Cisco Unified CallManager Device Package 4.1(89.0)
Release Notes
These Device Package release notes contain important information about
installation procedures and resolved caveats for Cisco Unified CallManager
Device Package release 4.1(89.0).
Note: Before you install this Cisco Unified CallManager
Device Package, Cisco recommends that you review the “Important
Notes” section for information about issues that may
affect your system.
Determining
the Software Version
Compatibility
Matrix and Supported Upgrades
Important
Notes & Recommendations
Resolved
Caveats for Cisco Unified CallManager Device Package
Locale
Installer for Cisco Unified CallManager
Cisco
Product Security Overview
Reporting
Security Problems in Cisco Products
Obtaining
Technical Assistance
Cisco
Technical Support Website
Definitions
of Service Request Severity
Obtaining
Additional Publications and Information
This
document provides installation instructions for this Cisco Unified CallManager
Device Package and endpoint related changes.
Note: Failure to follow installation instructions as
described may result in inconsistent Cisco Unified CallManager behavior.
Make sure that you install and configure this release of Cisco Unified
CallManager on approved Cisco hardware. You can access the correct
Cisco-approved server configuration at the following URL: http://www.cisco.com/en/US/products/hw/voiceapp/ps378/prod_brochure_list.html.
You can determine the version of Cisco Unified CallManager software that
is running on your server by accessing Cisco Unified CallManager Administration
and then clicking Details.
This Cisco Unified CallManager Device Package release is compatible with
the following Cisco Unified CallManager versions.
4.1(3) |
Note: Review the history file in your Cisco Unified
CallManager in order to determine what Device Package you currently have
installed. If you are preparing to install an older Device Package than is
currently on your Cisco Unified CallManager, you will receive the following
error “This Device Package is older than the Device Package already Deployed. It is recommended that you should exit
now. EXIT now?”
NOTE: Be aware that the release of Cisco IP telephony
endpoints does not always coincide with Cisco Unified CallManager releases. It
is recommended that you upgrade to the latest firmware. For the most current
compatibility combinations and defects, refer to the following locations:
Endpoint firmware: http://www.cisco.com/cgi-bin/tablebuild.pl/ip-7900ser Endpoint documentation, including release notes:
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_ipphon/english/
Cisco Unified CallManager
Device Package 4.1(89.0) includes the following firmware versions:
Firmware |
4.1-Devpack 89 |
7914 14-Button Line
Expansion Module |
S00105000400 |
7915-12 Button
Extension Module |
B015-1-0-3 |
7915-24 Button
Extension Module |
B015-1-0-3 |
7916-12 Button
Extension Module |
B016-1-0-3 |
7916-24 Button
Extension Module |
B016-1-0-3 |
ATA18X |
ATA030204SCCP090202A |
Analog Access
WS-X6624 |
A00204000013
/ A0034322 |
Digital Access
WS-X6608 |
D00404000032
/ D0054322 |
|
C00104000003
/ C002E031 |
Media Termination
Point WS-X6608 |
M00104000006
/ M002E031 |
Digital Access+
Load |
D00303010033 |
IP Phone 7902g |
CP7902080002SCCP060817A |
IP Phone 7905g |
CP7905080003SCCP070409A |
IP Phone 7906 |
SCCP11.8-4-4S
|
IP Phone 7910 |
P00405000700 |
IP Phone 7911 |
SCCP11.8-4-4S
|
IP Phone 7912g |
CP7912080003SCCP070409A |
IP Phone 7920 |
cmterm_7920.4.0-03-02 |
IP Phone 7921 |
D00404000031 |
IP Phone 7921G |
CP7921G-1.3.2 |
IP Phone 7925G |
CP7925G-1.3.2 |
IP Phone 7935 |
P00503021900 |
IP Phone 7936 |
cmterm_7936.3-3-20-0 |
IP Phone 7937 |
apps37sccp.1-3-3-0 |
IP Phone 7940/7960 |
P00308010100 |
IP Phone 7941/7961 |
SCCP41.8-4-4S |
IP Phone 7942/7962 |
SCCP42.8-4-4S |
IP Phone 7945/7965 |
SCCP45.8-4-4S |
IP Phone 7970/7971 |
SCCP70.8-4-4S |
IP Phone 7975 |
SCCP75.8-4-4S |
IP Phone 7985 |
cmterm_7985.4-1-7-0 |
Note: It is very important to disable platform agents and
services, such as NetIQ and Prognosis performance monitoring, Cisco-verified
antivirus services and intrusion detection software, remote management
services, and any other monitoring applications that automatically restart
services; this action ensures that your system does not encounter issues that
are associated with these services.
Cisco
provides the following guidance to help you successfully install and/or upgrade
Cisco CallManager software:
To minimize call-processing
interruptions during the upgrade process, make sure that all servers are
running the same version of Cisco Unified CallManager
software before beginning this upgrade.
Make sure that the servers are
online before you begin this Device Package installation; otherwise,
pre-upgrade checks may fail or return faulty information.
For optimum performance, apply
the most current OS upgrade and SR before you install the Cisco Unified
CallManager Device Package. For more
information, refer to Cisco IP Telephony
Operating System, SQL Server, Security Updates at http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/osbios.htm.
If you are using Cisco Unified
CallManager Security Agent, you must DISABLE this software and then restart
your system before you proceed with this installation.
All nodes in the cluster run
through a database replication check during the upgrade process as an extra
measure, even though the publisher's database replication check should catch
any replication errors clusterwide.
If you encounter
a warning message on any node during this check, make sure that you stop the
installation process and check the log files. Follow the recommendations listed
below if the log file displays any of the following messages:
“All agent-implementing
jobs are waiting to start”
“At least one
agent-implementing job is attempting to execute after a previous failure“
“At least one
agent-implementing job has failed to execute successfully“
Be sure to DISABLE any
antivirus and intrusion detection software, along with any other security
services; then, restart your server before you run the upgrade process. You must manually re-enable these services
after the installation is complete.
Make
sure that you disable the following Cisco-verified platform agents and
applications; these products may interfere with the Cisco Unified CallManager
installation:
Server
management agents
VOIP
monitoring/performance monitoring
Remote
access/remote management agents
Note: It is very important to disable platform agents and
services, such as NetIQ and Prognosis performance monitoring, Cisco-verified
antivirus services and intrusion detection software, remote management
services, and any other monitoring applications that automatically restart
services; this action ensures that your system does not encounter issues that
are associated with these services.
Note: To verify that the installation completed
successfully, follow the instructions in Step 5 in the Installation Instructions section.
Note: Cisco recommends that you apply this Device Package
during a maintenance window.
Procedure
NOTE: Apply this patch to all of your Cisco CallManager
servers, beginning with the publisher server and TFTP server.
When applying this Device Package to enable new device support, a cluster-wide reboot is required for those devices to register
successfully. A clusterwide reboot IS NOT required when running to update existing firmware/support.
If installing on a Cisco Unified CallManager
version earlier than 4.1(3)sr2, the following
message will be displayed: “Install on all nodes is
required. All nodes will be rebooted as part of the
installation.”
If installing on Cisco Unified
CallManager 4.1(3)sr2 (recommended), the
following message will be displayed: "Install on Publisher and TFTP server
is required. Installation on all nodes is highly
recommended." A clusterwide install/reboot is required.
Perform the
following procedure to install Cisco Unified CallManager Device Package X.X.exe:
1. Download the ciscocm-4-1-DevPack-X.X.exe file to your hard
drive. Make a note of the location where you saved the file.
2. Double-click on the downloaded file to begin the
installation.
3. Click Yes when the
installation process displays a message that asks if you want to install this
Device Package.
4. The remainder of the installation process continues
without any additional user input.
5. Towards the end of the install it will prompt you
"Update ALL devices firmware defaults?", (IMPORTANT) If you click
"yes", it will change the default firmware load for all devices to
the latest load packaged with this device pack, click "no" if you
want to change the loads manually yourself later.
Note: In order to change the loads manually, you do NOT
need to reinstall this Device Package. The new files will be present in the
C:\Program Files\Cisco\TFTPPath folder. Go to CCMAdmin->System->Device
Defaults and manually change the name of the load file (for specific device(s))
to the new load and click UPDATE. Next, reset the affected devices for them to
upgrade to the new load.
The system will ask you if you want to view
the logfile when the installation is complete.
6. Verify that the installation completed successfully
by taking the following actions:
a. When the system prompts you to view the log
file, if the number of errors listed in the dialog is "0", you
can select No.
b.
If the number of errors
detected was greater than 0, select Yes
to view the logfile and scroll down to the end of the log file. The
errors section at the bottom of the log file will be updated with a
corresponding severity.
c. Reset affected devices in order for them to obtain new
firmware loads, or reboot the cluster.
Note: If the TFTP server is a separate server from the
Publisher, the Cisco TFTP service needs to be stopped and restarted on the TFTP
server before performing this step, unless the cluster (including the TFTP
server) is being rebooted.
Change the device defaults for devices you wish to roll
back. From the Cisco Unified CallManager Administration page go to
System/Device Defaults and set the devices that were changed previously back to
their previous firmware setting. Select update, and then reset those
devices.
