Cisco
Unified CallManager Device Package 3.3(78.0)
Release Notes Version 12
These Device Package release notes
contain important information about installation procedures and resolved
caveats for Cisco Unified CallManager Device Package release 3.3(78.0).
Note:
Before you install this Cisco Unified CallManager Device Package, Cisco
recommends that you review the “Important Notes” section for
information about issues that may affect your system.
Determining the Software Version
Compatibility Matrix and Supported Upgrades
Important Notes & Recommendations
Resolved Caveats for Cisco Unified CallManager Device Package
Locale Installer for Cisco Unified CallManager
Cisco Product Security Overview
Reporting Security Problems in Cisco Products
Obtaining Technical Assistance
Cisco Technical Support Website
Definitions
of Service Request Severity
Obtaining Additional Publications and Information
This document provides installation
instructions for this Cisco Unified CallManager Device Package and endpoint
related changes.
Note: Failure to follow installation instructions as described
may result in inconsistent Cisco Unified CallManager behavior.
Make sure that you install and configure
this release of Cisco Unified CallManager on approved Cisco hardware. You can
access the correct Cisco-approved server configuration at the following
URL: http://www.cisco.com/en/US/products/hw/voiceapp/ps378/prod_brochure_list.html.
You can determine the version of Cisco
Unified CallManager software that is running on your server by accessing Cisco
CallManager Administration and then clicking Details.
This Cisco Unified CallManager Device
Package release is compatible with the following Cisco Unified CallManager
versions.
3.3(5)sr1 |
Note: Review the history file in your Cisco Unified
CallManager in order to determine what Device Package you currently have
installed. If you are preparing to install an older Device Package than is
currently on your CallManager, you will receive the following error “This
Device Package is older than the Device Package already Deployed. It is
recommended that you should exit now. EXIT now?”
NOTE: Be aware that the release of Cisco IP telephony
Endpoint firmware: http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser Endpoint documentation, including release
notes: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/english/
Cisco Unified CallManager
Device Package 3.3(78.0) includes the following firmware versions:
Firmware |
3.3-Devpack-78 |
Installation
Wrapper Name On CCO |
3.3(5) |
|
|
Analog Access WS-X6624 |
A00204000012 /
A0034322 |
|
ATA-18x |
ATA030203SCCP051201A.zup |
|
|
C00104000001 /
C002E031 |
|
Digital Access WS-X6608 |
D00404000029 /
D0054322 |
|
Digital Access+ Load |
D00303010033 |
|
Media Termination Point WS-X6608 |
M00104000004 /
M002E031 |
|
IP Phone 12 S |
P00203010100 |
|
IP Phone 12 SP |
P00203010100 |
|
IP Phone 12 SP+ |
P00203010100 |
|
IP Phone 30 SP+ |
P00103010100 |
|
IP Phone 30 VIP |
P00203010100 |
|
IP Phone 7902g |
CP7902080002SCCP060817A.sbin |
|
IP Phone 7905g |
CP7905080002SCCP060817A.zup |
|
IP Phone 7906 |
SCCP11.8-2-2SR1S |
|
IP Phone 7910 |
P00405000700 |
|
IP Phone 7911 |
SCCP11.8-2-2SR1S |
|
IP Phone 7912g |
CP7912080002SCCP060817A.sbin |
|
IP Phone 7920 |
CMTERM_7920.4.0-03-00 |
|
7914 14-Button Line Expansion Module |
S00105000200 |
|
IP Phone 7935 |
P00503021600 |
|
IP Phone 7936 |
cmterm_7936.3-3-13-0 |
|
IP Phone 7940/7960 |
P00308000500 |
|
IP Phone 7941/7961 |
SCCP41.8-2-2SR1S |
|
IP Phone 7970/7971 |
SCCP70.8-2-2SR1 |
Note: It is very important to disable platform agents and services,
such as NetIQ and Prognosis performance monitoring, Cisco-verified antivirus
services and intrusion detection software, remote management services, and any
other monitoring applications that automatically restart services; this action
ensures that your system does not encounter issues that are associated with
these services.
Cisco provides the following guidance to help you successfully
install and/or upgrade Cisco Unified CallManager software:
·
To minimize
call-processing interruptions during the upgrade process, make sure that all
servers are running the same version of Cisco CallManager software before beginning this
upgrade.
·
Make sure that the servers
are online before you begin this Device Package installation; otherwise,
pre-upgrade checks may fail or return faulty information.
· For optimum performance/security, apply the most current OS
upgrade and SR before you install the Cisco Unified CallManager Device Package. For more information, refer to Cisco IP Telephony Operating System, SQL
Server, Security Updates at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/osbios.htm.
·
If you are using Cisco
Unified CallManager Security Agent, you must DISABLE this software and then
restart your system before you proceed with this installation.
· All nodes in
the cluster run through a database replication check during the upgrade process
as an extra measure, even though the publisher's database replication check
should catch any replication errors clusterwide.
If you encounter a warning message on any node during
this check, make sure that you stop the installation process and check the log
files. Follow the recommendations listed below if the log file displays any of
the following messages:
·
“All
agent-implementing jobs are waiting to start”
·
“At
least one agent-implementing job is attempting to execute after a previous
failure“
·
“At least one
agent-implementing job has failed to execute successfully“
·
Be sure to DISABLE any
antivirus and intrusion detection software, along with any other security
services; then, restart your server before you run the upgrade process. You must manually re-enable these services
after the installation is complete.
·
Make sure that you disable the following Cisco-verified
platform agents and applications; these products may interfere with the Cisco
Unified CallManager installation:
Ø
Server management agents
Ø
VOIP monitoring/performance monitoring
Ø
Remote access/remote management agents
Note: It is very important to disable platform agents and services,
such as NetIQ and Prognosis performance monitoring, Cisco verified antivirus
services and intrusion detection software, remote management services, and any
other monitoring applications that automatically restart services; this action
ensures that your system does not encounter issues that are associated with
these services.
Note: To verify that the installation completed successfully, follow
the instructions in Step 5 in the Installation
Instructions section.
Note: Cisco recommends that you apply this Device Package during a
maintenance window.
Procedure
NOTE: Apply this patch to all of your
Cisco Unified CallManager servers, beginning with the publisher server and TFTP
server.
When applying this Device Package to enable new device support, a
cluster-wide reboot is required for those devices to register
successfully. A clusterwide reboot IS NOT required when running to
update existing firmware/support.
If installing on Cisco Unified CallManager 3.3(5)sr1a, the
following message will be displayed: "Install on Publisher and TFTP server
is required. Installation on all nodes is highly
recommended." A clusterwide install/reboot is not required.
If installing on Cisco Unified CallManager 3.3(5)sr2 (recommended), the following message will be displayed: "Install on Publisher and TFTP server is required. Installation on all nodes is highly recommended." A clusterwide install/reboot is required.
Perform the
following procedure to install Cisco Unified CallManager Device Package X.X.exe:
Download the ciscocm-3-3-DevPack-X.X.exe
file to your hard drive. Make a note of the location where you saved the file.
1.
Double-click on the downloaded file to begin the installation.
2.
Click Yes when the installation process
displays a message that asks if you want to install this Device Package.
3.
The remainder of the
installation process continues without any additional user input.
4.
Towards the end of the
install it will prompt you "Update ALL devices firmware defaults?",
(IMPORTANT) If you click "yes", it will change the default firmware
load for all devices to the latest load packaged with this device pack, click
"no" if you want to change the loads manually yourself later.
Note: In order to change the loads
manually, you do NOT need to reinstall this Device Package. The new files will
be present in the C:\Program Files\Cisco\TFTPPath folder. Go to
CCMAdmin->System->Device Defaults and manually change the name of the
load file (for specific device(s)) to the new load and click UPDATE. Next,
reset the affected devices for them to upgrade to the new load.
The system will ask you if you want to view the logfile when the installation
is complete.
5.
Verify that the
installation completed successfully by taking the following actions:
a. When the system prompts you to view the
log file, if the number of errors listed in the dialog is "0", you
can select No.
b. If the number of errors detected was greater than 0, select Yes to view the logfile and scroll down to the end of the log file. The errors section at the bottom of the log file will be updated with a corresponding severity.
c. Reset affected devices in order for
them to obtain new firmware loads, or reboot the cluster.
Note: If the TFTP server is a separate server from the Publisher, the
Cisco TFTP service needs to be stopped and restarted on the TFTP server before
performing this step, unless the cluster (including the TFTP server) is being
rebooted.
Change the device defaults for devices you wish to roll
back. From the Cisco Unified CallManager Administration page go to
System/Device Defaults and set the devices that were changed previously back to
their previous firmware setting. Select update, and then reset those
devices.
The system may create or edit the following log files during the
installation process:
·
c:\program
files\common files\cisco\logs\CCMPatch\Cisco Unified CallManager X.X
DevPackXX Installation YYYY-MM-DD HH.mm.log (this file is also
accessible by navigating to the Start menu shortcut "Cisco Install
Logs" under the CCMPatch folder)
·
c:\install\dbinstall\dbinstallXXX.txt
·
c:\program
files\common files\cisco\logs\CCMPatch\sqlX.txt
·
c:\program
files\common files\cisco\logs\history.log
This Device Package includes the
following resolved caveats:
3.3-Devpack-78 |
|
Phone Directory gives incorrect details
after upgrade to 8.2.2 |
|
Adding THX and Babylon5 features |
|
Checking in latest dictionary file for third
generation phones. |
|
7940/60 |
|
Animated circle (reset icon) seen
continuously in a scenario |
|
Add new icons for sidecar to support Muster
release |
|
7960 not allow to select 2nd call of a
conference call on shared line |
|
A call picked up is not recorded in
'Received calls'. |
|
Upgrade LSC menu strings not flushed on
moving out of tht menu. |
|
7960 stops sending CDP packets - causes do1x
error disable switch port |
|
Phone remain in Configuring IP state even
with proper DHCP response |
|
Option 66 preferred over option 150 based on
appearance in DHCP ack. |
|
7960/40 skinny do not detect handset with
failover to SRST |
|
Unicode Special Characters blacked out on
7940 and 7960 SCCP phones |
|
Several call progress tones need to be
louder |
|
Secure Conferencing Icons for Muster |
|
7960 phone does not calculate srtp
authentication tag correctly |
|
Placed call list shows '*' for FAC enabled
calls |
|
Secure SCCP Phone Conference Initiator
Crashed on Hangup |
|
7940 ph does not accept new req after
rejecting invalid IP address req |
|
7960 SCCP does not play beep tone when DND
incoming alert is configured |
|
Phone temporary rejects HTTP connection when
its sockets are available |
|
Static, white noise heard w/ 7960 7940
logging into unity with G729 |
|
Update Cisco Logo on phone web pages |
|
Update the copyright year to 2007 on the
boot display for the mid-range |
|
7940/60 not streaming sometimes when using
encryption |
|
StreamingStatisticsX reports phone as idle
when call is active |
|
IP phone at remote offices stuck in opening |
|
6608 |
|
6608- Cleanup code to make room for few more
fixes |
|
6608- debug enhancements |
|
6608 T1 CAS ports are getting marked as OOS |
|
6608 Gateway gets unregistered after
resetting MGCP Backhaul port 2428 |
|
6608 MTP port intermittently unregistered |
3.3-Devpack-77.1 |
|
7936 Phone Displays Host not found when
accessing corporate directory |
|
7906/7911/7941/ |
|
7961/7970/7971 |
|
TNP- keyboard I/O errors on reset |
|
7970 phone in low power mode consumes more
power than CDP advertisement |
|
Phones failover to secondary node with wrong
cause code |
|
Network Locale Version backwards
compatibility |
|
Third gen phone may behave wrong under
stress registration test |
|
3g-phones -- pick up Sun Java patch to
address 2007 DST changes |
|
Hung RS-232 port
causes phone upgrade failure |
|
7971/7941 re-append parameters with a
redirected authentication |
|
SIP Phone goes for a reset when proxy
address name starts with _ |
|
7914 configured over 15 digit in line number
behaves very strange |
|
phone UI Locks up when adjust Speaker Volume
during registration w/ BLF |
|
phone resets after warning out-of-chunks for
memory tracking |
|
third gen phones power is initally set high
power at boot w/line powered |
|
3rd gen phones running 8.0(4)SR1 unable to
adjust ringer after a call |
|
u7961/41/70 stuck at requesting after phones
inbound web access disabled |
|
PNG Broken- Phone fails HTTP GET if earlier
HTTP request is not finished |
|
Caller-id is not updated correctly for
conference calls |
|
After flash reformat phone gets flash
Programming failure errors |
|
Retrieving a parked conference call,
disconnects the call |
|
Memory Leak on phones with repeated calls
with very short call hold time |
|
Pressing New Call should let user Enter
Number |
|
Bugtrap 0x91 phones (during fsck) |
|
Composed IPPM messages display + instead of
space |
|
Unknown name displayed if special characters
are in display name |
|
Exit softkey stops UI when in Security
Configuraiton/CTL File submenu |
|
TNP phones on CME can't resume call with
Line button |
|
Phone crashed running Codenomicon SIP test
4913 |
|
unable to do cfwdall if kpml is enabled in
sip-srst mode |
|
SIP phone failed to clear Held call when CCM
restarted |
|
make 'DEBUG' trace anticipated for a 1-way
audio problem as NOTICE trace |
|
Customer is experiencing one way audio calls |
|
SenderJoins & Byes values were different
regardless of call status |
|
GUI stuck after changing contrast |
|
Osage- Phone drops incoming unicast EAPOL
when VVLAN is present |
|
Call duration timer window on ph display
cycles between multiple calls |
|
call tranfer after cfw noan on tnp sip phone
failed |
|
Incorrect Date header value in SIP REGISTER
request |
|
Idle sftkeys displayed on new incoming call
after transferw/rel image |
|
AutoObjInFocusIf.getLabel returns incorrect
information for a call item |
|
Response.Redirect fails |
|
Need to Press Right button twice on Nav Pad
to close Line Detail |
|
IP Phone SSH Vulnerability |
|
Filesystem Privilege Escalation |
|
Internal calls are having one way audio |
|
Filesystem Denial of Service |
|
OnHook Dialing from Line2 doesn't work if
Line1 and Line2 have same DN |
|
Phone doesn't calculate SRTP auth tag
correct for certain RTP payload |
|
Bug trap 91 if TCP server/client resides in
the phone |
|
Stutter Tone quality problem when using
speaker / line button |
|
Focus does not shift to off-hook line while
another call is incoming |
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
Factory Reset require for secure phone to
move to another CCM |
|
IP-phones hang when call arrives while
XML-play in progress |
|
Phone displays CM down in a active call
during failback |
|
Large increase in PNG graphic processing
time |
|
7961 phone not show Help info for privacy
button |
|
SIP Phone needs to also detect non-localized
Conference |
|
Number stored in missed calls not updated
upon receipt of SIP UPDATE |
|
Not able to Set CallFwdAll on tnp sip phone
in particular scenario |
|
No dial tone is heard after togglling the
hookswitch in ring out state |
|
Read linenumber from the config file |
|
TNP SIP sometimes sending malformed to or
from header |
|
7970 sip sends invalid presence subscription
causing high CPU |
|
Focus should remain on oldest ringing call
with mulitple incoming calls |
|
Failed on multipl forward from SIP phone to
SCCP phones |
|
tnpsip phone doesn't light up blflamp when
destination press callfwdall |
|
Phone crashes when messages hard button is
hit. |
|
Call not forwarded after
CTINewCallAcceptTimeOut on SIP TNP phone |
|
CallHistory Menu- line key, speaker key, no
longer work |
3.3-Devpack-76 |
|
CM 3.3 misleading has Video Capabilities
enable option in 7970/71 config |
|
Install unconditionally Reinitializes
replication |
3.3-Devpack-75 |
|
Merging local dictionary in CCM |
|
7935/36 |
|
Scheduled software download on NEs failing |
|
7936 with CCM 5.0 displays Server Not Found
when access Corporate Dir |
|
7936- Can gain access to web interface w/o
admin password |
|
7936 does not register G.729a capability
along with G.729 capability |
|
Selecting Tone Test and exiting hangs phone |
|
Setting up Admin VLAN id brings up the phone
without a DN |
|
7936/35- Ignore CDP V1 message for VLAN
configuration purposes |
|
7936 phone hangs when pressing hold &
resume |
|
7935 does not recover after power/network
loss |
|
7936 phone shouldn't release its VLAN until
the TTL(CDP message) expired |
|
UI displays Failed to set VLAN Idwhen changing
n/w setup in activecall |
|
When we dial the DN through web page
,message flashes for sec & proceeds |
|
7935/6 reboot using corporate directory
search on 3'rd party LDAP server |
|
7935 does not register G.729a capability
along with G.729 capability |
3.3-Devpack-74 |
|
Beep tone max power is only -22dBmO |
|
FSCK stuck in deadlock with syslogd |
|
DSP Configuration Files are not Correct |
|
Enumeration Pattern Code Updates |
|
Phone sends corrupted RFC2833 packets when
SRTP enabled for call |
|
Dev Studio changes to make building Communicator
easier |
|
Secure phone does not retrieve the SEP file |
|
7931- Call Plane Detail View is not open
after On-Hook dialing |
|
CiscoIPPhoneStatusFile LocationX parm not
used for small image size |
|
Commit of CSCef34402 broke c6slc, other?
