loud tone when
picked up from 7960/40 on CME 4.0 |
|
Callback can not be activated
for a busy extension |
|
Abbreviate dialing should not
be available if phone not able to call |
|
need to press line button twice
to answer an incoming call |
|
Mute light stays on after audio
broadcast is complete |
|
ST- 7960 secure phone got TLS
error with SRST after CCM 4.2.2 upgrade |
|
one way voice when the
timestamp field in the RTP packets rolls back |
|
RTP Tx URI request should be
rejected when a call is active |
|
7960 does not differentiate
local hold call and remote hold call |
|
40/60 - LA dev size grown above
acceptable size limit |
|
7960 with voice vlan resets if
IPC is connected to 3rd vendor switch |
|
phone doesn't handle the DHCP
next server field and option 66 correctly |
|
7960 displays XML error on
hitting directories button with French locale |
|
Phone hangs with HIGH CPU
detected- during EM logout & locales installed |
7906/7911/7941/7961/7970/7971
Phone Directory gives incorrect
details after upgrade to 8.2.2 |
|
TNP- keyboard I/O errors on
reset |
|
7970 phone in low power mode
consumes more power than CDP advertisement |
|
Phones failover to secondary
node with wrong cause code |
|
Network Locale Version
backwards compatibility |
|
Third gen phone may behave
wrong under stress registration test |
|
3g-phones -- pick up Sun Java
patch to address 2007 DST changes |
|
Hung RS-232 port
causes phone upgrade failure |
|
7971/7941 re-append parameters
with a redirected authentication |
|
7914 configured over 15 digit
in line number behaves very strange |
|
phone UI Locks up when adjust
Speaker Volume during registration w/ BLF |
|
third gen phones power is
initally set high power at boot w/line powered |
|
3rd gen phones running
8.0(4)SR1 unable to adjust ringer after a call |
|
u7961/41/70 stuck at requesting
after phones inbound web access disabled |
|
PNG Broken- Phone fails HTTP
GET if earlier HTTP request is not finished |
|
After flash reformat phone gets
flash Programming failure errors |
|
Memory Leak on phones with
repeated calls with very short call hold time |
|
Pressing New Call should let
user Enter Number |
|
Bugtrap 0x91 phones (during
fsck) |
|
Composed IPPM messages display
+ instead of space |
|
Unknown name displayed if
special characters are in display name |
|
Exit softkey stops UI when in
Security Configuraiton/CTL File submenu |
|
TNP phones on CME can't resume
call with Line button |
|
make 'DEBUG' trace anticipated
for a 1-way audio problem as NOTICE trace |
|
Customer is experiencing one
way audio calls |
|
SenderJoins & Byes values
were different regardless of call status |
|
GUI stuck after changing
contrast |
|
Osage- Phone drops incoming
unicast EAPOL when VVLAN is present |
|
Call duration timer window on
ph display cycles between multiple calls |
|
Idle sftkeys displayed on new
incoming call after transferw/rel image |
|
AutoObjInFocusIf.getLabel
returns incorrect information for a call item |
|
Response.Redirect fails |
|
IP Phone SSH Vulnerability |
|
Internal calls are having one
way audio |
|
Filesystem Denial of Service |
|
Phone doesn't calculate SRTP
auth tag correct for certain RTP payload |
|
Stutter Tone quality problem
when using speaker / line button |
|
Focus should remain on oldest
ringing call with mulitple incoming calls |
|
Phone displays CM down in a
active call during failback |
|
7961 phone not show Help info
for privacy button |
|
No dial tone is heard after
togglling the hookswitch in ring out state |
|
Focus should remain on oldest
ringing call with mulitple incoming calls |
|
CallHistory Menu- line key,
speaker key, no longer work |
|
SIP Phone goes for a reset when
proxy address name starts with _ |
|
phone resets after warning
out-of-chunks for memory tracking |
|
Caller-id is not updated
correctly for conference calls |
|
Retrieving a parked conference
call, disconnects the call |
|
Phone unexpectedly shutdown
running Codenomicon SIP test 4913 |
|
unable to do cfwdall if kpml is
enabled in sip-srst mode |
|
SIP phone failed to clear Held
call when CCM restarted |
|
call tranfer after cfw noan on
tnp sip phone failed |
|
Incorrect Date header value in
SIP REGISTER request |
|
SIP Phone needs to also detect
non-localized Conference |
|
Number stored in missed calls
not updated upon receipt of SIP UPDATE |
|
Not able to Set CallFwdAll on
tnp sip phone in particular scenario |
|
TNP SIP sometimes sending
malformed to or from header |
|
7970 sip sends invalid presence
subscription causing high CPU |
|
Failed on multipl forward from
SIP phone to SCCP phones |
|
tnpsip phone doesn't light up
blflamp when destination press callfwdall |
|
Phone unexpectedly shutdown
when messages hard button is hit. |
|
Call not forwarded after
CTINewCallAcceptTimeOut on SIP TNP phone |
|
Transcoder is not able to
handle correctly locations |
|
Active Server Pages exception
first time CCMUser page is loaded. |
|
7936 Phone Displays Host not
found when accessing corporate directory |
|
Need ability to tag dashes on 12
digits calling party number |
|
H225 / SETUP RedirectIE not
populated when VMprofile is created w AXL |
|
Callmanager Disconnects BRI
call with Call State Mismatch |
|
Added Prefix on calling num.
for inbound calls removed from CDR records |
|
CDR Analysis and Reporting does
not reflect new DST changes |
|
Time Schedules Limitation |
|
Calls not transferred to always
route member after hold timer expiry |
|
WD logs ERROR-WDNotStarted -
Failed to startup WebDialer application |
|
CCM-DST change does not take
effect for Timezone Atlantic Time ( |
|
DirectoryConnectionFailed
alerts when DNS server unreachable |
|
SIP does not return error when
failed to open UDP port for SIP trunk |
7921
Check-in Cisco 7921 firmware
version 1.0(2) to CallManager |
|
Unknown DRQs CM to GK |
|
Call Redirect and CcSetupConf
at same time in CM Call Processing |
|
TransferManager splits pair of
SsInfoInds to 2 dif. Transferring process |
|
Double
TransferStart/TransferEnd caused by SsRedirectCallInd |
|
Detailed RoutePlanServer Trace
Results in CallManager Restart |
|
Redial Onhook fails when
Routelist contains QSIG+NON-QSIG Route Groups |
|
Callmanager TOD routing not
updated with DST patches |
|
Need to change PTT URL to
Application URL |
|
CTI is not setting more flag
correctly when more than 50 Park DNs |
|
Fail recieving SIP message when
there are a lot of SIP Trunk |
|
Cisco VoiceMail Port Wizard
freezes when attempting to add port DN's |
|
Install of 4.1(3)esA0 fails |
|
Forwarding Table incomplete
after CCM loses connection to Publisher SQL |
|
SIP Trunk sends 200 instead of
488 on reinvite with no voice caps |
|
TSP - Update Unmodified Calling
DN with Modified when call is Offnet |
|
Attendant Console returns error
if dial busy station |
|
Need to have 4 new Service
Parameters to control the cgpn prefix. |
|
Device/Line goes OOS when CCM
receives LinkOOS from other node |
|
H.323-NonDialable Redirected
Number Causes Corrupted CDR |
|
Need Connected Number IE
support in H225 CONNECT message. |
|
MGCP-Non-Dialable Redirected
Number Causes Corrupted CDR. |
|
Phone hangs/freezes in a blind
transferred scenario |
|
Unable to update a time
schedule which has over 22 time periods |
|
When conferencing,
"Invalid Conference participant" is shown on phone |
|
Merging local dictionary in CCM |
|
TAPI does not always indicate
correct CFA status on phones |
|
Check-in 7921 firmware to
CallManager |
|
Cannot manually update / change
phone load in DEVICE DEFAULTs page |
|
race condition leads to MTP
leak |
|
CM Cdcc / bandwidth leak -
HuntList stuck in paused state |
|
CCM fails to send DLCX when
receives QSIG ReleaseComp before CRCX Ack |
|
right click transfer in
attendant console fails, receiver gets MOH |
|
Create Voice Mail is not
working When MLA is Enabled For FAUser. |
|
MLA- ASP file is not found in
the when accessing VG224 gateway |
|
Unable to create new or modify
VG224 ports. |
|
Need update to
"devicelistx.asp" to support new Cisco 7921 wireless phone |
|
Redirect call across 3 ICT
disconnected when multiple hold/resume |
|
MGCP/Qsig User name not
displaying , Alerting name with ACSE |
|
H245Interface does not use
received h245ta to start H245 Client Session |
|
AXL getUser fails after AD
plugin integration |
|
ST-TFTP service does not build
device config files after upgrade |
|
The phone config files are
missing in TFTP2 server |
|
Callmanagers do not have all
timezones included in Date/Time Group |
|
Update 7921 CSV and XML files
for FCS |
7920
7920 3.0.1 FIrmware and XML
Schema Check In |
|
Full Access & Read Only
Access users are denied to view some pages |
|
MLA generates error when
configuring CSS for DN |
|
Error Message ASP file is not
found in the mapping for ROUser |
|
Full Access user Not able to
Run IPMA Wizards. |
|
FullAccess User Can't edit HL/P,
RL/P, DP from Route Plan report. |
|
Multiple change notifications
received for Route filter clause update |
|
getHuntList response with wrong
name space |
|
AXL removePhone API doesn't
remove the autogenerated device profile |
|
HuntList needs to be fixed |
|
MediaManager is not releasing
the pre-allocated MTP resource |
|
H323 FastStartCCM Closes wrong
forwardLogicalChannelNumber in CLC |
|
CCM does not allow IPVC PSTN
call to be setup with G722 |
|
Race ConditionStationOffHook at
same time as CcSetupReq received |
|
Perfmon of >1 CM Shows 6624
GW Port-1 Registered Simultaneously |
|
No voice after Call forward in
a scenario-Call Diversion by reroute |
|
Clean up the huntlist trace for
better trouble shooting |
|
hunt list incorrectly extends
call to next line group on race condition |
|
CCM does not start media in
some scnario involving IPVC GW and Tandberg |
|
media resource status is out of
sync between MatrixControl/Call Control |
|
Redial not working in a
scenario involving overlap sending |
|
Allow VideoCFB to update
itself's capabilities |
|
No transfer start event sent
when CTI app redirects call during a trans |
|
H.323 phone calling 7960 legacy
SIP over H.323 ICT fast start fails |
|
Incorrect Missed Call Information
when Call is routed via HL/LG |
|
CTI Route point does not
unregister when administratively reset |
|
CallManager 4.2(1)sr1a
-redirect and transfer occuring at the same time |
|
Locations Out of Bandwidth
causes unexpected Unity Failover |
|
TFTP unexpected shutdown When
Length Of File Name Exceeds 256 Characters |
|
TFTP stop rebuild cache for
some specific events |
|
When CCM 4.2 is Secure, HTTP
will not serve Un-Signed files, like TFTP |
|
callInfoDisplay -Case
Sensitivity different in getPhone and updatePhone |
|
Failure adding member to
CiscoAdminRepToolAdminGroupUsers Group. |
|
RTMT (RISDC) not showing true
value of CTI items when threshold reached |
|
Cannot login into Tomcat Web
Application Manager |
|
User field
"Department" - Extending beyond 30 characters to 40 or more |
|
CallManager input validation
needs improvement. |
|
ScalabilityImprove WebDialer
call rate on 7845 to 4 calls/sec |
|
Unable to insert 7941 phone
with Device Security Mode as Authentication |
|
CCM4.1(3)ES. SQL error when
inserting a 7961 phone |
|
Add support for Security
feature in Communicator |
|
3.0.1 English Dictionary Check
In |
7935/36
7935/36 reboot using corporate
directory search on 3'rd party LDAP server |
|
7936 with CCM 5.0 displays
Server Not Found when access Corporate Dir |
|
7936- Can gain access to web
interface w/o admin password |
|
7936 does not register G.729a
capability along with G.729 capability |
|
Selecting Tone Test and exiting
hangs phone |
|
Setting up Admin VLAN id brings
up the phone without a DN |
|
7936/35- Ignore CDP V1 message
for VLAN configuration purposes |
|
7936 phone hangs when pressing
hold & resume |
|
7935 does not recover after
power/network loss |
|
7936 phone shouldn't release
its VLAN until the TTL(CDP message) expired |
|
UI displays Failed to set VLAN
Idwhen changing n/w setup in activecall |
|
When we dial the DN through web
page ,message flashes for sec & proceeds |
|
7935 does not register G.729a
capability along with G.729 capability |
|
Change Notification fails to
update Digit Analysis. CallForward fails |
|
MGCP PRI should prevent
repetitive datalink up and down |
|
IdleCI not passed via NotifyReq
when transfer fails |
|
IdleCI not passed via NotifyReq
when transfer fails |
|
Provide a user identity for
call |
|
TAPI Reports 7941 & 7961
Phones as Unknown Device Types |
|
TSP unexpectedly shutdown on
application server |
|
missing 7906 default load
8.2(1) |
7985
Packets received on PC port are
not forwarded in some configurations |
|
7985 does not display animated
icon w/ RTPRx |
|
Restart reason sometimes is not
correct under Network status |
|
Phone can rarely stop making
calls after CCM failover/failback |
|
Confrence List Remove feature
does not work on CCM 5.0 |
|
Invalid dialed number when
dialed from directory displays no information |
|
Callback Notification window
does not close after Dial is pressed |
|
Phone sometimes does not
fallback to the correct Standby CCM |
|
Wrong display of softkey sets
and callinfo on IPMA assistant phone |
|
IPMA manager should not exit
from IPMA service w/ 1 assistant |
|
Phone did not register with the
Call Manager after a network power loss |
|
Phone unexpectedly reset during
a long duration H.263 call |
|
Some softkeys not work
correctly with CiscoIPPhoneInput object |
|
7985 phone not working with
Mobile Connect service. (CMM/SNR) |
|
7985 un-registers from the Call
Manager after the switch speed changed |
|
Network status should contain
last restart reason |
|
Hoot & Holler service does
not display Handset icon with RTP/Rx RTP/Tx |
|
Visual call Pickup notification
fails when line audio alert setting off |
|
7985- Ignore CDP V1 message for
VLAN configuration purposes |
|
Equation type input can have
unexpected delay when pressing numbers |
|
Pressing a number in Ring Tone
menu works differently than other phones |
|
There is no Call Status
information available via the web pages |
|
7985 appends devicename in HTTP
request when searching directory users |
|
Changing volume during the Hoot
& Holler service cause audio to be sent |
|
Hoot & Holler icon was not
removed after exiting the service |
|
Background image after download
is obscured by the image menu |
|
7985 can not handle URL with
255 char. |
|
PC Voice VLAN disabled does not
work with Admin VLAN |
|
IPPA phone service shows some
unexpected error messages when logging in |
|
Call accross ICTs may fail when
hold or transfer |
|
Call accross ICT trunks may
fail when hold or transfer |
|
CTI Ports/Route Points do not
go in service after reset |
|
Overlap Sending broken when
using redial function while phone is onhook |
|
Incorrect DNIS in the CDR when
using speedial and Route Pattern Overlap |
|
Error on Service Parameter on
CCMAdmin |
|
CallManager should handle
T1-CAS incoming call after GW channel OOS |
|
CallManager MGCP T1 CAS
Channels Must Recover from Out of Service (OOS). |
|
OpenSSL DoS
vulnerabilites- CVE-2006-2937 & CVE-2006-2940 |
|
ccm.exe unexpectedly shutdown
with c0000005(access violation) due to SIPHandler thread |
|
Locations Out of Bandwidth
causes unexpected Unity Failover |
|
Aupair unexpected shutdown On
51st NCS Connection Request |
|
CCM reporting encodingStyle as
ISO-8859-1 instead of an http URL |
|
Update needed for N America DST
changes in 2007 |
7911/7941/7961/7970/7971
Beep tone max power is only
-22dBmO |
|
FSCK stuck in deadlock with
syslogd |
|
Enumeration Pattern Code
Updates |
|
Phone sends corrupted RFC2833
packets when SRTP enabled for call |
|
Dev Studio changes to make
building Communicator easier |
|
Secure phone does not retrieve
the SEP file |
|
7931- Call Plane Detail View is
not open after On-Hook dialing |
|
CiscoIPPhoneStatusFile
LocationX parm not used for small image size |
|
Commit of CSCef34402 broke
c6slc, other? pikespeak images |
|
Titan dsp host could 32-bit
read between dsp firmware two 16-bit writes |
|
Osage- Max Input Rxd msg
displayed when 32 chars input to Shared Secret |
|
Power Save Configuration
options missing in Settings |
|
Osage- Status Messages for
802.1X Authenticatio not as per Osage UI spec |
|
softkeys disappear after blind
directory transfer |
|
TNP- keyboard I/O errors on
reset |
|
RTCP- Exiting Hoot & Holler
cause phone to send bogus BYE packet |
|
7931- Exception in
OverviewModel during restart |
|
Support G.722 56k and 48k in
the Audio Server |