The system may create or edit the following log
files during the installation process:
c:\program files\common
files\cisco\logs\CCMPatch\Cisco Unified CallManager X.X DevPackXX
Installation YYYY-MM-DD HH.mm.log (this file is also accessible by navigating
to the Start menu shortcut "Cisco Install Logs" under the CCMPatch
folder)
c:\install\dbinstall\dbinstallXXX.txt
c:\program
files\common files\cisco\logs\CCMPatch\sqlX.txt
c:\program files\common
files\cisco\logs\history.log
Known Caveats in this DP:
The installshield engine (ikernel.exe)
could not be launched |
This Device
Pack contains the following fixes:
4.1-Devpack
89 |
|
ATA18X |
|
Check-in ATA
SCCP firmware version 3.2(4) to CUCM |
|
7906G/11,7941/61, |
|
8.4(4) QED
files check in |
4.1-Devpack
88 |
|
7937 1.3(3)
CUCM vob check in defect |
|
GlobeLion -
Host Movement for midrange phones |
4.1-Devpack
87 |
|
Error in IP
Phone Rules file causes sidecar to not register to CUCM |
|
SWT-no secure
tone defination in g3-tones.xml file . |
|
Checking in
bkem(7916/7915) 1-0-3 firmware |
|
TNP phone
update needed for Venezuela TZ change |
|
7931 stops
displaying the timer counter of an onhold call. |
|
Second line
gets focus when BLF w/ button is pressed. |
|
7961/41 PLK
Issue,DND shows ??? on display |
|
lineDial()
fail after SIP ph w/AutomaticRecordOption sets up conference |
|
7961G-GE
Multicast Slow Throughput - disable flow control on BCM phones |
|
PLK icon does
not display very well |
|
Failed to blindxfer
the call during the conference |
|
strace
sometimes stops outputting syslogs |
|
SendDigits
URI not working |
|
Inconsistency
between alerting name and Placed call on screen display |
|
SECD API
addition to support SecurityInfo and Certificate interface |
|
7941/61
flickering backward compatibility with 7911 flicker fix |
|
7941/61/42/62
UI doesn't refresh the soft key clearly. |
|
phone keep
play busy tone after a certain procedure |
|
7970/71 don't
respond to resets whilst at maximum number of reg devices |
|
phone sends
wrong CCM name when dhcp domain-name-servers has 63 entries |
|
IP phone
incorrectly padding out frames < 64 bytes |
|
7911 can not
switch to call UI when it is in placed call screen |
|
7911 offhook
should not dial out when call comes in at SD screen |
|
Extension
Mobility login/logout does not exit the login/logout screen |
|
call through
H.323 ICT, hold, then resume, call dropped |
|
Recording
& BiB Interactions- Not Working Properly In Unison |
|
java.util.NoSuchElementException-
Hashtable Enumerator when using IPPM |
|
Double DHCP
Request send out by IP Phone |
|
R2D- Memory
leak in font support code detected |
|
Phone query's
12x Primary TFTP server before failing over to Secondary |
|
intercom call
will be dropped when there is pre-dial number |
|
Cant end
barge call when EndCall softkey is not in first page |
|
Services
display is inconsistent with Messages and Directories display |
|
Phone stops
receiving mulitcast audio after few times |
|
can not dial
from Directories after exiting from EditDial |
|
3rd gen
phones dont take Argentina TZ |
|
phone prompts
as line in use but all lines are in idle state |
|
TNP phone
downloads same image which is already in it . |
|
Disable
Speakerphone doesn't take effect after phone fallback. |
|
CTI
controlled phone generates incorrect DTMF |
|
en-bloc
feature causes non-dialable characters to be dialed |
|
CP7931/CP7911
may unregister due to CDP hold timer expiry |
|
HTTP GET with
ACCEPT header over 300 char causes 400 Bad Request |
|
Third-gen
phone does not set SEC field in DHCPDiscover message |
|
Intercom call
timer reset to 0 when settings menu acccessed during activ |
|
phone failed
to register to Windows CUCM working in mixed mode |
|
OK buttion in
the middle of navigator keypad doesn't work in 802.1x UI. |
|
Phone resets
when barging into conference |
|
Phone can
only place/answer call by softkey |
|
Can not reset
phone by **#** |
|
DTMF is not
squelched on third gen phones causing duplicate DTMF |
|
Disable
Speaker/headset doesn't take effect after phone fallback. |
|
UI- Wrong
softkey displayed in Call Details when speaker is disabled |
|
headset can
not be invoked on TNP phones |
|
Touch screen
doesn't work under Directories |
|
7921/7925 |
|
DSP restarts
when user keeps initiating and ending a barge session |
|
1-way audio
due to no Networkdown event to SCCP when switch profiles |
|
7921 always
sends authenticaton request code 128 when doing EAP |
|
Screen not
updated automatically after swap b/w Line View & Main Home |
|
Problem in
the refresh header for Cisco IP Phone 7921 Wireless |
|
GUI crashes
when application URL points to execute object with Dial URI |
|
Phone does
not reset if shared line is in use |
|
7921/7925
Need to enforce 32 char CN length limit in UI for CSR |
|
CP-792X- Call
history record populated incorrectly after firmware upgrad |
|
7921-media
not established after xml app focus restored |
|
Upgrade
failed if RESTARTing the phone from CCM |
|
Incorrect
display in Services menu when using non-English locale |
|
7921 is not
responding with proper XML error |
|
The Single
Number Reach Mobility softkey does not work with CUCME |
|
7921
application button fires URL twice |
|
7921G/7925G
on Unison does not play priority call waiting tone |
|
Disable in-band
ringtone for AUS |
|
7921-
specific Japanese is lost from user name in Local Phone Book |
|
7921- Handset
volumes may be too loud |
|
7925G and
7921G Vibrate does not executed after phone returns to IDLE |
4.1-Devpack
86 |
|
Update Cisco
7921 & 7925 support files for Release 1.3.2 |
|
7936 3.3(20)
CUCM vob check in defect |
|
7985 |
|
Active call
statistics stop updating when Call Manager failover occurs
. |
|
7985 phone
stuck in "Bad" UCM status after stress failover testing |
|
7985- Failed
to use Alternate TFTP, **#** solve the issue |
|
CUE prompts
are not heard on 7985 Phone |
|
7985 sending
malformed ICMP packet |
|
7985 not
adjust the brightness lively when pressing default key |
|
7985 does not
accept the 9th or 13th softkey |
|
7985- SRST is
given higher priority than TFTP when CCM hostname unresolv |
|
Call history
is cleared after CUCM restarts the 7985 phone |
|
7985 cannot
change background image when video mute is active |
|
7985 plays
the second ring tone for all external calls |
|
7985 always
shows the far end's alerting name in "Placed Calls" |
|
Missing sdk
version info from http header |
|
end call
softkey does not work under certain situation |
|
'255.255.255.255'
can be accepted by 7985 as a valid subnet mask |
|
7985 exceeds
maximum frame rate for H.264 |
|
IP Phone-
7985 - Upgrade libpng version |
|
7985 does not
support flow control bitrate=0 to remove video |
4.1-Devpack
85 |
|
TNP phone
update needed for Venezuela TZ change |
|
7931 stops
displaying the timer counter of an onhold call. |
|
Second line
gets focus when BLF w/ button is pressed. |
|
7961/41 PLK
Issue,DND shows ??? on display |
|
lineDial()
fail after SIP ph w/AutomaticRecordOption sets up conference |
|
7961G-GE
Multicast Slow Throughput - disable flow control on BCM phones |
|
Failed to
blindxfer the call during the conference |
|
Inconsistency
between alerting name and Placed call on screen display |
|
7941/61
flickering backward compatibility with 7911 flicker fix |
|
7941/61/42/62
UI doesn't refresh the soft key clearly. |
|
7970/71 don't
respond to resets whilst at maximum number of reg devices |
|
phone sends
wrong CCM name when dhcp domain-name-servers has 63 entries |
|
IP phone
incorrectly padding out frames < 64 bytes |
|
7911 can not
switch to call UI when it is in placed call screen |
|
7911 offhook
should not dial out when call comes in at SD screen |
|
call through
H.323 ICT, hold, then resume, call dropped |
|
java.util.NoSuchElementException-
Hashtable Enumerator when using IPPM |
|
Double DHCP
Request send out by IP Phone |
|
R2D- Memory
leak in font support code detected |
|
Phone query's
12x Primary TFTP server before failing over to Secondary |
|
intercom call
will be dropped when there is pre-dial number |
|
Cant end barge
call when EndCall softkey is not in first page |
|
Phone stops
receiving mulitcast audio after few times |
|
can not dial
from Directories after exiting from EditDial |
|
3rd gen
phones dont take Argentina TZ |
|
phone prompts
as line in use but all lines are in idle state |
|
Disable
Speakerphone doesn't take effect after phone fallback. |
|
CTI
controlled phone generates incorrect DTMF |
|
en-bloc
feature causes non-dialable characters to be dialed |
|
CP7931/CP7911
may unregister due to CDP hold timer expiry |
|
HTTP GET with
ACCEPT header over 300 char causes 400 Bad Request |
|
Third-gen
phone does not set SEC field in DHCPDiscover message |
|
Intercom call
timer reset to 0 when settings menu acccessed during activ |
|
phone failed
to register to Windows CUCM working in mixed mode |
|
Phone resets
when barging into conference |
|
DTMF is not
squelched on third gen phones causing duplicate DTMF |
|
UI- Wrong
softkey displayed in Call Details when speaker is disabled |
|
7937 1.3(2)
CUCM vob check in defect |
|
Add remote
hold icon to 7914 |
|
Adding 8.4(2)
QED features |
4.1-Devpack