pikespeak images |
|
Titan dsp host could 32-bit read between dsp
firmware two 16-bit writes |
|
Osage- Max Input Rxd msg displayed when 32
chars input to Shared Secret |
|
Power Save Configuration options missing in
Settings |
|
Osage- Status Messages for 802.1X
Authenticatio not as per Osage UI spec |
|
softkeys disappear after blind directory
transfer |
|
TNP- keyboard I/O errors on reset |
|
RTCP- Exiting Hoot & Holler cause phone
to send bogus BYE packet |
|
7931- Exception in OverviewModel during
restart |
|
Support G.722 56k and 48k in the Audio
Server |
|
TNP phone logs "Unable to get
memory" message on console |
|
pressing volume key then speaker button can
lock up phone |
|
G.722 K-Factor Table incorrect |
|
Highlighted Call isn't displayed if 10th
call ended leaving 9 held calls |
|
7970/7961- dtmf burst is played with a
double duration |
|
Phone does not send un-register message to
SRST on fallback to CCM |
|
7931- Pressing Line button does not change
Line focus |
|
Onhook dialing produces delay in feedback
sound with last digit |
|
IP phone fails to do HTTP authentication |
|
7931- Overview not in home position at
initial bootup |
|
RTCP socket open error may cause audioserver
to spin |
|
under is only 20 chars instead of 64 |
|
Dynamic Trace level registration results in
file create/delete operation |
|
EAP-Request/MD5 to PC supplicant could not
pass thru Gig phone |
|
Static Analysis Codebase Cleaning on Select
Files |
|
7961 phones not processing CTI request to
disable softkey |
|
TNP- dhcpRcv.c - uninitialized variable |
|
7970- Phone lock up when message URL has max
or 255 character |
|
IP Phone should re-DHCP immediately after
DHCP NAK |
|
7931- scroll up and down, sometimes a
leftover icon appear next to label |
|
show inventory command returns no data |
|
RTCP- SDES packets are not being padded
correctly |
|
Idle Prompt for SRST cannot be set back to
the default value |
|
Phone not sending DHCP traffic to pc port |
|
Unable to dial from external dir list after
cancel edit dial |
|
LCD display does not always show status of 3
consecutive lines |
|
7911G experiences loss of registration |
|
SIP phone show "Connected" in call
preservation if user in/out line disp |
|
7961 with voice vlan resets if IPC is
connected to 3rd vendor switch |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Ringing phone ICON keep showing up on the
phone display without call |
|
Skittles- Retain Dialplan from CCM while
failing over to SRST |
|
IP phone not direct HTTP request to proxy
server w/ unresolved DNS name |
|
Phone does not have "End Option"
field with DHCP Release message |
|
Incorrect DSP Configuration File Formats |
|
RTP Tx URI request should be rejected when a
call is active |
|
|
|
3rd gen phones running 8.0(4)SR1 unable to
adjust ringer after a call |
|
When uri is not responded by user, second
uri post just hangs forever |
|
Clean up debug options available / messages |
|
Line DN label appear to be shifted a pixel
or two to the left on Display |
|
Digit tone improperly continues until call
connect |
|
JPN hone freeze at Cisco Logo after reset
due to Java OutOfMemory error. |
|
7961/70 fail to transfer a call with line 2
from Directory |
|
TNP- Remove NULL term from hostname in DHCP
request |
|
7971 displays "Ethernet
Disconnected" briefly |
|
Phone core dump when terminating mulitple
calls |
|
phone not fallback to CCM and shows
"Restarting...". |
|
Enumeration Pattern Code Update |
|
Mute Button is enabled when Phone Speaker
Button throws Error pass Limit |
|
On turbo the overview is distorted when a
new call is created and ended. |
|
Osage- Transaction Status does not update
unless menu is re-entered |
|
TNP SIP phone uses wrong default TLS port
number |
|
Handsfree Receive Frequency Response does
not meet the mask |
|
debugsh- set LOG_DEBUG trace level for
sunvm.cnuw/ debug SIP/JVM command |
|
Phone does not detect Invalid Load Server IP
address for "A.B.C D" |
|
Phone Ringsin Continuously,Need to power
off/on to clear the call |
|
7911 SLR is 5 dB softer than required, its
ok in GL mode |
|
IPPM- Phone displays XML Parse Error when
accessing Contact List |
|
7961 - PC cannot see data traffic if PC
Voice VLAN Access is disabled |
|
TNP SIP phone can not handle long Unicode
callid/linetext |
|
7931- Clean up OverviewModel
ACTIVATE_REQUEST event handler |
|
Osage- Phone drops incoming unicast EAPOL
when VVLAN is present |
|
7970 Runs out of memory as phone when idle
URL is used |
|
7931- Phone looses softkeys when exit from
IDLE URL screen |
|
Incorrect values in RX/TX_START_TIME and/or
REPORT_TIME pegs |
|
TNP phones on CME can't resume call with
Line button |
|
Focus does not shift to off-hook line while
another call is incoming |
|
Soft factory reset does not clean files from
/etc/sfr.tab |
|
RTCP- With RTCP disabled web StreamingStats
Report Times are invalid |
|
Include Kernel.core into the sylog files for
debug purpose |
|
Not able to use Dial Sofkey in Corporate
Directory |
|
TCP not sending all posted data after socket
close |
|
7911/41/61/70/71 - 2 concurrent XML posts
result in Error 0 or Error 6 |
|
devoplement build (TNP) script does not work |
|
Dial Softkey should be disabled for
corporate directory/PAB/FastDials |
|
Turbo- DoS tool icmpsic crahses phone on
Bugtrap 0x93 |
|
Unmount Error |
|
offhook w/ handset for the first time after
reboot, no dialtone is heard |
|
HTTP sessions are not currently aged-out |
|
CreateStringMatchProperty does not update
the allowedValues |
|
TNP - 7911 phone needs an 802.1X port lookup
mechanism |
|
9 lines with call in Hold Reversion, phone
stops ringing |
|
provide for next generation static analysis
for TNP |
|
RTCP- BYE packet has padding bit mistakenly
set |
|
7941/7961/7970/7971 Aliasing in high band
when using wideband headset |
|
7931- LineFullDisplay detail is missing from
the title |
|
Call History Enhancements for Chumbawamba
Phase 1 |
|
7970- reduce msg sizes being used in network
daemon IPC |
|
Static Analysis Codebase Cleaning on Select
Files |
|
When calls are selected/unselected, sorting
is done immediately |
|
TNP - 7971G-GE forwards 802.1X packets twice |
|
Exit softkey stops UI when in Security
Configuraiton/CTL File submenu |
|
7931- May have a Java Memory leak in
disposeDynamicFeature |
|
Static Analysis Codebase Cleaning on Select
Files |
|
IP phone stuck at Cisco Logo screen when
reset from CCM w/ sidecar |
|
Can not login to phone during automation
testing |
|
Network Locale Version backwards
compatibility |
|
support persistent status line display on
SIP phone in SRST mode |
|
Phone throws exception upon going off-hook |
|
Dial URI w/ Active Call doesn't Invoke Call
Options when no app in focus |
|
Static Analysis Codebase Cleaning on Select
Files |
|
7931 Titles in Line FullDisplay aren't left
aligned at at the same place |
|
Phone continues to ring after shared line
picks up a transfered call |
|
mipspacker not use CNU versioning for BN2
image |
|
7931- Line number overlayed with ellipses
... while in active call |
|
7970 SCCP requires Authorization when
hitting **# to unlock the phone |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Phone Service unavailability message
corrupted |
|
UDI Time Zone not displaying string from
phone config file |
|
7931- Handsfree RLR does not meet the spec |
|
Phone not showing "Duplicate IP
Adress" in status line |
|
HOST Field Send IP Address Instead of
Defined Hostname |
|
7911 Phone speed and duplex settings not
saved |
|
CP-7971 does not cache TFTP address if
option 66 set TFTP server name. |
|
TNP phone sends
StationSubscriptionStatReqMessage at restart |
|
Focus changes to the new ringing call before
10 secs.. |
|
Reset on sleep mode phone would not put it
back to sleep mode |
|
CiscoIPPhoneDirectory/DirectoryEntry/Name
should be restricted to 32 cha |
|
TNP- check return value when writing
dhcp.conf |
|
Remote in use calls with no caller ID should
display "To Unknown Number" |
|
Sanity- Core produced for rtsp on restriciting
incoming bandwidth/bitrat |
|
Fragile file cleanup and performance
enhancements (Jasmine featurette) |
|
7931- Tuk Tuk noise heard while using
wideband codec for a call |
|
7970 Phones have incorrect active display
during shared line call |
|
SIP phone should reattempt download of
softkey&dp on TFTP down/ timeout |
|
For Cbarge "CM down,features
disabled" message not displaying on 7970 |
|
7931- Headset icon not displayed when
Headset LED is pressed |
|
Expand Directory object name field to accept
64 characters |
|
7931- Softkeys disappear with 4 sofkey
templates |
|
7971 should set Audio Preference to default
values after Erase |
|
Muffled voice on receive for some calls |
|
cnu recover second look |
|
7911- GroupPickUp does not work |
|
Unknown name displayed if special characters
are in display name |
|
7970-DHCP- Rejects DHCP request with option
15 from CNR |
|
Display on shared-lines not-in-call is not
consistent in cBarge scenario |
|
7931- Incorrect call appearance on shared
trunk monitor calls. |
|
Call Focus shifts to Held call for
consultative conference call leg |
|
TNP - Soft factory reset should clear 802.1X
PAE info |
|
7931- Enable video support |
|
Focus is on wrong call when line view is
opened indirectly |
|
Change the 7906 BN2 to use RELEASE keys for pilot
build |
|
Turbo should not advertise G.722 |
|
Dynamic features like BLF Speed dial and
Privacy are not working |
|
Call fails when no dialplan and registered
to SRST |
|
Conference on Alerting with 8-0-2-4S load |
|
Update 7911 diagnostics to version
10.02.00.06 |
|
CNU kernel BugTrap 0x91 with V-E-R-Y
specific conditions |
|
TNP phone stuck in blank screen during
upgrade to 8.0(3) load |
|
third-gen phone 8.2(1) recover process is
not displayed |
|
dsp ingress frame timestamp not following
RTP RFC3550 |
|
sleep() system call not POSIX compliant |
|
AbbrDial key shouldnot be active when
speakerbutton is disabled |
|
Text Item Displays are not right justified
in RTL locales |
|
Phone should explicitly turn on display when
reset/lost registration |
|
SIP phones should Ignore unknown softkey set
names in softkey xml |
|
7931- Add icons to the DetailsFullDisplay |
|
CIA-680 Support on 3rd gen phones |
|
revertPriority setting not used for 1st call
after changing the setting |
|
Third-Gen phones running 8.0(3) do not hear
multicast audio from RTPMRx |
|
8.2 phone load causes robotic issue at
customer site |
|
Dialplan is not supported when Failover to
SRST |
|
Highband noise reduction tuning |
|
Bugtrap 0x91 phones (during fsck) |
|
unable to disable kpml on TNP phone
registered to CME |
|
TNP- send DISCOVERs if no DHCP server can be
found |
|
IP phone reset with DOS attack |
|
7941/61 LCD controller must be reset at
startup time. |
|
Arabic locale missed QRT on dest info |
|
Empty Dial list is getting displayed on
phone |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Default router entry removed when dup ip
present |
|
Can not press line 36 on 7970 with 2
sidecars |
|
7931- Unable to answer call on 2nd line
using phone handset |
|
"On " prompt doesn't always work |
|
Static Analysis Codebase Cleaning on Select
Files |
|
TNP- "show inventory" CLI output
not adhering to the specificication |
|
redial sk is not active in onhook state |
|
getEndPointInfo reports MWI setting
incorrectly |
|
vm -mem broken on Broadcomm platform
(7941/61, 7970/71) 8-2-0-20 |
|
LCD display shows status of Lines 22-24 after
phone boots up not 1-3 |
|
Turbo- DHCP recv socket error on bad address |
|
SenderJoins & Byes values were different
regardless of call status |
|
Osage- 7961GE stops receiving EAP-Req/ID
during long duration reset test |
|
Static Analysis Codebase Cleaning on Select
Files |
|
7931- Doesn't show IDLE display on phone
display after restart from CME |
|
TNP phone fails to display the switch info
at its webpage |
|
7970-PNG image file download crashes the
phone |
|
SYN ACK messages from phone not DSCP tagged |
|
Jphone- Navigate problem under network
statistics menu when debug mode |
|
make property retrieval from RMS store file
effecient |
|
Handsfree SLR does not meet the spec |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Add volume control for local and network
tone |
|
7931- Speed dial does not display called-id
when another line offhook |
|
Selective graying out of AudioPref menu
items incorrect on inline power |
|
Need to Press Right button twice on Nav Pad
to close Line Detail |
|
Placed calls are not multi-party and should
not show a MP call history |
|
Phone Continuously displays
"Requesting...". |
|
Softkey wrong after fallback from SRST |
|
7961 (and 7941,7970,7971) doesn't display
Call park number after getting |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Static Analysis Codebase Cleaning on Select
Files |
|
7931-UI shows lines 22-24 when line button
pressed with AppMenu Open |
|
Settings -> Device Configuration -> UI
Configuration menu is missing |
|
Call History Lists inaccessible after having
max entries and deleting 1 |
|
7931- Phone restart from CM duration test
leads to Disk full |
|
Add SIP related changes to support G722 for
ph0 of wide world |
|
Missing Pixels on the left side of UI
displays on Turbo phones |
|
phones should not advertise Voice VLAN on PC
port |
|
JTest- SIPCCAdapter.java switch statement
missing breaks |
|
7931- Factory Reset Walk LED pattern is only
16 |
|
7971 phone reverts to old config after
changes saved to netwk config |
|
debugsh should support RTCP trace |
|
7931- LEDs for lines above 8 do not
illuminate |
|
Cfwdall fails to come back on CCM after
fallback from SRST |
|
7914 displays old version of remote-in-use
icon |
|
Line LED not lighting up or delayed on
incoming calls |
|
Phone display not turned on when going into
reverting state |
|
TNP SIP Phone resets after auto register due
to default load info missin |
|
PNG Broken- Phone fails HTTP GET if earlier
HTTP request is not finished |
|
Pushing RTPRx or RTPMRx URI to phone in a
call enables mute |
|
Call Statistics menu- Sender size is not a
correct format |
|
SIP phone UI Locks up and Keypresses ignored
(still registered w/ CCM) |
|
UI locks up & phone cannot register |
|
Timer Exception seen in TimeDateRequest |
|
Clear softkey does not work in Status
messages screen |
|
Outgoing ringing and incoming ringing tones
played at same time |
|
apply patch for Diab compiler from WindRiver |
|
Add new tone messages to make
traditional/stutter tones selectable |
|
Phone accepting duplicate IP |
|
Static Analysis Codebase Cleaning on Select
Files |
|
7911, 7906,7931 & 7921 have poor voice
quality with G711alaw codec |
|
Out of Memory - Connection refused errors
after duration testing |
|
Turbo- 1st incoming call can't be answer if
2nd one be connected first |
|
RTCP- RR/SR packet is missing some info when
there is 2 report blocks |
|
SIP gives different Error message than SCCP
in Locations scenario |
|
7931- IDLE URL Refresh timer doesn't work in
66DEV image |
|
Write to the TNETV105x PCNTRL "Access
Control Reg" must be 16 bit |
|
Shared line display & going offhook
while in active call distort display |
|
TNP- libcso.map from build should be saved |
|
New Features - Auto Call Select and More Key
Timer |
|
7931- Leave 1 pixel space w.r.t. App
Menu/Headset/etc |
|
Line reports as unregistered, but it's not,
after failover |
|
Re-sync tone table if dsp host re-starts |
|
Phone not retrying the re-IP after dup IP |
|
Phone core dump while running the call
features automation script |
|
7961/41 Speaker LED on even after pushing
End key |
|
SETTINGS softkey does not work if no DHCP
server available during bootup |
|
mount command exiting with status code 64 |
|
KATE Input causes NPE and non-password data
while using XML services |
|
u7961/41/70 stuck at requesting after phones
inbound web access disabled |
|
SCCP phone does not register back to
publisher after restart. |
|
Need an API to assign a local port to TLS
connect |
|
LineModel dispose call throwing a
ClassCastException |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Dialer does not close correctly after Cancel
or Idle Timer Expires |
|
Need filter coeficients for headset, handset
and speakerphone |
|
TNP Phone 7941 second line line button will
light up for incoming call. |
|
Static Analysis Codebase Cleaning on Select
Files |
|
Multi-Party Call History - Transfer case -
Received call "from" details |
|
Audio Server K-Factor table for G.722 |
|
CNU Flash Filesystem not recoverable if it
fills up |
|
certcnu.bin
failure- GETCNU- CNU image update failure; code = 10 |
|
Status of BLF SpeedDial does not get
updated. |
|
need feature parity between sip and sccp
phone for speed-dial |
|
Endcall softkey doesn't work in Call
Preservation |
|
Answer and DnD Softkeys are not always
displayed when a call is rcvd |
|
Idle sftkeys displayed on new incoming call
after transferw/rel image |
|
7970 precedence call waiting tone does not
stop |
|
softkey disappears on the phone after
several calls are made |
|
Issue with Pegs when the call is remotely
held and on MOH |
|
wrong filepath used after posting a TFTP
file |
|
Phone should send the 433 Anonymity Disallowed
for anonymous calls |
|
Diagnostic is alway reloaded into the
primary slot |
|
Turbo- Speed dial entries not at designated
position |
|
Calling/Called Info not correct for SIP TNP
phones |
|
Double call sort after ending selected call |
3.3-Devpack-73 |
|
Adding 8.2(1) features to CCM 3.3, 4.1, 4.2,
5.0 |
3.3-Devpack-72 |
|
Link 'View the User Guide for your phone'
not available for 7961/794 |
3.3-Devpack-71 |
|
No web access cfg option for 7941/61 in CCM
device donfiguration page. |
|
6608 E1/T1 |
|
6608 T1 cas channel rejects outbound calls |
|
7902/7905/7912 |
|
Phone response status inconsistent between
models |
|
7912 phone should not send
StationFeatureStatReq if feature is not confi |
|
7905Japanese characters are shown as ?s in
EM screens |
|
CP-7912 can not use 255 as last octet of
SRST address. |
|
IPICS Channel selection by select key does
not work intermittently |
|
DnD fails on 7912s |
|
7912 w/alt tftp disabled does not read TFTP
server from DHCP |
|
7912 can not resume multiple calls from hold |
|
Connection Monitor Duration changes not
applied to 7902 |
|
7912 cannot make new call after lisfting
handset |
|
Malformed XML Delieverd from 7912GA when
using DeviceInformationX |
|
No response to UserToDeviceData for Key: xxx
URI passed from CTI |
|
Init: CallHistory URI does not re-set status
line on 7905 |
|
call waiting tone doesn't stop when the
second call hangs up. |
|
7912 prefixes fastdial with 'undefined' |
|
7912 affected by ARP storm |
|
7912 authentication problem - password
encoding |
|
IP Phone Service problem with 7912 http
redirect v8.0 |
|
Able to Change Ring Volume Even when Setting
Access set to Disable |
|
7912G-A phone does not obtain address when
voice vlan = access vlan |
|
CIA 650: Randomize TimeDateReq's to Call
Manager from 7905/7912 |
3.3-Devpack-70 |
|
6608 PRI Gateway stayed up even when CCM
lost connection |
|
Link 'View the User Guide for your phone'
not available for 7961/7941 |
|
7940/7960 |
|
Build phone loads |
|
JPN-Cancel softkey not available for
configuring 7960+7914 |
|
phone displays Select Ringer... for Invalid
DistinctiveRing.xml |
|
UI screen is grayed out when i-button is
pressed |
|
Autodial cancelled is shown for a Phone in
RingIn state |
|
Phone displays AutoDial Cancel in transfer
scenario |
|
7960 tries fallback to CCM that has CCM
service shut but port 2000 open |
|
Phone Softkey should be greyed out for
Disable Speakerphone and Headset. |
|
7960 produces garbled audio and repeated
words for PA Help |
|
Softkeys within various Settings submenu not
responding if held |
|
DN not displayed in a hold scenario after
line button press. |
|
Init-CallHistory URI does not re-set status
line on 7960/7905 |
|
Phone displays Callmanager parameter as
UNDEFINED to boot up process |
|
revertPriority = Even fails when Hold
Reversion call is oldest |
|
Integrate DSP rev 4.0(2) |