|
TNP phone logs "Unable to
get memory" message on console |
|
pressing volume key then
speaker button can lock up phone |
|
G.722 K-Factor Table incorrect |
|
Highlighted Call isn't
displayed if 10th call ended leaving 9 held calls |
|
7970/7961- dtmf burst is played
with a double duration |
|
Phone does not send un-register
message to SRST on fallback to CCM |
|
7931- Pressing Line button does
not change Line focus |
|
Onhook dialing produces delay
in feedback sound with last digit |
|
IP phone fails to do HTTP
authentication |
|
7931- Overview not in home
position at initial bootup |
|
RTCP socket open error may
cause audioserver to spin |
|
under is only 20 chars instead
of 64 |
|
Dynamic Trace level
registration results in file create/delete operation |
|
EAP-Request/MD5 to PC supplicant
could not pass thru Gig phone |
|
Static Analysis Codebase
Cleaning on Select Files |
|
7961 phones not processing CTI
request to disable softkey |
|
TNP- dhcpRcv.c - uninitialized
variable |
|
7970- Phone lock up when
message URL has max or 255 character |
|
IP Phone should re-DHCP
immediately after DHCP NAK |
|
7931- scroll up and down,
sometimes a leftover icon appear next to label |
|
show inventory command returns
no data |
|
RTCP- SDES packets are not
being padded correctly |
|
Idle Prompt for SRST cannot be
set back to the default value |
|
Phone not sending DHCP traffic
to pc port |
|
Unable to dial from external
dir list after cancel edit dial |
|
LCD display does not always
show status of 3 consecutive lines |
|
7911G experiences loss of
registration |
|
SIP phone show
"Connected" in call preservation if user in/out line disp |
|
7961 with voice vlan resets if
IPC is connected to 3rd vendor switch |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Ringing phone ICON keep showing
up on the phone display without call |
|
Skittles- Retain Dialplan from
CCM while failing over to SRST |
|
IP phone not direct HTTP
request to proxy server w/ unresolved DNS name |
|
Phone does not have "End
Option" field with DHCP Release message |
|
RTP Tx URI request should be
rejected when a call is active |
|
goped won't autoscroll to
previous line/call in multiline scenarios |
|
3rd gen phones running
8.0(4)SR1 unable to adjust ringer after a call |
|
When uri is not responded by
user, second uri post just hangs forever |
|
Clean up debug options
available / messages |
|
Line DN label appear to be
shifted a pixel or two to the left on Display |
|
Digit tone improperly continues
until call connect |
|
JPN hone freeze at Cisco Logo
after reset due to Java OutOfMemory error. |
|
7961/70 fail to transfer a call
with line 2 from Directory |
|
TNP- Remove NULL term from
hostname in DHCP request |
|
7971 displays "Ethernet
Disconnected" briefly |
|
Phone core dump when
terminating mulitple calls |
|
phone not fallback to CCM and
shows "Restarting...". |
|
Enumeration Pattern Code Update |
|
Mute Button is enabled when
Phone Speaker Button throws Error pass Limit |
|
On turbo the overview is
distorted when a new call is created and ended. |
|
Osage- Transaction Status does
not update unless menu is re-entered |
|
TNP SIP phone uses wrong
default TLS port number |
|
Handsfree Receive Frequency
Response does not meet the mask |
|
debugsh- set LOG_DEBUG trace
level for sunvm.cnuw/ debug SIP/JVM command |
|
Phone does not detect Invalid
Load Server IP address for "A.B.C D" |
|
Phone Ringsin Continuously,Need
to power off/on to clear the call |
|
7911 SLR is 5 dB softer than
required, its ok in GL mode |
|
IPPM- Phone displays XML Parse
Error when accessing Contact List |
|
7961 - PC cannot see data
traffic if PC Voice VLAN Access is disabled |
|
TNP SIP phone can not handle long
Unicode callid/linetext |
|
7931- Clean up OverviewModel
ACTIVATE_REQUEST event handler |
|
7970 Runs out of memory as
phone when idle URL is used |
|
7931- Phone looses softkeys when
exit from IDLE URL screen |
|
Incorrect values in
RX/TX_START_TIME and/or REPORT_TIME pegs |
|
Soft factory reset does not
clean files from /etc/sfr.tab |
|
RTCP- With RTCP disabled web
StreamingStats Report Times are invalid |
|
Include Kernel.core into the
sylog files for debug purpose |
|
Not able to use Dial Sofkey in
Corporate Directory |
|
TCP not sending all posted data
after socket close |
|
7911/41/61/70/71 - 2 concurrent
XML posts result in Error 0 or Error 6 |
|
devoplement build (TNP) script
does not work |
|
Dial Softkey should be disabled
for corporate directory/PAB/FastDials |
|
Turbo- DoS tool icmpsic crahses
phone on Bugtrap 0x93 |
|
Unmount Error |
|
HTTP sessions are not currently
aged-out |
|
CreateStringMatchProperty does
not update the allowedValues |
|
TNP - 7911 phone needs an
802.1X port lookup mechanism |
|
9 lines with call in Hold
Reversion, phone stops ringing |
|
provide for next generation
static analysis for TNP |
|
RTCP- BYE packet has padding
bit mistakenly set |
|
7941/7961/7970/7971 Aliasing in
high band when using wideband headset |
|
7931- LineFullDisplay detail is
missing from the title |
|
Call History Enhancements for
Chumbawamba Phase 1 |
|
7970- reduce msg sizes being
used in network daemon IPC |
|
Static Analysis Codebase
Cleaning on Select Files |
|
When calls are
selected/unselected, sorting is done immediately |
|
TNP - 7971G-GE forwards 802.1X
packets twice |
|
Exit softkey stops UI when in
Security Configuraiton/CTL File submenu |
|
7931- May have a Java Memory
leak in disposeDynamicFeature |
|
Static Analysis Codebase
Cleaning on Select Files |
|
IP phone stuck at Cisco Logo
screen when reset from CCM w/ sidecar |
|
Can not login to phone during
automation testing |
|
support persistent status line
display on SIP phone in SRST mode |
|
Phone throws exception upon
going off-hook |
|
Dial URI w/ Active Call doesn't
Invoke Call Options when no app in focus |
|
Static Analysis Codebase
Cleaning on Select Files |
|
7931 Titles in Line FullDisplay
aren't left aligned at at the same place |
|
Phone continues to ring after
shared line picks up a transfered call |
|
mipspacker not use CNU
versioning for BN2 image |
|
7931- Line number overlayed
with ellipses ... while in active call |
|
7970 SCCP requires
Authorization when hitting **# to unlock the phone |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Phone Service unavailability
message corrupted |
|
UDI Time Zone not displaying
string from phone config file |
|
7931- Handsfree RLR does not
meet the spec |
|
Phone not showing
"Duplicate IP Adress" in status line |
|
HOST Field Send IP Address
Instead of Defined Hostname |
|
7911 Phone speed and duplex
settings not saved |
|
CP-7971 does not cache TFTP
address if option 66 set TFTP server name. |
|
TNP phone sends
StationSubscriptionStatReqMessage at restart |
|
Focus changes to the new
ringing call before 10 secs.. |
|
Reset on sleep mode phone would
not put it back to sleep mode |
|
CiscoIPPhoneDirectory/DirectoryEntry/Name
should be restricted to 32 cha |
|
TNP- check return value when
writing dhcp.conf |
|
Remote in use calls with no
caller ID should display "To Unknown Number" |
|
Sanity- Core produced for rtsp
on restriciting incoming bandwidth/bitrat |
|
Fragile file cleanup and
performance enhancements (Jasmine featurette) |
|
7931- Tuk Tuk noise heard while
using wideband codec for a call |
|
7970 Phones have incorrect
active display during shared line call |
|
SIP phone should reattempt
download of softkey&dp on TFTP down/ timeout |
|
For Cbarge "CM
down,features disabled" message not displaying on 7970 |
|
7931- Headset icon not
displayed when Headset LED is pressed |
|
Expand Directory object name
field to accept 64 characters |
|
7931- Softkeys disappear with 4
sofkey templates |
|
7971 should set Audio
Preference to default values after Erase |
|
Muffled voice on receive for
some calls |
|
cnu recover second look |
|
7911- GroupPickUp does not work |
|
Unknown name displayed if
special characters are in display name |
|
7970-DHCP- Rejects DHCP request
with option 15 from CNR |
|
Display on shared-lines
not-in-call is not consistent in cBarge scenario |
|
7931- Incorrect call appearance
on shared trunk monitor calls. |
|
Call Focus shifts to Held call
for consultative conference call leg |
|
TNP - Soft factory reset should
clear 802.1X PAE info |
|
7931- Enable video support |
|
Focus is on wrong call when
line view is opened indirectly |
|
Change the 7906 BN2 to use
RELEASE keys for pilot build |
|
Turbo should not advertise
G.722 |
|
Dynamic features like BLF Speed
dial and Privacy are not working |
|
Call fails when no dialplan and
registered to SRST |
|
Conference on Alerting with 8-0-2-4S
load |
|
Update 7911 diagnostics to
version 10.02.00.06 |
|
CNU kernel BugTrap 0x91 with
V-E-R-Y specific conditions |
|
TNP phone stuck in blank screen
during upgrade to 8.0(3) load |
|
third-gen phone 8.2(1) recover
process is not displayed |
|
dsp ingress frame timestamp not
following RTP RFC3550 |
|
sleep() system call not POSIX
compliant |
|
AbbrDial key shouldnot be
active when speakerbutton is disabled |
|
Text Item Displays are not
right justified in RTL locales |
|
Phone should explicitly turn on
display when reset/lost registration |
|
SIP phones should Ignore
unknown softkey set names in softkey xml |
|
7931- Add icons to the
DetailsFullDisplay |
|
CIA-680 Support on 3rd gen
phones |
|
revertPriority setting not used
for 1st call after changing the setting |
|
Third-Gen phones running 8.0(3)
do not hear multicast audio from RTPMRx |
|
8.2 phone load causes robotic
issue at customer site |
|
Dialplan is not supported when
Failover to SRST |
|
Highband noise reduction tuning |
|
Bugtrap 0x91 phones (during
fsck) |
|
unable to disable kpml on TNP
phone registered to CME |
|
TNP- send DISCOVERs if no DHCP
server can be found |
|
IP phone reset with DOS attack |
|
7941/61 LCD controller must be
reset at startup time. |
|
Arabic locale missed QRT on
dest info |
|
Empty Dial list is getting
displayed on phone |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Default router entry removed
when dup ip present |
|
Can not press line 36 on 7970
with 2 sidecars |
|
7931- Unable to answer call on
2nd line using phone handset |
|
"On " prompt doesn't
always work |
|
Static Analysis Codebase
Cleaning on Select Files |
|
TNP- "show inventory"
CLI output not adhering to the specificication |
|
redial sk is not active in
onhook state |
|
getEndPointInfo reports MWI
setting incorrectly |
|
vm -mem broken on Broadcomm platform
(7941/61, 7970/71) 8-2-0-20 |
|
LCD display shows status of Lines
22-24 after phone boots up not 1-3 |
|
Turbo- DHCP recv socket error
on bad address |
|
7961GE stops receiving
EAP-Req/ID during long duration reset test |
|
Static Analysis Codebase
Cleaning on Select Files |
|
7931- Doesn't show IDLE display
on phone display after restart from CME |
|
TNP phone fails to display the
switch info at its webpage |
|
7970-PNG image file download
unexpectedly shutdown the phone |
|
SYN ACK messages from phone not
DSCP tagged |
|
Jphone- Navigate problem under
network statistics menu when debug mode |
|
make property retrieval from
RMS store file effecient |
|
Handsfree SLR does not meet the
spec |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Add volume control for local
and network tone |
|
7931- Speed dial does not
display called-id when another line offhook |
|
Selective graying out of
AudioPref menu items incorrect on inline power |
|
Placed calls are not
multi-party and should not show a MP call history |
|
Phone Continuously displays
"Requesting...". |
|
Softkey wrong after fallback
from SRST |
|
7961 (and 7941,7970,7971)
doesn't display Call park number after getting |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Static Analysis Codebase
Cleaning on Select Files |
|
7931-UI shows lines 22-24 when line
button pressed with AppMenu Open |
|
Settings -> Device
Configuration -> UI Configuration menu is missing |
|
Call History Lists inaccessible
after having max entries and deleting 1 |
|
7931- Phone restart from CM
duration test leads to Disk full |
|
Add SIP related changes to
support G722 for ph0 of wide world |
|
Missing Pixels on the left side
of UI displays on Turbo phones |
|
phones should not advertise
Voice VLAN on PC port |
|
JTest- SIPCCAdapter.java switch
statement missing breaks |
|
7931- Factory Reset Walk LED
pattern is only 16 |
|
7971 phone reverts to old
config after changes saved to netwk config |
|
7931- LEDs for lines above 8 do
not illuminate |
|
debugsh should support RTCP
trace |
|
Cfwdall fails to come back on
CCM after fallback from SRST |
|
7914 displays old version of
remote-in-use icon |
|
Line LED not lighting up or
delayed on incoming calls |
|
Phone display not turned on
when going into reverting state |
|
TNP SIP Phone resets after auto
register due to default load info missin |
|
PNG Broken- Phone fails HTTP
GET if earlier HTTP request is not finished |
|
Pushing RTPRx or RTPMRx URI to
phone in a call enables mute |
|
Call Statistics menu- Sender
size is not a correct format |
|
SIP phone UI Locks up and
Keypresses ignored (still registered w/ CCM) |
|
UI locks up & phone cannot
register |
|
Timer Exception seen in
TimeDateRequest |
|
Clear softkey does not work in
Status messages screen |
|
Outgoing ringing and incoming
ringing tones played at same time |
|
apply patch for Diab compiler
from WindRiver |
|
Add new tone messages to make
traditional/stutter tones selectable |
|
Phone accepting duplicate IP |
|
Static Analysis Codebase
Cleaning on Select Files |
|
7911, 7906,7931 & 7921 have
poor voice quality with G711alaw codec |
|
Out of Memory - Connection
refused errors after duration testing |
|
Turbo- 1st incoming call can't
be answer if 2nd one be connected first |
|
RTCP- RR/SR packet is missing
some info when there is 2 report blocks |
|
SIP gives different Error
message than SCCP in Locations scenario |
|
7931- IDLE URL Refresh timer
doesn't work in 66DEV image |
|
Shared line display & going
offhook while in active call distort display |
|
Write to the TNETV105x PCNTRL
"Access Control Reg" must be 16 bit |
|
TNP- libcso.map from build
should be saved |
|
New Features - Auto Call Select
and More Key Timer |
|
7931- Leave 1 pixel space
w.r.t. App Menu/Headset/etc |
|
Line reports as unregistered,
but it's not, after failover |
|
Re-sync tone table if dsp host
re-starts |
|
Phone core dump while running
the call features automation script |
|
Phone not retrying the re-IP
after dup IP |
|
7961/41 Speaker LED on even
after pushing End key |
|
SETTINGS softkey does not work
if no DHCP server available during bootup |
|
mount command exiting with
status code 64 |
|
KATE Input causes NPE and
non-password data while using XML services |
|
u7961/41/70 stuck at requesting
after phones inbound web access disabled |
|
SCCP phone does not register
back to publisher after restart. |
|
Need an API to assign a local
port to TLS connect |
|
LineModel dispose call throwing
a ClassCastException |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Dialer does not close correctly
after Cancel or Idle Timer Expires |
|
Need filter coeficients for
headset, handset and speakerphone |
|
Static Analysis Codebase
Cleaning on Select Files |
|
Multi-Party Call History -
Transfer case - Received call "from" details |
|
Audio Server K-Factor table for
G.722 |
|
CNU Flash Filesystem not
recoverable if it fills up |
|
certcnu.bin
failure- GETCNU- CNU image update failure; code = 10 |
|
Status of BLF SpeedDial does
not get updated. |
|
need feature parity between sip
and sccp phone for speed-dial |
|
Endcall softkey doesn't work in
Call Preservation |
|
Answer and DnD Softkeys are not
always displayed when a call is rcvd |
|
softkey disappears on the phone
after several calls are made |
|
7970 precedence call waiting
tone does not stop |
|
Issue with Pegs when the call
is remotely held and on MOH |
|
wrong filepath used after
posting a TFTP file |
|
Phone should send the 433
Anonymity Disallowed for anonymous calls |
|
Diagnostic is alway reloaded
into the primary slot |
|
Turbo- Speed dial entries not
at designated position |
|
Calling/Called Info not correct
for SIP TNP phones |
|
Double call sort after ending
selected call |
|
ccmuser- add IIS monitor
similar to ccmadmin, ccmcip |
|
Can't update phones in cm4.2(3)
when all parameters are field |
|
can't update phones in cm4.2(3)
- urlscan reject maxquery string exceed |
|
Media Layer Does Not Correctly