84 |
|
Adding
8.4(1)SR2 to CUCM |
|
7961G-GE
Multicast Slow Throughput - disable flow control on BCM phones |
|
Phone query's
12x Primary TFTP server before failing over to Secondary |
|
Phone stops
receiving mulitcast audio after few times |
|
Assistant
Phone gets hanged while making intercom call to two different. |
|
CTI
controlled phone generates incorrect DTMF |
|
en-bloc
feature causes non-dialable characters to be dialed |
|
CP7931/CP7911
may unregister due to CDP hold timer expiry |
|
phone failed
to register to Windows CUCM working in mixed mode |
|
DTMF is not
squelched on third gen phones causing duplicate DTMF |
|
Adding
8.4(1)SR2 to CUCM |
|
Headset
sidetone does not sound loud enough |
|
7960/40 SCCP
phone resets if set too long URL directories in CCM |
|
CUCM 6.1.1,
DND set receive a call, causes feedback |
|
7925 |
|
Check-in
Cisco 7925 firmware version 1.3(1) to CUCM |
|
Update
'devicelistx.asp' to support Cisco 7925 |
4.1-Devpack
83.1 |
|
After install
of sr8 6608 GW not receiving new code version |
4.1-Devpack
83 |
|
Adding
8.4(1)SR2 to CUCM |
|
7961G-GE
Multicast Slow Throughput - disable flow control on BCM phones |
|
Phone query's
12x Primary TFTP server before failing over to Secondary |
|
Phone stops
receiving mulitcast audio after few times |
|
Assistant
Phone gets hanged while making intercom call to two different. |
|
CTI
controlled phone generates incorrect DTMF |
|
en-bloc
feature causes non-dialable characters to be dialed |
|
CP7931/CP7911
may unregister due to CDP hold timer expiry |
|
phone failed
to register to Windows CUCM working in mixed mode |
|
DTMF is not
squelched on third gen phones causing duplicate DTMF |
4.1-Devpack
82 |
|
Adding
Display Refresh Flicker Correction feature |
|
Update 7925
CSV & XML files for FCS |
4.1-Devpack
81.1 |
|
SCCPxx.8-4-1ES2
should be SCCPxx.8-4-1SR1S |
4.1-Devpack
81 |
|
Font file in
CUCM default US-english locale corrupted |
|
No " |
|
Adding 3rd
Gen firmware 8.4(1)SR1 to CUCM |
|
Adding 8.4(1)
to CUCM |
4.1-Devpack
80 |
|
Wrong load
name for H/W CFB in the device default page |
4.1-Devpack
79 |
|
Check-in
Cisco 7921 firmware version 1.2(1) to CUCM |
|
Update 7921
support files for Release 1.2 |
4.1-Devpack
78 |
|
7937 1.2(1)
CUCM vob check in defect |
|
3.3(16) and
3.2(19) CCM vob commit |
4.1-Devpack
77 |
|
7925 |
|
Add 7925
support files (CSV, XML, GIF) to CUCM |
4.1-Devpack
76 |
|
Adding 8.3(5)
phone firmware to CUCM |
|
7985 |
|
CCMUser page
has no user guide for 7985 |
|
7985 phones
reply with ResponseItem Status="OK" instead of "0" |
|
Some of the
fields on the phone's XML web pages have wrong information |
|
SSH password
field is only 7 characters wide |
|
Unable to
register 7985 to TFTP server which is not default |
|
7985 fails to
pickup parked call/initiate adhoc hardware conference |
|
CfwdAll
Display message is not getting refreshed. |
|
7985-
Changing the CCM version doesnt change the background image. |
|
7985 need to
support non-overlapping preference for video codecs |
|
Phone ignores
CDP when using Admin VLAN with PC Voice VLAN Disabled |
|
7985 not
displaying status correctly if MeetMe conference creater . |
|
Operational
impacting debug commands should not been available by telnet |
|
when incoming
call from IPVC, 7985 does not display correct video rate |
|
7985
"Download User Guide" link does not link directly to User Guide |
|
7985- Unable
to make call from directory, from 2nd/other lines. |
|
7985- If DNS resolution
failed to CCM1, CCM1 doesnt appear in CM list. |
|
CCM4.2 -
Cisco 7985 No Red Pickup Light Notification |
|
Visual Pickup
Notification sometimes does not overwrite status line |
|
Network
statistics stop refreshing when switching screens |
|
7985-video-disabled
& background image changed, new image seen other end |
|
7985- Phone
displays "Rejected by CM "%S"" when autoreg disabled. . |
|
7985-
Instance of call on phone not visible in a scenario. . |
|
7985- When
all CUCMs service stopped, 7985 should display Registering. |
|
Phone service
input fields don't display pop-up box showing char choices |
|
7985- 20ms
packetization and phone still gets stuck intermittently |
|
Need to
remove RFC2833 Disabled parameter for 7985 phone in CCM Admin |
|
7985- Status
Not Updated Until OffHook/OnHook |
4.1-
Devpack 75 |
|
6608/6624 |
|
6608Fix help
file URL for CCM 6.0 |
4.1-Devpack
74 |
|
7940/7960 |
|
Pressing
Cancel while Requesting RingList File displays two Ring Type |
|
7960 shows 1
packet RXLost at start of every call |
|
Firm 8.0.5 , Delay in accessing corporate directory on
7940/7960 Phones. |
|
Secure ephone
configured with octal Dn for more than 3 button reload |
|
7940 Russian
Phones show garbage characters in Calls History |
|
7960 is not doing
HTTP redirects properly when connected to Phone Proxy |
|
7960/40
EAPOL-Logoff functionality |
|
SCCP phone
being told to play DTMF * but playing DTMF C |
|
After a
callback warning pressing dial plays dial tone and no ring back |
4.1-Devpack
73 |
|
Locale not
displayed properly after changing from Japanese to English |
4.1-Devpack
72 |
|
Announcement
identified- 53 not found. |
4.1-Devpack
71 |
|
Adding 8.3(4)SR1
phone firmware to CUCM |
4.1-Devpack
70 |
|
7937 1.1(1)
CUCM vob check in defect |
4.1-Devpack
69 |
|
Link 'View
the User Guide for your phone' not available for 7911/7970 |
|
PLKs on 8.3
phones have "???" labels when talking to pre-6.0 CCM |
|
7921 |
|
Check-in
Cisco 7921 firmware version 1.1(1) to CallManager |
|
7940/7960 |
|
DNS Response
Parsing Stack Overflow |
4.1-Devpack
68 |
|
Update 7921
CSV and XML files for Release 1.1 FCS |
|
6608 |
|
E1 Port on
WS-6608 5.4(2) not replying to external ping (ICMP) packets. |
|
ICMP is
disable for 6608 Device |
4.1-Devpack
67 |
|
Hear clicking
when headset is attached and display is on |
|
No audio if
source reset RTP timestamp in the middle of a call |
|
GUI process
can lock up when receiving XML messages |
|
phone
unregisters when making toll free and long distance calls |
|
7921 Reboots
with race condition between HTTP and SCCP |
|
7921 queues
SCCP reset when not in main idle screen |
|
7921 sends
SCCP Unregister message unexpectedly |
|
Corporate
Directory blanket search does not display all results |
|
7921 sources
RTP from random port rather than port specified in olc |
|
7921G phone
cannot access Corporate Directory |
|
7921 roaming
improvements |
|
7921 does not
place the softkeys in the specified order |
|
7921 does not
dial * or the # before the dial strings |
|
7921 does not
dial out on available line if shared line 1 is in use |
|
Ver 1.0(4)
incorrectly display softkey Login, Flash, Acct used by CME |
|
7921 phones
will register max 2 lines when in srst mode |
|
7921 uses
EAP-FAST vs LEAP when in AKM mode and set for CCKM only |
|
7921G error
on activating SSID with 20+ chars |
|
Speaker Phone
Activates when Phone Answered |
|
7921 fallback
failure from SRST to CUCM . |
|
7921 only
roams on max TX retries with APs not supporting QBSS |
|
7921 loses
localized tones after reset |
4.1-Devpack
66 |
|
Adding 8.3(3)Sr2 to all CUCM builds . |
|
7911 LCD
glimmer / flicker when florescent light is on |
4.1-Devpack
65 |
|
Adding 8.3(3)Sr2 to all CUCM builds . |
|
Removing
eHook feature from 11/06, 31, 41/61 and 70/71 phone models |
|
Ehook- CCM
Feature Description uses "Ehook" term . |
|
7985 |
|
When
registering to TFTP server the Call Manager Config is incorrect |
|
Toggle Alpha
Transparency of Menus using full screen key with 3 states |
|
On CME, 7985
took ~7 sec to close video chann if CUTA press Hold |
|
Mobility cell
pickup feature is not supported on 7985 |
|
Status line
is not updated when Call Forward All is performed |
|
Unable to
activate callback from 1st line to 2nd line which is shared DN |
|
7985- Hit
redial after call from 2nd line & CB, call goes out of 1st lin |
|
7985- Phone
restarts during active call if nw settings changed & saved. |
|
7985-
Transfer from Line1 to Line2 on 7985 doesnt work. |
|
7985- ringer stops when callback hit in a scenario. |
|
7985 phone
doesnt display meetme number in a meetme conference. |
|
Services
button not working when DNS returns wrong address for CM5.x |
|
7985-
Displays "From Unknown Number" on shared line, when call placed. |
|
7985 -
dialled digits are dropped, dialing from Directory in a scenario |
|
7985-
Dialling from directory doesnt initiate newcall in a scenario. |
|
7985- nw config locked, still erase button accessible in a
scenario. |
|
7985- gap
before first speed dial |
|
7985- Wrong
softkey template is retained |
|
7985- G729
codec time lag is too long. |
|
7985-No PC
port connectivity when phone is in voice vlan |
|
7985 does not
acknowledge reset message |
|
7985 does not
failback when secondary CME is not available |
|
7985 does not
support video bit rates of less than 64kbps |
|
7985 Can not
disable advertisement of g.722 codec |
|
7985- should
be able to handle audio only conference (testing only) |
|
7985- changes
to reflect Cisco Callmanager product name change |
|
Phone uses
old Alt tftp ip instead of existing. |
|
7985- **#**
to unlock needs to key-in very fast. |
|
7985- Phone
reboots on invoking graphicMenuBoundary test. . |