|
parked calls get loud tone when picked up
from 7960/40 on CME 4.0 |
|
Callback can not be activated for a busy
extension |
|
Abbreviate dialing should not be available
if phone not able to call |
|
need to press line button twice to answer an
incoming call |
|
Mute light stays on after audio broadcast is
complete |
|
ST- 7960 secure phone got TLS error with
SRST after CCM 4.2.2 upgrade |
|
one way voice when the timestamp field in
the RTP packets rolls back |
|
RTP Tx URI request should be rejected when a
call is active |
|
7960 does not differentiate local hold call
and remote hold call |
|
40/60 - LA dev size grown above acceptable
size limit |
|
7960 with voice vlan resets if IPC is
connected to 3rd vendor switch |
|
phone doesn't handle the DHCP next server
field and option 66 correctly |
|
7960 displays XML error on hitting
directories button with French locale |
|
Phone hangs with HIGH CPU detected- during
EM logout & locales installed |
|
6608 E1/T1 |
|
6608 PRI Gateway stayed up even when CCM
lost connection |
|
6608 shows wrong OID |
3.3-Devpack-69.2 |
|
7935/36 |
|
Phone Button does not work |
|
7936 with 4.2SR1 cannot dial digits when in
call state 3 (Ring Out) |
|
Scrolling to the end of the line in EditDial
causes 7935/7936 Reboot |
|
7936 not passing DTMF while in alerting
state. |
|
DTMF tone will not play for consecutive same
digits with 7936 |
|
Display is not uniform when dialing an non
existing number |
|
Mute dosen't work with |
|
Phone dosen't ring while viewing the MAC
address details using **6 |
|
7935 and 7936 do not support 40, 50, and
60ms frame sizes |
|
Phone displays In Use Remotely with out
shared line in SRST mode |
|
LED Status changes when the Transfer softkey
is selected in SRST mode |
|
7935/36 need to support the priority field
in DisplayPriNotify message |
|
Polycom 7936 doesn't refresh after saving
the Alt TFTP address |
|
Main/Secondary TFTP Address cannot be
modified when DHCP is disabled |
|
Conference not working on 7936 in SRST mode |
|
7936 Phone does n't allow/display full
domain name. |
|
7936/7935 does not support JOIN feature of
CCM 4.0 |
|
7935 |
|
Renumber 7935 firmware load name to match
the CCO versioning |
|
6608 T1/E1 |
|
After Standby SUP boots up seeing Duplicate
SA ID detected in database |
|
Router identify a very short DTMF as a valid
DTMF |
|
MGCP backual message with length of 12 bytes |
|
6608 PRI Gateway stayed up even when CCM
lost connection |
3.3-Devpack-69.1 |
|
Merging local dictionary in CCM |
3.3-Devpack-69 |
|
7940/7960 |
|
7960 phone does not clear status line during
reset |
|
pressing line button on ipphone doesn't
switch between detail &overview |
|
Posting Line34 URI enables Line30 on ip
phone. |
|
7960- Does not preserve the state of
mute/spkr button in handset mode |
|
7960 drops the incoming call when using the
IPICS services. |
|
7960 phone does not handle HTTP code 401 for
push request |
|
Phone- Authentication username/password
takes only 31 characters |
|
CiscoIPPhoneInput takes * and # when input
is set to N |
|
StreamingStatisticsX not backwards
compatible |
|
7960- Call being on hold is NOT sorted by
Select function |
|
7960- Doesn't update CDP cache when no voice
vlan present in CDP message |
|
7960 DSP Logging utility broken |
|
7960 does not display via |
|
IP reassembly broken |
|
IP phones become unregistered from both SRST
and CM |
|
7960/7940 phone stuck at CONFIG IP after a
reset/power cycle |
|
Phone load Upgrade to 7.2(3) causes RXshort
errors on PC port |
|
Phone drops untagged PC Traffic |
|
HTTP 100 Continue from phone malformed |
|
Remove use of linked directory in SCCP BA |
|
7960 - XML Debug PUSH behaves erratically |
|
Handle Current Call missing when dialing
from Directory |
|
Phone rejects menu responses from server-
Fastdial, Corp Dir |
|
Callback notif (Dial) & Park while
already in an active call fails. |
|
GARP enable/disable ignored |
|
The phone crashes when it receives invalid
Response.ContentType in HTTP |
|
Secure Phones does n't cancel tftp request
while cancel key is pressed |
|
7940/60 PC port 100M does not receive
network traffic intermittently |
|
7960/7940 Rcvr Lost Pkt reports as a
negative no under impairement |
|
Unable to dial the CB notified number during
ringing state |
|
No sidetone during first phone call
following phone registration |
|
Phone performs unneeded ARP when Garp
enabled |
|
Phone removes ARP entries too quickly |
|
help for settings button not displayed when
setting key is disabled. |
|
DHCP enabled Phone resets with held call
when alternateTFTP changed |
|
Phone doesn't display held call in detail
view when barged call ends |
|
Promts is Truncated to 20 Characters when
using Greek Locale |
|
Phone resets if we dial Half of the DN
on-hook & remaining off-hook |
|
Speed dial from Monitor DN is not working
with 7.2.2 |
|
phone display Remote-In-Use menu when the
other end resume the call |
|
DIALED Number missing in CFA where the
target phone is 7940/60 SCCP |
|
Update 7960 built-in font to include new
zero with a slash |
|
7960/40 cannot register in autheticated mode
CCM 4.1.X OS 2000.4.2 |
|
Phone resets during high bandwidth traffic
to PC |
|
Placed calls are recorded on all shared line
phones |
|
Missing SpeedDials on phone after upgrading
the phoneload |
|
7960 crashes when more than 20 calls placed
via stress script |
|
Placed call list under directory gets
updated only for Connected calls |
|
7960- Unable to reset phone when other
shared line is busy |
|
Phone strip dialed Number in Directory
Placed call list for PSTN call |
|
7914 |
|
Implement SeaDragon feature |
|
|
|
3.3-Devpack-68.1 |
|
7906/7911 |
|
7906/7911Check in
7906/11 f/w load to CCM |
|
7935/7936 |
|
DTMF tone will not play
for consecutive same digits with 7936 |
3.3-Devpack-68 |
|
Make 7906 (turboprop) appear in device
defaults and device pulldown FCS |
3.3-Devpack-67.5 |
|
device
defaults do not update properly in 3.3(5)es41 |
3.3-Devpack-67.4 |
|
CCMAdmin should not offer option of 72XX
voice platform as a MGCP GW |
|
ENU
Coltrane3.0 Check In For English-US Locale |
|
CIA-680
Support on 3rd gen phones |
|
Call
History Enhancements for Chumbawamba Phase 1 |
|
7920 |
|
Coltrane 3.0 Firmware Check-In |
3.3-Devpack-67.3 |
|
ENU
Coltrane3.0 Check In |
3.3-Devpack-67.2 |
|
7920 |
|
Extension Mobility does
not work with Services URL Button on 7920 |
|
7920 Doesn't Support
Vibrate URI |
|
Need a menu to display
configured regulatory domain |
|
Need a menu to display
current transmit power |
|
7920 Does Not Support CCA
Versions of QBSS |
|
7920 can spontaneously
re-register to CM in idle with INF-MIB error |
|
7920 Can Associate to a
Lower Priority Profile When Set to Auto Profile |
|
Upgrade to 2.0 will cause
phone lock password corruption |
|
Port 17185/udp is open on
7920 phone |
|
7920 RTPMTx sets TTL of
sent multicast packets to 1 |
|
7920 call-forward noan on
second active call results in phone hanging |
|
7920 can corrupt the CCKM
Timestamp |
|
Invalid XML object sizes
can cause the 7920 to reboot |
|
Idle URL can cause the
7920 to lock up |
|
7920 will roam off a
strong signal AP to a weaker one |
|
7920 should continue
streaming RTP packets when on Mute |
|
7920 can fail to ACK G711
packets during a call |
|
7920 Can Roam More
Frequently With 12.3(7)JA AP Image |
|
7920 Can Stop Scanning
Although Still Associated |
|
7920 send 802.11 Auth
suddenly and it causes choppy audio |
|
Channels in Active List
are not flushed after 3 missed CM Keepalives |
|
Emergin's alert tone
volume needs to be limited when on-call |
|
CP-7920 is not responding
to AP packets |
|
MWI tone can be very loud
to user if CP-7290 re registers |
|
Need to roam when QBSS
max threshold is met |
|
7920 MR2.0.1 firmware
upgrade |
|
7936 |
|
Cannot use # or * as
first entry while onhook |
|
7936 vulnerable to ICMP
attacks |
|
7936 doesn't send HTTP
Get with multi tier DNS names in Directory URL |
|
Can't place a call from
phone book when it receives a missed call |
|
Phone cannot be resetted
to factorydefault when Admin paswd is not known |
|
Remote party hears echo
when 7936 used in glass conference room |
|
7936 accepts invalid IP
Address and Subnet mask |
|
7936 accepts invalid
Alternative TFTP Address |
|
Access Admin Setup
without entering the passcode |
|
Conference not working on
7936 in SRST mode |
|
Web interface allows to
change password with different characters |
|
7936 Web Interface allows
different characters in Phone Book |
|
7936 Web interface
dosen't prompt for password when phone is restarted. |
|
7936 phone retains the
meetme session even after the call manager fails |
|
phone may not give Error
tone when incorrect phone number dialed |
|
7936 Editing phone Book
doesn't have the asterisk in the required field |
|
If call received while
editing ring tone and publisher fails, 7936 hangs |
|
7936 Web interface
accepts alphabets in |
|
Phone will not accept
incoming call while waiting for |
|
7936 Takes long time to
register when PINGED with CCM failover |
|
Info for |
|
Polycom 7936 doesn't
refresh after saving the Alt TFTP address |
|
Polycom 7936 allows to
change the Ringer settings in Ringin state |
|
Phone book entry on the
web display is not proper |
|
7936 reboots when you
configure Admin VLAN id while in active call |
|
7936-Call Transfer number
is not displaying in SRST mode |
|
Park Information retained
for a long time. |
|
DN not displayed while
placing the call on hold & initiating a new call |
|
Call initiations fails
from the phonebook with CFwdAll |
|
Phone registers with Alt
TFTP when Alt TFTP Address not specified. |
|
Phone hangs when used
Diagnostics with CCM failover |
|
Mute turns off in this
scenario in 7936 version 3-3-7-0 |
|
Second Call on shared
line cannot be resumed or muted |
|
7935 & 7936 Polycom
phones lockup on failover, loss of call preservation |
|
Display issue when
Meet-Me number is 10 digit |
|
Phone does not accept to
change the passcode with valid characters |
|
ncorrect display on one
of the phone in sharedline |
|
Incorrect LED status on a
phone in shareline with call waiting enabled |
|
7936 Transmit Jitter
Extremely Sporadic - 2 Second Cycle |
|
7936 won't fallback to a
TFTP server once registered to an SRST router |
|
7936 Phone use odd RTP
port numbers |
|
7936 phone with phone
load 3-3-8-0 does not work for FAC |
|
7936 Outside dial tone
sounds the same as inside dial tone |
|
Call gets disconnected if
we press hold & resume multiple times |
|
7936 does not play tone
50 (Zip) when someone joins a conference |
|
Phone display is
incorrect when a bogus phone load is entered. |
|
Phone dosen't ring when
**8 is executed |
|
Phone hangs during
failback and failover with meetme |
|
Phone displays
Registering after CCM failover in a active call |
|
Dial tone stops when
phone receives a missed call |
|
Digital Access WS-X6608 |
|
6608 - Incorrect marking
DSCP value to 0 |
|
6608 shld not
automatically clr connection when ICMP unreachable is rcvd |
3.3-Devpack-67.1 |
|
7911- Add support for
Vieo |
|
ITA- Display of Zero and
CAPS O - 7960 Font Display |
3.3-Devpack-67 |
|
Placeholder CDETS for Turboprop Feature Commit |
3.3-Devpack-66.3 |
|
Placeholder CDETS for Turboprop Feature Commit |
3.3-Devpack-66.2 |
|
7941/7961-7970/7971 |
|
no value for some items on Device INformation page |
|
Phone should display ... for very long Text or Number |
|
SSO Standby RP T/B atm_ha_decode_vc_update+0x23c for ATM
PVC bundle |
|
Phone registered to a CM 3.3 shows only one line while
call on hold |
|
Received and missed calls show wrong calling party number |
|
Time stamps on console messages and phone display is not
the same |
|
Deselected call in sorted call list appears with other
selected calls |
|
Turbo Gabage at the end of Network Statistic screen |
|
Cancel softkey has delayed response when looking up a
bogus DNS addr |
|
Phone resets wmore volume of call are placed on sidecar
lines |
|
wbm failed to extract signature when display filter was
used |
|
Turbo Can not remove Doamin Name on phone |
|
Phone does not remove the default router config |
|
Increase max CPU usage timeout for JVM process |
|
SIP TNP 1.1 image stress run freezes phone UI |
|
Phones unable to Rx or Tx Multicast Services when
Publisher fails. |
|
Phone w/200 calls active single line reset w/calling phone
reset |
|
dhcp.conf could have invalid my name entry |
|
Add consolle trace to indicatie the call is an encripted
call |
|
Phone doesn't register when it is unable to resolve the
CCM name |
|
paging group display delayed on 7911 with CME |
|
get SW port returned -1 error after downgrade to 6.0(2)SR1 |
|
Phone stops playing multicast after an unanswered call |
|
local Ip/port value is cleared but others are kept for an
ended cal |
|
LED does not blinking red while the DCP is busy |
|
7970/7971 Touch Screen issue IP Phone URL shows Delay |
|
logins with sys group permissions on release signed phones |
|
Skittles timeZone tag errors |
|
Turbo Background Image thumbnails not displayed in correct
order |
|
7961 Row of Pixels missing on Line View graphic |
|
Skittles phone locks up when SEP dateTimeSetting is empty |
|
Skittles phone locks up when SEP dateTemplate is MM/DD/YY |
|
Phone display goes blank for consult transfer to busy
monitor line |
|
when PickUp softkey is pressed on onhook phone displays
??? |
|
Sittles Service URI cause phone to crash |
|
need to press mute twice for an incoming intercom call |
|
Assign a same IP port to RX and TX socket - casues 1 way
audio |
|
Phone doesn't play Zip/ZipZip Tones toward network |
|
Phone Rcvr Lost Pkt reports as a negative no under
impairement |
|
SIP TNP DSP debug seen when pressing Settings,
Directories, or Services |
|
Reference getPegs() via IMedia interface instead of
directly |
|
Turbo Phone receives mcast pkts when port open forMcast
transmit |
|
Turbo Error Verifying Config Info after LSC install on
secure phone |
|
README-SGM-pdsources on DVD has SGM references |
|
Phone Should handle gethostbyname failure and print
appropriate Err Msgs |
|
Phone not displaying all Placed call list when pressing
up/down button |
|
Corporate directory search fails if username contains
special characters |
|
wirelss client to client can not pass traffic |
|
Service URL feature assigned in em profile does not work |
|
Phone sends Duplicate DHCP Discover Message |
|
Phone freeze after reset stress |
|
Phone displays wrong msg when registration rejected for
security reason |
|
phone doesn't show up old admin vlan id in Current Admin.
VLAN Id |
|
Corporate Directory Search Fails When using Russian Locale |
|
Add Title to Line View to identify which line the calls
belong to |
|
Having directory menu open causes Callback to not working
properly |
|
Exit soft key is not working in Callback Screen |
|
HTTP CGI ModeInfo query does not return if Services URL doesn't
resolve |
|
Ethernet Disconnected Mesasge does not appear when
Ethernet unplugged |
|
Turbo Missing status messages on Load Server parameter |
|
No status message when TFTP service is down on load server |
|
LineInfo web age query does n't show up Messagewaiting
Indication. |
|
Phone won't failback to a TFTP server once registered to
an SRST router |
|
HTTP req canclled msg when hitting a softkey |
|
Japanese locale (td-sip.jar) not loading on SIP phones. |
|
Removing JVM from 7.0 on 8.0 CPK files (to avoid out of
space errors) |
|
Turbo status message No Default Router after changing
DHCP=no to yes |
|
Phone does not preserve the state of mute/spkr button in
handset mode |
|
Skittles phone does not complain with junk value in
displayOnDuration |
|
Making DSP standalone on phones- dsp.cnu reads dspfw.bin |
|
select image Userpreference->Background image display
invalid png icon |
|
CDP crashs from broadcasted CDP pkt, results in restart of
all apps |
|
Privacy lamp is not being displayed correctly on 7941 SCCP
phone |
|
add fault-tolerance to filesystem |
|
Phone unable to come out of Service Menu using CANCEL
softkey |
|
Phone responds to CDP triggers from upstream port |
|
phone does not play precedence CW tone |
|
Calls drop during CME failback |
|
Phone is stuck if Encrypted Config is on and supporting
load is absent |
|
phone doesn't come up with DHCP enable when Voice VLAN =
Access VLAN |
|
Incorrect response for unicast/invalid IP adress for
RTPMTx i p URI |
|
CiscoIPPhoneExecute ExecuteItem priority 1 is ignored in
some cases. |
|
Invalid Ip Address to be displayed while validating Null
values. |
|
Turbo lost audio w/ 100% broadcast traffic |
|
Status Msg timestamps changed between 24hr/12hr formats on
reset |
|
CP-7970 firmware version 7.0(1) distorts background image
color |
|
Softkey changes from Connected Transfer state to On Hold
state |
|
Phone is loosing the querystring parameter on the refresh |
|
Phone Multicast services not working |
|
LSC Installed Status Messages is not displayed on phones |
|
cBarge Target phone changes focus when other party cBarges |
|
Phone doesn't dial from placed call listwhen editdial&
dial is pressed . |
|
Phone Displays UI with no keys for a shared line scenario. |
|
Phone CGI URLs never complete HTTP transaction |
|
Services page text does not display properly |
|
Idle phones never send SCCP TimeDateReq to sync clock |
|
Pressing the '.' soft key in the edit menu doesn't force
Kate String T/O |
|
Clicking noise is heard in encripted call when duplicating
packets |
|
Phone plays garbled audio for PA prompts |
|
phone displays ??? as Codec in Call Statistics window |
|
Call Stats window displays wrong info for Rcvr Lost
Pkts/Discarded |
|
IP Phones use random UDP source port for RTP media |
|
Phones stop sending KA when backup TCP link down |
|
call bubble does not disappear when there is no active
call |
|
High End Phones connect to CCM sub that is not present in
the CTL file |
|
Turbo fine-tune displaying errors of dspSendFrame
_framePutEgressFrame |
|
Turbo InsideDialTone could not be stopped after removing
CFwdAll |
|
UDI Support |
|
Turbo Codenomicon HTTP test 39730 causes sunvm CPUTime
Limit Exceeded |
|
Add core file decoded core file to the serviceability
webpage |
|
SIP phone loads and CCM are out of sync for PC Voice VLAN
Access |
|
GARP enable/disable reversed |
|
Property Errors - Settings Can Be Lost |
|
phonerebooting when secondary CME inaccessible and
keepalive is 10 |
|
Enhance the flush operation in the RecordStore |
|
HTTP Client locks up upon consecutive posts to CGI Execute |
|
No prompt/status in Detail call history record |
|
Dial Softkey Enabled when no Active Audio Path or no CCM |
|
Erase from Top-Level Settings Menu does delete sidecar
contrast |
|
SIP Phone does not do a TLS session reuse after network
failure |
|
RMS Store must be deleted in order for phone to boot
correclty. |
|
Phone stuck after erase under Settings menu |
|
JPhone Overview displays incorrect topcall if some RIUs
made private |
|
GARP enabled native code returning incorrect value |
|
Phone could not recover after DNS entry be corrected |
|
Phone sends Invalid Message for SCCP v3 and v4 |
|
Phone Answer softkey not displayed for new icoming call |
|
Remote In Use Icon/LED not shown when shared line is
private |
|
HTTP Authentication Does not Show Response |
|
Able to Change Ring Volume Even when Setting Access set to
Disable |
|
TimeDateReq to sync clock causes KeepAlive to miss one
interval. |
|
7970/7971 InCorrect Date Format Shown Under Missed Calls |
|
2 meg file limit cause double boot when upgrading to 8.0
load |
|
JAVA/TNP Log/trace related changes |
|
CNU syslog changes for 7.0.2.x branch |
|
getportcfg check for errors on msgsnd() |
|
Display distorts, when held calls goes from three to two |
3.3-Devpack-66.1 |
|
ATA-18x |
|
ATA SCCP Incorrect Call Waiting behavior |
|
Conference to ATA-Phone thru H323 & ATA-phone on same
CME doesnt work |
|
ATA flooding callmanager with Softkeyevent New call skinny
messages |
|
Problem transfering calls using ATA and CME |
|
Update signaling ToS to be consistent with current design