Establish MasterSlaveDetermination |
|
Transfer to busy user causes
Unity port hang |
|
MGCP BRI 3.1 Khz Support |
|
Adding 8.2(1) features to CCM
3.3, 4.1, 4.2, 5.0 |
|
SW MTP/CRA RTP timestamp resets
without SSRC changing |
|
SIP Trunk w/o MTP to H.323
w/OFS results in no TCS and no T38 |
|
CFA failing. |
|
AXL addLine and updateLine
report wrong error |
|
Callback fails / unreliable
when Publisher is down. |
|
CCM releases the call when it
receives Status in call_received7 state |
|
NewCall and EndCall should not
be mandatory softkeys |
|
BARS not updating CCM03xx DB
name in Monitor Disk Space job on Restore |
6608
6608 MTP port intermittently
unregistered |
|
6608 T1 CAS ports are getting
marked as OOS |
|
6608- Cleanup code to make room
for few more fixes |
|
6608- debug enhancements |
|
6608 Gateway gets unregistered
after resetting MGCP Backhaul port 2428 |
|
6608 shows wrong OID |
|
COLP not present over SCCP --
H323 ICT -- SCCP |
|
Overlap Sending broken when
using redial function while phone is onhook |
|
SDL version change for fix of
CSCsf32240 |
|
CCM reporting encodingStyle as
ISO-8859-1 instead of an http URL |
|
Dead air for calls that are not
processed by application. |
|
CCM service unexpectedly
shutdown - access violation |
|
CM 4.1(3) stops Multicast-MOH
after receiving an ICMP Dest Unreachable |
|
CCMSNMP does not start on
subsriber when publisher is down |
|
Add retry DB Sanity test logic
in CCM SNMP agent during initialization |
|
JTAPI CiscoTransferStartEv
anomaly when transferring a call to a CTIRout |
|
Address type not updated when
JTAPI receives CallPartyInfoChangedEvent |
6608 E1/T1
6608 T1 cas channel rejects
outbound calls |
|
ccm core when QSIG-tunneled ICT
call is disconnected by remote side. |
|
CCM4.1(3)ES. SQL error when
inserting a 7961 phone |
4.1(3)es72 (Base for 4.1(3)sr4d & sr4b)
RTMT does not work on winos
2000.4.3a or 4.3SR1 |
|
Media Layer Does Not Correctly
Establish MasterSlaveDetermination |
|
Meet Me Conference is released
when CallManager is down. |
|
Callmanager Fails To Remove
First Call Leg During Blind Transfer |
|
CTI shall unregister ssmanager,
then register ssmanager at failover time |
|
update/add Phone do not allow
userLocale/networkLocale for Cisco7920. |
|
CTIProvider is not closed when
WebDialer is deactivated |
|
Jphone software changes to
address Memorex enhancements in EDCS-505798 |
|
Support RTCP featurette |
|
Add nightlight features |
|
MGCP GW reset due to message
order changed |
|
CCM.exe process shows very high
memory usage |
|
callmanager generate same
confernceID for h323 gateway call |
|
15 seconds delay when using
speeddial for forwarding from AC |
|
JTAPI modified calling party
number overwrtten at Route List |
|
SIP trunk stuck in a
Shutting_Down state can not be reset |
|
beeps for CFwdAll confirmation and cancellation,
7941,7961,7971 |
|
QSIG-ccm.exe unexpectedly
shutdown by overrunning the display[32] buffer |
|
CTI manager running high CPU
with CTIERR_DEVICE_SHUTTING_DOWN errors |
|
listUserByName-Bad search
filter error if no lastName expr given |
|
CCM tears down all calls on
t1-cas trunk if one timeslot reports 5XX err |
|
CtiQbeProviderUnexpected
Shutdown after device unassociated with user |
|
CM sends wrong coding standard
in Progress PI |
|
JTAPI-TransferEnd event
delivered after station/line call cleared |
|
Desktop loses 3rd party call
ctrl after consult xfer- personal call back |
|
DM table out of sync..SCCP
handling of linkOOS |
|
DM table out of sync..Device
manager handling of linkOOS |
|
Maketypes needs run after
Product CSV's added to branch |
|
Add 7921 support files (CSV,
XML, GIF) to CCM |
|
ST-CCM service could not come
up after upgrade |
|
CCM AC-Calls do not come out of
Queue |
|
CCM SIP Local Call Transfer
encounter no audio with 3rd party PBX |
|
UnknownCallerIdFlag is not
checked for calling party number for mgcp |
|
SIP trunk sends two different
invites with the same branch ID |
|
T1-CAS MGCP to CM may fail
inbound calls but work for outbound calls |
|
Blank directory search from
IPMA pages returns 0 users for AD or ND |
|
Removing a line from H.323
device causes CDBLException |
|
Non default device load popup
incorrectly lists multiple 7914 loads |
|
CAR tool is not showing
destination CMR in CDR> Search by User/Extension |
|
First call to MGCP FXS port
fails after CCM service restarts. |
|
Callmanager may get duplicate
entries for same region pair |
|
Redial delayed while SDL
tracing is off |
|
Calls to a MGCP PRI fail from a
H323 device |
|
Blind xfer failure |
|
Call park number is not
displayed after getting a new call |
|
Calls fail when CFAll to a CTI
RP redirects to another CTIRP. |
|
Agent logoff after xfer creates
call on callclosed event. |
|
JTAPI caches invalid Device and
Line Handles |
|
always use prime line = true
-> on hook dial not working |
|
Cdcc sends SsMoveInd to
TransferManager, but ignored due to CSCsc67021 |
|
huntlist hunt option changes do
not take effect until reboot |
|
Reset of MGCP Endpoints in
CallManager causes failure, after 4.1(3)sr3a |
|
Incorrect Redirecting Reason
set to DMS with iDivert to VM |
|
MGCP not passing reason code
from PROGRESS to call control |
|
Device Package installation has
dialog come up in silent mode |
|
Link 'View the User Guide for
your phone' not available for 7961/7941 |
|
Distinctive ring not work when
IP Phone has a active call. |
|
High CPU and Code Yellow on CM
because of new call loop with vg248 |
|
Callback fails / unreliable
when Publisher is down |
|
Calling party number contains
number prefix when forwarded to PSTN |
|
Call from PSTN (DMS-100) to
Cisco CallManager failed due to NOTIFY msg. |
|
KeepAlive Events (3) To Provide
TCP Port Number |
|
Always Route Member not enabled
with AXL addAttendantConsoleHuntGroup |
|
7920 Phone Type reported as
Unknown in TAPI |
|
TCP Port not closed after open
during load test for H323 Calls |
|
MGCP->h323->ipphone call
dropped after 8 seconds of being on hold |
|
CCMUser should use FastAccess
to get locale information |
|
Agent logoff after xfer creates
call on callclosed event. |
|
CM sends Progress message
without PI causing PBX to drop the call |
|
Resource Unavailable cause
releases PSTN call via H.323 Gateway |
|
Wrong cause code when a call
forwarded to Hunt Pilot not answered |
|
CallManager loses CSS for Line
so can't route call |
|
7914 Non-default device load
only displays 1 module |
|
MeetMe conference leak causes
reorder tone on initiating MeetMe |
|
Callmanager won't play re-order
tone for Cause 0x809D Facility rejected |
|
Multiple calls with no ring for
subsequest calls when a call drops |
|
MonitorPartyTable leak causes
continuous appearances of Code Yellow |
|
Add code for RISDC to handle
second DBL Exception |
|
960 One button Login Failure
with @ character in the password |
|
CM Video-VCB Resource counts
not changing for first video participant |
|
CallManager should support
RFC3398, or strip ;npdi |
|
JTAPI Gateway receives
RESOURCE_NOT_AVAILABLE error |
|
Route/Hunt list is not
displaying the correct status. |
|
Synching DBLEnums.asp and .js
from share directory |
|
CCMUser can't delete the
service URL after unsubscribing the service |
|
Make 7906 (turboprop) appear in
device defaults and device pulldown FCS |
|
7906/7911- Checkin user guide
and update CSV files for online user guide |
|
Name ChangeCisco Unified CallManager
4.2 - ES/SR Wrapper |
|
QED (CSV and Display XML file)
Changes for Phase 2 Ocius 7985 |
|
CIA-680 Support on 3rd gen
phones |
|
CCMAdmin should not offer
option of 72XX voice platform as a MGCP GW |
|
Calls to BRI gateway from 2nd
node fail after 1st node CCM is restarted |
|
Decommissioned Server Not
Removed |
|
Intermittently failing to
change CFA number by Netwise application |
|
InsertCDR needs to better
handle deadlock on calldetailrecord |
|
Non default device load popup
does not list load for 7914 |
|
CMR data not being loaded by CAR
consistently - Call QoS shows NA |
|
CAR needs to remove loader
validation for directory number |
|
BAT does not allow entry of 2
line and 4 speed dial if SD are blank |
|
Importing phones into BAT using
a comma in the Alerting Name is invalid |
|
ENU Coltrane3.0 Check In For
English-US Locale |
|
AC_J.out.log fills hard drive
and 100% CPU for tcdsrv.exe |
|
AC call routed to client
remains in queue causing new calls to back up |
|
Transfer fails when forwarded
to CTI ports |
|
fwded calls over QSIG to other
vendor voice mail go to open greeting |
|
Empty CM Group or Device Pool
Insert/Delete Induces CTFTP REBUILD_ALL |
|
multiaccess to CCMAdmin page
cause high memory usage of dllhost. |
|
BAT needs to provide a throttle
mechanism to control CPU usage |
|
RIS need to handle empty
resultset gracefully |
|
CCM 4.1.3 sends
StopMediaTransmission for incorrect MOH unicast stream |
|
AdminUtility display a failure
message when try to set IWAM_GUEST pwd |
|
Product Specific Configuration
Missing from 2821MGCP gateway config page |
|
CTI tries to register notifications
after app terminates unexpectedly |
|
Phones,Gateways dont register
when cnf cache SP is changed-ctftp |
|
DN config page of 7941G-GE
& 7961G-GE shows improper phone icons |
|
7941G-GE & 7961G-GE phone
Icons are not shown properly |
|
Find & List Phones Page
gives HTTP Error 500 after SR Install |
|
H.323 Tandberg not getting MOH
when on hold by SCCP Tandberg |
|
Multiple calls with no ring for
subsequent calls when a call drops |
|
JTAPI error -1932787643 when
Apps is answering a consult call |
|
Call forward busy on remote
node device fails |
|
CM Video Bandwidth Unavailable
shows for trunk calls with sufficient BW |
|
CM Location Resync Bandwidth
option doesn't resync video BW too |
|
TFTP takes too long to act on
the change from Caching to Non-Caching |
|
AXL update of BusyTrigger tag
fails |
|
Number OfJTAPI Traces Is
Limited To 100 |
|
JTAPI doesn't drop
ExternalConnection |
|
Qsig callback and MWI between
clusters are failing |
|
Auto Pickup causes incorrect
connected name on requestor phone display |
|
NumDevRegExceeded- Number of
registered devices exceededPhones cant REG |
|
Forward information is not
displayed in a scenario in QSIG |
|
Forward switch fails if forward
reroute failed due to no route in orig |
|
participant is not removed from
participant list when request rejected |
|
fwded calls over QSIG to other
vendor voice mail go to open greeting |
|
Trailing # should be stripped
from DivertingLegInfo after call routing |
|
CCM reset due to memory access
error in MGCP |
|
Treat auto pickup as a direct
call and display From xxx |
|
Error in DeviceManager table
leads to False Out Of Resources Condition |
|
Notification Indicator Mandatory
IE Missing in DMS NOTFIY message. |
|
After sending ECS, CCM should
send TCS after peer closes its channels |
|
DivertingNr should be converted
to RedirectingNumber |
|
Max value for Forward Max Hop
Count needs to be increased |
|
Delayed cut-through on low bandwidth
pipes with shared lines |
|
ART failure adding user to
admin group due to referral during ldap Add |
|
CFNCExtCallingSearchSpace
shared setting not getting reset to default |
|
AXL listUserByName does not
return user with blank First Name |
|
CCM using Active Dir or
Netscape Dir Svr AXL search returns no matches |
|
AXL addPhone/updatePhone does
not save MLPP Domain value |
|
update/add Phone do not allow
userLocale/networkLocale for Cisco7920. |
|
ITA Display of Zero and CAPS O
- 7960 Font Display |
|
Dash/Underscore is an invalid
char in User Group Base but not for DNS/AD |
|
CCMAdmin page become hung,
iexplore.exe runs at 100% |
|
7911 Add support for Vieo |
|
Placeholder CDETS for Turboprop
Feature Commit |
|
Enabling or disabling of CFA
from IP Phone intermittently fails |
|
7912 Park number is not
displayed for a while |
|
Join with on going dial call
creates extra conf member |
|
hold-state softkey set not
updated on sccp phone in a scenario. |
|
b channels may delay coming in
service on MGCP gateway |
|
MaxHoldDurationTimeout requires
a restart of CCM service |
|
RTMT reports
LowCallManagerHeartBeatRate for all call processing nodes |
|
CDR/CMR Export throws Error if
selected date range do not have CDR/CMR's |
|
Export CDR/CMR not working in
CAR |
|
Traffic Summary - Day of Month
[Monthly] Report is consuming 100% CPU |
|
Incorrect LINE_CALLINFO after
lineAddtoConference |
|
Call is not getting cleared (
keep ringing )at all in Huntlist scenario. |
|
CCM stops generating ring-back
as it gets H245 LC open |
|
Unable to communicate with DCD
when SSL enabled |
|
Some Serviceability Reports are
not generated due to java exception |
|
Cannot create new PAB entries
from IP phone |
|
Can not see the PAB Entry on Search
on Phone for specific Nicknames |
|
Placeholder CDETS for Turboprop
Feature Commit |
|
Call placed via 6608 T1-CAS
failed when extra digit dialed. |
|
Calls to CTI Route Point fail
if CCM group is changed |
|
MLA removes space character
from OU name for AD LDAP access |
|
CCMAdmin IPMA config with AD
fails if directory query time out |
|
CMM Echo Cancel Coverage 8 and
16 ms should be removed |
|
Back out CSCsb60395 change in ConnectionMediaManager |
|
Incorrect 'srcinfo' in
Admission Request from CCM, for forwarded calls |
|
Optimizations for CIPT uses
incorrect ConfigDB |
|
RTMT generates directory
connection and replication alarms |
|
Call transfers over ICT between
clusters ring fast busy of dead air. |
|
E-mail information erased after
PAB entry edited on phone |
|
User unable to edit PAB entry
if nickname crosses 26 character |
|
Unable to allocate PAB entry to
PFD service if nickname is >16 character |
|
Fast dial from an ip phone
7960/7940 fails for 24 digit numbers |
|
unable to add fxs port to a
route group |
|
Trunk Configuration Page
displays productType is 77 below ctrl buttons |
|
Incorrectly versioned CiscoCTL
Client plugin checked in |
|
No DevSpecific event
notifications after losing connection with CTIMgr |
|
MSSQL remains in Starting State |
|
CFNA/CFB External not working
for T1 CAS or BRI loopback calls |
|
CCM send internal conference
bridge number as the connected party number |
|
Calling and called parties were
swapped in CcSetupCompReq and CcSetupRes |
|
No StationOutputStopTone When
Onhook Speeddial Matches Overlap RP |
|
H.323/ICT conf resource not
released when rx empty terminalcapabilityset |
|
CTI unexpectedly shutdown more
then 16 party ad-hoc conf with CTI device/line monitoring |
|
CTL client returns 'No valid
server certificate found' |
|
Transferred calls to ac pilot
are stuck in queue |
|
calls to the AC pilot are being
rejected with available HG members |
|
Call details orphaned in
broadcast queue when transfered from Unity |
|
Intermittent missing TransferEndEv
for some calls |
|
CCM unexpectedly shutdown w/
access violation in SoftkeySetMask--SetSoftkeySet |
|
Calls to the ACPilot get stuck
in queue until manually released |
|
Call to Pilot Point from SIP
trunk fail |
|
Mistreating incoming TCS data
capabilities as video capabilities |
|
Skinny (G729)-CCM-MGCP calls
fail intermittently |
|
CM strips first digit of PRI
DMS Original Called Party Number |
|
Find/List Trunks-Search RP by %
works like IsEmpty |
|
Unable to login IPMA assistant
console |
7940/7960
7960 phone does not clear
status line during reset |
|
pressing line button on ipphone
doesn't switch between detail &overview |
|
Posting Line34 URI enables
Line30 on ip phone. |
|
7960- Does not preserve the
state of mute/spkr button in handset mode |
|
7960 drops the incoming call
when using the IPICS services. |
|
7960 phone does not handle HTTP
code 401 for push request |
|
Phone- Authentication
username/password takes only 31 characters |
|
CiscoIPPhoneInput takes * and #
when input is set to N |
|
StreamingStatisticsX not
backwards compatible |
|
7960- Call being on hold is NOT
sorted by Select function |
|
7960- Doesn't update CDP cache
when no voice vlan present in CDP message |
|
7960 DSP Logging utility broken |
|
7960 does not display via XSI
Object Pass through |
|
IP reassembly broken |
|
IP phones become unregistered
from both SRST and CM |
|
7960/7940 phone stuck at CONFIG
IP after a reset/power cycle |
|
Phone load Upgrade to 7.2(3)
causes RXshort errors on PC port |
|
Phone drops untagged PC Traffic |
|
HTTP 100 Continue from phone
malformed |
|
Remove use of linked directory
in SCCP BA |
|
7960 - XML Debug PUSH behaves
erratically |
|
Handle Current Call missing
when dialing from Directory |