4.1-Devpack
64 |
|
Removing
eHook feature from 11/06, 31, 41/61 and 70/71 phone models |
|
Update
Load_ID.prm for 7937 phone |
|
Check in
Guinness phone firmware to CallManager |
4.1-Devpack
63 |
|
Adding TNP
8.3(3) and 7937 1.0(1) to CUCM |
4.1-Devpack
62 |
|
Adding TNP
8.3(3) and 7937 1.0(1) to CUCM |
4.1-Devpack
61 |
|
Adding TNP
8.3(3) and 7937 1.0(1) to CUCM |
|
Adding 8.3(3)
features |
4.1-Devpack
60 |
|
7985 Can not
disable advertisement of g.722 codec |
4.1-Devpack
59 |
|
Extra button
templates are displayed for 7937 |
|
Update the
QED setting for the 7937 phone guide |
|
User Guide
added for new IP Phone 7937 |
|
7921 |
|
High
multicast can impact battery life |
|
Proxy URL is
not supported |
|
Can not reset
phone when idle url is active |
|
7921 cannot
resume shared line hold calls beyond the first |
|
7921 doesn't
show missed calls when keypad is locked and LCD went off |
|
No audio if
source reset RTP timestamp in the middle of a call |
|
7921 enters
speakerphone mode after call park retrieval with CME |
|
Current
volume can get impacted while configuring other volumes |
|
7921 with CME
speed dial can corrupt system message display |
|
headset mic
audio may distort if in noisy environment |
|
DnD does not
work with CME on 7921 |
|
Get a 10
second audio gap after receiving deauth with static WEP128 |
|
Alert tone
does not always play when pushed via Play URI |
|
CM-6608 CFB/MTP |
|
KeepAlive
interval with CM-6608 CFB/MTP resources |
4.1-Devpack
58 |
|
Update
English locale Files into the CCM branches for 8.3.3 release |
|
Locale
Changes |
4.1-Devpack
57.1 |
|
7940 - 7960
Do not upgrade to P00308000700 |
4.1-Devpack
57 |
|
7942/7945/7962/ |
|
7965/7975 |
|
Check in
Guinness phone firmware to CallManager |
|
6608 |
|
6608 T1
resets due to bugtrap |
4.1-Devpack
56 |
|
re-tag XML
file for guinness QED |
|
7940/7960 |
|
multiple
issue after upgrade to 3.3.5sr2b |
|
Hold call is
disconnected when primary CallManager gets back |
|
7906/7911/7941/ |
|
7961/7970/7971 |
|
New Default
Background Image Required |
|
Jake
Featurette check-in |
|
7970-
Malformed UDP packet DOS attack causes phone to freeze |
|
Cloudraker-XML
Parser- xml parse error on event ID of Redirect Softkey |
|
Cloudraker-SendDigits
URI fails to send in-band dtmf |
|
Wideband
Handset available for config on 7931. |
|
7945/65/75 bounce
link on soft reset for both PC and network ports |
|
disable audio
output during bootup |
|
Alien
crosstalk is degraded after CSCsh75383 is fixed |
|
7971 DHCP
address from data vlan |
|
Hearing Aid
Compatibility tests failed on Guinness/Wideworld TNP |
|
New Default
Background Image Required |
|
Cloudraker-
Missing support of IconIndex in Title element |
|
Hebrew chars
position too high in softkeys |
|
Guinness-
nmap TCP connect scan crashes 7945 and 7975 |
|
Turbo/Goped
sometimes experienced resets after power recycle |
|
75 phone call
numbers over flows the spaces assigned for it |
|
7945/65
becomes inactive after CCM down |
|
DSP process
dies while running the call features automation script |
|
Recording
tone plays abnormally during a call |
|
7961 crashed
when running Codenomicon https suite(Test #9) |
|
DC bias
introduced by noise reduction |
|
Cannot answer
call by going off-hook |
|
call on
sharedline lost on phone - both users hit endcall on other line |
|
Update
diagnostics in BN2 for 7931 |
|
Include
Kernel.core into the sylog files for debug purpose |
|
Ph not
register afte XML Parser Excep seen during config file parsing |
|
Cloudraker-phone
fails to come up if deleted and tries to Auto-reg SIP |
|
Turbo
Bootloader Changes |
|
7962 does not
come up with load 8-3-1-10 |
|
7911 phone
crash when switching to Arabic locale |
|
797X- Phone
DHCP config data got corrupted during firmware upgarde |
|
Phone
Directory gives incorrect details after upgrade to 8.2.2 |
|
TNP Phone Update
needed for New Zealand DST changes in 2007 |
|
CIA 1085-
lower Voice Mail status line to below DND state. |
|
TNP Phone use
Narrowband Vol Table even for WB |
|
wrongly uses
tftp server as log server |
|
Broadcom
phones unable to determine source port of unicast 802.1x EAPOL |
|
Rings
shouldn't be configured for intercom lines |
|
CallBubbleSelected.png
is one pixel too wide for beamish |
|
Ph in stuck
state after capfList config structure change in SEP MAC file |
|
Ph got stuck
in Settings screen when Settings is pressed while dialing |
|
7970 RLR is
softer |
|
Phone API
startMedia request, parameter "receiveVolume" not working. |
|
7975G
characters look fuzzy/not formed correctly |
|
7962/42 advertises PAUSE capable via Ethernet AUTO-NEG |
|
Pixels
sourounding the active UI tab are not black |
|
Callback
Message screen mixed up with Placed call screen |
|
7970 plays
loud comfortable noise when using G.729 codec |
|
Phone sends
different help ID for intercom line |
|
Cloudraker-
XML parser- Hardened Soft Key Files schema rules |
|
Speed Dials
not working on SIP Phones in a specific scenario |
|
TNP sempahore
traverse |
|
Resource
Image updates for FCS |
|
Update
Guinness BN2 for Memory Bist tests |
|
Darker
greyscale images cause unreadable display on 7961/41 |
|
Guinness
handsfree mic signal can clip |
|
Cloudraker-
XML Parser- No Error when tag is duplicated |
|
Update
Guinness BN2 files with diags version 13.2.0.60 |
|
Guinness
Phones do not respond to 802.1x Re-authentication Requests |
|
Missed call
history incorrect for forwarded calls |
|
Underworld -
XML Parser Code changes |
|
Underworld-
Phone does not shows "bad ring list" for erroneous ring file |
|
Cloudraker-
XSI- xml push onFocusGained to phone executes 3 times |
|
SBB/SBCB
& Barge/cBarge call instance focus incorrect after phone reset |
|
Update
Guinness mfg image to include new diagnostics ver 13.2.0.49 |
|
PS loads
fails to switchover to Jap locale |
|
Resource
Image updates for FCS |
|
Underworld-
Config File schema errors and issues |
|
XML Schema
hardening prevent encrypted & non-encrypted config parsing |
|
7970 with
firmware 8.2.2sr1 speaker not working correctly |
|
7962- packets egressing PC port should have PC vlan untagged. |
|
New
generation phone have lower volume then older phone types |
|
Null pointer
exception on XML Parsing for SIP phones |
|
3rd phones
break 802.1x auth when span to pc enabled |
|
ESW clock not
initialized properly by boot loader |
|
7962 barge in
no voice |
|
XML data
can't be rendered to IPphone |
|
Guinness
Handset RLR incorrect |
|
AEC
suppression can degrade voice quality scores on Guinness |
|
Guinness-
Color models are displaying visual noise on power cycle/reboot |
|
Pixels
surrounding the active tab are not black |
|
Cloudraker-
CFWDALL and MCID not working on SIP phones |
|
TNP SIP phone
can not failover to SRST due to wrong port |
|
Start Media
Response does not returns codec string correctly |
|
Guinnes
handset - "highs" are little too high |
|
Goped
Bootloader Changes |
|
New XML
parser unable to display another Ph web page in XML services |
|
Audioble MWI
(Stutter Tone) is not sounds correct |
|
TNP phone
corrupt background image causes blue image and crash |
|
Turbo-
Malformed UDP packet DOS attack causes phone to freeze |
|
Broadcast
Storm one way audio for 7961 SIP |
|
Update
diagnostics in BN2 for 7911 / 7906 |
|
Volume
Control on Group Listen is Broken |
|
Guinness-
Malformed UDP packet DOS attack causes phone to freeze |
|
7945/65/75
Hardware version 6.0+ uses external gamma |
|
7970- nmap
TCP connect scan crashes 7945 and 7975 |
|
Analog codec
audio output enabled in early stage |
|
802.1x
packets are not forwarded |
|
SBB feature
does not work |
|
Update
Guinness BN2 mfg image to release signed |
|
Need a
smaller font for the call reference for Makaha and Caffreys. |
|
Calls
transitioning to OFFHOOK state should take focus |
|
send specific
XMLobject code into 7970, phone cannt request EM service |
|
Guinness-
improve AEC doubletalk performance |
|
TNP SCCP ph
unable to come up and register with sidecar 7914 attached |
|
Underworld -
XSI Backward Compatibility Changes |
|
SDK version
updated to 6.0.2 for 8.3.1.release branch [8.3(2)] |
|
when
callwaiting tone is invoked, calls stop getting ringback |
|
support new
Spansion flash part |
|
OS PLL init
setting unnecessary |
|
Resource
Image updates for FCS |
|
Bogus load
name in Phone load element value cause TNP phone to hang |
|
3rd gen phone
may loose personalization after rereg to another CCM |
|
831-Settings
button access set to restricted disables directories/servic |
|
Phone will
not load from case sensitive TFTP server |
|
Bug in
vFillShorts assembly source |
4.1-Devpack
55 |
|
Enable
Guinness Model phones to appear in CUCM Admin Pages |
4.1-Devpack
54 |
|
Phone does
not display full status message when registration fails |
|
7906/11
display square symbol when the Caller ID too long. |
|
Update Device
Support |
|
7940/7960 |
|
7940 / 7960
reboots when receiving IP fragmented packet |
|
7940/7960
phones fail to upgrade LSC with CME secure authentication |
|
Choppy
audio/jitter in incoming RTP to 7960 causes one way audio |
|
no audio
after high delay or jitter on network with g.729 |
|
hook switch
debounce timer too short on 7940 IP phone |
|
In