guides |
|
ATA186 configuration web page should state clicking rather
than click |
|
ATA SCCP sent AVT message when sent DTMF to SCCP endpoint |
|
No Secondary dialtone played by ATA SCCP |
|
ATA186 excessive TCP ACK delay after receiving SKINNY
message |
|
ATA SCCP sends excessive StationSendTimeDateReqCSCef39491 |
|
Analog Access
WS-X6624 |
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
Digital Access
WS-X6608 |
|
Calls through 6608 T1 CAS trunks are not preserved |
|
T1-CAS E&M ports on a 6608 card unregistering during
stress test |
|
Periodic T1-CAS E&M channel out-of-service during 6608
stress test |
|
7940/7960 |
|
Phone without DHCP cant recover Dup IP address |
|
7960/7940 characters by pressing '0' with li-ffr.4-1-3-JPN
are funny. |
|
help symbol missing in text press - key to cancel for
english locale |
|
7960 Settings -> RingType menu changes doesn't take
effect |
|
7910 DSCP values need to be consistent with current design
guides |
|
EM logout restarts the IP Phone. |
|
Small MTU causes CVTA to H323 video call failure |
|
7960/7914 Ringer type off by 4 lines. |
|
Update dictionary file with SeaDragon new phrases |
|
Phone Continuously displays Requesting RingList File
...... |
|
Phone UI Lines separating the DN disappear as it failover
to subscriber |
|
Posting Line34 URI enables Line30 on ip phone. |
|
http ///CGI/CallInfo does n't display all lines call Info. |
|
ActiveSoftkeys eg redial, New Call are shown when pubisher
CCM is down. |
|
In CallInfo the CalledPartyName field is not proper for
Conf call |
|
In http request for CallInfo/LineInfo the Prompt field is
showing null |
|
Line button does not answer call with 2 calls on hold
already on line |
|
DHCPReleaseMessage should be unicast to DHCPserver,not on
broadcast IP. |
|
7960 Phone doesn't display blank URL sign or URL without
label on line |
|
Volume control keys when calling a busy no affects
ringer(ver 8.0(0.16)) |
|
7960 Phone reset from settings with **#** while on call
hold |
|
7960 Phone loose RTP stream when restart from CM |
|
7960 Pressing Line button twice ends calls on Phone in
ringing state |
|
BigApp does not kick back to LA on version mismatch in
XMLDefault.cnf.xm |
|
phone 7940/7960 should escape '#' symbol |
|
7960 doesn't receive MOH or DHCP when Voice VLAN = Access
VLAN |
|
RED LAMP indication on 7914 for In Use Remotely does not
work - 7.2(3) |
|
7960 MWI functionality should be consistent with current
phone behavior |
|
7960 Phone volume not being set properly at RTPRx start |
|
Menu object as IDL URL, menu item 1 selected when phone
goes off-hook |
|
MWI lamp glows continuosly after a CB notification for the
first set CB |
|
IP phones become unregistered from both SRST and CM |
|
Phone load Upgrade to 7.2(3) causes RXshort errors on PC
port |
|
Phone drops untagged PC Traffic |
|
Handle Current Call missing when dialing from Directory |
|
Secure Phones does n't cancel tftp request while cancel
key is pressed |
|
7940/60 PC port 100M does not receive network traffic
intermittently |
|
Unable to dial the CB notified number during ringing state |
3.3-Devpack-66 |
|
CM need support for new phones in devicelistx.asp file |
3.3-Devpack-65.6 |
|
Implement group listening. |
|
ES/SR Installation needs corresponding code for CSCsb44801
resolution |
|
Enlarge splashscreen in ES/SR
installaton |
|
Need new sections for file copy ops |
|
Update SQL script handling |
|
Remove support for 3.3(2) from 3.3 Device Package |
|
Enhance error handling reporting and dialogs |
|
End of installation Dialog Changes needed for Device
Package |
|
7902/7905/7912 |
|
7912 fails due to malicious VLAN tagging |
|
7912 does not play |
|
7905/12 phones lose Service button after EM update |
|
phone - 7912 phone reboots after receiving 3 IMs quickly |
|
Only a 7912 shared number phone work when configured
max-dn dual-line |
|
No dial tone after the 7905 and 7912 SCCP failover to SRST |
|
7912G-A phones cause PC's behind them not to retain an IP
Address |
|
Long delay for PC to obtain network connectivity when used
with 7912G-A |
|
7912/05 should always Reset unless an rtp stream is active |
|
CCCM 5.0 & 7905/12 does not show external number on
top line of display |
|
7912 SCCP sends excessive StationSendTimeDateReq in idle
mode |
|
7912/05 excessive TCP ACK delay after receiving SKINNY
message |
|
7912/05 RTPMTx sets TTL of sent multicast packets to 1 |
|
Timedate req. msg. storm from at midnight |
|
7911 |
|
Checkin 7911 f/w loads to create Device Packs for FCS |
3.3-Devpack-65.5 |
|
Update/Make 7911 ready for FCS and prepare Skate SR build |
|
7935 |
|
CP-7935 generates choppy audio when in a conference call |
3.3-Devpack-65.4 |
|
Need tag for 6608-MTP/CFB in ccm xml |
|
7936 |
|
7936 Transmit Jitter Extremely Sporadic - 2 Second Cycle |
3.3-Devpack-65.3 |
|
7.0(2)SR1 image for the 7941/7961 checkin to 3.3, 4.0 and
4.1CCM release |
|
7970/71 7.0(2)SR1 image check in |
|
7941/61 |
|
Phone freeze after reset stress |
|
Exit soft key is not working in Callback Screen |
|
CDP crashs from broadcasted CDP pkt, results in restart of
all apps |
|
Privacy lamp is not being displayed correctly on 7941 SCCP
phone |
|
add fault-tolerance to filesystem |
|
Phone responds to CDP triggers from upstream port |
|
phone doesn't come up with DHCP enable when Voice VLAN =
Access VLAN |
3.3-Devpack-65.2 |
|
CM need support for new phones in devicelistx.asp file |
3.3-Devpack-65.1 |
|
3.3(4) devpack 64 has wrong product_csv file for 7920xml |
3.3-Devpack-65 |
|
remove loggingDisplay option for 7941...7961G-GE phones
from CCM/Windows |
|
Logging Display and Load Server features do not appear for
the 7970/7971 |
|
7941/61 |
|
checkin 7.0(2) firmware for 7941/7961 phones into
CCM/Windows |
|
7970/71 |
|
7.0(2) firmware for 7970/71 |
|
6608 |
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
CallManager may incorrectly put a 6608 CAS port OOS |
|
6608Glare conditions on T1 CAS is not cleared
appropriately |
3.3-Devpack-64.1 |
|
7936/7935 does not support JOIN feature of CCM 4.0 |
|
EVM-HD-8FXS/DID module shows up as VM-HDA-8FXS/DID |
3.3-Devpack-64 |
|
Incorrect 2821 endpoint identifiers without MLA |
|
6608/6624 |
|
GW config page for cat6kT1 VOIP shows fields required when
optionl |
|
Change configuration fails to open the GWconfigpage over
securechann |
|
Clicking help in gatewaypage prevent users from viewing
device info |
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
CCM4.1.2 web page for Gateway device config should be
https |
|
6608 T1 CAS channels are stuck in CSCallClearing state |
|
Inactive channels are not busied out when 6608 loses CCM
registration |
|
6608 Lost packet counter is increased by 16 for every
press of DTMF tone |
|
6624 FXS ports stuck in offstate state / ReleaseInd Q931
state |
|
7935 |
|
7935 susceptible to ping attack, causing odd/delayed
behavior |
|
Using keys during call causes chopiness |
|
7935 loses connectivity on voice RTP broadcast packets
reception |
|
CP7935/CP7936 Does Not Support DTMF Out of Band |
|
7935s did not come back up after upgrade from Parche to
Skate |
|
After a CCM upgrade phone displays rebooting..... |
|
7935/7936 Phone does not support broadcast suppression |
|
Slow audible feeback for key presses |
|
TFTP Client Behavior - 2 TFTP Servers |
|
7936 freezes after on-hook dialing |
|
Phone requires power-cycle if publisher fails while Call
Waiting in prog |
|
Mute doesn't work on 7936 (Call waiting enabled) when
publisher fails |
|
7940/7960 |
|
Greyed ERASE softkey is actually enabled |
|
Caller ID gone from shared line after a barge |
|
>in 7940/60 i-button help text |
|
sidecar lamp shows red for barge/cbarged calls |
|
7960/40 Device Info page does not follow Message Waiting
Lamp Policy |
|
Display settings on Phone should be changed for Restricted
Display |
|
7960 can load a Ringlist.xml with more than 50 entries |
|
Remove conditional code |
|
IPPS authentication credentials, % sign not URL encoded |
|
PC can't ping 7960 phone with dot1p configured |
|
Next key not displayed for CiscoIPPhoneDirectory that
appears in Service |
|
ARP cache timeout if set 0 in 7960 phone flood the n/w
with ARP queries |
|
7960/7940 characters by pressing '0' with li-ffr.4-1-3-JPN
are funny. |
|
Build P0030701T018 ES Load |
|
30th digit of Speed dial display text is not properly
displayed |
|
7940/60 plays multicast from other VLANs as well as the
voice VLAN |
|
phone reboots after several hours of operation over high
delay network |
|
CDP code does not verify destination MAC address |
|
7940/60 Little App accepts DHCP Offer from a different
VLAN |
|
No Display for dialed number thru personal fast
dial/directory lookup |
|
Loader |
|
7960 Settings -> RingType menu becomes unresponsive |
|
Unwanted Debugs appear on Console |
|
* and # are causing settings softkey to be updated in
settings submenus |
|
7960 Line text Label contains garbage when sent to SRST
router |
|
Inconsistency in Streaming Stats between web page and
phone when MoH |
|
Second 7914 expansion module displays garbled characters |
|
7960 phone drop G.729b frames when silence suppression is
on |
|
7960 - DHCP broadcast for renewal instead of unicast at
50% lease time |
|
Setting menu Softkeys intermittently are not responding |
|
7940/60 sends AdminVVLAN in response to CDP Trigger with
VVLAN query |
|
Phone sends extra off-hook message |
|
PC connected to 7940/60 has slow network communication |
3.3-Devpack-63.4 |
|
PC logging option is not available for makaha |
|
7936 |
|
Using keys during call causes chopiness |
|
CP7935/CP7936 Does Not Support DTMF Out of Band |
|
7935/7936 Phone does not support broadcast suppression |
|
Slow audible feeback for key presses |
|
TFTP Client Behavior - 2 TFTP Servers |
|
7936 freezes after on-hook dialing |
3.3-Devpack-63.3 |
|
7911 QED changes to support alt scripts and load server |
|
CM 3.3 misleading has Video Capabilities enable option in
phone config |
3.3-Devpack-63.2 |
|
7920 user guide cannot be loaded from CCMUser pages |
|
Enable visibility of Makaha types in dev packs
3.3.5.eng.spec, 4.0.2. .. |
|
Checkin ip7961.pdf ver3 into3.3.5.eng.spec,
4.0.2.eng.spec, 4.1.2.eng... |
3.3-Devpack-63.1 |
|
Change configuration fails to open the GWconfigpage over
securechann |
|
Clicking help in gatewaypage prevent users from viewing
device info |
|
change configuration link is not opening for 6608 &
6624 GWs. |
|
CCM4.1.2 web page for Gateway device config should be
https |
|
Enable visibility of Makaha types in dev packs
3.3.5.eng.spec, 4.0.2. .. |
|
7961/7941 font should be more readable - suggest making
tallerCSCef28642 |
|
7910 |
|
7910 fowarded call display syntax error |
|
SD1C Phone firmware parses phone config file incorrectly |
|
Phones To Be More Ambitious Towards Updating Firmware |
|
Echo fades in and out when talking IP phone to IP phone |
|
Ip Phone doesnt accept option 66 with trailing dot in
hostname |
|
Slow performace when data AND voice vlan is tagged
(802.1q) |
|
Callwaiting does not work on 7910 ip phone |
|
Disabling settings w/o disabling ring volume |
|
Dial keys do not respond for 10 secs after pressing **# |
|
7940/7960 SIP phones not handle out of order/mis-sequence
packets |
|
Phone fails to come up when wrong load Id is mentioned on
phone page |
|
7960 send StationAlarm w/ incorrect text if no RegAck |
|
Faint audio is heard in the speaker while using handset |
|
Set Ringer Duration ignored by Seaview phone registd with
ParcheCCM |
|
7910 should not drop the 1st call by pressing line on 2nd
call |
|
An error at a certain key sequence |
|
7910 conf phone does not displays called/calling name |
|
Key rollover broken/missing digits when dialling |
|
C3PO Frame Buffer overflow causes COS3 packet drop |
|
Audio cut through delay during Call Waiting Answer |
|
7960/7940 Voice Quality Degradation With Echo Back To
Remote Party |
|
TFTP 2 address edit display contains garbage |
|
7910 ip displays connected call information wrongly |
|
7910 phone having DN of 24 digits reboots if CFA number
crosses 9 digit |
|
7910 phone does n't displays fwd for forwarded
intercluster call |
|
7940/60 handset/headset SRL/RLR mid-spec adjustment |
3.3-Devpack-62.2 |
|
7920 user guide cannot be loaded from CCMUser pages |
3.3-Devpack-62.1 |
|
7.0 firmware and associate files checked into CallManager |
3.3-Devpack-62 |
|
7920 |
|
IP phone services do not work |
|
Need Capability to Disable Configurable Menus |
|
7920 Should Be Less Aggressive for LEAP |
|
Softkey Templates Do Not Work with 7920 |
|
Duration fields are occasionally wrong in 802.11Data null
packet |
|
7920 does not support virtual carrier sensing |
|
7920 Red button cannot end call when far end busy |
|
7920 placed call log may not include discarded digits |
|
No Connectivity After Downgrade to 1.08 When Using Static
WEP |
|
Ringtones are displayed incorrectly when less than 4 rings
available |
|
7920 can change focus to another line when on call |
|
7920 user guide cannot be loaded from CCMUser pages |
|
Intermittent AP retransmissions if 7920 is unavailable |
|
7920 Sometimes Roams Unexpectedly Due to Packet Loss |
|
7920 can get stuck in a scanning state |
|
7920 does not look at source port for Multicast |
3.3-Devpack-61.1 |
|
1700 GWs FXO ports are allowed to be configured for diff signaling. |
|
PI6 based features commit to CCM branches |
|
support for VWIC2 on 26xx/36xx/37xx/38xx in 4.1.3 |
|
support for EM2-HDA-4FXO in CCM |
3.3-Devpack-61 |
|
pcm should handle csv files with linux based end of line
characters |
|
Turbo-Some line settings not available |
|
7961 Phone Icon missing in the Call Manager Find/List
Phones |
|
7.0 firmware and associate files checked into CallManager |
|
PI6 based features commit to CCM branches |
|
6608 |
CFB/MTP |
Tertiary CM not listed in Transcoder Device Configuration
Page |
|
6608 cfb unregisters after one missed keepalive |
|
conference bridge not getting registered to correct ccm |
|
ICMP Hard error handling
for 6608 MTP/CFB |
|
7912 |
|
7905/12 display English prompt at Services pag |
|
Issues with processing of DNS packets |
|
Settings Access restricted option behaves like enabled on
7912 |
|
7912 can not initiate hold w/ multiple calls per line and
shared lines. |
|
The browser window on the 7912 opens when it should not |
|
There is no dial tone when exiting from the directory menu |
|
7912 Chinese Locale-Unable to display calling number |
|
CHS-Wrong Phone display |
|
DTMF when users mash 7912 keys unrecognizable to AA/IVR |
|
7905/7912-Does Not Format '?' Characters in Services URL
Properly |
|
XML Error [4]-Parse Error on 7912G when creating FastDial
in PAB |
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
3.3-Devpack-60 |
|
ATA18X |
|
ATA has poor voice quality when NumTXFrames set with high
value |
|
ATA (SCCP) does not process Calling Party Name in second
CallInfo |
|
Issues with processing of DNS packets |
|
Unable to set UI password for ATA188 |
|
7902/05/12 |
|
7905/12 display English prompt at Services page |
|
Issues with processing of DNS packets |
|
Settings Access restricted option behaves like enabled on
7912 |
|
7912 can not initiate hold w/ multiple calls per line and shared
lines. |
|
The browser window on the 7912 opens when it should not |
|
There is no dial tone when exiting from the directory menu |
|
7912 Chinese Locale- Unable to display calling number |
|
CHSWrong Phone display |
|
DTMF when users mash 7912 keys unrecognizable to AA/IVR |
|
7905/7912- Does Not Format '?' Characters in Services URL
Properly |
|
XML Error [4]-Parse Error on 7912G when creating FastDial
in PAB |
|
Found dtmf digits fail when calling into Meeting Place
IVR. |
3.3-Devpack-59.2 |
|
CSV and XML files for Baker Project should be updated to
reflect new fea |
3.3-Devpack-59.1 |
|
Turbo- Error Extracting File using latest tc-sccp.jar file |
3.3-Devpack-59 |
On 7970 Display-on-Time shows
default value after setting it to blank |
7940/7960 (Load - P00307020200): |
802.1x auth state remains after
PC disconnect |
|
Video stream not terminated
when CM is down Bsphere 2628 |
|
Incorrect status msg when no
ctl on phone and modified ctl dwnld |
|
NetworkConfigurationX tag names
do not match Network Config UI |
|
7960/40 does not support QueryStringParam
as documented in SDK |
|
Help for side car buttons throw
an error |
|
IPSvcssupported xml fields size
are 1 less than max |
|
IPsvcNew http headers support
as per SDK 4.0(1) |
|
Lock icon overlaps to page
title text |
|
Mid-call video starts when
active call is in mute state |
|
Idle URLRefresh page does not
recover after a packet loss |
|
Phone shows encrypted call with
CM 3.3 |
|
Phone accepts
invalid/Reserved/Multicast IP address |
|
Security Configuration menu
name should be separate from title |
|
invalid display by ip phone on
key pad uris push |
|
Clear softkey doesnt clear
interface stats on HTTP page |
|
phone not updating volume
changes during call preservation state |
|
Autodial fails on choosing hold
option for the current call |
|
Handle current call not
displayed on dialing from directories |
|
Not able to scroll down to see
help pages displayed by i button |
|
pressing first line speed dial
causes second line to go offhook. |
|
7940/60 phone should use HTTP
1.1 for URL with IP address |
|
Auto line select enabled
prevent use of softkeys on 1st line |
|
No PORT_UP event on 7940 if
PCport on Phone changed frm 10Mbps-100Mb |
|
7960 stuck in booting process
when press service before phone alive |
|
phone sends tftp request to ip
address 0.0.0.0 |
|
7960/7940Voice Quality
Degradation With Echo Back To Remote Party |
|
Phone does not retains Volume
Settings changes |
|
Shared line call doesnt display
toggling between lines correctly |
|
7960/40 phone will not fail
back to primary |
|
Support calloc caller PC broke
LA built. |
|
Change in behavior of resuming
the call that is onhold on IP Phone,7.1.2 |
|
Phone connects to secure SRST
if bad config |
|
Clouseau
debug infrastructure implementation in 7960 sccp phones. |
|
Retain old BA while LA upgrade |
|
speaker button won't work with
sidecar |
|
Disable the display debug
tracing by default on 7960 phones |
|
Update copyright year on
mid-range IP Phone boot display |
|
7940/7960 display HTTP
error[11] when pressing Services/Directory button |
|
After a preserved calls is
terminated, the phone is stuck |
|
Key rollover with Hold and
EndCall Softkeys causes wrong action |
|
7940/60 stuck in Configuring CM
List state |
3.3-Devpack-58.2 |
TurboError Extracting File
using latest tc-sccp.jar file |
3.3-Devpack-58.1 |
Known Caveat w/7940/7960 CSCsa63893 |
Change in behavior of resuming
the call that is onhold on IP Phone,7.1.2 |
7970/7971 |
|
7970 won't boot w/ inline power |
|
7905/7912 |
|
TFTP Client Busy Retry Behavior |
|
7912 doesnt display correct
Softkeys when using MCDN feature |
|
IP Phone 7905 not responding to
http commands |
|
7912 cant ring immediately when
receiving a call after fallback |
|
MWI will be turned off by
incoming call |
|
7905/12 display English prompt
at Services page |
|
7912 ignores
StationClearPriNotifyMessage from CME |
|
Authentication delay between IP
Phone 7905 and CM 5.0 is to long |
|
Issues with processing of DNS
packets |
|
7912 RTP URI push during call
requires user to cycle hook twice to end |
|
7912 dies when configuring
Graphics via TFTP on CCM 4.1 |
|
During cross upgrade, power
off/on the phone & the phone never come up |
|
Found dtmf digits fail when
calling into Meeting Place IVR. |
|
7920 |
|
BSSID is all Zeros in
Reassociation Packets |
|
Site Survey Detail Shows the
Same Info for All APs Sometimes |
|
7920 Does Not Answer IGMP Query |
|
7920 Could Get Into Continuous
Roaming |
|
7920 May Get 1 Way Audio
Without ARP-Caching |
|
7920 Will Sometimes Show RSSI =
1 |
|
Packets are Sent at 1mbps rate
Off Call When 7920 Uses a Non-Auto Rate |
|
7920 Advertises All Rates Are
Supported When Non-Auto Rate Is Configured |
|
Get association timeouts sometimes
with Aruba APs |
|
6608 |
|