|
Phone rejects menu responses
from server- Fastdial, Corp Dir |
|
Callback notif (Dial) &
Park while already in an active call fails. |
|
GARP enable/disable ignored |
|
The phone unexpectedly shutdown
when it receives invalid Response.ContentType in HTTP |
|
Secure Phones does n't cancel
tftp request while cancel key is pressed |
|
7940/60 PC port 100M does not
receive network traffic intermittently |
|
7960/7940 Rcvr Lost Pkt reports
as a negative no under impairement |
|
Unable to dial the CB notified
number during ringing state |
|
No sidetone during first phone
call following phone registration |
|
Phone performs unneeded ARP
when Garp enabled |
|
Phone removes ARP entries too
quickly |
|
help for settings button not
displayed when setting key is disabled. |
|
DHCP enabled Phone resets with
held call when alternateTFTP changed |
|
Phone doesn't display held call
in detail view when barged call ends |
|
Promts is Truncated to 20 Characters
when using Greek Locale |
|
Phone resets if we dial Half of
the DN on-hook & remaining off-hook |
|
Speed dial from Monitor DN is
not working with 7.2.2 |
|
phone display Remote-In-Use
menu when the other end resume the call |
|
DIALED Number missing in CFA where
the target phone is 7940/60 SCCP |
|
Update 7960 built-in font to
include new zero with a slash |
|
7960/40 cannot register in
autheticated mode CCM 4.1.X OS 2000.4.2 |
|
Phone resets during high
bandwidth traffic to PC |
|
Placed calls are recorded on
all shared line phones |
|
Missing SpeedDials on phone
after upgrading the phoneload |
|
7960 unexpectedly shutdown when
more than 20 calls placed via stress script |
|
Placed call list under directory
gets updated only for Connected calls |
|
7960- Unable to reset phone
when other shared line is busy |
|
Phone strip dialed Number in
Directory Placed call list for PSTN call |
|
Phone without DHCP cant recover
Dup IP address |
|
7960/7940 characters by pressing '0'
with li-ffr.4-1-3-JPN are funny. |
|
help symbol missing in text
press - key to cancel for english locale |
|
7960 Settings -> RingType
menu changes doesn't take effect |
|
7910 DSCP values need to be
consistent with current design guides |
|
EM logout restarts the IP
Phone. |
|
Small MTU causes CVTA to H323
video call failure |
|
7960/7914 Ringer type off by 4
lines. |
|
Update dictionary file with
SeaDragon new phrases |
|
Phone Continuously displays
Requesting RingList File ...... |
|
Phone UI Lines separating the
DN disappear as it failover to subscriber |
|
http///CGI/CallInfo does n't
display all lines call Info. |
|
ActiveSoftkeys eg redial, New Call
are shown when pubisher CCM is down. |
|
In CallInfo the CalledPartyName
field is not proper for Conf call |
|
In http request for
CallInfo/LineInfo the Prompt field is showing null |
|
Line button does not answer
call with 2 calls on hold already on line |
|
DHCPReleaseMessage should be
unicast to DHCPserver,not on broadcast IP. |
|
7960 Phone doesn't display
blank URL sign or URL without label on line |
|
Volume control keys when
calling a busy no affects ringer(ver8.0(0.16)) |
|
7960 Phone reset from settings
with **#** while on call hold |
|
7960 Phone loose RTP stream
when restart from CM |
|
7960 Pressing Line button twice
ends calls on Phone in ringing state |
|
BigApp does not kick back to LA
on version mismatch in XMLDefault.cnf.xm |
|
phone 7940/7960 should escape
'#' symbol |
|
7960 doesn't receive MOH or
DHCP when Voice VLAN = Access VLAN |
|
RED LAMP indication on 7914 for
In Use Remotely does not work - 7.2(3) |
|
7960 MWI functionality should
be consistent with current phone behavior |
|
7960 Phone volume not being set
properly at RTPRx start |
|
Menu object as IDL URL, menu
item 1 selected when phone goes off-hook |
|
MWI lamp glows continuosly after
a CB notification for the first set CB |
|
IP phones become unregistered
from both SRST and CM |
|
Phone drops untagged PC Traffic |
|
Secure Phones does n't cancel
tftp request while cancel key is pressed |
|
7940/60 PC port 100M does not
receive network traffic intermittently |
|
Unable to dial the CB notified
number during ringing state |
7914
Implement 5.1 features |
7985
The phone does not honor the
Connection Monitor Duration fallback value |
|
Phone may malfunction if more than
two lines configured. |
|
Telnet xstatus command under
DNS/Domain Name contains non-ascii letters |
|
Need to add support for IP
phone service |
|
IPMA is not supported with 7985
video phone |
|
Add screen saver to 7985 |
|
XML support |
|
Three or more line appearance
needed |
|
Ocius should have a contrast
and white balance configuration options |
|
save button placement cause
user to end call |
|
Directories menu does not
display for 15 seconds when URL is unavailable |
|
Background image support is
required |
|
Phone unexpectedly shutdown
when 100 calls active and remote side is lost |
|
7985 does not play the MLPP
premption tone |
|
Settings Erase softkey is
displayed even when config is locked |
|
7985 video endpoints do not
support services. |
|
Packets from the PC port are
not being forwarded out SW port |
|
7985 unexpectedly shutdown when
attempting to originate a call from WebDialer |
|
Phone does not ring at all if
the selected ring tone is not available |
|
Error message on missing ring
tone is different than 7970 |
|
Phone never boots up when
background image is changed |
|
Phone does not detect changes
to the CM background image list file |
|
7985 does not do Authentication
for CiscoIPExecute |
|
7985- HTTP redirect not work |
|
7985- CiscpIPPhoneIconMenu
oject parse error |
|
7985- HTTP refresh not work |
|
7985- two items missing from
phone's web access page |
|
7985 not display Authentication
URL on Device Configuraiton menu |
|
7985 should have Power Save
Configuration menu |
|
Device ID in CDP messages
should all be in upper case |
|
7985 takes too long to
re-register when image load is not found |
|
7985 not back to power save
mode if restarted from CCM |
|
Alpha Numeric fields use
different key mappings than other phones |
|
7985 not back to power save
mode after a call coming in |
|
7985- phase 2 image does not
support asp URL pushed to the phone |
|
7985 should exit Service app
after login w/ ExtensionMobility |
|
7985 (X) button toggles between
Full Screen and Overlay modes |
|
7985 only shows 6 lines w/ Privacy
and Speedial configured |
|
7985 does not display To
conference at line button menu |
|
Callback activation tone is not
heard when using TFTP Server 2 |
|
7985 not registered to its CCMs |
|
7985 not update call status
icon at line button menu |
|
Hanging up the phone does not
work when failover occurs during call |
|
7985 unexpectedly shutdown when
Execute Object is pushed to phone with proxy config |
|
7985 got authentication error |
|
7985 can not list PAB entry |
|
7985 displays white line at
full screen |
|
7985 does not send out video
packets w/ IPMA configured |
|
There is no Cancel softkey when
requesting a phone service |
|
Berbee services do not work on
7985 |
|
Softkeys in the Berbee phone
service do not work properly |
|
MyGroup IP service returns back
John Chambers' group instead |
|
7985 should exit from Setting
menu by pressing Setting button |
|
7985 Error message different
when URL DNS name error |
|
7985 unexpectedly shutdown when
wake up from power save mode |
|
7985 incorrect behavior when
get HTTP Error 404 |
|
Camera Properties need a wider
range of changes |
|
When upgrading the software the
status line is stuck |
|
Left/Right arrows should change
the monitor brightness values |
|
7985 could not display FastDial
page |
|
7985 Update at service page
does not work |
|
Phone unexpectedly shutdown
while looking at the eventlog during an active call |
|
Video between 7985s momentarily
blurs out |
|
7985 unexpectedly shutdown
while answering a call |
|
Remote side video stops working
when hold/resume rapidly pressed |
|
7985 should close the listening
chanel when service app is closed |
|
Exit an IP phone service
returns the user to the top of the service list |
|
Phone takes DHCP option 150 in
the wrong order |
|
Conference call info status is
displayed as the the 4 instead |
|
Digits after first call state
softkeys are messed up |
|
Calls for status line is
corrupted after pressing directories button |
|
The From status line displays
no number on an incoming call |
|
Call Park doesn't display the number
parked at |
|
Phone should drop from full
screen mode during an incoming call |
|
7985 Push Execute failed with
Internal Error |
|
7985 unexpectedly shutdown w/
call on hold |
|
7985 does not disable SSH after
reset |
|
985 fails over to SRST after
ethernet cable replugged in |
|
7985 does not change Camera
properties back to default value |
|
7985 should not display Erase key
at CameraSettings menu |
|
7985 plays wrong Ring Tone |
|
7985 does not save selected
Ring Tone if RingList.xml not available |
|
HELP ID- Help for Camera
Settings returns help for Monitor Brightness |
|
HELP ID- Brightness Hue Saturation
help returns main help topics instead |
|
7985 set button template wrong
w/ one button set as None |
|
7985 unexpectedly shutdown when
access Help Main menu |
|
7985 fails to display Video
Mute icon when incoming call answered |
|
Video mute line status icon is
lost after a hold/resume |
|
Placed Calls Directory entries
have a %s as part of the display |
|
Background & Ring don't
reset when Restore Default Settings is involked |
|
Downloaded Background &
Ring list missing when TFTP Server 1 is down |
|
7985 unexpectedly shutdown when
Line key pressed on Help Menu |
|
X button does not work in
Service w/ Host Not Found Error |
|
No Help Info for Transfer
softkey |
|
No Help Info for NewCall
softkey |
|
No Help Info for More softkey
in onhook state |
|
No Help info for Dial and
Cancel softkeys in onhook dialing state |
|
No Help Info for NewCall
sofktey in Remote-In-Use mode |
|
Softkey sets mess up after
access Help in Callback mode |
|
No Help info for ImmDV and
TrnVM softkey in ringin state |
|
7985 should include Camera
Setting info on View Setting menu |
|
Forwarded to status message not
display the DN |
|
7985 displays ?1001 status
message when in Setting menu |
|
X New Missed Calls should not
persist w/ new incoming call |
|
7985 does not support
Restricted Setting Access |
|
Phone unexpectedly shutdown
pressing the Search softkey on Corporate Directory |
|
Next softkey does not work in
Corporate Directory |
|
Wrong softkeys when looking at
an empty Missed Calls list |
|
Cancel softkey has no impact
while downloading Background images |
|
7985 play ringer to handset for
a second call |
|
Softkeys disabled after change
audio source w/ Handset off the crack |
|
Forwarded Call Infomation
Display not as configured |
|
Softkey sets changed after
pressing Line button |
|
7985 should switch back to the
first call after 2nd disconnected |
|
7985 behavior inconsistant with
2nd incoming call |
|
Wrong softkey sets for barged
call |
|
7985 displays Remote-In-Use
icon after barge into a call |
|
First ring tone in ring tone
list is the letter a |
|
Cannot easily answer incoming
call while in Missed Calls Directory menu |
|
7985 call status message mess
up for shared line |
|
7985 shared line Call Info
display different from other phones |
|
7985 should initiate a new call
on shared line by selecting the line |
|
7985 not show the CallInfo of
shared line on line menu |
|
Dial key not work on FastDial |
|
7985 should always use first
avail. line for Dial from Directory |
|
7985 should allow number with
25 digits at PAB |
|
7985 not fallback to primary
CCM if the CCM restarted |
|
7985 does not have Next Softkey
at Berbee main menu |
|
No Update softkey for
graphicMenu and image |
|
7985 not work with
directory.asp |
|
7985 fails to display No Park
Number Available |
|
PAB service URL does not work |
|
ExtensionMobility ServiceURL
button not work |
|
IP Phone service - My Group
does not work properly |
|
7985 flash light not blinking
for Callback |
|
Denial of Service tcpsic script
unexpectedly shutdown the 7985 |
|
Personal Address Book edit Name
returns 400- Bad Request |
|
7985 not display Softkeys with
position more than 5 |
|
7985 could not display
Directory object with maximium value |
|
7985 unexpectedly shutdown when
pressing Softkey-Next and Softkey-OK |
|
Phone does not recoginize
SoftKeyItem/Position object |
|
7985 gives parsing error with
IP Phone Agent Service |
|
7985 unexpectedly shutdown when
running a image slide show IP service for 10 minutes |
|
Fast Dial phone service should
be allowed to Assign up to 32 digits |
|
Call Information is not
displayed after pressing Settings button twice |
|
7985 gives incorrect Error Code
for XML parsing error |
|
Phone help does not work |
|
7985 gives ParseError if IPMA
realtime update stopped |
|
7985 unexpectedly shutdown when
press Exit at IPMA assistant service |
|
7985 does not display Exit key
w/ Parsing Error |
|
Phone does not fallback off SRST
router after call is terminated |
|
7985 unexpectedly shutdown when
attacked with some Denial of Service scripts |
|
Phone displays a ? instead of
line feed on directory listing output |
|
Blackjack IP phone service
returns error after 1st key press |
|
IPPA service Agent Login screen
password entry is displayed in the clear |
|
Phone directs some http
requests to the proxy url when it should not |
|
PC Voice VLAN disabled does not
work |
|
Line button not work if not all
line buttons are assigned |
|
7985 should change focus to the
active call after exit from Setting menu |
|
No Help ID for IPMA related
softkeys |
|
Softkeys are confusing when in
the Lines menu |
|
Cannot hang up a call when the
call comes from a shared line |
|
IPPA service briefly displays
some XML code during start or state change |
|
7985 unexpectedly shutdown with
broadcast traffic at Voice Vlan |
|
HELP ID- Background Image help
returns Help Topics instead |
|
One way video or black screen
or no video over VPN observed |
|
7985 XML input - Uppercase
& Lowercase input types allow invalid chars |
|
7985 XML Input - Some Input
types with password field flag show password |
|
7985 XML Input - Equation type
input doesn't allow symbols |
|
7985 should exit from Service
app by Exit key w/ EM login page |
|
Could NOT hangup call on shared
line after restart |
|
7985 New HW does not suppress
upstream Broadcast, multicast traffic |
|
7985 video phone unexpectedly
shutdown when it receives cisco gateway fax NSE |
|
QED (CSV and Display XML file)
Changes for Phase 2 Ocius 7985 |
|
7985 not support softkeyitem as
Key-KeyPad |
|
Berbee IP phone service
returns- unable to display service error |
|
7985 should not clear Status
object |
|
7985 should not append its
Devicename in HTTP Get messsage |
|
Softkeys under the settings
menu are misaligned |
|
Phone status log should contain
more information |
|
One way video seen on call
between 7985s |
|
Ringing stops playing when the
volume is adjusted during incoming call |
|
Phone is using the callback
tone as a ring tone on next call |
|
7985 reboots if Option 150 is a
String Data-Type |
|
7985 XML Input - equals
character (=) looks like a solid, heavy dash |
|
Audio sources do not work on
next call after a failover with call active |
|
Cannot change audio output
source when failover with active call occurs |
|
Error message is truncated when
invalid Admin VLAN is entered |
|
Localization needs to be turned
off on the phone |
|
Softkeys are unavailable after
pressing the Window button |
|
Help for Power Save
Configuration returns help for Camera Settings |
|
Help within the Power Save
Configuration returns Main Menu Help instead |
|
Help of SW Port Configuration
returns help for PC Port Configuration |
|
Stock quote IP phone service
unexpectedly shutdown the phone |
|
Domain name cannot be entered
when phone doesn't have an IP address |
|
HELP ID- Power save
configuration returns help for Display On |
|
Network Configuation Default softkey
should be renamed to Erase |
|
User Preferences Default
softkey should be only available when unlocked |
|
The popup window after pressing
Default should be more specific |
|
7985 - Power save exits XML
Service (and menus) |
|
Configuration parameters domain
name and DNS servers lost after upgrade |
|
Phone rebooted when using Hoot
& Holler with 2 phones in Shout mode |
|
Phone ignores DHCP option 150
when option 66 is present for TFTP server |
|
Domain Name shows up as - ?