speakerphone disabled state, 'Dial' softkey active in a scenario |
|
when
callwaiting tone is invoked, calls stop getting ringback |
|
7960(sccp)
resets under Codenomicon HTTP test suite running |
|
7960/SCCP
resets under two cases of Codenomicon TCP Test suites |
|
7960/40
ignores StartTone Messages when in connected state |
|
Phone struck
in a loop inside the personal address book |
|
Migrate to
use new load authentication key |
4.1-Devpack
53 |
|
Adding 8.3(1)
Display instances to all released CCM branches |
|
7935,7936 |
|
Phonebook
doesn't display numeric number by default in Web interface |
|
Second phone
in a shared line hangs in a failback and failover scenario |
|
Phones hangs
while using restore default from UI in this scenario |
|
Phone UI
displays error when Restore Factory default in a active call |
|
Fields in
"Add New Phone Book entry" in 7936 GUI do not get refreshed |
|
"Server
error-413 N/A" appears when wrong input given in phone book |
|
Phone book
entries duplicate |
|
No validation
for "upload logs" under Diagnostics in phone menu |
|
|
|
No. of
characetrs as password input inconsistent in GUI and phone menu |
|
Call Park
Reversion message not displayed |
|
|
|
Network
settings dont work when 2 phones are in a call |
|
Phone Book
does not accept 24 digits as DN |
|
Only 23
digits displayed of a 24 digit DN though lot of space available |
|
Softkey
templates working improperly |
|
CFwdAll in an
active call breaks the voice path |
|
CP-7936
v3.3.11 can continually reboot after a few weeks on HP switch |
|
7936 may not
dial the * character when using Phone Book |
|
Softkeys
missing(7936) ,when huntpilot call is answered with callfwdall |
|
Phone plays
ringback tone if destination phone has CFA set to unknown. |
|
Deleting the
DN freezes the phone |
|
"Http
Server" label in place of Http client |
|
DN does not
display completely |
|
Reboot does
not work |
|
Pressing
menu-> phone button in active call phione in a wierd state |
|
c in click
should be capital on "Passwords/HTTP Port Change" webpage |
|
Help page
does not show hostname |
|
Changing the
ringer during an active call puts the phone on hold |
|
Help page of
time and date does not list all the date options |
|
The heading
for Password page in GUI should be different |
|
Help Page of
Network Setup incomplete |
|
Softkey
templates incorrect in case of Shared line |
|
7936 phones
intermittently fails to upgrade to new load |
|
Icelandic
characters not shown on 7936 IP conference phone |
|
Spelling of
transfer softkey in case of new call |
|
CFwdAll
softkey is absent when initiating a new call during active call |
|
7936 DN
display only displays 11 digits of a 12 digit DN |
|
7936 -
tone49(zipzip) has beep beep then sounds like long euro ringback |
|
CP7936
Experiencing Possible ARP Cache Corruption |
|
7936-
conference soft keys becomes inactive after a few calls |
|
Need support
for GetElementManagementFromManagedElementOid |
|
7935 &
7936 stops after 8dhcp discoveries w/no response |
|
DHCP changes
can cause phone to reset while on a call |
|
7936 resets
or one-way audio due to exceptions caused by DHCP renewal |
|
7906G,7911,7941,7941GE, |
|
NullPointer
Exception on AutoCallAgentImpl.inFocusItemChanged() events |
|
DSP
Configuration Files are not Correct |
|
7911 DEV load
contains incorrect jar file |
|
Third-Gen
SCCP Retries Registration 20K+ Times/Day On Phone-Reg-Rej |
|
R2D-
mapPixelCoordinatesToWindow always returns NULL. |
|
Pressing New
Call should let user "Enter Number" |
|
M&R- new
M&R tone command should override playing tone of same type |
|
Tone not
suppose to send to supervisor when selected remote only |
|
Phone does
not show complete information for show inventory command |
|
Change the
immDiv softkey name to Redirect - Update SIP dictionary files |
|
Need
Automation API to get status of headset, mute and speaker lights |
|
Commit of
CSCef34402 broke c6slc, other? pikespeak images |
|
make 'DEBUG'
trace anticipated for a 1-way audio problem as NOTICE trace |
|
Phone doesn't
calculate SRTP auth tag correct for certain RTP payload |
|
DC bias
introduced by noise reduction |
|
Play URI
doesn't play ring file after first time push |
|
Guinness-
Continuous unicast traffic resets the phone |
|
C-P-7941
Changes on the Ring Tone go back to Default after a soft reset |
|
Update memory
timings for Goped boot loader |
|
SIP phone
failed to clear Held call when CCM restarted |
|
TNP- keyboard
I/O errors on reset |
|
No spkrphone
dialtone when Trans/Conf button hit on TNP SCCP 8.3.0.9S |
|
ppid found
file system issue with unmount beneath stdio file access |
|
Re-partition
MIPS memory allocated for ZSP |
|
G.722
K-Factor Table incorrect |
|
Call duration
timer window on ph display cycles between multiple calls |
|
7971-ringer
volume is too high |
|
7971 unable
to come up while detecting Supplicant on both switch port |
|
Guinness-
Beamish models should not have touchscreen enable/disable |
|
7942/7962-
pressing "Cancel" key does not discard change to contrast |
|
Stutter Tone
quality problem when using speaker / line button |
|
797X- Phone
DHCP config data got corrupted during firmware upgarde |
|
Phone UI
locked up when remaining in fail over mode |
|
minimum send
gain not consistent |
|
Static
analysis on debug shell |
|
Broadcom
phones unable to determine source port of unicast 802.1x EAPOL |
|
CallBubbleSelected.png
is one pixel too wide for beamish |
|
Add wideband
PLC to codec G.722 and L16K pcm |
|
7931-
Pressing Line button does not change Line focus |
|
7975 Gigabit
is sensitive to CM signal, and loose many packets |
|
Show wrong
time when using the |
|
Change dsp
cost table for iLBC |
|
Noise
reduction causes highband rolloff on handset |
|
7931-
Overview not in home position at initial bootup |
|
Speed Dials
not working on SIP Phones in a specific scenario |
|
DSP resets
when Noise Reduction is enabled and spike in audio signal |
|
keypad tones
not played on speakerphone when transfering a call |
|
RTCP socket
open error may cause audioserver to spin |
|
Fix Static
Analysis warnings from TNP security code |
|
EAP-Request/MD5
to PC supplicant could not pass thru Gig phone |
|
GoPed- Auto Line
Select does not work as expected |
|
IP-phones
hang when call arrives while XML-play in progress |
|
Phone hangs
if it stays on placed calls when the peer ends the call |
|
Third gen
phone may behave wrong under stress registration test |
|
Guinness- PC
port does not forward egress packets |
|
SIP Phone
core dumped after failover |
|
Disable
Speaker/Handset for TNP SIP doesn't disable Meet me Softkey. |
|
echo on
guinness speakerphone |
|
7970 with
firmware 8.2.2sr1 speaker not working correctly |
|
Unusable G711 calls (loud noise) |
|
Automation-
Need enhancement to AutoStream for SRTP or RTP |
|
Automation
does not work on 7911 |
|
need
interface getLineButtonPosition() to AutoCallAgentIf |
|
Phone- Dial
softkey should not be available for PRIVATE numbers |
|
CallHistory
Menu- line key, speaker key, no longer work |
|
Remove tftp
command from Mirzam ROMMON |
|
7971/7941
re-append parameters with a redirected authentication |
|
CDP can alter
statically assigned VLAN |
|
R2d code
doesn't return null reference for corrupted PNG file |
|
TNP SCCP
phone displays "???" for DND linekey |
|
Remove I-Hold
changes for |
|
3g-phones --
pick up Sun Java patch to address 2007 DST changes |
|
TNP SIP phone
needs to be power reset to re-register in a scenario |
|
slower error
propagation causing ph to become leaf of grand child phone |
|
7971 Shows
NPE when rebooted during inactive time |
|
Incorrect DSP
Configuration File Formats |
|
7911/7931/7962-
DSP process memory leak |
|
Filesystem
Privilege Escalation |
|
Volume
Control on Group Listen is Broken |
|
When zrun
exec VM, it returns immediately& unmount takes causing Ph loop |
|
ppid display
notification icon addition |
|
Psylocke code
review |
|
SCCP70.MU-1-0-19S
advertises iLBC and causes the call drop |
|
7931-
Softkeys not Updated in |
|
PPID- sunvm
should not be trying to come up while /dnld is occupied |
|
Noise
Reduction voice metric has erroneous value |
|
Guinness-
Update LCD device driver for 7975 (Murphys) model |
|
supposed lock
issue on CNU rebooting contention problem with init |
|
SA errors for
activate() methods |
|
AutoStream
getRemotePort returns neg value for ports in 60000 range |
|
Guinness-
Psylocke SOC SA/Cleanup |
|
Inconsistent
display of DND Feature (in line button) on SIP & SCCP Phone |
|
KA timer
still alive on child phone; phone creating new tranfer process |
|
Audible MWI
support |
|
authentication
fail on parent, but child authenticates OK |
|
Guinness-
keypad device driver for 7945 / 7965 models (Beamish) |
|
SA baselining
for TNP |
|
7931-Resume
SK does not resume call after scrolling to another line |
|
Merge from
DSP Version 4.2 |
|
Phone goes
out of memory after upgrade/downgrade due to OutOfMemoryError |
|
Hearing Aid
Compatibility tests failed on Guinness/Wideworld TNP |
|
Hebrew chars
position too high in softkeys |
|
Comfort Noise
needs to be tuned for Wideband codecs |
|
8.3(1) SCCP
Phone resets during video setup with non-CM6.0 Endpoint |
|
Display scr.