Burst of static during ringback
and connect on calls through 6608 |
3.3-Devpack-57.1 |
7961 DevPack does not install
the locale files |
|
Neanderthal-Implement JAVA side
and QED CM interface |
3.3-Devpack-57 |
|
7961 device pack doesnt conatin proper
device name on device default |
|
7970/7971 |
|
Some items of Streaming Statistics from
7970 inconsistant w/ 7960s |
|
Headset status indicator incorrect after
7970 reboot |
|
7970 incorrect LineType for some line
buttons |
|
7970 not auto answer with headset after
restart w/ headset light on |
|
7970 not put active call in focus after
incoming call disconnected |
|
Phone restart with lower line rate of
multicast/broadcast traffic |
|
7970 fails to reregister after temporary
WAN failure |
|
Ringer volume and other parameters are not
configured aftr DSP reset |
|
Sidetone on handset after reset |
|
7970 ICMP hard errors behavior changes |
|
7970 does not pick up the line when
configured share line |
|
Extra ring heard when answering call after
adjusting volume |
|
7970 RTPRx/RTPMRx URI syntax error allowed |
|
Possible deadlock situation in msg queue
software |
|
Phone stuck at Configuring IP after
prolonged CCM disconnect/recon |
|
7970 drops host in DNS queries with
subdomains |
|
Skate Security config menu opt 5 and 6
display wrong softkeys |
|
7970 RTPRx/RTPMRx URI opens invalid port by
default |
|
Phone lockupCSCeg04380 |
|
7970 gethostbyname() does not return
multiple IP addresses |
|
Mute signal heard on network |
|
When resetting the phone (**#**) PC loses
network connectivity |
|
phone freezes during reboot with mqThread
problem |
|
7970 phone failover to SRST takes more than
6 minutes |
|
Last digit not displayed when dialing from
keypad |
|
JavaException using Navigate Keypad when
call on hold |
|
Phone continue to stay with Requesting msg,
cancel key has no effect |
|
Java exception when 7970 configed with
sidecar but none attached |
|
7970 Phone hangs on changing existing speed
dial from phone (CME) |
|
7970 crash when access protected URL 2nd
time |
|
Onhook Dialing will not accept * or # as
first digit |
|
Core dump of Sunvm.cnu when web-access is
disabled & then enabled |
|
Attempt to load diagnostic image file
causes CNU reset |
|
Onhook Dialing is available when the phone
is not registered |
|
7971 Multicast traffic dest to PC dropped
by switch in phone. |
|
RTPTx Stop not being executed |
|
7971 Unplugging and plug the ethernet
cable, looses VLAN id |
|
Incorrect time for |
|
7970 drops keys if pressed too fast |
|
EM logged off profile keeps CFA icon |
|
Update handling of init.conf authentication
settings |
|
SA Dereferencing pointer to freed memory in
Core/CNU/NetSys/udp.c |
|
SA expression must be a modifiable lvalue
in Core/Apps/cmds/ttrace/ |
|
SA Freeing pointer to already freed memory
in Core/Apps/daemons/DHC |
|
Broken autosensing on type-2 cabling
(BU-3494) |
|
Makaha power request numbers are wrong |
|
ListenerManager allows for multiple
listener |
|
Memory leak when press keys in predial |
|
Memory leak on startup in Call History
property |
|
7971 phone not upgrading load, using device
defaults. |
|
Phone reloads from nmap connect scan |
|
Stream.c flood reloads phone |
|
Failover fail on 7971 phone with CM
3.3.4(SR2) |
|
CVTA with 7970 messes up audio caps |
|
Phone stuck at Updating Software |
|
7970 - does not report Dest Unreach on sendto() |
|
Ethernet Disconnected message interferes
with display (BU-3572) |
|
EndCall softkey doesnt work when CM down
and other end had hit Hold |
|
7971 Low power backlight needs to be 14 |
|
7970 - only retries 4 times after leaseT1
expires |
|
7970 hangs at config IP after reset |
|
Unexpected DHCP Renew after Release
operation |
|
Shared System Threads create debugging
problems |
|
Cut through on speaker phone take approx
one sec |
|
Line button becomes useless after try
dialing from call history |
|
Timer object should allow ITimerListeners
to disable timerCancelled |
|
7970 phone does not close the sockets
automatically |
|
Mid-call video starts when active call is
on mute |
|
7970 registering with CM when a active call
is in place |
|
7971 phone reset after hold/resume duration |
|
Phone freeze after the extension mobility
duration test was run |
|
7970 hangs intermittently while attempting
EM login/logout |
|
XML parse error when text object with 4000
chars of text is sent |
|
Multiple restart from CM causes phone to
freeze up |
|
http push may stop working |
|
Console shows CONSOLE TOO SLOW! Skipping 0
log files! |
|
Trace does not include key press
information |
|
7971 Phone ignore vvlan information from
switch port |
|
CVTA does not receive information on calls
active when PC plugged in |
|
Phone stuck after erase operation |
|
7971 does not comply with 802.3af power
specification |
|
Phone can lose VLAN id with broadcast
storms in the network |
|
PC attached to Phone loses network after
multiple phone reload |
|
7971 phone re-boots when SYNC_RCVD state
sttack was run |
|
Enable 802.3x flow control |
|
7970 plays loud comfortable noise when
using G.729 codec |
|
Can not accept calls when call history is
empty and in focus |
|
7970 change between daylight and standard
time 1 hour too early |
|
Ringer stops working if press speaker right
after adjust ring volume |
|
Phone restarts exposes memory leak in the
CallAgent module |
|
Call Info gone but voice path remains after
brief Ethernet disconnec |
|
Phone does not take Service URL w/ no label |
|
7971 w/ PC connected not operate in low
power mode using ieee inline |
|
7970 does not display missed call info
after waking the display |
|
Phone stuck under simClient duration test |
|
7970 not alllow user to set IP Address
Release as No |
|
7970 should display IP address released |
|
7970 missing date on console logs, status
messages & debug display |
|
7970 Autodial postpends to dialed # if
display name contaions #s |
|
UI issue services tab not coming to
foreground in push scenario |
|
7971 continuously resets if dot1x
configured on switch interface |
|
Services Changing volume while RTPRx -
softkey gets stuck at Save |
|
shownet command in cnush gives wrong output |
|
7971 accepts untagged packets while on a
voice VLAN |
|
AbbrDial softkey appears on 7970 phone in
CM3.x |
|
HTTP Push requests has successful response,
but UI does not display XML |
|
7970 does not properly reset causing
sessions hung in LAST_ACK on CCM |
|
7971 PC port does not show what is
configured |
|
CP-7970 Fails to Boot up if 'switchport
voice vlan dot1p' is configured |
|
Bad voice on 7971 phone with 10% broadcast
traffic |
|
Broadcast traffic throttling rate very low
w/ load 69 on 7971 phone |
|
7971 phone only allows 10M (1%) broadcast
traffic send to PC |
|
Phone does not pass thru all multicast
traffic to PC |
|
7971 switch port stops transmitting frames
causing phone to unregister |
|
Network Statistics does not display Port 1
or Port 2 status information |
|
7971 - PPU workaround does not set forced
link speed correctly |
|
7971 - change CDP from a mgmt packet to a
mcast packet in ATU |
|
7971 - enable VLAN 1 and VLAN 0 |
|
Phone crashed with in half an hour ,when
XML boundary objects script was |
|
Phone crashes for 200 calls per device case |
3.3-Devpack-56.1 |
|
6624 |
|
6624 FXS port is unavalable for 2 mins
after disabling and enabling |
|
updation on 6624 does not reflect on port
configuration page. |
|
FAC tone played continuously on using non
default network locale |
|
6608/6624 |
|
Integrate 4.3.25 DSP firmware for 6608 |
|
6608 |
|
Dicktracy - Remove unnecessary DSP and MLPP
related messages. |
|
6608 Dicktracy - Reduce trunk flash timer
from 700ms to 400ms. |
3.3-Devpack-55 |
|
Add QED support for 7911 |
|
7935 |
|
7935 reboots on its own and couldnt reach
tftp server thereafter. |
|
7935/7936 |
|
7935 Autonegotiation does not work |
|
CCME 7936 conference call one way speech
path and 7936 reboots |
|
7935 and 7936 stops ringing when 2 parties
call it simultaneously |
|
7936/7935 does not support JOIN feature of
CCM 4.0 |
|
Ringer stops during incoming call when dial
pressed under corp |
|
7935 is not accepting cass B netmask, if Ip
addr is class C |
|
Inconsistent LCd and web page display |
|
On first call from 7935 gets one-way voice |
|
7935/7936 marking |
|
7935 will not register to ccm |
|
7936 will not register to ccm |
|
MOH is not heard during Transfer |
|
Not able to configure admin vlan via web
interface. |
3.3-Devpack-54.1 |
|
7970/7971 display instance file and IP
Phone Rules xml files wrong |
|
Phone Config lacks precedence by MIC for
7970 phones |
|
7970/7971 display instance file and IP
Phone Rules xml files wrong |
|
7940/60 |
|
Remove vender specific parameter edit
softkey from IP Phones |
|
Build phone loads |
|
Edit Dial push uris show Directories icon |
|
Unable to answer the call with linekey with
shared lines |
|
14th digit disapears from IP Ph CFA Display
after device reset |
|
Active call moves to the top of list after
9 seconds |
|
7960 Directories button sometimes opens
Services URL |
|
7960 not showing correct display when same
DN config on multiple lin |
|
Phones To Be More Ambitious Towards
Updating Firmware |
|
Phone web page not accessible after socket
stress was run |
|
Cannot load diag image to 7940/7960 phone |
|
Cannot use # or * as first entry while
onhook |
|
7960 should not automatically return to
detail view from overview |
|
With multiple held calls, line key should
not resume oldest call |
|
With single on-hold call, line button
should invoke overview display |
|
Help for side car buttons throw an error |
|
CallManager TFTP Load=6.0(5)0 File Not
Found when phone is reset |
|
Phone stuck in Configuring IP when Factory
Reset, save settings dhcp |
|
LA loader must check new LA size before
burning to flash |
|
7960 crashes during XML POST with
IPPhoneExecute |
|
Garbage help text at a certain key sequence |
|
An error at a certain key sequence |
|
Selecting directory entry with keypad
doesnt update display |
|
7960 stops call timer when the CCM down |
|
Key rollover broken/missing digits when
dialling |
|
Wrong association of 7940/60 help |
|
http// <phone> web page needs links
to all streams info during barge |
|
unable to answer 2nd line when speaker
phone is disabled. |
|
7960 will not stay registered if
ringlist.xml has invalid syntax |
|
Time display not updated on certain phone
menus |
|
Changing Phone port # causes 7960s in Auth
mode not to register |
|
C3PO Frame Buffer overflow causes COS3
packet drop |
|
IPSvcs - In case of missing refresh URL,
dont show update softkey |
|
Extend scope of Msg/Dir URL to support icon
menu |
|
IP Phones fails to recieve Audio Multicast
Stream and gets reset |
|
Phone unable to get Ringlist.xml using
Alternate TFTP |
|
Audio cut through delay during Call Waiting
Answer |
|
RTP URI push during call requires user to
cycle hook twice to end |
|
Cisco 7940/7960 One-way audio and Freeze or
Reset |
|
7940/60 DHCP Option 60 data different
between big and little app |
|
URI SoftKey Dial resets the phone |
3.3-Devpack-53 |
|
7902/05/12 |
|
7912 unable to be registered when User
Locale is Japanese |
|
CP-7912G/7905G does not add 802.1p tag when
no vlan is configured. |
|
7905 and 7912 phones reboot with
keep-conference feature |
|
OPickUp softkey does not work on 7912/7905 |
|
Multiple Calls on Dir Num calls were
disconnected by CMs failover |
|
7905 phone web server sends data in wrong
HTTP version |
|
Select softkey in phrase 609 and 178 should
be defined properly |
|
7912 and 7905 may crash and fail on
re-registering |
|
Phone does not accept DHCP ACK sent to the
broadcast address |
3.3-Devpack-52
|
|
Due to |
The 7940/60 default loads are not being set
|
3.3-Devpack-51.1
|
|
3.3 devpack 51 installation failed 7971G-GE
to auto register. |
3.3-Devpack-51
|
|
7971 phone icon missing from CM Admin page |
|
7971 device type and load need to be added
to CM releases |
|
6608 |
|
6608 Support for T1 CAS Guard time |
|
6608 Fax Relay debugs in D00404 firmware
need to be same as D00403 |
|
6608 inbound call mistaken for hookflash |
3.3-Devpack-50.2
|
|
7970/7971 display instance file and IP
Phone Rules xml files wrong |
3.3-Devpack-50.1
|
|
Wrong WS-X6608 DSP load included with
device load in 4.0(2a)SR1 |
3.3-Devpack-50
|
|
7935/7936 |
|
7935 upgrade process unnecessarily
complicated |
|
Add remove last participant feature |
|
7935 requests unicast DHCPOFFER, but does
not process it |
|
7935 ip phone failed to re-home to SRST
gateway |
|
7936 Phone fail to get IP when native vlan
id is same as voice vlan |
|
7935 Will Not Boot |
|
7935 unmutes if there is call on shared
line |
|
7935/7936 line number display blink with 24
digit length. |
|
7935/7936Phone display is freezed with 24
digit line number |
|
special keys(*,#) under Corp Dir search
7935 behaves unexpectedly |
|
7936 goes off mute, when shared line is put
on hold and resumed |
|
Phone fails to ring when 7936 LCD displays
previous call statistics |
|
7936 hangs during hold session |
|
Vendor String Inconsistant for 7935/7936 |
|
SRST not getting displayed anywhere in 7936
system menu |
|
7936 Fail to download config file with
secured SRST configured |
|
No cdp entries for 7935 when cat-6K is
configured for cdp V1. |
|
HTTP port info lost during f/w
upgrade/dowbgrade for 7935/7936 |
|
Not able to configure admin vlan via web
interface. |
|
SRST registration info not shown on Systsem
information on 7935 |
|
Help page for Network setup on 7935 has
error. |
|
show cdp neigh details does not contain the
IP address for 7935 |
|
Error message not shown when junk chars
tried for ping on 7935s web |
|
7935 in default display reboots instead of
restart when **#** appld |
|
7935s web interface accepts wrong IP and
subnet formats. |
|
no caller id info shown when 7935 called
via FXO/T1/E1. |
|
**1,**5,**7 are not able to set as admin
passwords on 7935 |
|
No caller id info shown when 7935 is not in
its default display |
|
Web interface for 7935/7936 shows wrong
date format for YY/MM/DD. |
|
Not able to mute the first call when theres
an second incoming call |
|
7905/7912 |
|
Switching back and forth between 2 calls
makes the display disappear |
|
Unable to switch between two active calls
on 7912 |
|
ephone-template on 7912 removes message
softkey |
|
7912 and 7905 may crash and fail on
re-registering |
|
7914 |
|
7960 does not show call information when
shared line is active |
3.3-Devpack-49
|
|
6608 inbound call mistaken for hookflash |
|
7940/60 |
|
CallInfo CLI output not correct for
different locale file |
|
7960 shared line predialled digits keep
ringing, call ansd on 7970 |
|
Ip Phone doesnt accept option 66 with
trailing dot in hostname |
|
Devices attached to phone lose network when
PC VLAN enabled |
|
7960 does not display CallInfo if CCM down
while in the call |
|
Unable to access protected URL from menu
using custom softkey |
|
IP Phone recognize dialed number in wrong
order |
|
Display shows only first 23 digits of a 24
digit DN |
|
Dial keys do not respond for 10 secs after
pressing **# |
|
The link http// displays wrong DN |
|
Phone doesnt display the DN to be edited
when editdial is pressed |
|
Loader may fail - Application Invalid |
|
Phone should not cache failed credentials |
|
Phone may stop communicate with CCM or CAPF
when using TLS |
|
7960 registered to CM 3.3 shows only one
line while call on hold |
|
Edit Dial on cancel shows Host Not Found |
|
AD Phone search always has word dial
appended |
|
Extra ring heard when answering call after
adjusting volume |
|
Called Party name is wrong when call is
forwarded over ICT |
|
AutoDial Fails in a Active Call beetween IP
Phone and MGCP Endpoint |
|
I-Button doesnt give any Help for Ring Type
Select/Default/Exit |
|
7960 struck with Booting Dsp alarm on its
display |
|
Echo fades in and out when talking IP phone
to IP phone |
|
7940/7960 IP phones showing as untrusted on
Cat3550,3560&4500 |
|
Phone fails to come up when wrong load Id
is mentioned on phone page |
|
Failback during cert gen not behaving
properly |
3.3-Devpack-48
|
|
Default English Locales files missing for
7970 |
|
7970 |
|
Incorrect time for |
|
7970 not put active call in focus after
incoming call disconnected |
|
7970 drops keys if pressed too fast |
3.3-Devpack-47
|
|
Remove the extra are-you-sure from the
ES/SR installs |
|
Uninstall Confirmation dialog should
mention version reverting to |
|
7920 |
|
Re register to CM after pressing 3 times on
the disconnection button |
|
7920 has static noise when using Alaw. |
|
7920 Will Not Ring after using the 7920
Config Utility |
|
no network after overnight connection |
|
Phone Reboots in Stressed Scenarios |
|
7920In Use Remotely text inconsistent |
|
(Vivien)Need to press power button several
times for boot the phone. |
|
7920 Only Reports Initialized for Last=
Reset Code |
|
7920 does not reply to arp request |
|
7920 shutdown automatically |
|
Short Preamble not used. |
|
ACK frames are sent late |
|
Listen Interval is incorrectly set to zero |
|
7920 sometimes gets stuck on Connecting to
CallManager |
|
7920 scantask lockup causes watchdog to
trigger a reboot |
|
7920 uses weak LEAP challenges |
|
7920s Transmitted Audio May Be Choppy |
|
May Get LEAP Password Prompt With EAP
Reauthentication Enabled on AP |
|
LEAP failure due to 7920 entering wrong
state |
|
7920 phone failed to register with
CallManager |
|
7920 Does Not Cache IP Settings Info |
|
roaming not triggered by missing beacons |
|
when being deauthenticated, 7920 keeps
coming back for same AP |
|
7920 malfunction caused by TCP socket
broken |
|
Choppiness in Tx Path 1 - Jitter in Tx
Packets |
|
Choppiness in Tx Path 2 - Packets are not
sent to ARM2 |
|
7920 Does Not Have Auto Transmit Power
Capabilities |
|
Choppiness in Tx Path 3 - Multicast Traffic
Affects Audio Path |
|
Your Current Options shows up during
Hold/Resume toggle |
|
7920 fails to reregister to CCM, MMI shows
Authentication OK |
|
Audio gaps of 1-3 secs when 7920 roams in
cells w/o ideal RF overlap |
|
Handoffs should be triggered by Rx and Tx
failures |
|
High multicast traffic causes reboot of
7920 consistently |
|
Vendor String Inconsistant - 7920 |
|
Heavy Broadcast ARP traffic causes reboot
of in-call 7920 |
|
7920 unexpectedly rebooted during a call |
|
7920 may send loud screech or feedback loop
in outbound RTP stream. |
|
8 phones rebooted at the same time in test
-- memory problem poss. |
|
7920 softkey title display strange
character |
|
Wrong status codes sent to ARM1 in
authentications and associations |
|
7920 Needs to Provide Device ID Info to AP |
|
Phone does not acknowledge packets after
waking up in idle mode |
|
Get No Network Sometimes Due to LEAP Issue |
|
No audio btw two 7920 phones (Bsphere 2744)
|
|
Sometimes phone sends PS-NULL after
starting scan on another channel |
|
7920 uses 1M rate for all traffic except
RTP |
|
The voice distortion can be heared by human
ear. |
|
Hang up the call on 7920, the ring back
tone still be played |
|
The busy tone and alert speech will be
played at the same time |
|
Phone will stay at TFTP no response state |
|
(Vivien) MMI is out of disorder after press
the end softkey |
|
MMI disorder after share line call incoming
|
|
7970 |
|
7970 incorrect behavior when try to dial
from dir with call on line |
|
7970Override Auto Answer if Speaker Disable
False doesnt work |
|
7970 Phone stops accepting HTTP connections
|
|
MUTECall Stat still shows Sender Packets
incrementing mute is on |
|
7970dynamic call forward icon not updated
properly after login |
|
Double selection of same ringer deselect
it, also display problems |
|
7970Problems with ringer selections |
|
Ringing could not be stopped when call
disconnected from far end |
|
Jitter Tolerancenew field added are not
saved in conf file |
|
Receiving default config file does default
previous cfg parameters |
|
7970 Does not translate Australian Daylight
Savings correctly |
|
TFTP Server address gone after Enabling
DHCP w/Alternate |
|
7970 lists Load File as term70.default.