when it is not populated by DHCP |
|
Onhook dialing does not light
Speaker LED in SRST mode |
|
On help button ? page, Back
softkey doesn't work |
|
Requesting better
administration tools |
|
Video pixelation on calls made
between Cisco VT Advantage and 7985 |
|
7985 Improper system message
wording |
|
There were no tones heard when
using onhook dialing |
|
No notification on phone when
the remote end of a call is lost |
|
Call focus switches off active
call when shared line is used by others |
|
Default router field
periodically resets when phone is configured |
|
7895 may report multiple
Standby CCMs after fallback |
|
Phone does not ignore lower
valued Voice VLAN when multiple CDPs recvd |
|
Phone may stop ringing when switching
to a second incoming call |
|
Headset mode sends output to
the Speaker in SRST mode |
|
Sometimes cannot answer 2nd
call by switching lines in SRST mode |
|
Phone sometimes does not direct
audio to the handset in SRST mode |
|
Call Forward icon still
displays when fallback to SRST mode occurs |
|
When using EditDial of a number
the prompt should start at the beginning |
|
Rarely the MWI light is on even
when no messages are pending |
|
Phone does not send periodic
CNG packets during long silence breaks |
|
Call Waiting Ring setting will
only Flash the MWI lamp during 2nd call |
|
Video may freeze at end of call
or in self-view mode |
|
Switch should ignore PC Voice
VLAN Access when there is no voice VLAN |
|
802.1p frames dropped on phone
with Admin VLAN and PC voice VLAN disable |
|
Phone gets stuck in CallManager
Unavailable state |
|
Test script causes a watchdog
timer expiration |
|
Packets to PC port are
re-mapped with 802.1p when Voice VLAN is 802.1p |
|
EditDial followed by lifting handset
will not dial call |
|
Phone may continue to display
Self View rather than idle screen |
|
Denial of Service mutant script
cause the phone to reset |
|
Sometimes phone cannot end call
after a CCM fallback with call active |
|
Web Access Enabled/Disabled
need to be added to CCM and phone |
|
Phone sometimes does not
connect to correct backup CCM during fallback |
|
Phone does not reset when lower
numbered Native VLAN learned |
|
Video mute state get out of sync
after the phone is restarted |
|
Phone sometimes shows wrong
status msg/softkeys after CM service restart |
|
Cannot browse under Directory,
Up/D rocker stuck at the Missed Calls |
|
Phone drops ~50% of IP
multicast traffic from SW to PC port |
|
7985 MWI Light misbehavior |
|
7985g reboots after select
softkey then hit the X key |
|
7985 does not play precedence
call waiting tone |
|
7985 phone does not display
call pickup visual alerts |
|
7985 unexpectedly shutdown when
running Codenomicon TCP protocol verification suite |
|
7985 phone reboots when
pressing the 'Directories' or '?' buttons |
|
CCM4.2 - Cisco 7985 Phone
softkeys disappear during Pickup Audio Alert |
7906/7911
7906/7911 Check in 7906/11 f/w
load to CCM |
7935/7936
DTMF tone will not play for
consecutive same digits with 7936 |
7920
Coltrane 3.0 Firmware Check-In |
Digital Access WS-X6608
6608 Incorrect marking DSCP
value to 0 |
|
6608 shld not automatically clr
connection when ICMP unreachable is rcvd |
7935/7936
Cannot use # or * as first
entry while onhook |
|
7936 vulnerable to ICMP attacks |
|
7936 doesn't send HTTP Get with
multi tier DNS names in Directory URL |
|
Can't place a call from phone
book when it receives a missed call |
|
Phone cannot be reset to
factory default when Admin passwd is not known |
|
Remote party hears echo when
7936 used in glass conference room |
|
7936 accepts invalid IP Address
and Subnet mask |
|
7936 accepts invalid
Alternative TFTP Address |
|
Access Admin Setup without
entering the passcode |
|
Web interface allows to change
password with different characters |
|
7936 Web Interface allows different
characters in Phone Book |
|
7936 Web interface doesn't
prompt for password when phone is restarted. |
|
7936 phone retains the meetme
session even after the call manager fails |
|
phone may not give Error tone
when incorrect phone number dialed |
|
7936 Editing phone Book doesn't
have the asterisk in the required field |
|
If call received while editing
ring tone and publisher fails, 7936 hangs |
|
7936 Web interface accepts
alphabets in PING |
|
Phone will not accept incoming
call while waiting for Ping response |
|
7936 Takes long time to
register when PINGED with CCM failover |
|
Info for Http Port parameter on
7936 web page doesn't show port range. |
|
Polycom 7936 allows to change
the Ringer settings in Ringing state |
|
Phone book entry on the web
display is not proper |
|
7936 reboots when you configure
Admin VLAN id while in active call |
|
7936-Call Transfer number is
not displaying in SRST mode |
|
Park Information retained for a
long time. |
|
DN not displayed while placing
the call on hold & initiating a new call |
|
Call initiations fails from the
phonebook with CFwdAll |
|
Phone registers with Alt TFTP
when Alt TFTP Address not specified. |
|
Phone hangs when used
Diagnostics with CCM failover |
|
Mute turns off in this scenario
in 7936 version 3-3-7-0 |
|
Second Call on shared line
cannot be resumed or muted |
|
7935 & 7936 Polycom phones lockup
on failover, loss of call preservation |
|
Display issue when Meet-Me
number is 10 digit |
|
Phone does not accept to change
the passcode with valid characters |
|
incorrect display on one of the
phone in sharedline |
|
Incorrect LED status on a phone
in sharedline with call waiting enabled |
|
7936 won't fallback to a TFTP
server once registered to an SRST router |
|
7936 Phone use odd RTP port
numbers |
|
7936 phone with phone load
3-3-8-0 does not work for FAC |
|
7936 Outside dial tone sounds
the same as inside dial tone |
|
Call gets disconnected if we
press hold & resume multiple times |
|
7936 does not play tone 50 (Zip)
when someone joins a conference |
|
Phone display is incorrect when
a bogus phone load is entered. |
|
Phone doesn't ring when **8 is
executed |
|
Phone hangs during failback and
failover with meetme |
|
Phone displays Registering
after CCM failover in a active call |
|
Dial tone stops when phone
receives a missed call |
7941/7961-7970/7971
no value for some items on
Device INformation page |
|
Phone should display ... for
very long Text or Number |
|
SSO Standby RP T/B
atm_ha_decode_vc_update+0x23c for ATM PVC bundle |
|
Phone registered to a CM 3.3
shows only one line while call on hold |
|
Received and missed calls show
wrong calling party number |
|
Time stamps on console messages
and phone display is not the same |
|
Deselected call in sorted call
list appears with other selected calls |
|
Turbo Gabage at the end of
Network Statistic screen |
|
Cancel softkey has delayed response
when looking up a bogus DNS addr |
|
Phone resets wmore volume of
call are placed on sidecar lines |
|
wbm failed to extract signature
when display filter was used |
|
Turbo Can not remove Doamin
Name on phone |
|
Phone does not remove the
default router config |
|
Increase max CPU usage timeout
for JVM process |
|
SIP TNP 1.1 image stress run
freezes phone UI |
|
Phones unable to Rx or Tx
Multicast Services when Publisher fails. |
|
Phone w/200 calls active single
line reset w/calling phone reset |
|
dhcp.conf could have invalid my
name entry |
|
Add consolle trace to indicatie
the call is an encripted call |
|
Phone doesn't register when it
is unable to resolve the CCM name |
|
paging group display delayed on
7911 with CME |
|
get SW port returned -1 error
after downgrade to 6.0(2)SR1 |
|
Phone stops playing multicast
after an unanswered call |
|
local Ip/port value is cleared
but others are kept for an ended cal |
|
LED does not blinking red while
the DCP is busy |
|
7970/7971 Touch Screen issue IP
Phone URL shows Delay |
|
ogins with sys group
permissions on release signed phones |
|
timeZone tag errors |
|
Background Image thumbnails not
displayed in correct order |
|
7961 Row of Pixels missing on
Line View graphic |
|
phone locks up when SEP
dateTimeSetting is empty |
|
phone locks up when SEP
dateTemplate is MM/DD/YY |
|
Phone display goes blank for
consult transfer to busy monitor line |
|
when PickUp softkey is pressed
on onhook phone displays ??? |
|
Service URI cause phone to
unexpectedly shutdown |
|
need to press mute twice for an
incoming intercom call |
|
Assign a same IP port to RX and
TX socket - casues 1 way audio |
|
Phone doesn't play Zip/ZipZip
Tones toward network |
|
Phone Rcvr Lost Pkt reports as
a negative no under impairement |
|
SIP TNP DSP debug seen when
pressing Settings, Directories, or Services |
|
Reference getPegs() via IMedia
interface instead of directly |
|
Turbo Phone receives mcast pkts
when port open forMcast transmit |
|
Turbo Error Verifying Config
Info after LSC install on secure phone |
|
README-SGM-pdsources on DVD has
SGM references |
|
Phone Should handle
gethostbyname failure and print appropriate Err Msgs |
|
Phone not displaying all Placed
call list when pressing up/down button |
|
Corporate directory search
fails if username contains special characters |
|
wirelss client to client can
not pass traffic |
|
Service URL feature assigned in
em profile does not work |
|
Phone sends Duplicate DHCP
Discover Message |
|
Phone freeze after reset stress |
|
Phone displays wrong msg when
registration rejected for security reason |
|
phone doesn't show up old admin
vlan id in Current Admin. VLAN Id |
|
Corporate Directory Search
Fails When using Russian Locale |
|
Add Title to Line View to identify
which line the calls belong to |
|
Having directory menu open
causes Callback to not working properly |
|
HTTP CGI ModeInfo query does
not return if Services URL doesn't resolve |
|
Ethernet Disconnected Mesasge
does not appear when Ethernet unplugged |
|
Turbo Missing status messages
on Load Server parameter |
|
No status message when TFTP
service is down on load server |
|
LineInfo web age query does n't
show up Messagewaiting Indication. |
|
Phone won't failback to a TFTP
server once registered to an SRST router |
|
HTTP req canclled msg when
hitting a softkey |
|
Japanese locale (td-sip.jar)
not loading on SIP phones. |
|
Removing JVM from 7.0 on 8.0
CPK files (to avoid out of space errors) |
|
Turbo status message No Default
Router after changing DHCP=no to yes |
|
Phone does not preserve the
state of mute/spkr button in handset mode |
|
Skittles phone does not complain
with junk value in displayOnDuration |
|
Making DSP standalone on
phones- dsp.cnu reads dspfw.bin |
|
select image
Userpreference->Background image display invalid png icon |
|
CDP unexpectedly shutdown from
broadcasted CDP pkt, results in restart of all apps |
|
Privacy lamp is not being
displayed correctly on 7941 SCCP phone |
|
Phone unable to come out of
Service Menu using CANCEL softkey |
|
Phone responds to CDP triggers
from upstream port |
|
phone does not play precedence
CW tone |
|
Calls drop during CME failback |
|
Phone is stuck if Encrypted
Config is on and supporting load is absent |
|
phone doesn't come up with DHCP
enable when Voice VLAN = Access VLAN |
|
Incorrect response for
unicast/invalid IP adress for RTPMTx i p URI |
|
CiscoIPPhoneExecute ExecuteItem
priority 1 is ignored in some cases. |
|
Invalid Ip Address to be
displayed while validating Null values. |
|
Turbo lost audio w/ 100%
broadcast traffic |
|
Status Msg timestamps changed
between 24hr/12hr formats on reset |
|
CP-7970 firmware version 7.0(1)
distorts background image color |
|
Softkey changes from Connected
Transfer state to On Hold state |
|
Phone is loosing the
querystring parameter on the refresh |
|
Phone Multicast services not
working |
|
LSC Installed Status Messages
is not displayed on phones |
|
cBarge Target phone changes
focus when other party cBarges |
|
Phone doesn't dial from placed
call listwhen editdial& dial is pressed . |
|
Phone Displays UI with no keys
for a shared line scenario. |
|
Phone CGI URLs never complete
HTTP transaction |
|
Services page text does not
display properly |
|
Idle phones never send SCCP
TimeDateReq to sync clock |
|
Pressing the '.' soft key in
the edit menu doesn't force Kate String T/O |
|
Clicking noise is heard in
encripted call when duplicating packets |
|
Phone plays garbled audio for
PA prompts |
|
phone displays ??? as Codec in
Call Statistics window |
|
Call Stats window displays
wrong info for Rcvr Lost Pkts/Discarded |
|
IP Phones use random UDP source
port for RTP media |
|
Phones stop sending KA when
backup TCP link down |
|
call bubble does not disappear
when there is no active call |
|
High End Phones connect to CCM
sub that is not present in the CTL file |
|
Turbo fine-tune displaying
errors of dspSendFrame _framePutEgressFrame |
|
Turbo InsideDialTone could not
be stopped after removing CFwdAll |
|
UDI Support |
|
Turbo Codenomicon HTTP test
39730 causes sunvm CPUTime Limit Exceeded |
|
Add core file decoded core file
to the serviceability webpage |
|
SIP phone loads and CCM are out
of sync for PC Voice VLAN Access |
|
GARP enable/disable reversed |
|
Property Errors - Settings Can
Be Lost |
|
phonerebooting when secondary
CME inaccessible and keepalive is 10 |
|
Enhance the flush operation in
the RecordStore |
|
HTTP Client locks up upon
consecutive posts to CGI Execute |
|
No prompt/status in Detail call
history record |
|
Dial Softkey Enabled when no
Active Audio Path or no CCM |
|
Erase from Top-Level Settings
Menu does delete sidecar contrast |
|
SIP Phone does not do a TLS session
reuse after network failure |
|
RMS Store must be deleted in
order for phone to boot correclty. |
|
Phone stuck after erase under
Settings menu |
|
JPhone Overview displays
incorrect topcall if some RIUs made private |
|
GARP enabled native code
returning incorrect value |
|
Phone could not recover after
DNS entry be corrected |
|
Phone sends Invalid Message for
SCCP v3 and v4 |
|
Phone Answer softkey not
displayed for new icoming call |
|
Remote In Use Icon/LED not
shown when shared line is private |
|
HTTP Authentication Does not
Show Response |
|
Able to Change Ring Volume Even
when Setting Access set to Disable |
|
TimeDateReq to sync clock
causes KeepAlive to miss one interval. |
|
7970/7971 InCorrect Date Format
Shown Under Missed Calls |
|
2 meg file limit cause double
boot when upgrading to 8.0 load |
|
JAVA/TNP Log/trace related
changes |
|
CNU syslog changes for 7.0.2.x
branch |
|
getportcfg check for errors on
msgsnd() |
|
Display distorts, when held
calls goes from three to two |
ATA18X
ATA SCCP Incorrect Call Waiting
behavior |
|
Conference to ATA-Phone thru
H323 & ATA-phone on same CME doesnt work |
|
ATA flooding callmanager with SoftkeyeventNew
call skinny messages |
|
Problem transfering calls using
ATA and CME |
|
Update signaling ToS to be
consistent with current design guides |
|
ATA186 configuration web page
should state clicking rather than click |
|
ATA SCCP sent AVT message when
sent DTMF to SCCP endpoint |
|
No Secondary dialtone played by
ATA SCCP |
|
ATA186 excessive TCP ACK delay
after receiving SKINNY message |
|
ATA SCCP sends excessive
StationSendTimeDateReq |
4.1(3)es40 (Base for 4.1(3)sr3c, sr3b, & sr3a)
Max CDR Records exceeded if SQL
Agent service is not ready during init |
|
MGCP-Need configurable timer
waiting for FXS onhook when call ends |
|
CTI manager running high CPU
with CTIERR_SHUTTING_DOWN errors |
|
CiiscoatUserProfile and ciscoatUserProfileString
not updated |
|
Missing disconnect for conf
parent in alerting/drop scenario |
|
Firewall support for attendant
console in skate |
|
Remove Redundant FORWARD Trace
Events in CCM SDI Trace |
|
Unanswered call to Huntlist is
cleared with incorrect cause code |
|
Race Condition Occurs in CCM that
Causes Call to Get Dropped |
|
Support of DDI trailing |
|
CM need support for new phones in
devicelistx.asp file |
|
Tunneled protocol not available
for H225 gatekeeper controlled trunk |
|
CTL client returns 'No valid
server certificate found' inserting etoken |
|
ES/SR Installation needs
corresponding code for CSCsb44801 resolution |
|
stopservices needs error