is dark & won't accept input while phone upgarde downgarde |
|
phone as root
and leaf for the same file; two roots for the same file |
|
Phone with
network plugged into PC port can get stuck if link drops |
|
Osage- Phone
drops incoming unicast EAPOL when VVLAN is present |
|
Customer
cannot use Codec of their choice after 8.2 phone load install |
|
Parent not
sending KA to leaf; leaf reroot; end up with TLOAD |
|
Phones
failover to secondary node with wrong cause code |
|
PAE can't
exit due to a file lock during shutdown, phone hangs |
|
Cannot answer
call by going off-hook |
|
call on
sharedline lost on phone - both users hit endcall on other line |
|
TNP phones on
CME can't resume call with Line button |
|
Focus does
not shift to off-hook line while another call is incoming |
|
PPID FOUND
CORNER CASE- init never reimages in certain instance |
|
Include
Kernel.core into the sylog files for debug purpose |
|
Focus should
remain on oldest ringing call with mulitple incoming calls |
|
set ringtone
after preview ringtone can crash a 3rd gen phone |
|
NAK SMT/ORC |
|
7975 Network
Stats page displays the wrong NW port info |
|
Guinness-
move interrupt learning code to a helper function |
|
MenuApp
Application has wrong icon in title bar |
|
Merge Noise
Reduction improvements into Mainline branch |
|
Phone
Directory gives incorrect details after upgrade to 8.2.2 |
|
Muster- Phone
Errors when pushing URL's with priority |
|
offhook w/
handset for the first time after reboot, no dialtone is heard |
|
Filesystem
Denial of Service |
|
7962/42 advertises PAUSE capable via Ethernet AUTO-NEG |
|
PPID Unit
Test Findings - TCP Communication Problem on Root Removal |
|
SIP phones
run out of memory in Java heap for every call |
|
XML Parse
error when phone is dialing |
|
7911/7972-
Add tool to dump DSP data structures, initially msg buffers |
|
Remove
redundant model specific dictionary entries |
|
Update boot
loader on Guinness phones |
|
Replace TI
assert function by dspfw define ASSERT |
|
No dialtone
with handset off-hook or using the Speaker button |
|
Change text
on Power Save Config menu of phone from Display to Backlight |
|
Guinness- Update
Touchscreen device driver for 7975 (Murphys) model |
|
Guinness-
update LED test app for 7975 model |
|
SBB/SBCB
& Barge/cBarge call instance focus incorrect after phone reset |
|
OnHook
Dialing from Line2 doesn't work if Line1 and Line2 have same DN |
|
Not able to
configure Directed Call park BLF in 7970/71 SIP phones. |
|
GoPed- Add
Help for Fixed Feature Keys, NavPad, and LocalFeature PLKs |
|
Graphic
Issues |
|
guinness
audio improvements |
|
Guinness- use
port index to update queue link speed |
|
TNP phones
fail to upgrade LSC with CME secure authentication |
|
Enhance
kernel memory utilities to report free blocks in the virtual mem |
|
7970/71/41/61-
DSPBOOTStart-Sync failure btw ZSP and MIPS-MBOX1=DEAD |
|
Need ability
to send hook signal for onhook transfer feature |
|
Phone does
not come back up when the PC and sw cables are reversed and r |
|
new threaded
PPID algorithm with dual TX threads wont shutdown |
|
"Update"
softkey isn't displayed when focus is on LSC |
|
Turbo-
Malformed UDP packet DOS attack causes phone to freeze |
|
Phones don't
handle fatal Java exception properly |
|
IP phone
fails to parse the encrypted config file |
|
SIP Tnp
Phones display needs to be changed |
|
bug trap 91
on system reboot |
|
Don't write
cdp.conf file everytime we recieve packet if not necessary |
|
Changes per
UI Evaluation |
|
clean up
syslogs in PPID remote and console logging |
|
differentiate
illegalStateException in getNodeId() |
|
No help
information avail for NAV Left NAV Right button in 797X phones |
|
IDLE Phone
with Open detailview screen cause inconsistant DTMF behaviour |
|
CallHistory
Menu- Going offhook dials wrong number in special case |
|
With Setting
Access to restricted can access Network Config |
|
Phone gets
stuck while resetting |
|
SIP 7970
phones showing RemoteHeld state while it has to be in HELD stat |
|
/usr/cache
out of space - can't create a new file |
|
7961 phone
not show Help info for privacy button |
|
Large
increase in PNG graphic processing time |
|
Focus should
remain on oldest ringing call with mulitple incoming calls |
|
Wideband
Handset available for config on 7931. |
|
Handset
adaptive gain control needs to match the 7940/7960 |
|
Automation-
Need isSelected method in autoobjinfocus |
|
Display Timer
on TNP Phones wrong, Meet Me initiated with Trans
Pattern. |
|
Shared memory
access collision between dspfw and driver |
|
JPN- Cannot
Display Kanji via UserToDeviceData |
|
Bug trap 91
if TCP server/client resides in the phone |
|
79x1 phone
delay to display system message after deactivate DND |
|
Leave space
between display of Internal caller ID and Line Text Label |
|
Guinness-
create unique queue for reserved mcast |
|
turn on WB
handset feature bit in mfgInfo for guinness phones |
|
Background
Image list item irregularities |
|
Intercom-
7931 phone cannot complete onhook dialing with incoming interc |
|
Takes long
time to receive error from phone |
|
SIP phone
stop registering to CCM w/ 50% packets loss |
|
Unknown name
displayed if special characters are in display name |
|
dtmf issue in
CME software conference |
|
7911 Ph
unregister flood console logs with Supplicant logged off message |
|
Top of
Softkey Graphics Disappears When Slider Bar is Shown |
|
Add debugging
info-- add brodcast TX/RX count to call trace |
|
phones should
keep the latest Kfactor value in the phone stats |
|
7914
configured over 15 digit in line number behaves very strange |
|
Guiness 7945s
got stuck during ppid upgrade |
|
some SCCP
phone types does not play call alert or reminder tone for DND |
|
CallInfo page
displays wrong status for the idle lines |
|
convert
"Can Not" to "Cannot" in all SCCP english dictionary phrases |
|
SIP7911 stuck
during automated upgrade/downgrade |
|
Guinness-
Update BN2 to latest diagnostics version 13.2.0.33 |
|
AutoFeatureIf
invokeDirect returns success when softkey press failed |
|
Headset LED
in wrong state after power cycle |
|
CallHistory
Menu- Can't dial with line key|speaker in special cases |
|
Guinness-
update to latest diags for all guinness phone models |
|
Privileged
Shell Commands available to unprivileged user |
|
Handle REG
ALL FAILED differently to allow LSC installation |
|
Root phone
not offerring new leaf when its children are gone |
|
AutoObjInFocusIf.getLabel
returns incorrect information for a call item |
|
7975/45/65-
Gig E speed option unavailable Switch port or PC Port settin |
|
Guinness
bugtrap- SY MSG- Kernel Shu= 0x6666 |
|
Call
Preservation- sccp to sccp intercom call clearing issues |
|
mislist
processing removes critical files on upgrade [stale file problem |
|
Need to be
able to get the versionStamp for the config |
|
Intercom-
phone does not do talkback if onhook dialing is in progress |
|
ESP debug
message add ( |
|
Guinness-
Implement Psylocke programming restrictions |
|
on speaker,
noise or mute tone heard when pressing Mute button |
|
Factory Reset
require for secure phone to move to another CCM |
|
3rd phones
break 802.1x auth when span to pc enabled |
|
Bugtrap 0x91
phones (during fsck) |
|
phone load
need to support new timezones |
|
Guinness-
provide register access for gig testing |
|
2nd iLBC
channel can't be opened as full-duplex to do barge-in |
|
Collapse
muster into tnp_main branch |
|
third gen
phones power is initally set high power at boot w/line powered |
|
Phone web
page http-//Phone IP Add shows ??? character for
parameter nam |
|
Update 7975 /
7965 / 7945 bootloader for LED changes in new HW |
|
Pre-dial list
shows DN followed by conference after a conference. |
|
flash/buffer
comparison failing |
|
Repeated
Dialing from Call History Menus causes OutOfMemoryError |
|
CallInfo URL
missing VisibleFeatureList tag when application pane open |
|
Secure
conference need support for getting icons from confList |
|
7975- Add
touch panel calibration defaults |
|
Phone
declared as a child twice by same parent due to keep alives TO |
|
SIP Intercom
- enable redial feature |
|
Audioble MWI
(Stutter Tone) is not sounds correct |
|
Time zone
rules do not update correctly on 3rd-gen phones |
|
7911 phone
advertise 2 iLBC codec on its capability message |
|
dhcp memory
leak |
|
Change dsp
cost table for G.722 |
|
7941/61 TNP
time displays 1 hour early if power cycle |
|
Guinness-
Malformed UDP packet DOS attack causes phone to freeze |
|
Internal
calls are having one way audio |
|
802.1x
packets are not forwarded |
|
Need a
smaller font for the call reference for Makaha and Caffreys. |
|
Private RIU
calls show up in the callinfo list |
|
IP Phone SSH
Vulnerability |
|
Read
linenumber from the config file |
|
Noise
Reduction total energy parameter rests at 28 instead of 0 |
|
7970 phone in
low power mode consumes more power than CDP advertisement |
|
SenderJoins
& Byes values were different regardless of call status |
|
Bogus load
name in Phone load element value cause TNP phone to hang |
|
Phone TFTP