User doesnt know load name. |
|
No way to view call data on another line
without answering call |
|
7970 Web page doesnt display network
statistic info correctly |
|
Touching screen to wake up screen saver
often invokes a soft key |
|
Phone Resets swtiching from
Services->Settings after loading images |
|
Erase in Security Configuration menu only
erases one item |
|
Redirected Authentication URL does not work
|
|
Lifting handset in EditDial calls unedited
number |
|
7970 doesnot failback from SRST when trying
to make call |
|
Cannot open, close, reopen PC/SW Port
Config |
|
7970 boot hangs with unrecognized timezone
name |
|
7970 does not obey
StationSetMicroModeMessage (mute microphone) |
|
CP-7970 does not populate CallingPartyName
in Missed Calls Field |
|
CP-7970 Time get out of sync if not used
for extended period |
|
DEvice Config submenus donot have
lock/unlock icon |
|
No alarms or phone logs when 2 of 4 locale
files not found |
|
With 6 calls, resuming first causes 5th
duration overwritten by 6th |
|
Pressing NewCall, EndCall with 7 calls on
hold leaves no call hilite |
|
call timer for barged call incorrect |
|
Add help for Call Agent Menu 1161 |
|
Add help for HTTP Menu 1162 |
|
Add help for Locale Menu 1163 |
|
Add help for Power Save Menu (1164) |
|
Add help for Ethernet Menu (1165) |
|
Add
help for Media Menu (1166) |
|
Add help for QoS Menu (1167) |
|
Add help for UI Menu (1168) |
|
Add help for Span PC Port (1169) |
|
Update path to admin tasks in online help |
|
DHCP gets hung on boot |
|
DHCP disable and CTL Erase enables DHCP |
|
GARP and VVLAN enable and disable reversed
on display |
|
CTLFile stays unlocked still after re-dhcp |
|
7970 not able to save downloaded background
image |
|
file auth error after factory reset |
|
Barge functionality not working for shared
line between 7960 & 7970 |
|
7970 displays Mid-Atlantic time zone
incorrect |
|
Default string is used as both softkey and
parameter value |
|
HTTP request do not work on 7970, different
from 7960/40 |
|
7970 stops sending CDP to attached Cisco VT
Advantage PC |
|
7970 does not notice media disconnect when
CVTA PC unplugs |
|
7970 Wont Register after upgrade to 3.3.4 |
|
7970 displays incorrect softkey sets when a
call barged in |
|
RUS Line text label shows garbage on 7970
IP Phone |
|
Extension Mobility in 7970 shows English in
all locales |
|
7970 hangs on request of LineInfo |
|
Erase softkey missing on Network Config
menu |
|
7970 does not properly interpret parameter
E |
|
7970 running 6.0.1 load does not show
remote in use on shared line |
|
XML services returned NullPointerException |
|
7970 continues to ring after call is
disconnected |
|
PC behind the phone cannot authenticate
into the network with 802.1x |
|
7970 displays NZ ( |
|
7970 CiscoIPPhoneInput Softkey gone if
there is expire header in asp |
|
XML post to 7970 using @ in password resets
phone |
|
7970 phones query DNS instead of using
proxy address for services |
|
7970 phones query DNS instead of using
proxy address for services |
|
7970 voice quality degrade with UDP
broadcast traffic. |
|
7970 shared line with out Barge causes
phone to display incorrectly |
|
One second refreshing of
CiscoIPPhoneImageFile objects fails |
|
When in refresh XSI loop, hitting cancel
does not cancel the request |
|
7970 does not display Registration Rejected
messages |
|
Softkeys disappear after cancle of callback
on a held call |
|
7970 sends a 5-msec packet before a type13
packet (Hurt Confer. Brdg |
|
7970 unregisters after unplugging PC from
PC port |
|
7970 Has no serviceability to retain stack
traces after initialize |
|
7960 Call Info display behavior
inconsistant |
|
TCP SYN vulnerability and Cisco phone end
points |
|
Execute URL on 7970 is doing a DNS lookup |
|
7970 does not queue URLs from
CiscoIPPhoneExecute |
|
Disable speaker does not work |
|
Pressing line button for active call doesnt
go to overview screen |
|
7970 causes continuous popping noise in a
MCU conference (VAD=1) |
|
7970 display / softkeys will freeze with
high incoming call traffic |
|
7970 display / softkeys will freeze with
high incoming call traffic |
|
7970Select key is not greyed out on Ring
menu |
|
7970 still display IPMA manager watch
window after switch CCM |
|
7970 resets on pressing **#** while on
corporate directory screen |
|
Http request http//phones IP/CGI/LineInfo resets
the phone |
|
7970 failed to recover from DSP error - DSP
stopped by assertion |
|
7970 added code to dump DSP message when
its reponse faied to return |
|
7970 will not allow a CVTA CAST connection |
|
Config file hunt on all tftp servers |
|
7970 stops accept HTTP after incorrect PUSH
message |
|
7970 advertises wrong platform - CP-7 |
|
HTTP headers are case sensitive |
|
7970 not answering calls while in a menu |
|
7970 resets when accessing Network Statistics
via web interface |
|
Date Time Group=Local time zone wrong in
7970 |
|
7970If QRT key is pressed during active
call softkeys disappear |
|
Vendor String Inconsistant - 7970 |
|
Parche phone cannot upgrade when config
file has secure SRST |
|
GARP is enabled in CM but showing GARP
Enabled Yes on the phone |
|
Exit key not work when Dial from Directory
on active line |
|
Skate7970 not accepting untagged packets |
|
Incoming call droped if Dial from
Directories |
|
7970 shows wrong softkey sets w/ Callback
and incoming call |
|
7970 does not close CallBack application
after dial from CallBack |
|
7970 DHCP timer changed to 10 seconds |
|
7970 Phone ServicesURL handling disparity
between 7970 and 7960 |
|
7970 UI freeze up under stress test |
|
Accessing web page in 7970 causes crash - possibly
auth. problem |
|
CP-7970 has worng values on XML config |
|
Pressing Services button causes phone to
fail |
|
Phones stuck in Configuring IP after reset |
|
Soft resets freeze phone - memory leak |
|
Soft resetting causes flash memory error |
|
7970 should not make new call pressing line
button w/ callback |
|
7970 shows CCM Down after restart from CCM
w/ Active call |
|
Unable to answer call with help menu active
unless Answer is pressed |
|
Phone processing SIGIPCFG before phone app
loaded |
|
7970 display error on Brightness menu after
answer call |
|
7970 not auto answer with headset after
restart w/ headset light on |
|
7970 display error in Hold/Resume stress
test |
|
7970 doesnt respond to Reset when shared
line has Remote-In-Use call |
|
Predial does not work when using offhook,
line key, or speaker |
|
7970 crash w/ calls on 3 lines |
|
Skate SCCP messages cause phone to crash |
|
CNU doesnt reboot after 4 consecutive
resets |
|
7970 does not take changes to DSCP for SCCP
phone config field |
|
7970 phones unregister with Missing
keepalives |
|
7970 lost registration to CCM during
Hold/Resume duration test |
|
7970 timer thread cause 100% CPU usage leading
to reset |
|
7970 displays blank/empty pages when
receiving IPPhoneStatus request |
|
Incorrect time for the Australian time zone
AEST |
|
Java.lang.NullPoinerException while 7970
fail over |
|
7970G will not upgrade to newer load unless
power-cycle |
|
Memory Leak on Restarts when there have
been calls |
|
Null Pointer Exceptions when calls ended
that are not visible |
|
Init AppStatus URI does not work and causes
an exception |
|
7970 hangs randomly, requires reset. |
|
7970 stuck in unregistered state if network
down w/ 150 held calls |
|
Screen on 7970 phone got overwritten by page
that has refresh timer |
|
7970 locks up on boot up with failed assert
(pos <= t->maxPos) |
|
7970G - Pushing xml obj with long tags
resulted in Phone reboot. |
|
7970 becomes inoperable after firmware
upgrade attempt |
|
7970 phone got resetted when user hit
setting key |
|
7970Sending http request to the phone
freezes it |
|
CP-7970G - SELECT function works on
touchscreen / not softkey |
|
7970 fails to reregister after temporary
WAN failure |
|
Input of softkeys/linekeys/navkeys not shed
if too high of rate |
|
CDP exits during link flap test |
|
CNU doesnt restart the VM when it exits |
|
7970 DSP reset due to libMTdoorCall select
timeout |
|
Calls up when CCM connection is lost are
not avail for reuse |
|
7970 can not boot after upgrade/downgrade stress
test |
|
JVM not shut down properly when OS reboots
due to rapid resets |
|
Need to increase size of syslog files to
provide more debug data |
|
Exceptions in the ITimerListener Dispatcher
starves ObjectPool |
|
There is no way to determine the DHCP/CDP
state from the GUI |
|
7970 hang after idle a while |
|
Memory Leak when Entering Menus |
|
nformation message displayed continuously
on console |
|
7970 crash after Erase config several times
|
|
DSP process signal traps (killed)->
doorCall select timeout |
|
When java.lang.OutOfMemoryError, init
doesnt restart VM |
|
Can only answer call via Answer softkey
after handle call failure |
|
7970 has resize error during stress test |
|
7970 phone freezes when the XML objects are
pushed |
|
7970 displays HI ( |
|
No packet sent when Silence suppression is
turned on |
|
7970 displays empty callback page with no
softkey |
|
In some Interfaces there is a potential for
ObjectPool leaks |
|
# key displays error insted of its
character set i.e. # + $ et al. |
|
Message button becomes inactive after
config message URL |
|
7970 - CDP can not acquire VLAN info |
|
RMS FULL Exception has no handler |
|
7970 sending wrong security capabilities to
SRST |
|
7970 Hearing white noise when using codec
g729 |
|
7970 Hangs on reset from CCM |
|
Phone freezes when a XML object is pushed
and exit is pressed for 6 |
|
Phone in requesting loop when XML objects
are pushed sixth time |
|
7970 cannot parse non-URL proxy server
address |
|
7970 doesnt mark services and HTTP packets
correctly |
|
7970 stuck in Configuring IP when erase CTL
with DHCP disabled |
|
7970 - DNS does not return from select
errors |
|
Phone freezes during upgrading test with
REL signed image |
|
7970 stops at Configuring IP after its
config erased |
|
XsiDirectory Response causes memory leak |
|
7970 has Segmentation fault with its CCM
switchport flap |
|
Wrong Security Icons shown for 7970 Phones
in SRST mode. |
|
CiscoIPPhoneStatus object leaks graphic
resources |
|
Hashtable.get() is returning an invalid
Exception |
|
Phone continue to stay with Requesting msg,
cancel key has no effect |
|
No Audio & call is dropped for a G729
7970 call after CM Restart |
|
Default keys shown while using custom keys |
|
ServicesPrompt line not cleared if new page
has no prompt |
|
Multiple timezones are incorrect |
3.3-Devpack-46
|
|
Version Conflict with Device Package during
SR1 install |
|
An error message popsup on installing
SR01-rc2.1 |
|
Programs Menu still points to
ciscoupdate.txt and not new Logs |
|
Misleading CCm Ver Msg if Patch installed
on a Non-CCM Server |
|
SR Patch Ver check lists From as old SR and
not new MR and misleads |
|
Patch installs should write Log File with
unique time-stamps |
|
Telling customers From->To will prevent
acccidental valid upgrades |
|
Msg if we wish not to view log should be
consistent for install/unin |
|
6608 T1/E1 |
|
Negative value for 6608 counter Total Rx
RTP Lost Pkts |
|
6608T1 CAS HookFlash is detected in |
|
6608T1 CAS Glare Recovery may not work
correctly |
|
configurable
non-linear comfort noise attenuation for 6608 |
|
6608 does not send RSIP forced to CCM when
a reset comes from CCM |
|
6608T1 CAS Disconnect
Procedure Enhancements |
|
6608 T1 cas gateway fails to clear line for
unallocated numbers |
|
7902 |
|
Hold lamp of CP-7902G is not turned on during
Transfer in SRST mode. |
|
7902/05/12 |
|
Setting/Web access cannot be changed in
different network |
|
7905/12 |
|
HUN - KATE file for 7905 does not display
required chars |
|
HUNtime on the phone display is not showing
in Hungarian |
|
Can not pick up the latter reached call on
7912s shared line. |
|
7912 will not fallback from SRST to CCM
when the CCM is back online |
|
7912 Delayed Dial tone, Retransmit time |
|
7912/7905 do not implement the RTPMRx URI
correctly |
|
Wrong CallInfo Display in CME environment |
|
7912G Japanese locale not working for
Extension Mobility login/out |
|
add OPickup for CCM 4.1(2) |
|
Display English Acct softkey in |
|
Missing dialed number after pressing
service button |
|
7905 XMLEncode URL which is already encoded
in some cases |
|
CP-7912G support controlling DSCP marking
for voice bearer. |
|
7905/7912 should save setting/web access
config |
|
CP-7912G does not control layer2 CoS value
for skinny and RTP packet |
|
Ext Mobility does not work for some dev
profiles on 7912 & 7905 |
3.3-Devpack-45.1
|
|
configurable
non-linear comfort noise attenuation for 6608 |
3.3-Devpack-45
|
|
6608 |
|
6608- T1 CAS HookFlash is detected in |
|
6608- T1 CAS Glare Recovery may not work
correctly |
|
configurable
non-linear comfort noise attenuation for 6608 |
3.3-Devpack-44
|
|
Add/Remove Programs can NOT be closed after
SR Install Fail/Canceled |
|
SR Install by a non-Admin valid NT user
gives a weird Line 1613 Err |
|
6608
D00404000012 |
|
T1CAS channel becomes unusable after an
invalid number is called |
|
6608 T1 CAS should not clear call until
hookflash is complete |
|
T1 CAS 6608 channel gets stuck in
CSMaintOOSFE state |
|
6608 Marks CCM as BADCCM and would not
recover |
|
6608- T1 CAS Glare Recovery Enhancements |
|
Call drops reported on 6608 |
|
6608- T1 CAS channel is stuck in
CSCallAbandon, DISCONNECT_REQ state |
|
6608 sends T1 CAS IDLE signal before
clearing the IP leg |
|
6608
D00404000013 (Default) |
|
DSP firmware 4.3.222 for 6608 |
3.3-Devpack-43
|
|
ATA18x |
|
|
|
ATA connected to WAN can get into hang
state |
|
ATA behaves differently in Conference Call under
CCM 3.3 and 4.0 |
|
ATA behaves differently in Call Hold/Resume
to CCM 3.3 and 4.0 |
|
ATA186 is not playing MoH on load
ATA030100SCCP040211A |
|
Support for Multicast Music on Hold for
SCCP |
|
ATA186 stops sending RTP packets for
presevation call in 5 minutes. |
|
ATA call on port 2 only not preserved
during CCM failover |
|
ATA186 can not do IP Reassembly correctly |
|
ATA may experience one-way audio |
3.3-Devpack-42.2
|
|
Version checking improvements needed for
Standalone DevPack install |
3.3-Devpack-42.1
|
|
SR2 for CM 4.0(1) error regarding
C\Ciscowebs BAT _RemoteScripts |
|
install didnt exit after critical error
during preupgrade db check |
|
SR Install fails with misleading msg if Log
Dir not accessible |
|
Patch logfile takes too long to load at end
of installation |
|
Service Pack Installs should be blocked is
Terminal Services |
|
Print ** No errors detected** when no
bonafide Patch Install errors |
|
Need UI Confirm check needed for dev
defaults in standalone devpacks |
|
3.3 Device Packs require tftp reset for new
Dev Default to work |
|
Version checking improvements needed for
Standalone DevPack install |
3.3-Devpack-42
|
|
Lennon load D00404000009 not available on
installing 3.3(4)SR02-rc2 |
|
The following resolutions are resolved
if manually upgrading the 6608 load to D00404000011. The current recommended
load is still D00404000009. |
|
6608 |
|
6608 Expands Playout of In-Band DTMF Tone
to > 40msecs |
|
Complete CAS trunk not registering on 6608 |
|
WS-x6608 Gateway with active calls,
switches back to primary CM |
|
Dicktracy MGCP traces cause gateway memory
corruption |
|
6608 T1 CAS State Machine problems when
call dropped during transfer |
|
6608 stops accepting calls after exeeding
31 active call references |
|
6608 T1 CAS should not clear call until
hookflash is complete |
|
Partial
fix for |
|
Call drops reported on 6608 |
3.3-Devpack-41.1 |
|
|
The following resolutions were removed due to
issues with the 6608 load in Devpack 40 |
6608 Expands Playout of In-Band DTMF Tone
to > 40msecs |
|
Complete CAS trunk not registering on 6608 |
|
WS-x6608 Gateway with active calls,
switches back to primary CM |
|
Dicktracy MGCP traces cause gateway memory
corruption |
|
6608 T1 CAS State Machine problems when
call dropped during transfer |
|
6608 stops accepting calls after exeeding
31 active call references |
|
6608 T1 CAS should not clear call until
hookflash is complete |
3.3-Devpack-41 |
|
7902 Phone sends additional digits |
|
Consultant transfer does not work when 7902
is transferor on SRST |
|
Low end phones ignore ICMP redirects |
|
7912 phones report CM-aborted-TCP when
restarted from CCM Admin |
|
7912 loops in ARP when duplicate IP and
using DHCP |
|
Power off/on of a 7912G cause oneway voice |
|
7912G cannot hear MoH when previous call
exsist |
|
7912/7905/7902 can not do IP Reassembly
correctly |
|
7905/12 wrong behavior during failover |
|
CPTONE GB incorrect tone and cadence for
7905/12 |
|
7912G softkeys missing after registers to
SRST router |
|
7912 No call history in Placed Calls at the
called party |
|
Answered calls shown in missed call history
in 7912G in SRST mode |
|
7912 sends wrong Accept-Language header in
HTTP request |
|
7905/7912G http does not match RFC
compliance |
|
7912 is not registered with correct locale |
|
Documentation 7905G/7912G Changing Logo IP
Phone LCD Screen incorrct |
|
Display wrong directory search results |
|
Monitor softkey disappears on 7912 phone |
|
Softkey menu become invisible on 7912G with
Japanese locale. |
|
Bottom of Japanese letters are not
displayed on 7912G LCD |
|
7912G resets when two ExecuteItem+Priority
messages are sent |
|
Up/Down doesnt show Speed Dial when
7905/7912 are Offhook |
|
7912 shows XML parse error when HTTP pckts
are returned out of order |
|
7905 XML URI handling differences between
7960 and 7905 |
|
7905/7912G does not queue URLs from
CiscoIPPhoneExecute |
|
Removing the Message softkey from 7905/7912 |
|
some parche features were broken on 7905/12
with CCM 4.1(x) |
3.3-Devpack-40 |
|
Complete CAS trunk not registering on 6608 |
|
6608 Expands Playout of In-Band DTMF Tone
to > 40msecs |
|
WS-x6608 Gateway with active calls,
switches back to primary CM |
|
Dicktracy MGCP traces cause gateway memory
corruption |
|
6608 T1 CAS State Machine problems when
call dropped during transfer |
|
6608 stops accepting calls after exeeding
31 active call references |
|
6608 T1 CAS should not clear call until
hookflash is complete |
3.3-Devpack-39.1 |
|
I-button help for GPickUp softkey is
misspelled |
|
Remove Model Information from menu for
Communicator |
|
Need to add a Communicator-specific topic
about directories |
3.3-Devpack-39 |
|
Cannot change SW port network config on
7910 |
|
Phone crashes after bugtrap 0x18 |
|
ECT CTI/SCCP traffic causing phone to
reboot/freeze during call xfer |
|
9th incoming calls not answered via IP
phone |
|
IP Phone boots when an assigned URL is
invoked using a message buttn |
|
Default Ring Type softkey is unusable
during ring type selection. |
|
Cisco IP Phone does not send a DHCP Release
message |
|
UPDATE softkey on HTTP pushed object
results in unexpected behavior |
|
CVL- 7960 reboots when PC ethernet port is
unplugged and plugged in |
|
HTTP error thrown when accessing Service
through ServiceURL |
|
Ring-back tone stops on 1st line if a new
call comes on 2nd line |
|
Phone doesnt attempt to use secondary DNS |
|
Ringer not stop after a call gpickuped to
another phone |
|
7960 ignores packets from some source
addresses |
|
Phone Socket Task stack size alarming high |
|
SRST- calls dont go through when onhook
dialing with Speaker button |
|
Phone may reset while rendering
CiscoIPPhoneImage |
|
7960 struck with Booting Dsp alarm on its
display |
|
Phone does not handle RST after SYN,ACK
from backup CM server |
|
Downgrading 7960/40 from 6.0(2) causes tone
corruption |
|
Idle URL on 7940/60 phones will override X
New Missed Call message |
|
7960 sometimes doesnt transfer big files in
http query correctly |
|
Chirp2 ring tone does not work on 7910+SW
IP phones |
|
7960 Phone TCP stack does not recover from
gap in transmit window |
|
IP Phone rejects XML push |
|
IPPhonSvc - Directory plane does not
filters !xml_menu_object compl |
|
Phone reset on phoneSetDisplay request via
TAPI app. |
|
Echo fades in and out when talking IP phone
to IP phone |
|
IP Phone does not play 4th column DTMF tones
when using handset |
|
speaker phone volume too low on CCM 3.3
phone loads |
|
IP Phone is resetting if Switch has no CDP