handling update |
|
Enlarge
splashscreen in ES/SR installaton |
|
Need new sections for file copy
ops |
|
Update SQL script handling |
|
Enhance error handling
reporting and dialogs |
|
End of installation Dialog
Changes needed for Device Package |
|
Sub installation failed because
no user tables for CCM database on Sub |
|
CCM 4.1.3 sr1 sending
Mal-formed DNS request |
|
PRI Sends Cause Code 0 On Drop
Party From Conference |
|
H.323 Sends Cause Code 0 On
Drop Party From Conference |
|
E164 Mask change notification
issue for DNs with wild characters |
|
CCM does not update analog port
status for analog GW (need rej msg) |
|
CAR report CDR Search by
Gateway displays incorrect records |
|
Implement group listening. |
|
Changes in clearcase not
properly built into ES |
|
Stopservices to display
services being stopped. |
|
CVTA Failed call to MGCP BRI
gateway - bearer cap 0x8080A5 |
|
CCM MGCPbrid device didn't handle
CcSelectFacilityReq message properly |
|
CCM Initialization Digit
Analysis State Takes 4+ Minutes To Complete |
|
CCM doesn't sent stop alerting
tone |
|
CallBack does not work after
modifying the CallManager Group |
|
Race Condition Occurs in CCM
that Causes Call to Get Dropped |
|
CTIManager unexpectedly
shutdown with Access Voilation |
|
raven Voice Quality Problems
using SIP based VoIP |
|
AXL response containing junk
characters. |
|
Cisco TFTP perfmon counters can
not be viewed through perfmon |
|
Slavonic Languages Delta on the
localized dictionaries |
|
JTAPI Client causes issues with ICM
Jtapi Gateway |
|
PlatformException sent to Apps erroneously
when call is xfer'ed/dropped |
|
JTAPI is not sending
CiscoAddressCreatedEv |
|
WebDialer takes line with
lowest DN on user device porfile |
|
PCM change breaks 4.2 and lower
builds. |
|
Need tag for 6608-MTP/CFB in
ccm xml |
|
Callback seizes to function
after a while |
|
log service stopped event in
SDL traces |
|
Call Manager restart setting up
media for MGCP call |
|
Locations Bandwidth Leak |
|
CCM Can not form the TO packet
that is required by LCS |
|
ES34 causes global directory
pages to break |
|
AdminUtility does not write out
a log file |
|
AdminUtility should control
password changes for the IWAM_Guest account |
|
AdminUtility is not stopping
services |
|
enhance adminutil to validate
usernames |
|
enhance adminutil to be
compatible across Cisco CallManager versions |
|
enhance adminutil to perform
additional operating system checks |
|
enhance adminutil to reset dcom
permissions |
|
Translated Rerouting Text not
shown on phone |
|
Sending Complete Setup Msg to
overlap Route Pattern fails |
|
MTP Orphaned Stream w/H.323
Call On Hold - Incorrect CI |
|
Call fails to connect after
dialing FAC code in a scenario |
|
There is no StartMedia
Transmission to the IP phone when it re-opens |
|
Bandwidth leakage allocation in
CCM |
|
Hunt group was not utilizing
the T1 CAS circuits on a Gway until reset. |
|
ccm.exe terminates unexpectedly
after trunk reset w/ DNS server offline |
|
Softkeys greyed out for a
barged call that is barged again |
|
Need Inbound Redirecting Number
IE over QSIG PRI for interoperability |
|
T38H323-H323 fax arcoss CCM
nodes not supported |
|
Preserve active H323 GW call
during quiet clear |
|
CTI Route Point is using the
configured DNas Redirect |
|
Voice Mail Port Wizard fails
with DBL Exception |
|
updatePhone - invalid Max Call and
Busy Trigger causes line disassoc |
|
log service stopped event in
SDL traces |
|
Disable Nonregistered SCCP
Keepalives default value should be False |
|
DialingForestDumpEnabled
service param should warn of CCM terminations |
|
BAT Phone validation fails with
comma in Display or Alerting Name |
|
Deleting Unassigned DN with BAT
causes deletion of configured devices |
|
CCMAdmin Password Validation
should be proper once enabling MLA !! |
|
Region name fields should allow
30 character in regionconfig.asp |
|
Changing partition name not
implemented until CSS is changed |
|
Route Filters can not be
selected when Max List Box Items is exceeded |
|
CCM Inter-Cluster Trunk Wait
for Far End H.245 Terminal option |
|
Inbound Redirecting Number IE Delivery
should be selectable for QSig |
|
No validation done if beginning
DN is empty in VM Port wizard |
|
TAPS should be made compatible
with CRS 4.0 |
|
VG224 configured for shared
line on Callmanager fails |
|
devices attempting to register
prior to CCM being up |
|
Unable to complete the
conference |
|
CTIManager out of service
making PhoneLine to go into incorrect state |
|
Cisco IP Voice Media Streaming
App using SW CFBs stops unexpectedly. |
|
updateGatewayEndpoint fails
after insert 24 ports |
|
Error comes on clicking Update
on Autogenerated Device Profile |
|
Remote scripting error on web
page if updated after long idle time. |
|
Blank popup message after
session timeout popup |
|
7.0(2)SR1 image for the
7941/7961 checkin to 3.3, 4.0 and 4.1CCM release |
|
7970/71 7.0(2)SR1 image check
in |
|
Add online doc. name to 7911
SCCP loads |
|
Stndrd Feature 7960 sftky
profile fail on 7940 CallBack equipped phone |
|
Update/Make 7911 ready for FCS
and prepare Skate SR build |
|
AgenaInterface leak when
remotely join party |
|
Last party in the meet-me conf
closes if other parties has Tx failure |
|
ccm.exe unexpectedly shutdown
when printing Media_PayloadList[capsInB[5].payloadCapabil |
|
CCM Initialization-Forward
Phase In SsInit Takes 34 Minutes To Complete |
|
race condition in CTI
failover/failback |
|
CallManager forwards
conferenced call to default VM Profile |
|
CCM Init/RuntimeDETAILED DBL
Trace For FORWARD Phase Is Too Verbose |
|
CCMAdmin Read Only User Can
Escalate Privileges |
|
Unauthorized Alteration of
CCMAdmin Administrator Privileges |
|
CCMAdmin Read Only User Can
Escalate Privileges |
|
CCMAdmin Read Only User Can
Escalate Privileges |
|
MeetMe needs to have additional
tracing to track leaks in conf use |
|
CTIMnager unexpectedly shutdown
access violation |
|
Dialed Number Analyzer fails
after NZT Daylights Savings Time Start |
|
invalid GSM EFR audioUnitSize
should not cause CCM not to send TCS |
|
H.323 Faststart call fails
after getting 2 ORCAck from IOS gateway MTP |
|
CM sends ARQ with nonzero bw
for callback via GK controlled ICT |
|
CFwdALL may fail to clear for
Shared DN |
|
ASTISAPI.DLL Memory Leak Upon
CMLAUserPermission--setUserID() Failure |
|
Call Pickup fails on Hunt List |
|
Application menu items should
not be in all CAPS |
|
CAR version 4.1(0.34) cannot
retrieve data passed certain dates |
|
Moving clOck forward cause
JTAPI Exception and Provider going OOS |
|
App Event log Warning not
always generated when CM service stopped |
|
CCM sends sendTCS to device
registered in h323 gw mode |
|
Call forward on QSIG reroute
fails |
|
Aupair Sustained CPU Spike -
ghSendQueueSem Deleted On CCM Change |
|
remove loggingDisplay option
for 7941...7961G-GE phones from CCM/Windows |
|
RUS-JTAPI files shows garbage
in the preference window |
|
JTAPI deadlocks when trying to deliver
event at same time agent logs out |
|
Invalid DisconnectedEvent in
conference release |
|
Cisco JTAPI does not work with
IBM JVM 1.4.2 |
|
Address on CTIPort is out of
service if registered after adding observer |
|
InvalidStateExceptionImpl when
jgw attempt to send call to CTI manager |
|
Support new phone cert in CAPF |
|
ToneOnHold played when user
drops from external call |
|
CallManager unexpectedly
shutdown (access Voilation) in Cdcc |
|
CCM 4.1(3)sr1 - SIP trunk
Diversion info lost |
|
QSIG Loops on CallForwardAll to
OffNet DN |
|
Callmanager propogates
disconnect cause 0x9F |
|
Logging Display and Load Server
features do not appear for the 7970/7971 |
|
Adding DN get stuck in
Verifying state |
|
Attendant Console fails to redirect
Queued calls to Huntgroup |
|
Attendant Console gets an error
message Failed to make new call |
|
AC outbound call does not use
primary line |
|
OrininalPartyName and LRPName
coming blank in inter-cluster unpark |
|
LineTransferEndedEvent Missing
because of CallProcessing Issues |
|
DSP Keepalive Timeout for MOH
Multicast |
|
Memory leak in AgenaInterface |
|
ccm.exe unexpectedly shutdown
(access voilation) with CcSetupCompReq |
|
add service parameter for
progress->disconnect translation |
|
CTI does not query database as
part of ProviderOpen |
|
VPT receives corrupted HTTP
header in AXL response |
|
SIP Default Telephony Event
Payload Type Range ends at 120 not 127 |
|
Call Manager 4.0(2a) SR2b
unexpectedly shutdown when masking called pattern |
|
Q931 field does not contain
release cause for Annex M1 calls |
|
CMI service does not restart
when it loses DB connection |
|
Stuck call |
|
BAT insert fails if phone
description contains comma |
|
Unable to update MLA's User
Group Base. |
|
Route Group page takes too long
to display available devices |
|
Diverting to specified
directory number isn't working |
|
Stored procedure was not
replaced correctly on Sr1 Installation |
7911
Checkin 7911 f/w loads to create
Device Packs for FCS |
7902/7905/7912
7912 fails due to malicious
VLAN tagging |
|
7912 does not play UK dial tone |
|
7905/12 phones lose Service
button after EM update |
|
phone - 7912 phone reboots
after receiving 3 IMs quickly |
|
Only a 7912 shared number phone
work when configured max-dn dual-line |
|
No dial tone after the 7905 and
7912 SCCP failover to SRST |
|
7912G-A phones cause PC's
behind them not to retain an IP Address |
|
Long delay for PC to obtain
network connectivity when used with 7912G-A |
|
7912/05 should always Reset
unless an rtp stream is active |
|
CCCM 5.0 & 7905/12 does not
show external number on top line of display |
|
7912 SCCP sends excessive
StationSendTimeDateReq in idle mode |
|
7912/05 excessive TCP ACK delay
after receiving SKINNY message |
|
7912/05 RTPMTx sets TTL of sent
multicast packets to 1 |
|
Timedate req. msg. storm from
at midnight |
7920
Extension Mobility does not
work with Services URL Button on 7920 |
|
7920 Doesn't Support Vibrate
URI |
|
Need a menu to display
configured regulatory domain |
|
Need a menu to display current
transmit power |
|
7920 Does Not Support CCA
Versions of QBSS |
|
7920 can spontaneously
re-register to CM in idle with INF-MIB error |
|
7920 Can Associate to a Lower
Priority Profile When Set to Auto Profile |
|
Upgrade to 2.0 will cause phone
lock password corruption |
|
CCM 5.0 Centralized TFTP
compatibility enhancement |
|
Port 17185/udp is open on 7920
phone |
|
7920 RTPMTx sets TTL of sent
multicast packets to 1 |
|
7920 call-forward noan on
second active call results in phone hanging |
|
7920 can corrupt the CCKM
Timestamp |
|
Invalid XML object sizes can
cause the 7920 to reboot |
|
Idle URL can cause the 7920 to
lock up |
|
7920 will roam off a strong
signal AP to a weaker one |
|
7920 should continue streaming
RTP packets when on Mute |
|
7920 can fail to ACK G711
packets during a call |
|
7920 Can Roam More Frequently
With 12.3(7)JA AP Image |
|
7920 Can Stop Scanning Although
Still Associated |
|
7920 send 802.11 Auth suddenly
and it causes choppy audio |
|
Channels in Active List are not
flushed after 3 missed CM Keepalives |
|
Emergin's alert tone volume
needs to be limited when on-call |
|
CP-7920 is not responding to AP
packets |
|
MWI tone can be very loud to
user if CP-7290 re registers |
|
Need to roam when QBSS max
threshold is met |
|
7920 MR2.0.1 firmware upgrade |
7936
7936 Transmit Jitter Extremely
Sporadic - 2 Second Cycle |
7935
CP-7935 generates choppy audio
when in a conference call |
7941/61
The Exit softkey is not working
on the Callback screen. |
|
Privacy lamp is not being
displayed correctly on the phone. |
|
Add fault-tolerance to file
system. |
|
checkin 7.0(2) firmware for
7941/7961 phones into CCM/Windows |
7970/71
7.0(2) firmware for 7970/71 |
6608
CallManager may incorrectly put
a 6608 CAS port OOS |
|
6608-Glare conditions on T1 CAS
is not cleared appropriately |
6608 E1/T1
Calls through 6608 T1 CAS
trunks are not preserved |
|
T1-CAS E&M ports on a 6608
card unregistering during stress test |
|
Periodic T1-CAS E&M channel
out-of-service during 6608 stress test |
6624
change configuration link is
not opening for 6608 & 6624 GWs. |
4.1(3)es25 (Base for
4.1(3)sr2)
High cpu with ccm, cti and
gatekeeper configured |
|
CCM faulters on backhaul
messages to 6608 for T1 CAS hookflash transfer |
|
Put PerfmonQueryAllCounter ASTIsapi
Url back to 4.1.3.sr.1 |
|
Enable Database Related SYMBOL
and MAP Files During ES/SR Build |
|
Delay on DN lookup in CCMAdmin
with large number of CallPickup Groups |
|
Route Group Configuration
screen does not show Available Devices |
|
CM SDLListeningPort service parameter
should not allow a value of 0 |
|
CCM CCMG for inter Cluster
Trunks does not limit GK registrations |
|
Established Flood causes high
CPU usage or unexpectedly shutdown ccm process |
|
Can't save IPMA mananger's
config if divert target contains number zero |
|
CallManager-improve handling of
idle TCP connections |
|
TCP connections not managed
aggressively |
|
TCP connections not managed
aggressively |
|
CAR 4.1(X) CDR search getting
Database access denied |
|
MGCP calls fail after failover |
|
AVVID ICT media exchange
timeout on CTI redirected call |
|
LDAP Access Error while
searching for users in CAR (clone of CSCsa60661) |
|
Wave driver thread leak |
|
One-way audio with CiscoTSP |
|
Callback doesn't work after CTI
Manager failover |
|
PC logging option is not
available for makaha |
|
CCM AXL API support for voice
mail pilot and profile |
|
Invalid PSS1 info may cause ccm
hang |
|
Incorrect DNIS using speeddial
and Route Pattern configured for overlap |
|
CNFA on hunt group pilot point
doesn't work for transfered calls. |
|
CM doesn't wait for more digits
if partial digits are rcvd for RP/XP |
|
CCM rejects incoming T1 CAS calls
intermittently due to race condition |
|
1 way speech path call from CME
FWD to operator transfer to ip phone |
|
Add 7985 QED support CCM
versions 4.X and 5.X |
|
7911 QED changes to support alt
scripts and load server |
|
Endcall Received After Second
Transfer Causes Disconnect |
|
New Call Failed To Be Pickup
Using Handset |
|
Auto pickup call does not show
forward info after connect |
|
RQNT before CAS DT/oc
interruptted DT/sup |
|
IpVmsApp on Subscriber pegs to
100% CPU |
|
Checkin ip7961.pdf ver3
into3.3.5.eng.spec, 4.0.2.eng.spec, 4.1.2.eng... |
|
CallManager terminates
unexpectedly, RaiseException |
|
TFTP Does Not Build All
Configuration Files |
|
Subscription Pull Takes Almost
6 Hours To Complete |
|
Wrong call details on shared
line console |
|
Unwanted error pop up on
console with shared lines.. |
|
The line state is broken when
using dialrules.XML |
|
Enable visibility of Makaha
types in dev packs 3.3.5.eng.spec, 4.0.2. .. |
|
Inband info not heard by IP
phone when ISDN DISC+PI received after SETUP |
|
Inband announcment not heard
when calling busy or unallocated numbers |
|
Secondary line set to flash
only will only blink the icon and not lamp |
|
Need to bump the SDL version
number due to changes in CSCef64304 |
|
7961/7941 font should be more
readable - suggest making tallerCSCef28642 |
|
Device Association Page
distorted & JScript Err after a bad search |
|
MLPP config not available for
3845 MGCP gateway |
|
On 7970 Display-on-Time shows
default value after setting it to blank |
|
Station stay at CONNECTED state
after call release |
|
Media Component Race Condition
Leads To MRM And Process Leaks |
|
Primary CMI does not send
KeepAlives to Voicemail |
|
Change Notify stops working due
to bug in TcpLib |
|
Second TCS from H.323 Tandberg
is not handled properly by CCM |
|
dtmf not sent on t1 cas If call
is not in connect state |
|
Ericsson MD110 PBX CCBS/NR
CallBack Interoperability issue |
|
Standard Phone FG does not
Allow Changes to EM Select User Profile |
|
MLA generates error when
configuring partition for DN |
|
Install Migration for AIM-VOICE-30(332)
to AIM-VOICE-30-SLOT-0 (412)fail |
|
InsertCDR.exe taking 1.5 GB of
Memory |
|
CCM Srvce Unexpectedly Restrts
during a fax operation usin H.323 gateway |
|
CCM SIP call failed when the