request packet for a background image is Malformed Packet |
|
guinness-
code cleanup in dsp device driver |
|
Guinness-
Update diags for Murphys to 13.2.0.23 |
|
TNP Phone SSH
Vulnerability |
|
Update
diagnostics / BN2 for guinness phones |
|
XML parsing
error on LineInfo to turbo phones w/ speed dial configured |
|
MenuApp
Application has wrong icon in title bar |
|
7970-
Malformed UDP packet DOS attack causes phone to freeze |
|
SIP shows
incorrect info for placed intercom call in IntercomHistory log |
|
SIP phone
should disable Callback and DND for intercom call |
|
port
"reset on sleep mode" ddts to guinness code base |
|
Modify
assembly to address Titan Advisory R5691 and c55 Advisory CPU_116 |
|
Multiple
softkeys on the phones are "bleached" on touchscreen drag |
|
Need
automation API to get tthe time/date from the phone |
|
Update cpk
files for Beamish model 7965 phone |
|
Need to Press
Right button twice on Nav Pad to close Line Detail |
|
Guinness-
nmap TCP connect scan crashes 7945 and 7975 |
|
Composed IPPM
messages display + instead of space |
|
Update power
requirements for 7945, 7965, and 7975 phones |
|
Guinness-
Update BN2 to latest diagnostics version 13.2.0.31 |
|
75 phone call
numbers over flows the spaces assigned for it |
|
Recording
tone plays abnormally during a call |
|
DSP process
dies while running the call features automation script |
|
LCD for
Guinness 7975 need color register adjustment |
|
SIP 7911 and
7961- Erase config from Settings menu does not reset phone |
|
Font kerning
issue on 7970 |
|
Missing
Pixels on the left side of UI displays on Turbo phones |
|
Guinness
phones need different EQ based on Handset Hookswitch |
|
Phone does
not get registered when daisy-chained with 7961 phone |
|
Customer is
experiencing one way audio calls |
|
TNP
improvements- /bin/sh should always be a POSIX-compliant shell |
|
7971GE- Sleep
Mode issue |
|
7941 - BLF
speed-dial status LED does not work |
|
PNG Broken-
Phone fails HTTP GET if earlier HTTP request is not finished |
|
wrongly uses
tftp server as log server |
|
Rings shouldn't
be configured for intercom lines |
|
SIP phone
does not answer by lifting handset |
|
LCD for
Guinness 7975 phone displaying inaccurate color balance |
|
Phone sends
different help ID for intercom line |
|
TNP sempahore
traverse |
|
Shared line
display & going offhook while in active call distort display |
|
command parse
error and command search fail on 7970 |
|
JAL doesn't
work as per requirement with c-Barge Conference |
|
Frequency
Value for Steady Dial Tone After Stutter is Wrong |
|
PPID Unit
Test Findings hash test ugliness |
|
Jphone and
init.tab and sleep interaction |
|
Update
diagnostics for Guinness phones to version 13.2.0.36 |
|
Phone does
not get registered when daisy chained |
|
pressline 2
not working for 2nd line of 7941 |
|
SCCP phone
does not register back to publisher after restart. |
|
GUI stuck
after changing contrast |
|
SA for
img_main (image daemon) |
|
Enhancement- provide an indication of when flash was last formatted. |
|
Guinness- Fix
the printing of the Chip Version Register (CVR) values |
|
Ph hits max
file download timer of 60 min during firmware upgrade downgr |
|
TNP Phone
7941 second line line button will light up for incoming call. |
|
SIP phone
init a new call when pressing the line that already has a call |
|
Hung RS-232 port causes phone upgrade failure |
|
Response.Redirect
fails |
|
When ph is
going to safe mode or TLOAD its background should be cleared |
|
Ph stuck in
IDLE state after Java Error without CallManager menu Entry |
|
7945/65/75
Hardware version 6.0+ uses external gamma |
|
7970- nmap
TCP connect scan crashes 7945 and 7975 |
|
7975- PC port
goes no link after reconfiguring to 1000F |
|
G722
Monitoring call could not be setup for iLBC primary call |
|
Memory Leak
on phones with repeated calls with very short call hold time |
|
Calls
transitioning to OFFHOOK state should take focus |
|
Event needed
for reset |
|
Change the
CiscoError, CiscoStart and CiscoReboot png files for new logo |
|
Phone core
dump while running the call features automation script |
|
7971
SIP/SCCP- PC port can be enabled after being disabled from CCM page |
|
|
|
Idle sftkeys
displayed on new incoming call after transferw/rel image |
|
Erroneous
Behavior when DialLine URI on Intercom Line that has call |
|
Gross timeout
for downloading file with DLOAD & TLOAD should be changed |
|
when
callwaiting tone is invoked, calls stop getting ringback |
|
Host unicast
traffic are not forwarded to the egress PC port |
|
support new
Spansion flash part |
|
GoPed-
localization work for Muster |
|
Phone hangs
while downloading PNG files |
|
7970-
implement ethARLCache functions |
|
TLoad-
timer_start fail - doGrossTimeout-serial issue seen on 16s load |
|
831-Settings
button access set to restricted disables directories/servic |
|
Callback
softkey is presented but it doesn't do anything. |
4.1-Devpack
52 |
|
Locale file -
target-dictionary.utf8.xml needs to be updated |
4.1-Devpack
51 |
|
7920 |
|
7920 Firmware
3.0.2 Check-in |
4.1-Devpack
50 |
|
Need a way to
control SSH access to phone from CM |
|
Check-in
Cisco 7921 firmware version 1.0(3) to CallManager |
|
Special
number call is cancelled after 1 ring when keypad is locked |
|
Phone on Antiope
vibrates if headset attached when set vibrate alert |
|
User can not
do factory reset if setting access is disabled |
|
High
multicast can degrade unicast RTP voice quality |
|
75% battery
icon appears with full battery |
|
7921 doesn't
work with CME unicast paging |
|
Power
consumption high after roaming during a call with tspec enabled. |
4.1-Devpack
49 |
|
7937-Device
Definition Files Need to be Checked In |
4.1-Devpack
48 |
|
7937-Device
Definition Files Need to be Checked In |
|
7985 |
|
7985 Screen
Powersave LED indicator can't be distinguished from MWI |
|
7985 sources
from random port rather than from standard specified in olc |
|
7985 should
use symmetrical UDP port numbers |
|
Visual call
Pickup notification fails when line audio alert setting off |
|
Visual Pickup
Notification sometimes does not overwrite status line |
|
7985 phone
not working with Mobile Connect service. (CMM/SNR) |
|
7985 does not
send out video packets w/ IPMA configured |
|
Star50
feature is not working on 7985 video phone |
|
7985 phone
with no voice vlan configured fails DHCP/ip address. |
|
7985 enters
reboot loop on upgrade when using Alternate TFTP |
|
7985- the >> and delete softkeys in edit dial screen arent
working. |
|
7985- restart
loop if load is different between DHCP and alternate TFTP |
|
7985- Phone
crashes when long input is entered in inputboundary test. |
|
7985- Ringer
stops riniging when try to change ringer drg outgoing call |
|
Ringer stops
when 2 incoming calls on 7985 & 1 call ended. |
|
7985- Phone
dumps hex value on screen with imageboundary service test. |
|
7985- IPMA -
Manager screen goes off after every change |
|
7985-
Screensaver leaves chars all over screen |
|
|
4.1 Devpack
47 |
|
7905/7912 |
|
CP7912-UK
Locale files are downloaded every time the phone reboots |
|
7912 increase
number of digits displayed for external phone number mask |
|
DTMF Tx
failing 7912G |
|
7912G IP
PhoneCannot access corporate directory with French locale |
|
CP7905/7912
phoneDN returned Under DeviceInformationX is Incorrect |
|
7912G does
not boot up after firmware upgrade |
|
CP7912G-The
behavior after the recovery from the DHCP issue |
|
Incorrect
chunk size in http encoding for StreamingStatisticsX |
|
HTTP URL
requested by 7912 misses variable name |
|
7912-Calling
number is missing from received call history |
|
The memory
space of version string is smaller than the macro definition |
|
7912 should
retry after HTTP refresh failed |
|
7912 8.0(2)
SCCP - phone resets when accessing Corp Dir or other XML |
4.1-Devpack
46 |
|
Check in 7914
loads |
|
Add new icons
for sidecar to support Muster release |
4.1-Devpack
45 |
|
guinness -
device definition files need to be checked in |
4.1-Devpack
44 |
|
guinnessdevice
definition files need to be checked in |
4.1-Devpack
43 |
|
Adding THX
and Babylon5 features |
|
7940/7960 |
|
Animated
circle (reset icon) seen continuously in a scenario |
|
Add new icons
for sidecar to support Muster release |
|
7960 not
allow to select 2nd call of a conference call on shared line |
|
A call picked
up is not recorded in 'Received calls'. |
|
Upgrade LSC
menu strings not flushed on moving out of tht menu. |
|
7960 stops
sending CDP packets - causes do1x error disable switch port |
|
Phone remain
in Configuring IP state even with proper DHCP response |
|
Option 66
preferred over option 150 based on appearance in DHCP ack. |
|
7960/40
skinny do not detect handset with failover to SRST |
|
Unicode
Special Characters blacked out on 7940 and 7960 SCCP phones |
|
Several call
progress tones need to be louder |
|
Secure
Conferencing Icons for Muster |
|
7960 phone
does not calculate srtp authentication tag correctly |
|
Placed call
list shows '*' for FAC enabled calls |
|
Secure SCCP