enabled |
|
Search under corporate directory using
wildcharacters fails |
|
Providing a softkey to another input page from
a input page fails |
|
Softkeys stays inactive even after enabling
Speakerphone and Headset |
3.3-Devpack-38 |
|
Unable to call FAC enabled routepattern
from 6624 after calling once |
3.3-Devpack-37.1 |
|
Missing 7936 phone icon in CCMAdmin |
3.3-Devpack-36 |
|
One way audio when calling old IP phone
12SP+ & 30VIP |
|
Universal App Loader does not config file
hunt on all TFTP errors |
3.3-Devpack-35.2 |
|
Sync'd
installation with 3.3(4)ES. |
|
6608 image size reaching the max limit |
|
6608 gateway sends 0 as RTP port number |
|
Audio Bleedover/Crosstalk on 6608 |
|
6608/6624 Traces Enhancements |
|
Org. T1 CAS Cat6k channel gets locked when the
other does not pickup |
|
Handle IS |
|
Calls involving T1CAS with Delaydial fails
in a scenario |
3.3-Devpack-34.2
Added
Support for 3.3(4)
3.3-Devpack-34.1 |
|
need more product specific configuration
via CCM |
|
ATA loops in ARPs when duplicate IP and
using DHCP |
|
7912 phones report CM-aborted-TCP when
restarted from CCM Admin |
|
Call back notification error with 7905/7912
-dial and transfer |
|
7912G softkeys missing after registers to
SRST router |
|
7912-No call history in Placed Calls at the
called party |
|
Answered calls shown in missed call history
in 7912G in SRST mode |
|
7905- Call waiting tone not stopped after
second user aborts call |
|
7905 sends EndCall instead of OnHook at
handset hang-up |
|
7912 7905 registers with default router
with SRST disabled in config |
|
7912 - Locale is changed and cannot be
restored by resetting IPPhone |
|
7905/7912 showing softekey during
failover/fallback process |
|
7912- Call waiting tone not stopped after call
is gone |
|
7902/7905/7912 do not handle RTP header
extension |
|
Video phone codec mismatch and failed the
call |
|
7905/12 phone does not show ITS specific
softkeys |
|
7912 doesnt send proper qos stats to CAR at
call completion |
|
7912 loops in ARP when duplicate IP and
using DHCP |
|
Power off/on of a 7912G cause oneway voice |
|
7920-Cannot do PickUp or GPickUp on ringing
phone |
|
7920 - some ringtones are not downloadable |
|
Loud Laser is not played properly in some
cases |
|
Display gets blank but phone is functional
(partially) |
|
Call PickUp failed on 7920 |
|
One-way audio happened at 7920 when it
calls 7960 locally |
|
7920 shared line with 7960 does not receive
a call |
|
7920 that moves out of coverage area cannot
recover automatically |
|
7920 sometimes gets deauthenticated from
Access Point |
3.3-Devpack-33 |
|
Spurious DTMF is heard from the far-end of
ATA |
|
ATA cannot handle zero length TCP message |
|
Microphone sensitivity for 7940/7960 |
|
Build phone loads |
|
Far end user hear DTMF key release noise |
|
Audible pop heard when using Answer softkey
or line button to answer |
|
796x phone have audio loss and repeated
words during CCC conf call |
|
IP phone resets when Missed Call list
displayed and key selected |
|
Parche- Fix IDs for Help Items |
|
Phone status does not show load authentication
failure |
|
IP Phone displays previous DTMF digits if
goes offhook with handset |
|
implement CIA-92 on 7960/40 |
|
Implement auto-increment of sub version
numbers for SCCP builds |
|
domain name parsing from URL is wrong |
|
P00305000300- Refresh HTTP header with Idle
URL does not work |
|
7960/40 Handset SLR and RLR changed |
|
IP Phone stop accepting XML push after ~100
push |
|
7960 resets if Dial softkey is pressed with
blank results |
|
Xenical- Change in Factory and Ersase
Softkeys |
|
ARP- Internal Repairs for CRT Enter/Exit |
|
Phone shall only use DialedDigits msf to
update placedCalls dir |
|
Remove -o3 optimization from main.o |
|
Xenical- No alarm sent when TFTP not
authorized |
|
Reusing phrase Down causes conflict in
localization |
|
Xenical- CAPFs cancel certificate response
status may be confusing |
|
Phone does not handle DNS names that begin
with numbers properly |
|
AVVID- Phone TCP backoff algorithm slow to
return to initial timeout |
|
IP phone stuck&reset after call between
IP & CTI port with DPR |
|
IP phone 7960G unregisters frequently with
Callmanager |
|
IP Phone boots when an assigned URL is
invoked using a message buttn |
|
Sometimes phone does not report DSP keep
alive timeout |
|
Services screen exits- RTPRx, refresh
header and volume adjust |
|
7960 can not anwer call when in Service
menu |
|
Select Unknown number entry frm miss/rec
calls display strange ASCII |
|
Idle timeout used for Priority 1 Push Urls |
|
Cancel in Edit Dial deletes digits |
|
Push + configuration plane results in
corrupt display and 404 |
|
Phone lock icon on Network config menu
doesnt change to unlock |
|
Build ES load for BT |
|
PIX drops TFTP requests from IP Phones 7960
with extra byte 0x80 |
|
IP Phone handset/headset microphone volume
too low or too high |
|
Display TASK stack for some tasks is not in
correct order. |
|
Precedence Call Waiting does not work on handset
sometimes |
|
Non-english caller id garbles 7910 display |
|
Update copyright year on mid-range IP Phone
boot display |
|
7940/60 cant answer on handset if directory
page open |
|
Priority=0 URL push not execute when phone is
in Directory screen |
|
IP Phone services not responding after XML
parser error [4] |
|
entries in PlacedCalls are duplicated |
|
select CCC service on 7960/7940 causes hanging
or Host Not found |
|
7960 crashes with certain traffic to its
HTTP server |
|
Phone SW responds to TCP messages from
SA=224.0.0.0/4 |
|
Phone closes connection during registration
leads to reset problems |
3.3-Devpack-32 |
|
XML tags CPTONE_SIT and
CPTONE_PREC_RINGBACK not found gateway-tone. |
|
Call forwarded to PSTN get disconnected
after a brief ring |
|
6608 T1 CAS channel Busy-out Feature |
|
Audio Bleedover/Crosstalk on 6608 |
|
Complete CAS trunk not registering on 6608 |
|
6624/6608 GWs fail to register when its IP
address is changed |
|
Port direction is not reflected in WS-X6608
port config details page |
3.3-Devpack-31 |
|
7970- Extra line in To Barge call history
record |
|
Throbber no longer displays |
|
Phone doesnot retry DHCP after lease
expiration |
|
Envelope icon for voice message disapper
after power cycle |
|
Background Image Preview Mode causes not to
Exit |
|
7970 does not allow maximum valid port
value for RTP streaming |
|
7970 fail to regsiter after restarted from
CCM |
|
Security- TFTP hunt not working correctly |
|
Idle Url Displays when Call Active |
|
7970 CDP does not go to high power when Req
IDs dont match |
|
7970- Phone does not take new user locale |
|
AVVID- IP Communicator strips the leading 0
when displaying the time |
|
7970 doesnot give any info of incoming call
when in settings menu |
|
7970 will not work some dates in Feb., leap
year |
|
Requesting selections msg stays when
thumbnail image not found/wrong |
|
Phone crashes when failover to SRST |
|
Background Images on TFTP server stop
displaying in selection menu |
|
First tftp request with dhcp disable gets a
timeout |
|
Edit Dial and Predial do not have prompt messages |
|
Conference calls record not correct |
|
7970 cant display 24 digits DN |
|
Extra entries in PlacedCall list for
Transfered call |
|
Wrong display of Placed Calls when
7970phone is added to conference |
|
No history record for Meetme conference
call |
|
Inconsistent Behavior - Call History
Indexing |
|
QRT softkey does not work for 7970 phone in
CONNECTED status |
|
phone does not reboot after partial then
full user locale update |
|
7970- From Conference entry in call history
record has extra line |
|
7970 Hoot and Holler service does not work |
|
7970 cant fallback to primary CCM |
|
Call information not displayed when
directories call history is full |
|
7970 stuck after selecting on non-active
Audio Preferences |
|
Line Keys do not Dial from XsiDirectory
object |
|
Call History Cleared message prompt too
long |
|
7970 does not recover after CM Down
Features Disabled |
|
7970 prompts no error messages with some
empty URLs |
|
7970 call history record for parked call
inconsistant w/ 7960 |
|
Display issue with primary line/time |
|
EditDial only display 13 digits of a phone
number |
|
Touch screen is inaccurate |
|
7970- Softkey should not be highlighted
after screen changes |
|
7970 does not work on January 1 2004 |
|
Missed Calls prompt should not always have
the highest priority |
|
Slider doesnt update in Brightness/Viewing
Angle |
|
Call forward animated phone icon missing
after phone reset |
|
7970- dynamic call forward icon not updated
properly after login |
3.3-Devpack-30 |
|
7970-product specific settings for display on/off
time, are missing |
|
T1 modules fail framer loopback test when
configured as conf ports |
|
Change playout delay config to allow 10ms
minimum |
3.3-Devpack-29 |
|
6608 does not follow q921 spec for frame
rej |
|
T1 modules fail framer loopback test when
configured as conf ports |
|
Some fax/phone devices dont detect ring
tone generated by X6624-FXS |
|
There is no SNMP OID for Non-IOS gateways |
|
Partial failover of MGCP gateways leaves
gateways nonfunctional |
|
6608 sends NTFY to wrong channel on E1 |
|
FAC/CMC need Elvis card to play prompt tone |
3.3-Devpack-28 |
|
ATA188 doesnt support consult transfer in ITS
environment |
|
7902 reset when making a call after reset
by CM |
|
ATA cannot recognize CDP packet greater
than 500 bytes long |
|
Wrong ringback tone in network locale |
|
ATA does not implement IP survivability in
SCCP mode |
|
ATA does not recognize 802.1q encapsulated
CDP packet |
|
ATA does not support native VLAN same as
voice VLAN |
|
ATA does not detect and recover from
duplicate IP |
|
ATA-186 does not respond to StationConnectionStatisticsReg
SCCP msg. |
|
Call Waiting cannot answer incoming call on
ATA with dualline |
|
Phone line polarity may stay negative if
DTMF caller ID method used |
|
ATA G.729 encoder create fuzzy voice for
some words |
|
ata does not re-register with SRST reference
after reset |
|
Voice quality (MOS) too low for G.729a
calls |
|
Display of translated number different
depending on the phone model |
|
7905/7912 cannot replay DTMF tones when it
receives keypadbutton msg |
|
7912G Resets when using Fastdial Feature on
3.3.3sr1 |
|
phoneSetDisplay does not work but returns
success on 7905/7912 |
|
Extra-7902/7905/7912 silence suppression
not working |
|
7902 IVR goes to unknown state |
|
7912 does not re-register with SRST router
after reset |
|
7912 reboots if Corporate directory returns
more than 32 entries |
|
Push to 7912G fails |
|
7905/7912 has noise in Voice Mail
announcement in SCCP |
|
7912 can not show GoodMenu.xml |
|
7960 cannot display originating DN when
dest. has missed calls |
|
KeyPressedEv-Extra KeyPressedEv generated |
|
DTMF tones sound bad when volume is high
and mixing another signal |
|
Max. string in PAB name field cause 7960 not
able to query info |
|
Phone looses its session cookie with PAB |
|
Configurable DSCP support for
services(HTTP) on skinny devices |
|
Configurable DSCP support for config
connections(TFTP,DHCP,DNS) |
|
No ICMP port unreachables from IP phone |
|
7960/40/10 Loudness Rating for |
|
IP Phone dials first fast dial entry with
logo present. |
|
Headset cant be disabled if it was enabled
when disabled from UI |
|
IP7910 gives misleading msg when |
|
Phones randomly reset after upgrade to
3.3(3) |
|
Build next authenticated test load |
|
Build ip phone engineering special v50_t003 |
|
Extension Mobility Login/Logout causes
phone to reboot |
|
Phone does not boot up if there is not
enough RAM |
|
Phone rings differently when ring type is
set to default |
|
Phone fail to come up with signed image
after CCM upgrade to 3.3 |
|
DSP mismatch with signed image upgrade
failure |
|
Phone fails to detect some invalid IP
add/subnet mask combos |
|
79XX phones display part of the no. dialed
after failing over |
|
Cannot predial out when receiving call on
shared line |
|
predialed digits disappear when incoming
call hangs up |
|
DSP Keepalive Timeout displayed at boot
time |
|
CM 3.3(3) 401 load does not consistently
handle cookies properly |
|
DNS query fails if more than I entry is in
th the DNS Answer |
|
MWI IS NO LONGER ILLUMINATED USING SIGNED
LOADS WITH 3.1 CISCOCM |
|
7970 should not display the incorrect IP
address |
|
midrange phone does not control the EtherRX
interupt count correctly |
|
DSP error in skinny phone |
|
Add input for load id in the build GUI |
|
Phones random reset while respin the IP
stack |
|
Mute stays on when switching from headset
to handset |
|
Phone resets on keying inputs for DirSearch
in Non English Locale |
|
Allow phone to respond to a CDP trigger
when VVLAN is not configured |
|
Add ability to capture phone reset reason |
|
796x phone have audio loss and repeated
words during CCC conf call |
|
Environment changes for build server |
|
Port locale/flash changes |
|
IP Phone stop accepting XML push after ~100
push |
|
7960 resets if Dial softkey is pressed with
blank results |
|
AVVID- Phone TCP backoff algorithm slow to
return to initial timeout |
|
Sometimes phone does not report DSP keep
alive timeout |
|
7960 can not anwer call when in Service
menu |
3.3-Devpack-27 |
|
Once you press phone key to go off hook you
cant go back on hook |
|
7935s web page retains the error msgs even
after re-login |
|
Not able to configure admin vlan via web
interface. |
|
7936- Phone could go in freez state in rare
situation |
3.3-Devpack-26 |
|
7936- Phone could go in freez state in rare
situation |
|
7936-DHCP or IP address are unconfiguarble
from the phone menu |
|
7936-Phones in hung state when srst router
is restarted |
|
7936-Telnet user name and passwd need to be
configurable |
|
No http port info in sys info of 7935s web interface. |
3.3-Devpack-25.1 |
|
Need config option for ecan-extended when
using ccm-manager config |
|
Echo Cancellation Coverage does not get a
preconfigured value |
|
Add Communicator to the list of supported
devices |
3.3-Devpack-25 |
|
MGCP gateway forced RSIP with duplicate
transID |
|
Multicast MoH stops after about 3 to 6
minutes with 6608-T1 module. |
|
NO inbound calls with a 6608 T1 CAS-ground
start |
|
CCM QED Process for supporting Ditech Ecan |
|
Extend cmapp configuration for
lineprimary/free-running for t1/e1 |
|
CCM QED Process for supporting Ditech Ecan |
3.3-Devpack-24 |
|
Transcoding G.723 with MGCP or H323 fails
in forward direction |
|
Show port on 6608/6624 shows junk value for
dns |
|
CCM QED Process for supporting Ditech Ecan |
3.3-Devpack-23.1 |
|
Transcoding G.723 with MGCP or H323 fails
in forward direction |
|
Show port on 6608/6624 shows junk value for
dns |
|
Required item indication char repeated for
Hookflash Config Params |
3.3-Devpack-22 |
|
Change Reset Behavior to Reset ATA when
both line go to idle |
|
Not possible to make 4th party conference
with ATA186 via TAPI app |
|
ATA186 load for CM 3.3(0.243) is out of
date |
|
Initially setting password through web does
not require confirmation |
|
ATA186 may need special version per
CallManager version |
|
SCCP-Multicast MoH to ATA causes CM to drop
the call |
|
Cannot open ATA webpage after more than 40
times failover/fallback |
|
doesnt send out KeepAlive if choose long
KeepAlive Interval in CM |
|
SCCP-DTMF A,B,C,D cannot be relayed through
CM |
|
ATA188 does not mark TOS for skinny packets
destined for CallManager |
|
ATA188 does not mark TOS for media packets
properly by default. |
|
NO DHCP/CDP dicover send on voice-VLAN if
Native VLan is not 1 |
|
ATA phone remain hang when IP phone
disconnect first |
|
ATA doesnot stop sending RTP when VOD is on |
|
Skinny-ATA Conference fails when failover
to SRST/fallback CM |
|
ATA cannot switch back to held call in some
cases |
|
Skinny-ATA Receives 1 way audio when
failover to SRST/fallback to CM |
|
Local tone playout reporting absent for
off-hook reorder tone |
|
ATA does not play |
|
ATA18x does not recognize DTMF digits sent
from KROWN 2000DX TTY |
|
ATA does not play MWI tone |
|
ATA transmits Call-Waiting CID ack to
far-end party |
|
ATA may not re-register to correct CM after
outage |
|
need a way to send * key out in SCCP |
|
7902 does not emit stuttered dial-tone when
in call-forward mode |
|
CP-7902G
register to CM unstable |
|
7902 reset when making a call after reset
by CM |
|
XTRA-7902 call waiting tone behavior change |
|
7902/05/12 IP phones do not use configured
packet size |
|
7912 phones reset with high broadcast
levels |
|
7912 willparticipate in an ARP storm while
using the 818A load w/SR2 |
|
XTRA-7912 reboots after pressing QRT
softkey |
|
|
|
7912G Resets when using Fastdial Feature on
3.3.3sr1 |
|
7912, callback does not work on 7905/7912
(both internal/external) |
|
Build phone loads |
|
Lennon not stop dialtone |
|
7935 unregisters from CM after 2.5 min of
call - Error CM Unavailabl |
|
CCM QED Process for supporting Ditech Ecan |
|
7920-Cannot do PickUp or GPickUp on ringing
phone |
|
7920 Does Not Work w/ Lucents QIP DHCP |
|
Ringing tone is the same when 7920 receives
a call from in/outside. |
|
7920 does not meet Part 68 volume control
range |
|
7920 Causing Unavailable IP Addresses with
CNR DHCP |
|
Option 66 Has Priority Over Option 150 With
7920 |
|
Resume the call then 7920 freeze then
reboot |
|
7920 battery drains faster with keylock
enabled |
|
7920 reboots after pressing hold and resume
while in conference |
|
7920 does not display call timer when a
call was placed with ITS |
|
7970 does not Reset upon connecting a brick
if already inline power |
|
Exit softkey grey out after initiate help
on rings |
|
Last entry in Mic selection menu cut off
when menu initially entered |
|
Cant adjust brightness in low power mode |
|
7970 Handset Sidetone too soft |
|
7970-URI SoftKey-<< doesnot work |
|
Timer Drifts causing PowerSave to not be
exactly accurate |
|
7970 not use existing config when it cant
get one from server |
|
Cant scroll down in call statistics screen |
|
7970 crashes on corrupted background image |
|
Problems when 7970 cant get full size image
from server |
|
Missing titles for directory edit dial |
|
Audio lost after call transfer |
|
QED support for polycom conference station
7936 |
3.3-Devpack-21 |
|
Hookflash failure case handeled incorrectly |
|
Show port on 6608/6624 shows junk value for
dns |
|
AIM-VOICE-30 option missing for 26XX
routers |
|
Add icon for VG224 gateway for Tracing
Search |
3.3-Devpack-20.1 |
|
NM-HD-2VE module definition w VWIC-1MFT-T1
in both shows 3 0 both |
|
CSV files missing from build |
3.3-Devpack-20 |
|
Phones random reset while respin the IP
stack |
|
Phone resets on keying inputs for DirSearch
in Non English Locale |
|
7912 - phone randomly resets |
|
7912 do not register when attached to 6500 |
|
On 7905 phone LocaleInstaller version is
not available in net. set. |
|
7905 shows empty prompt when a call is on
hold |
|
7905 does not show correct prompt when 2nd
call comes in |
|
Display of translated number different
depending on the phone model |
|
Wrong ringback tone in network locale |
|
Can not answer incoming call while phone is
at Directory menu |
3.3-Devpack-19 |
|
Add VG224 to CallManager system. |
|
When MGCP 1760 reloads ANSI config is
downloaded to the E1 PRI |
3.3-Devpack-18 |
|
DNS does not fail over properly on 6608 |
|
After last digit T1-CAS gets short dial
tone & beep |
|
Disabling 6608 port doesnt disable Telco
side |
|
No inbound/outbound calls completed with
6608 T1 CAS - Ground Start |
|
Gateway page displays wrong load
information |
3.3-Devpack-17 |
|
Build phone loads |
|
midrange phone does not control the EtherRX
interupt count correctly |
|
Host not found when pressing Services |
3.3-DevPack-16 |
|
7902/05/12 IP phones do not use configured
packet size |
|
7902/05/12 IP phones lockup for 40 seconds
after call |
|
MWI IS NO LONGER ILLUMINATED USING SIGNED
LOADS WITH 3.1 CISCOCM |
|
Phones randomly reset after upgrade to
3.3(3) |
|
Extension Mobility Login/Logout causes
phone to reboot |
|
Update copyright on phone display |
|
7960/40 phone continues loading SCCP image
on failed OS79XX.TXT load |
|
Phone wont come up when wrong model of
image load to the phone |
|