INVITE message has a phone-context tag |
|
Pilot point busy if member sets
CFDWall back to Pilot Point |
|
Agent stuck in talking after
Outbound Option call |
|
4.0(2) wrong line status
returned by jtapi |
|
selectRouteThread and
EventThread are blocked for 15sec. |
|
Cisco Jtapi stops sending
events after address is manupulated byCCMAdmin |
|
CATUrgent need to get JTAPI
build to Catalan theater with revisions |
|
TurboError Extracting File
using latest tc-sccp.jar file |
|
AC client showing wrong line
status |
|
Device Pool not getting updated
for 7912 and 7905 phone. |
|
CallManager terminates
unexpectedly, RaiseException |
|
InsertCDR service stops
populating CDR database from flat files |
|
Implement JAVA side and QED CM
interface |
|
Catalan fail to launch due to
wrong language code in localelistings.prop |
|
Idivert Key upon being pressed
get temp fail |
|
LowAvailableVirtualMemory alert
triggers when 70% or more memory free |
|
Unable to manage Personal
Address book via CCMUSER page |
|
DevPack does not install the
locale files |
|
No alarm when maximum devices
per provider is exceeded |
|
No alarm when maximum devices
per node is exceeded |
|
Deleting a transcoder disables
transcoding for the whole cluster |
|
CCM doesn't clear the h225 call
properly when PSTN hangs up |
|
CDR value is not correct when
using Auto Call Pickup |
|
Comment Column In
CallDetailRecord Table Does Not Support 2048 Chars |
|
Enable fclosethread or start
CCM w/ thread corrupts SDI index to -1/0 |
|
Wave driver incrementing RTP
sequence #s during silence |
|
Additional languages for
CM4.1(3) |
|
Marker Bit not set in the first
RTP packet after silence. |
|
Change notification stopped
working after route filter change |
|
CFA stops working after CCM has
been running under load |
|
IP phone re-registers after set
or unset of call forwarding |
|
Add QED support for 7911 |
|
AC displays err message during
preemption on an attendant phone |
|
Pop message when pressed save
on the Attendant console GUI |
|
Attendant Console shows Unknown
Error at Basic Settings |
|
Polycom ViewStation Call
disconnects |
|
CC returns unmodifiedCGPN same
as CGPN. Issues with states of agents |
|
High number of voice
packets/frame in outbound fast start |
|
DMS-100 spec does not recognize
ISDN Q.931/Q.850 Disc Cause Code 53 |
|
Incorrect cause code is
returned when the line is not registered |
|
Always use prime line is not
working with 7.1.2 phone load |
|
Messages button works
intermitently |
|
AS-8 gateway stops supporting
SMDI after upgrading to CM 4.02a |
|
Call Pickup fails
intermittently |
|
CCM prepened the prefix to Cgpn
for CLIR calls via H.323 GW. |
|
CM Deducting twice the Audio BW
and returning only half when call comple |
|
CCM doesn't instruct 6624 to generate
outside dia ltone |
|
h323 faststart to MGCP calls
fail when h323 has active caps enabled |
|
unexpected shutdown in
MeetMeConference when accessing NULL pl/spl lists |
|
CTI Change needed to accomodate
CCM Change required for Prime Line |
|
RBT is not heard on the PSTN
side while call routing to an agent |
|
ForwardManager does not remove
map table (mPartyToActiveCallIndexMap) |
|
MWI requests fail when
originating device goes onhook quickly |
|
CTINewCallAcceptTimer expires
during lineRedirect causes timing issue |
|
TCD is requesting redirect to
an available hunt group member, calls fail |
|
CallManager terminates
unexpectedly during IP Phone registration |
|
RTMT installs
outdated/duplicate/unsupported JRE 1.4.1_01 |
|
TFTP not serving requests,
stuck with 200 requests in progress |
|
CNF stops sending CTFTP
changes. |
|
7961 device pack doesnt conatin
proper device name on device default |
|
Unable to access Database also
Publisher out of Disk Space |
|
AXL Allows Creation of Duplicate
Route Patterns |
|
ADCM Tools will not function
w/multiple clusters in same AD domain |
|
Directory throwing exception
when manager DN does not exist in iPlanetDirUser, UserManager |
|
Call Activity Report incorrect
reporting on PRI count in service |
|
java.exe consumes 100% CPU
leading to CallManager restart |
|
Validation not done for
Auto-registration Information |
|
Unannounced products show up in
various admin pages |
|
Garbage characters on JTAPI
Preferences launched on Japanese PC |
|
Misleading message in JTPrefs
console window. |
|
Need a reason/cause for the
CallCtlConnFailedEv to indicate MLPP |
|
Unexpected
CallCtlTermConnTalkingEv after disconnected |
|
Error on phone page in DNA |
|
Patch Install says file
replaced successfully whether done or not |
|
Msg if we wish not to view log
should be consistent for install/unin |
|
SR doesnt Init Database on
replication failure detected scenario |
|
Device Default is updated when
uninstalling ES/SR |
|
Wrong Upgrade Message when
upgrading to SR01-rc02 |
|
Unwanted msg leading to err
pops up while upgrading to 4.0(2a)SR01 |
|
Misleading CCm Ver Msg if Patch
installed on a Non-CCM Server |
|
SR Patch Ver check lists From
as old SR and not new MR and misleads |
|
Remove the extra are-you-sure
from the ES/SR installs |
|
Uninstall Confirmation dialog should
mention version reverting to |
|
Support needed for Ext Device
Package execution during ES/SR install |
|
Need to dump a list of running
processes during installation. |
|
CCM 4.0(2a) - DCD terminates
during quiesce operation for backup. |
|
AXL missing a few key handlers |
|
Attendant Console does not
retain window focus |
|
Need to add Service parameter
Always play outside dial tone |
|
Enhancement to Modify APDU ext
num for outgoing Qsig MWI on/off messages |
|
Call Forward to Multiple Busy
Users gets no busy tone |
|
Pressing the Transfer softkey
on a selected call deselects the call |
|
Annex M.1 trunks need to
optionally ignore tunelled content |
|
Call Join Request fails |
|
When Auto Call PickUp IP Phone
does not display For. |
|
First character of Caller ID is
stripped in Japanese environment |
|
CCM constant
registrationRequests to GK if no TTL in registrationConfirm |
|
No ringback tone when calling
from CME to Qsig PBX via CCM |
|
CTI Route Points remain
registered after CTI application shutdown |
|
CTI unexpectedly shutdown when
device is removed from control list |
|
Unnessecary changenotification
sent to DeviceLineMgr causes CPU load |
|
LDAP Access Error while
searching for users in CAR (cloned CSCsa64436) |
|
CM hangs on blank screen upon
reload with USB mcast MOH audio src |
|
Error -1 [Internal Error]
Unknown user on 7940 when adding Fast Dial |
|
1700 GWs FXO ports are allowed
to be configured for diff signaling. |
|
ONLINE HELP Ring tone help
screen needs to replace Alert with Ring |
|
ONLINE HELP Device Configuration
help need updated with new submenus |
|
ONLINE HELP Help info for
editing IP address needs addtional steps |
|
ONLINE HELP Erase softkey help
under Settings needs more information |
|
ONLINE HELP Help for Network
Settings DNS Server 1 returns error |
|
ONLINE HELP Default softkey under
some User Preferences returns no help |
|
No Help content for the softkey
OPickUp. |
|
Greyed ERASE softkey is
actually enabled |
|
Caller ID gone from shared line
after a barge |
|
> in 7940/60 i-button help
text |
|
sidecar lamp shows red for
barge/cbarged calls |
|
7960/40 Device Info page does
not follow Message Waiting Lamp Policy |
|
Display settings on Phone should
be changed for Restricted Display |
|
7960 can load a Ringlist.xml
with more than 50 entries |
|
Remove conditional code |
|
IPPS authentication
credentials, % sign not URL encoded |
|
PC can't ping 7960 phone with
dot1p configured |
|
fclose thread flag should be
set to true by default to avoid cpu spike |
|
CM disconnects call when phone
goes off hook |
|
CM Cas trunk in cm shows
registered without NMHDV in ios router |
|
illegal line errors in CCM log? |
|
CallManager terminates
unexpectedly,need to handle exception in dbprocs |
|
CCM sends 2 StartMediaTransmi
Msgs without a StopMediaTransmi between in |
|
7960-7914 does not ring on
incoming call if there is active call on 7914 |
|
Not receiving NOTIFY, Called
Party Number is not displayed properly. ICT |
|
CallControl Should look at all
the Fac IE's in the CfDataInd signal |
|
ReleaseComplete CRV High Order
Bit Not Flipped |
|
Admin page does not open after installation
of SR1 Rc02 |
|
Unable to have a NON-QSIG ICT
in a mixed routelist |
|
CCM unexpectedly shutdown
intermittently on changing the CCM server's timezone |
|
Can not add more than 39
Devices in Media Resource Group |
|
Unable to delete IPMA assistant
in Catalan locale |
|
Video capability for
Communicator has to be added |
|
support for EM2-HDA-4FXO in CCM |
|
CallManager ARQs for wrong
E.164 address when calling H.323 client |
|
AXL AddRegion does not support
Default Codec With Other Regions |
|
AXL return unknown error for
updatePhone after IP service got deleted |
|
StationUpdateCapability from
VTA doesn't list all codecs in CCM Trace |
|
Flow control is not symmetric
if one video location is unlimited |
4.1(3)es06 (Base for
4.1(3)sr1)
Maketypes needs run after Product CSV's added to branch |
|
Change default value for Disable Non-Registered SCCP
Keepalives to False |
|
TSP access violation with CCM 4.0 |
|
802.1x auth state remains after PC disconnect |
|
Incorrect status msg when no ctl on phone and modified ctl
dwnld |
|
7960/40 does not support QueryStringParam as documented in
SDK |
|
IPSvcssupported xml fields size are 1 less than max |
|
IPsvcNew http headers support as per SDK 4.0(1) |
|
Lock icon overlaps to page title text |
|
Mid-call video starts when active call is in mute state |
|
Phone shows encrypted call with CM 3.3 |
|
Security Configuration menu name should be separate from
title |
|
Clear softkey doesnt clear interface stats on HTTP page |
|
Autodial fails on choosing hold option for the current
call |
|
Not able to scroll down to see help pages displayed by i
button |
|
7940/60 phone should use HTTP 1.1 for URL with IP address |
|
Auto line select enabled prevent use of softkeys on 1st
line |
|
7960 stuck in booting process when press service before
phone alive |
|
7960/7940Voice Quality Degradation With Echo Back To
Remote Party |
|
Shared line call doesnt display toggling between lines
correctly |
|
Support calloc caller PC broke LA built. |
|
Phone connects to secure SRST if bad config |
|
Clouseau debug infrastructure
implementation in 7960 sccp phones. |
|
Retain old BA while LA upgrade |
|
Disable the display debug tracing by default on 7960
phones |
|
Update copyright year on mid-range IP Phone boot display |
|
After a preserved calls is terminated, the phone is stuck |
|
Key rollover with Hold and EndCall Softkeys causes wrong
action |
|
7940/60 stuck in Configuring CM List state |
7940/60
Video stream not terminated
when CM is down Bsphere 2628 |
|
NetworkConfigurationX tag names
do not match Network Config UI |
|
Help for side car buttons throw
an error |
|
IPSvcssupported xml fields size
are 1 less than max |
|
Lock icon overlaps to page
title text |
|
Idle URLRefresh page does not
recover after a packet loss |
|
Phone accepts
invalid/Reserved/Multicast IP address |
|
invalid display by ip phone on
key pad uris push |
|
phone not updating volume
changes during call preservation state |
|
Handle current call not
displayed on dialing from directories |
|
pressing first line speed dial
causes second line to go offhook. |
|
No PORT_UP event on 7940 if
PCport on Phone changed frm 10Mbps-100Mb |
|
phone sends tftp request to ip
address 0.0.0.0 |
|
Phone does not retains Volume
Settings changes |
|
7960/40 phone will not fail
back to primary |
|
Change in behavior of resuming
the call that is onhold on IP Phone,7.1.2 |
|
speaker button won't work with
sidecar |
|
7940/7960 display HTTP
error[11] when pressing Services/Directory button |
|
Key rollover with Hold and
EndCall Softkeys causes wrong action |
7970/7971
Some items of Streaming
Statistics from 7970 inconsistant w/ 7960s |
|
Headset status indicator
incorrect after 7970 reboot |
|
7970 incorrect LineType for
some line buttons |
|
7970 not auto answer with
headset after restart w/ headset light on |
|
7970 not put active call in
focus after incoming call disconnected |
|
Phone restart with lower line rate
of multicast/broadcast traffic |
|
7970 fails to reregister after
temporary WAN failure |
|
Ringer volume and other
parameters are not configured aftr DSP reset |
|
Sidetone on handset after reset |
|
7970 ICMP hard errors behavior
changes |
|
7970 does not pick up the line
when configured share line |
|
Extra ring heard when answering
call after adjusting volume |
|
7970 RTPRx/RTPMRx URI syntax
error allowed |
|
Possible deadlock situation in
msg queue software |
|
Phone stuck at Configuring IP
after prolonged CCM disconnect/recon |
|
7970 drops host in DNS queries
with subdomains |
|
Skate Security config menu opt
5 and 6 display wrong softkeys |
|
7970 RTPRx/RTPMRx URI opens
invalid port by default |
|
Phone lockupCSCeg04380 |
|
7970 gethostbyname() does not
return multiple IP addresses |
|
Mute signal heard on network |
|
When resetting the phone
(**#**) PC loses network connectivity |
|
phone freezes during reboot
with mqThread problem |
|
7970 phone failover to SRST
takes more than 6 minutes |
|
Last digit not displayed when
dialing from keypad |
|
JavaException using Navigate
Keypad when call on hold |
|
Phone continue to stay with
Requesting msg, cancel key has no effect |
|
Java exception when 7970
configed with sidecar but none attached |
|
7970 Phone hangs on changing
existing speed dial from phone (CME) |
|
7970 unexpectedly shutdown when
access protected URL 2nd time |
|
Onhook Dialing will not accept
* or # as first digit |
|
Core dump of Sunvm.cnu when
web-access is disabled & then enabled |
|
Attempt to load diagnostic image
file causes CNU reset |
|
Onhook Dialing is available
when the phone is not registered |
|
7971 Multicast traffic dest to
PC dropped by switch in phone. |
|
RTPTx Stop not being executed |
|
7971 Unplugging and plug the
ethernet cable, looses VLAN id |
|
Incorrect time for New Zealand
time zone (GMT+12) |
|
7970 drops keys if pressed too
fast |
|
EM logged off profile keeps CFA
icon |
|
Update handling of init.conf
authentication settings |
|
SA Dereferencing pointer to
freed memory in Core/CNU/NetSys/udp.c |
|
SA expression must be a
modifiable lvalue in Core/Apps/cmds/ttrace/ |
|
SA Freeing pointer to already
freed memory in Core/Apps/daemons/DHC |
|
Broken autosensing on type-2 cabling
(BU-3494) |
|
Makaha power request numbers
are wrong |
|
ListenerManager allows for
multiple listener |
|
Memory leak when press keys in
predial |
|
Memory leak on startup in Call
History property |
|
7971 phone not upgrading load,
using device defaults. |
|
Phone reloads from nmap connect
scan |
|
Stream.c flood reloads phone |
|
Failover fail on 7971 phone
with CM 3.3.4(SR2) |
|
CVTA with 7970 messes up audio
caps |
|
Phone stuck at Updating
Software |
|
7970 - does not report Dest
Unreach on sendto() |
|
Ethernet Disconnected message interferes
with display (BU-3572) |
|
EndCall softkey doesnt work
when CM down and other end had hit Hold |
|
7971 Low power backlight needs
to be 14 |
|
7970 - only retries 4 times
after leaseT1 expires |
|
7970 hangs at config IP after
reset |
|
Unexpected DHCP Renew after
Release operation |
|
Shared System Threads create
debugging problems |
|
Cut through on speaker phone
take approx one sec |
|
Line button becomes useless
after try dialing from call history |
|
Timer object should allow
ITimerListeners to disable timerCancelled |
|
7970 phone does not close the
sockets automatically |
|
Mid-call video starts when
active call is on mute |
|
7970 registering with CM when a
active call is in place |
|
7971 phone reset after
hold/resume duration |
|
Phone freeze after the
extension mobility duration test was run |
|
7970 hangs intermittently while
attempting EM login/logout |
|
XML parse error when text
object with 4000 chars of text is sent |
|
Multiple restart from CM causes
phone to freeze up |
|
http push may stop working |
|
Console shows CONSOLE TOO SLOW!