No error message display on phone when the
envelope header re-order |
|
Phone resets and gets stuck in registering
cycle and have to reboot |
|
Exit key does not go up one level-goes up
to the root of directory |
|
Sustained DTMF tone played if keypad and
Endcall pressed quickly |
|
? button on 7960/40 with security phone
load not work on CM bravo |
|
TFTP Server has to be set up again if Wrong
Phone load given in CCM. |
|
LoadSigning- Unable to load diag image |
|
Tone file Unavaliable dispay when 7960/7940
reset |
|
one way / no way audio between IP Phones |
|
Phone does not failover to next DNS server
on RCODE=Server failure |
|
IP phone doesnt get IP address via cable
modem connect to UBR7223 |
|
XML Push to IP Phone requires double submit |
|
Packet loss experienced on PC port |
|
7960 not update IP address after second
DHCP request |
|
Shared phone keeps ringing after the call
is ended immediately |
|
Very high noise heard when mute is pressed
on 79XX phones |
|
Display of 1st call is removed on using
Speaker button & resume soft |
|
Duplicated RTP sequence numbers cause phone
to duplicate words |
|
Phone accepts load larger than it can boot
up |
|
SCCP messages should have DSCP value 011000
(Class 3) |
|
Phone gets stuck when a DN of max digits is
used for second line |
|
PUSH performance on 7940/60 is unacceptable |
|
All http communication quits working on
phone. |
|
IP Phone to IP Phone Echo When One Party
Has Volume 75% or Higher |
|
Push auth failure returns error = 0 instead
of 4 |
|
VG248 VGC port 0 Incorrectly registers as
Virtual Phone Type |
3.3-DevPack-15.1 |
|
6608 Gateway is unable to go operational
because of missing file |
3.3-DevPack-15 |
|
Fax Failures when faxing from Fax Machines
to a Fax App |
|
Fax Relay/Passthrough on 6608 with 2600
broken in D00403030020/3.3(2 |
3.3-DevPack-14.1 |
|
Cat6k T1/E1 not getting registered with
CallManager |
3.3-DevPack-14 |
|
User not getting proper greeting on a
scenario and going to 2nd span |
|
6624 DSP can not recognize the DTMF after
first call |
|
fax passthru 6608/24 consistently failing,
dt debugs proto violation |
|
WHALE- Seg/Reassembly, ccm could not reassembly
SEGMENT from ccm |
|
Port configuration display on 6624 ports
incorrect |
|
Multicast MOH intermittently works on 6608 |
|
New image naming convention for 6608/6624 |
3.3-DevPack-13 |
|
Add device support for 7920 phone |
3.3-DevPack-12 |
|
WS-X6624-FXS WS-X6608-T1/E1 mods not
working with WS-X6148-GE-TX |
3.3-DevPack-11 |
|
No dial tone on 6624 FXS ports |
|
WS-X6624-FXS WS-X6608-T1/E1 mods not
working with WS-X6148-GE-TX |
|
6608 T1 CAS port stops processing calls |
|
Cisco IP Phone display sometimes shows a
repeated first digit on outgoing calls. |
|
Cisco IP Phone reboots and cannot register
to Cisco CallManager when the CallManager IP address contains four sets of
three digits each (for example, 100.100.100.100). |
|
Cisco IP Phone displays a huge MaxJtr value
on the Call Statistics screen, and the RxDisc value changes from 0000. The
audio may cut out for 1 or 2 seconds. |
|
In the Hungarian locale, incorrect text
displays when a call is parked. |
|
Cisco IP Phone 7940/7960 does not display
registration reject message if autoregistration is disabled. |
|
Cisco IP Phone on auxiliary VLAN
reconfigures IP when link toggles. |
|
Line text labels for speed dials on the
second Cisco IP Phone 7914 Extension Module disappear when the network locale
is changed. |
|
The system does not collect all digits when
the user dials quickly. |
|
Packet loss occurs on PC port. |
|
Very high noise heard when the Mute button is
pressed on Cisco IP Phone models 79XX. |
|
Shared Cisco IP Phone continues to ring if
the call is ended immediately after answering. |
3.3-DevPack-10.1 |
|
SF and AMI being removed from 6608T1 from
3.2, 3.3 and 4.0 |
3.3-DevPack-10
Syncronized
Firmware and other Device Related files with 3.3(3)
3.3-DevPack-09.1 |
|
max echo canceller tail length should be configurable
in XML file |
3.3-DevPack-09 |
|
Some fax/phone devices dont detect ring
tone generated by X6624-FXS |
|
DSP 4.1 upgrade for Cat6k gateway |
|
T1 Span locked up after load test |
|
Conference ports are not released after
reseting the Call Manager |
|
T.38 Fax fails through MTP when used with
40 ms packtzn in G729 |
|
max echo canceller tail length should be
configurable in XML file |
|
ProviderOpenFail after a fresh install with
Restart Prompt needed |
|
Change time mentioned in the dialogue box
during FP1 upgrade |
3.3-DevPack-08.3 |
|
Line Text Label feature Not available on
this device |
3.3-DevPack-08.2 |
|
Display Instance Refers To An Undefined
Rule |
3.3-DevPack-08.1 |
|
New 6608 modules will not register as a
conference bridge or MTP |
3.3-DevPack-08 |
|
CP tones are not played by 6624 if
gateway-tones.xml is absent. |
|
6608 blade with 3.3 CCM shows echo cancel
disabled for voice calls |
|
Cat-66080E1 (0.5 second) Voice Clipping due
to out of sequence RTP |
|
DNS does not fail over properly on 6608 |
|
T1 voice ports do not configure correctly
in text config mode |
|
There is no audio path if transcoder is
used with G.723 |
|
6608 CFB and Xcoder should use old to
register if download fail |
|
conf bridge with static IP Addr dont come
up if disabled and enabled |
|
The IP Conference Station cannot handle
jitter and reorder packets the way a Cisco IP Phone 7960 can. |
|
The IP Conference Station hangs when when
picking up a parked call. |
|
When using an IP Conference Station in a
conference call with a PSTN phone, there is white noise in the back ground
that leads to voice clipping heard by all parties on the call. |
|
During a conference call, there is
intermittent voice loss on the IP Conference Station. |
|
During a conference call, the The IP
Conference Station intermittenly hangs when a second party is added to the
call. An error message is displayed and then the IP Conference Station starts
re-registering. |
|
The IP Conference Station can only display
8 or 9 characters in the top right corner of the LCD display, which shows the
phone's directory number. If the directory number is more than 8 or 9 digits,
it is truncated. |
|
The IP Conference Station can not handle
packets that vary in size other than 20 or 30 ms, causing some of them to be
dropped. |
|
When dialing into an Interactive Voice
Response (IVR) system, there is some chopiness on the call. |
|
When dialing a call via Cisco Conference
Connection on the IP Conference Station, the voice quality is very
robotic-sounding. |
3.3-DevPack-07.1 |
|
Display Instance Refers To An Undefined
Rule |
3.3-DevPack-07
Added
New Device Support for the Cisco IP Phone 7912g
3.3-DevPack-06 |
|
|
Added New Device Support for the Cisco IP Phone
7902g |
AXL restart request causes reset. |
|
Intrcpt key looks inactive. |
|
Phone resets with line rate traffic from PC
port. |
|
Assistant watch area is corrupted in status
window for Japanese locale. |
|
HTTP error [8] after user aborts search of
corporate directory. |
|
Phone does not hear DTMF tones generated by
other devices. |
|
Answer softkey does not appear when dialing
with receiver still on hook. |
|
Voice quality report for last call is
incorrect. |
|
The German translation of "Edit
Dial" is incorrect. |
|
Phone displays model number and serial
number as invalid information. |
|
Some English text in Ringer menu not
translated. |
|
Phone will not go off hook when in missed calls
directory. |
|
Handset Send Frequency Response and SLR
changed. |
|
Phone gets stuck in SRST mode when primary
CM DNS cannot be resolved. |
|
Phone does not properly display all
available characters when spelling using the keypad. |
|
Prompt has incorrect Greek translation. |
|
Cisco CallManager spelled incorrectly in
Network Settings. |
|
Phone displays huge MaxJtr value when RTP
SSRC ID and Timestamp change. |
|
Phone incorrectly reports the number of
lost packets if no packets received. |
|
Phone resets when the user presses the Dial
softkey in the Corporate Directories. |
|
Phone loses tones and ringback after it
receives a multicast audio or text message. |
3.3-DevPack-05 |
|
Elvis/Lennon- |
|
fax passthru 6608/24 consistently failing,
dt debugs proto violation |
|
SIT tone cadence is not right in gw xml
file |
|
Modem calls failed to connect successfully |
|
private community works without setting in
CCM |
|
Gateway does not respond to Connection
Audit correctly |
|
conference call drops when call manager
comes up |
|
private community works without setting in
CCM |
|
DSP gets reset when 3 or 4 frequencies are
to be played concurrently. |
|
No dial-tone on FXS port |
|
Missing support for 10-30ms packetization
on DT24+ |
|
Fax Passthrough calls fail with Cat6k 6608
as MTP with CCM |
|
7935 Can not handle Jitter and reorder
packets the way a 7960 can |
|
The IP Conference Station hangs when when
picking up a parked call. |
|
White noise and voice clipping with PSTN
users |
|
During a conference call, there is
intermittent voice loss on the IP Conference Station. |
|
Conference causes 7935 to unregister |
|
7935 display should show more than 8 digits
for DN on display |
|
7935 can not handle variation causing some
to be dropped |
|
When dialing into an Interactive Voice
Response (IVR) system, there is some chopiness on the call. |
|
7935 is underwater sounding with bad voice
quality |
For optimal performance, be sure that you use the Cisco IP
Telephony Locale Installer that is specific to the version of Cisco Unified
CallManager that you use. Be aware that
all phrases may not display in the desired locale when you upgrade to a
different version of Cisco Unified CallManager.
Refer to the readme file that is posted with the Cisco IP Telephony
Locale Installer software on the following URL for the complete list of
supported languages: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/locinst/index.htm.
Each release of Cisco Unified CallManager may support a
different number of locales. The full suite of Locale Installers that work with
each applicable version of Cisco Unified CallManager can be found on http://www.cisco.com after the English
version becomes available. You can download the Locale Installers for all
languages that are supported with Cisco Unified CallManager from the following
location: http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml.
1.
Note: When using
locales, Cisco recommends that you wait until the locale installer that
specifically supports the version of Cisco Unified CallManager that you use
becomes available before you upgrade your system. Because some incompatibilities may exist
between releases, be sure to only use the locale installer that specifically
supports your version of Cisco Unified CallManager.
Cisco documentation and additional
literature are available on Cisco.com. Cisco also provides several ways to
obtain technical assistance and other technical resources. These sections
explain how to obtain technical information from Cisco Systems.
Cisco.com
You can access the most current Cisco
documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at
this URL:
You can access international Cisco
websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
For additional information about Cisco
Unified CallManager, refer to the following documentation:
To access the documentation suite for
voice products, navigate to the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/voice/.
To access the latest software upgrades
and related documentation for
Cisco Unified CallManager, navigate to the following URL and then choose the
applicable version: http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml.
Cisco documentation and additional literature are available in a
Documentation DVD package, which may have shipped with your product. The
Documentation DVD is updated regularly and may be more current than printed
documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can order a
Cisco Documentation DVD (product number DOC-DOCDVD=) from the Ordering tool or
Cisco Marketplace.
Cisco Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco Marketplace:
http://www.cisco.com/go/marketplace/
You can find instructions for ordering
documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in
these ways:
You can send comments about technical
documentation to bug-doc@cisco.com.
You can submit comments by using the
response card (if present) behind the front cover of your document or by
writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
We appreciate your comments.
Cisco provides a free online Security
Vulnerability Policy portal at this URL:
http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform these
tasks:
A current list of security advisories
and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt
If you prefer to see advisories and
notices as they are updated in real time, you can access a Product Security
Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this
URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Cisco is committed to delivering secure products. We test our
products internally before we release them, and we strive to correct all
vulnerabilities quickly. If you think that you might have identified a
vulnerability in a Cisco product, contact PSIRT:
We encourage you to use Pretty Good Privacy (PGP) or a compatible
product to encrypt any sensitive information that you send to Cisco. PSIRT can
work from encrypted information that is compatible with PGP versions 2.x
through 8.x. Never use a revoked or an
expired encryption key. The correct public key to use in your correspondence
with PSIRT is the one that has the most recent creation date in this public key
server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also reach PSIRT by telephone:
For all customers, partners, resellers,
and distributors who hold valid Cisco service contracts, Cisco Technical
Support provides 24-hour-a-day, award-winning technical assistance. The Cisco
Technical Support Website on Cisco.com features extensive online support
resources. In addition, Cisco Technical Assistance Center (TAC) engineers
provide telephone support. If you do not hold a valid Cisco service contract,
contact your reseller.
The Cisco Technical Support Website
provides online documents and tools for troubleshooting and resolving technical
issues with Cisco products and technologies. The website is available 24 hours
a day, 365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco
Technical Support Website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a user ID or password, you can
register at this URL: http://tools.cisco.com/RPF/register/register.do
2.
Note: Use the Cisco Product
Identification (CPI) tool to locate your product serial number before
submitting a web or phone request for service. You can access the CPI tool from
the Cisco Technical Support Website by clicking the Tools & Resources link
under Documentation & Tools. Choose Cisco Product Identification Tool from
the Alphabetical Index drop-down list, or click the Cisco Product Identification
Tool link under Alerts & RMAs. The CPI tool offers three search options: by
product ID or model name; by tree view; or for certain products, by copying and
pasting show command output. Search results show an illustration of your
product with the serial number label location highlighted. Locate the serial
number label on your product and record the information before placing a
service call.
Using the online TAC Service Request
Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service
requests are those in which your network is minimally impaired or for which you
require product information.) After you describe your situation, the TAC
Service Request Tool provides recommended solutions. If your issue is not
resolved using the recommended resources, your service request is assigned to a
Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you
do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2
service requests are those in which your production network is down or severely
degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service
requests to help keep your business operations running smoothly.
To open a service request by telephone,
use one of the following numbers:
Asia-Pacific: +61
2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55
55
USA: 1 800
553-2447
For a complete list of Cisco TAC
contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
To ensure that all service requests are
reported in a standard format, Cisco has established severity definitions.
Severity 1 (S1)—Your network is “down,”
or there is a critical impact to your business operations. You and Cisco will
commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an
existing network is severely degraded, or significant aspects of your business
operation are negatively affected by inadequate performance of Cisco products.
You and Cisco will commit full-time resources during normal business hours to
resolve the situation.
Severity 3 (S3)—Operational performance
of your network is impaired, but most business operations remain functional.
You and Cisco will commit resources during normal business hours to restore
service to satisfactory levels.
Severity 4 (S4)—You require information
or assistance with Cisco product capabilities, installation, or configuration.
There is little or no effect on your business operations.
Information about Cisco products,
technologies, and network solutions is available from various online and
printed sources.
·
Cisco Marketplace provides a variety of Cisco books,
reference guides, and logo merchandise. Visit Cisco Marketplace, the company
store, at this URL: http://www.cisco.com/go/marketplace/
·
Cisco Press publishes a wide range of general networking, training and
certification titles. Both new and experienced users will benefit from these
publications. For current Cisco Press titles and other information, go to Cisco
Press at this URL: http://www.ciscopress.com/
·
Packet magazine is the Cisco Systems technical user magazine for
maximizing Internet and networking investments. Each quarter, Packet delivers
coverage of the latest industry trends, technology breakthroughs, and Cisco
products and solutions, as well as network deployment and troubleshooting tips,
configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access
Packet magazine at this URL: http://www.cisco.com/packet
·
iQ Magazine is the quarterly publication from Cisco Systems designed to help
growing companies learn how they can use technology to increase revenue, streamline
their business, and expand services. The publication identifies the challenges
facing these companies and the technologies to help solve them, using
real-world case studies and business strategies to help readers make sound
technology investment decisions. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine
·
Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering
professionals involved in designing, developing, and operating public and
private internets and intranets. You can access the Internet Protocol Journal
at this URL: http://www.cisco.com/ipj
·
World-class networking training is available from Cisco. You
can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html
CCSP,
the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks
of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and
iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar,
Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco
Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering
the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast,
EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet
Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard,
LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking
Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect,
RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe,
TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and
VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in
the United States and certain other countries.
All
other trademarks mentioned in this document or Website are the property of
their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (0501R)
Copyright
© 2007 Cisco Systems, Inc. All rights reserved.