Skipping 0 log files! |
|
Trace does not include key
press information |
|
7971 Phone ignore vvlan
information from switch port |
|
CVTA does not receive
information on calls active when PC plugged in |
|
Phone stuck after erase
operation |
|
7971 does not comply with
802.3af power specification |
|
Phone can lose VLAN id with
broadcast storms in the network |
|
PC attached to Phone loses
network after multiple phone reload |
|
7971 phone re-boots when
SYNC_RCVD state sttack was run |
|
Enable 802.3x flow control |
|
7970 plays loud comfortable
noise when using G.729 codec |
|
Can not accept calls when call
history is empty and in focus |
|
7970 change between daylight and
standard time 1 hour too early |
|
Ringer stops working if press
speaker right after adjust ring volume |
|
Phone restarts exposes memory
leak in the CallAgent module |
|
Call Info gone but voice path
remains after brief Ethernet disconnec |
|
Phone does not take Service URL
w/ no label |
|
7971 w/ PC connected not
operate in low power mode using ieee inline |
|
7970 does not display missed
call info after waking the display |
|
Phone stuck under simClient
duration test |
|
7970 not alllow user to set IP
Address Release as No |
|
7970 should display IP address
released |
|
7970 missing date on console
logs, status messages & debug display |
|
7970 Autodial postpends to
dialed # if display name contaions #s |
|
UI issue services tab not
coming to foreground in push scenario |
|
7971 continuously resets if
dot1x configured on switch interface |
|
Services Changing volume while
RTPRx - softkey gets stuck at Save |
|
shownet command in cnush gives
wrong output |
|
7971 accepts untagged packets
while on a voice VLAN |
|
AbbrDial softkey appears on
7970 phone in CM3.x |
|
HTTP Push requests has
successful response, but UI does not display XML |
|
7970 does not properly reset causing
sessions hung in LAST_ACK on CCM |
|
7971 PC port does not show what
is configured |
|
CP-7970 Fails to Boot up if
'switchport voice vlan dot1p' is configured |
|
Bad voice on 7971 phone with
10% broadcast traffic |
|
Broadcast traffic throttling
rate very low w/ load 69 on 7971 phone |
|
7971 phone only allows 10M (1%)
broadcast traffic send to PC |
|
Phone does not pass thru all
multicast traffic to PC |
|
7971 switch port stops
transmitting frames causing phone to unregister |
|
Network Statistics does not
display Port 1 or Port 2 status information |
|
7971 - PPU workaround does not
set forced link speed correctly |
|
7971 - change CDP from a mgmt
packet to a mcast packet in ATU |
|
7971 - enable VLAN 1 and VLAN 0 |
|
Phone unexpectedly shutdown
with in half an hour ,when XML boundary objects script was |
|
Phone unexpectedly shutdown for
200 calls per device case |
|
7970 won't boot w/ inline power |
7905/7912
TFTP Client Busy Retry Behavior |
|
7912 doesnt display correct
Softkeys when using MCDN feature |
|
IP Phone 7905 not responding to
http commands |
|
7912 cant ring immediately when
receiving a call after fallback |
|
MWI will be turned off by
incoming call |
|
7905/12 display English prompt
at Services page |
|
7912 ignores
StationClearPriNotifyMessage from CME |
|
Authentication delay between IP
Phone 7905 and CM 5.0 is to long |
|
Issues with processing of DNS
packets |
|
7912 RTP URI push during call
requires user to cycle hook twice to end |
|
7912 dies when configuring
Graphics via TFTP on CCM 4.1 |
|
During cross upgrade, power
off/on the phone & the phone never come up |
|
Found dtmf digits fail when
calling into Meeting Place IVR. |
7920
BSSID is all Zeros in
Reassociation Packets |
|
Site Survey Detail Shows the
Same Info for All APs Sometimes |
|
7920 Does Not Answer IGMP Query |
|
7920 Could Get Into Continuous
Roaming Loop When CU Is High |
|
7920 May Get 1 Way Audio
Without ARP-Caching |
|
7920 Will Sometimes Show RSSI =
1 |
|
Packets are Sent at 1mbps rate
Off Call When 7920 Uses a Non-Auto Rate |
|
7920 Advertises All Rates Are
Supported When Non-Auto Rate Is Configured |
|
Get association timeouts
sometimes with Aruba APs |
6608
6608 Fa Relay debugs in D00404
firmware need to be same as D00403 |
|
6608 inbound call mistaken for
hookflash |
|
ICMP Hard error handling |
|
Dicktracy Remove unnecessary DSP
and MLPP related messages. |
|
6608 Dicktracy Reduce trunk
flash timer from 700ms to 400ms. |
|
Burst of static during ringback
and connect on calls through 6608 |
6608/6624
Integrate 4.3.25 DSP firmware
for 6608 |
6624
6624 FXS port is unavalable for
2 mins after disabling and enabling |
|
updation on 6624 does not
reflect on port configuration page. |
|
FAC tone played continuously on
using non default network locale |
File
Versions included in 4.1(3)SR6:
Versions: |
|
AdministrativeReportingTool.exe |
4.1(0.46) |
ASTIsapi.dll |
3.3.2.0 |
Aupair.exe |
4.1.3.20019 |
AuthFilt.dll |
4.0.0.0 |
BulkAdministrationTool.exe |
5.1(4d) |
CallBackService.exe |
3.3.2.3 |
ccm.exe |
4.1.3.24626 |
CcmServRtmtPlugin.exe |
4.1.100.1332 |
CiscoAttendantConsoleClient.exe |
1.4.1.246 |
CiscoCTLClient.exe |
2.1(222) |
CiscoJTAPIClient.exe |
2.1(3.27) |
CiscoMessagingInterface.exe |
4.1.3.10026 |
CiscoTSP.exe |
4.1(1.4)ES12 |
CmiPerfMon.dll |
|
CPidMgr.exe |
3.0.0.0 |
ctftp.exe |
4.1.3.20013 |
CtftpChangeNotify.dll |
4.1.3.10054 |
CTIManager.exe |
4.1.3.20025 |
CtiMgrPerfMon.dll |
|
DBConvert.dll |
4.1.0.11 |
DBL.dll |
4.1.3.20009 |
DBLRT.dll |
4.1.3.20008 |
DBLX.dll |
4.1.3.10034 |
DNASetup.exe |
4.1(3)ES |
InsertCDR.exe |
4.1.3.20018 |
IPMAAssistantConsole.exe |
14.0.0.162 |
Ipvmsapp.exe |
4.0.0.19 |
IpVms.sys |
4.0.0.25 |
MADirectory.dll |
1.0.0.1 |
MediaAppPerfMon.dll |
|
QRTFileMgr.exe |
4.1.3.10080 |
RisDC.exe |
4.1.3.10057 |
RISX.dll |
3.3.0.2 |
SnmpCcmImpl.dll |
4.1.1.2 |
SOAPISAPI.dll |
4.1.3.10083 |
SSAPIDLL.DLL |
4.1.3.10025 |
tcdsrv.exe |
1.4.1.13 |
TcdSrvPerfMon.dll |
|
TCDSvrDBCN.dll |
|
ToolforAutoRegisteredPhonesSupport.exe |
5.1(4b) |
TftpPerfMon.dll |
|
UpdateLoadInfo.exe |
4.1.0.11 |
UserPermissions.dll |
4.0.0.0 |
Firmware Versions included in 4.1(3)SR6
Firmware |
4.1(3) Devpack 64 |
7914 14-Button Line Expansion Module |
S00105000300 |
Analog Access WS-X6624 Load |
A00204000012 |
ATA18X |
ATA030203SCCP051201A |
|
C00104000002 |
Digital Access WS-X6608 Load |
D00404000030 |
IP Phone 7902g |
CP7902080002SCCP060817A |
IP Phone 7905g |
CP7905080003SCCP070409A |
IP Phone 7906 |
SCCP11.8-3-3S |
IP Phone 7910 |
P00405000700 |
IP Phone 7911 |
SCCP11.8-3-3S |
IP Phone 7912g |
CP7912080003SCCP070409A |
IP Phone 7920 |
cmterm_7920.4.0-03-02 |
IP Phone 7921G |
CP7921G-1.0.4 |
IP Phone 7935 |
P00503021700 |
IP Phone 7936 |
cmterm_7936.3-3-14-0 |
IP Phone 7937 |
apps37sccp.1-0-1-0 |
IP Phone 7940/7960 |
P00308000700 |
IP Phone 7941/7961 |
SCCP41.8-3-3S |
IP Phone 7942/7962 |
SCCP42.8-3-3S |
IP Phone 7945/7965 |
SCCP45.8-3-3S |
IP Phone 7970/7971 |
SCCP70.8-3-3S |
IP Phone 7975 |
SCCP75.8-3-3S |
IP Phone 7985 |
CMTERM_7985.4-1-4-0 |
Media Termination Point WS-X6608 |
M00104000005 |
Determining the Software Version:
You can
determine the version of Cisco Unified CallManager software that is running on
your server by accessing Cisco Unified CallManager Administration and then
clicking Details.
The
following information displays:
· Cisco Unified CallManager System
version
· Cisco Unified CallManager
Administration version
· Cisco Unified CallManager
Installation ID
· Database information
Compatibility Matrix and Supported Upgrades:
You can
find the minimum versions with which Cisco Unified CallManager release 4.1(3) has
been tested and which previous release of Cisco Unified CallManager has upgrade
support by accessing the following URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/ccmcomp.htm
Note: Be aware that the release of Cisco IP telephony products does not always coincide with Cisco Unified CallManager releases. If a product is not compatible with Cisco Unified CallManager, you must wait until a compatible version of that product becomes available before you can upgrade to this release of Cisco Unified CallManager. For the most current compatibility combinations and defects, refer to the documentation that is distributed with the Cisco IP telephony products.
Locale Installer for Cisco Unified CallManager:
For optimal performance, be sure
that you use the Cisco IP Telephony Locale Installer that is specific to the
version of Cisco Unified CallManager that you use. Be aware that all
phrases may not display in the desired locale when you upgrade to a different
version of Cisco Unified CallManager. Refer to the readme file that is
posted with the Cisco IP Telephony Locale Installer software on the following
URL for the complete list of supported languages: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/locinst/index.htm
Each release of Cisco Unified CallManager
may support a different number of locales. The full suite of Locale Installers
that work with each applicable version of Cisco Unified CallManager can be
found on http://www.cisco.com about 8-10 weeks after the English version becomes
available. You can download the Locale Installers for all languages that are
supported with Cisco Unified CallManager from the following location: http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml
Note: When using locales, Cisco recommends that you wait until the locale installer that specifically supports the version of Cisco Unified CallManager that you use becomes available before you upgrade your system. Because some incompatibilities may exist between releases, be sure to only use the locale installer that specifically supports your version of Cisco Unified CallManager.
For additional
information about Cisco Unified CallManager,
refer to the following documentation:
Release
Notes for Cisco Unified CallManager Release 4.1(3) Refer to the following URL
for maintenance release notes that are relevant to this release of Cisco
Unified CallManager:
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/4_1/rel_note/index.htm
Cisco
Unified CallManager
Document Guide Refer to the following URL for a list of documents that are
related to Cisco Unified CallManager release 4.1(3): http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/4_1/index.htm
To access
the documentation suite for voice products, navigate to the following
URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/
To access
the latest software upgrades and related documentation for
Cisco Unified CallManager, navigate to the following URL and then choose the
applicable version: http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml
Cisco documentation and additional
literature are available on Cisco.com. Cisco also provides several ways to
obtain technical assistance and other technical resources. These sections
explain how to obtain technical information from Cisco Systems.
You can access the most current
Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website
at this URL:
You can access international Cisco
websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Cisco documentation and additional
literature are available in a Documentation DVD package, which may have shipped
with your product. The Documentation DVD is updated regularly and may be more
current than printed documentation. The Documentation DVD package is available
as a single unit.
Registered Cisco.com users (Cisco
direct customers) can order a Cisco Documentation DVD (product number
DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
http://www.cisco.com/en/US/partner/ordering/
http://www.cisco.com/go/marketplace/
You can find instructions for
ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation
in these ways:
o Registered Cisco.com users (Cisco
direct customers) can order Cisco product documentation from the Ordering
tool: http://www.cisco.com/en/US/partner/ordering/index.shtml
o Nonregistered Cisco.com users can
order documentation through a local account representative by calling Cisco
Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere
in North America, by calling 1 800 553-NETS (6387).
You can send comments about
technical documentation to bug-doc@cisco.com.
You can submit comments by using
the response card (if present) behind the front cover of your document or by
writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco Product Security Overview
Cisco provides a free online
Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform
these tasks:
· Report security vulnerabilities in
Cisco products.
· Obtain assistance with security
incidents that involve Cisco products.
· Register to receive security
information from Cisco.
A current list of security
advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt
If you prefer to see advisories
and notices as they are updated in real time, you can access a Product Security
Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this
URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Cisco is committed to delivering
secure products. We test our products internally before we release them, and we
strive to correct all vulnerabilities quickly. If you think that you might have
identified a vulnerability in a Cisco product, contact PSIRT:
· Emergencies security-alert@cisco.com
· Nonemergencies psirt@cisco.com
We encourage you to use Pretty
Good Privacy (PGP) or a compatible product to encrypt any sensitive information
that you send to Cisco. PSIRT can work from encrypted information that is
compatible with PGP versions 2.x through 8.x. Never use a revoked or an
expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key
server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also
reach PSIRT by telephone:
· 1 877 228-7302
· 1 408 525-6532
Obtaining Technical Assistance
For all customers, partners,
resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance.
The Cisco Technical Support Website on Cisco.com features extensive online
support resources. In addition, Cisco Technical Assistance Center (TAC)
engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
Cisco Technical Support Website
The Cisco Technical Support
Website provides online documents and tools for troubleshooting and resolving
technical issues with Cisco products and technologies. The website is available
24 hours a day, 365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco
Technical Support Website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a user ID or password, you can
register at this URL: http://tools.cisco.com/RPF/register/register.do
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.
Using the online TAC Service Request
Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service
requests are those in which your network is minimally impaired or for which you
require product information.) After you describe your situation, the TAC
Service Request Tool provides recommended solutions. If your issue is not
resolved using the recommended resources, your service request is assigned to a
Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or
if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or
S2 service requests are those in which your production network is down or severely
degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service
requests to help keep your business operations running smoothly.
To open a service request by
telephone, use one of the following numbers:
Asia-Pacific:
+61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2
704 55 55
USA: 1 800
553-2447
For a complete list of Cisco TAC
contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service
requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1) Your network is
down, or there is a critical impact to your business operations. You and Cisco
will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2) Operation of an
existing network is severely degraded, or significant aspects of your business
operation are negatively affected by inadequate performance of Cisco products.
You and Cisco will commit full-time resources during normal business hours to
resolve the situation.
Severity 3 (S3) Operational
performance of your network is impaired, but most business operations remain
functional. You and Cisco will commit resources during normal business hours to
restore service to satisfactory levels.
Severity 4 (S4) You require
information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products,
technologies, and network solutions is available from various online and
printed sources.
· Cisco
· Cisco Press publishes a wide range of general
networking, training and certification titles. Both new and experienced users
will benefit from these publications. For current Cisco Press titles and other
information, go to Cisco Press at this URL: http://www.ciscopress.com/
· Packet magazine is the Cisco Systems
technical user magazine for maximizing Internet and networking investments.
Each quarter, Packet delivers coverage of the latest industry trends,
technology breakthroughs, and Cisco products and solutions, as well as network
deployment and troubleshooting tips, configuration examples, customer case
studies, certification and training information, and links to scores of
in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/packet
· iQ Magazine is the quarterly publication from
Cisco Systems designed to help growing companies learn how they can use
technology to increase revenue, streamline their business, and expand services.
The publication identifies the challenges facing these companies and the
technologies to help solve them, using real-world case studies and business
strategies to help readers make sound technology investment decisions. You can
access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine
· Internet Protocol Journal is a quarterly journal
published by Cisco Systems for engineering professionals involved in designing,
developing, and operating public and private internets and intranets. You can
access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj
· World-class networking training is
available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html
© 2007 Cisco Systems, Inc.
All rights reserved.