Phone Conference Initiator Crashed on Hangup |
|
7940 ph does
not accept new req after rejecting invalid IP address req |
|
7960 SCCP
does not play beep tone when DND incoming alert is configured |
|
Phone
temporary rejects HTTP connection when its sockets are available |
|
Static, white
noise heard w/ 7960 7940 logging into unity with G729 |
|
Update Cisco
Logo on phone web pages |
|
Update the copyright
year to 2007 on the boot display for the mid-range |
|
7940/60 not
streaming sometimes when using encryption |
|
StreamingStatisticsX
reports phone as idle when call is active |
|
IP phone at
remote offices stuck in opening. |
4.1-Devpack
42 |
|
Checking in
latest tone file for third generation phones. |
|
6608 |
|
6608 MTP port
intermittently unregistered |
|
6608 T1 CAS
ports are getting marked as OOS |
|
6608- Cleanup
code to make room for few more fixes |
|
6608- debug
enhancements |
|
6608 Gateway
gets unregistered after resetting MGCP Backhaul port 2428 |
|
7906/11/41 |
|
Phone
Directory gives incorrect details after upgrade to 8.2.2 |
|
TNP- keyboard
I/O errors on reset |
|
7970 phone in
low power mode consumes more power than CDP advertisement |
|
Phones
failover to secondary node with wrong cause code |
|
Network
Locale Version backwards compatibility |
|
Third gen
phone may behave wrong under stress registration test |
|
3g-phones --
pick up Sun Java patch to address 2007 DST changes |
|
Hung RS-232 port causes phone upgrade failure |
|
7971/7941
re-append parameters with a redirected authentication |
|
7914
configured over 15 digit in line number behaves very strange |
|
phone UI
Locks up when adjust Speaker Volume during registration w/ BLF |
|
third gen
phones power is initally set high power at boot w/line powered |
|
3rd gen
phones running 8.0(4)SR1 unable to adjust ringer after a call |
|
u7961/41/70
stuck at requesting after phones inbound web access disabled |
|
PNG Broken-
Phone fails HTTP GET if earlier HTTP request is not finished |
|
After flash
reformat phone gets flash Programming failure errors |
|
Memory Leak
on phones with repeated calls with very short call hold time |
|
Pressing New
Call should let user Enter Number |
|
Bugtrap 0x91
phones (during fsck) |
|
Composed IPPM
messages display + instead of space |
|
Unknown name
displayed if special characters are in display name |
|
Exit softkey
stops UI when in Security Configuraiton/CTL File submenu |
|
TNP phones on
CME can't resume call with Line button |
|
make 'DEBUG'
trace anticipated for a 1-way audio problem as NOTICE trace |
|
Customer is
experiencing one way audio calls |
|
SenderJoins
& Byes values were different regardless of call status |
|
GUI stuck
after changing contrast |
|
Osage- Phone
drops incoming unicast EAPOL when VVLAN is present |
|
Call duration
timer window on ph display cycles between multiple calls |
|
Idle sftkeys
displayed on new incoming call after transferw/rel image |
|
AutoObjInFocusIf.getLabel
returns incorrect information for a call item |
|
Response.Redirect
fails |
|
Need to Press
Right button twice on Nav Pad to close Line Detail |
|
IP Phone SSH
Vulnerability |
|
Filesystem
Privilege Escalation |
|
Internal
calls are having one way audio |
|
Filesystem
Denial of Service |
|
OnHook
Dialing from Line2 doesn't work if Line1 and Line2 have same DN |
|
Phone doesn't
calculate SRTP auth tag correct for certain RTP payload |
|
Bug trap 91
if TCP server/client resides in the phone |
|
Stutter Tone
quality problem when using speaker / line button |
|
Focus does
not shift to off-hook line while another call is incoming |
|
Focus should
remain on oldest ringing call with mulitple incoming calls |
|
Factory Reset
require for secure phone to move to another CCM |
|
IP-phones
hang when call arrives while XML-play in progress |
|
Phone
displays CM down in a active call during failback |
|
Large
increase in PNG graphic processing time |
|
7961 phone
not show Help info for privacy button |
|
No dial tone
is heard after togglling the hookswitch in ring out state |
|
Read
linenumber from the config file |
|
Focus should
remain on oldest ringing call with mulitple incoming calls |
|
CallHistory
Menu- line key, speaker key, no longer work |
|
SIP Phone
goes for a reset when proxy address name starts with _ |
|
phone resets
after warning out-of-chunks for memory tracking |
|
Caller-id is
not updated correctly for conference calls |
|
Retrieving a
parked conference call, disconnects the call |
|
Phone crashed
running Codenomicon SIP test 4913 |
|
unable to do
cfwdall if kpml is enabled in sip-srst mode |
|
SIP phone
failed to clear Held call when CCM restarted |
|
call tranfer
after cfw noan on tnp sip phone failed |
|
Incorrect
Date header value in SIP REGISTER request |
|
SIP Phone
needs to also detect non-localized Conference |
|
Number stored
in missed calls not updated upon receipt of SIP UPDATE |
|
Not able to
Set CallFwdAll on tnp sip phone in particular scenario |
|
TNP SIP
sometimes sending malformed to or from header |
|
7970 sip
sends invalid presence subscription causing high CPU |
|
Failed on
multipl forward from SIP phone to SCCP phones |
|
tnpsip phone
doesn't light up blflamp when destination press callfwdall |
|
Phone crashes
when messages hard button is hit. |
|
Call not
forwarded after CTINewCallAcceptTimeOut on SIP TNP phone |
4.1-Devpack
41 |
|
7936 Phone
Displays Host not found when accessing corporate directory |
4.1-Devpack
40 |
|
Check-in
Cisco 7921 firmware version 1.0(2) to CallManager |
4.1-Devpack
39 |
|
Need to
change PTT URL to Application URL |
|
Install
unconditionally Reinitializes replication |
4.1-Devpack
38.1 |
|
Merging local
dictionary in CCM |
|
Check-in 7921
firmware to CallManager |
4.1-Devpack
37 |
|
7935/7936 |
|
7935/6 reboot
using corporate directory search on 3'rd party LDAP server |
|
7936 with CCM
5.0 displays Server Not Found when access Corporate Dir |
|
7936- Can
gain access to web interface w/o admin password |
|
7936 does not
register G.729a capability along with G.729 capability |
|
Selecting
Tone Test and exiting hangs phone |
|
Setting up
Admin VLAN id brings up the phone without a DN |
|
7936/35-
Ignore CDP V1 message for VLAN configuration purposes |
|
7936 phone
hangs when pressing hold & resume |
|
7935 does not
recover after power/network loss |
|
7936 phone
shouldn't release its VLAN until the TTL(CDP message) expired |
|
UI displays
Failed to set VLAN Idwhen changing n/w setup in activecall |
|
When we dial
the DN through web page ,message flashes for sec & proceeds |
|
7935 does not
register G.729a capability along with G.729 capability |
4.1-Devpack
36 |
|
missing 7906
default load 8.2(1) |
|
7985 |
|
Packets
received on PC port are not forwarded in some configurations |
|
7985 does not
display animated icon w/ RTPRx |
|
Restart
reason sometimes is not correct under Network status |
|
Phone can
rarely stop making calls after CCM failover/failback |
|
Confrence
List Remove feature does not work on CCM 5.0 |
|
Invalid
dialed number when dialed from directory displays no information |
|
Exit softkey
sometimes does not work on Callback window |
|
Callback
Notification window does not close after Dial is pressed |
|
Phone
sometimes does not fallback to the correct Standby CCM |
|
Wrong display
of softkey sets and callinfo on IPMA assistant phone |
|
IPMA manager
should not exit from IPMA service w/ 1 assistant |
|
Phone did not
register with the Call Manager after a network power loss |
|
Phone
unexpectedly reset during a long duration H.263 call |
|
Some softkeys
not work correctly with CiscoIPPhoneInput object |
|
7985 phone not
working with Mobile Connect service. (CMM/SNR) |
|
7985
un-registers from the Call Manager after the switch speed changed |
|
Network
status should contain last restart reason |
|
Hoot &
Holler service does not display Handset icon with RTP/Rx RTP/Tx |
|
Visual call
Pickup notification fails when line audio alert setting off |
|
7985- Ignore
CDP V1 message for VLAN configuration purposes |
|
Equation type
input can have unexpected delay when pressing numbers |
|
Pressing a
number in Ring Tone menu works differently than other phones |
|
There is no
Call Status information available via the web pages |
|
7985 appends
devicename in HTTP request when searching directory users |
|
Changing
volume during the Hoot & Holler service cause audio to be sent |
|
Hoot &
Holler icon was not removed after exiting the service |
|
Background
image after download is obscured by the image menu |
|
7985 can not
handle URL with 255 char. |
|
PC Voice VLAN
disabled does not work with Admin VLAN |
|
IPPA phone
service shows some unexpected error messages when logging in |
4.1-Devpack
35 |
|
7911/7941/7961/7970/7971 |
|
Beep tone max
power is only -22dBmO |
|
FSCK stuck in
deadlock with syslogd |
|
DSP
Configuration Files are not Correct |
|
Enumeration
Pattern Code Updates |
|
Phone sends
corrupted RFC2833 packets when SRTP enabled for call |
|
Dev Studio
changes to make building Communicator easier |
|
Secure phone
does not retrieve the SEP file |
|
7931- Call
Plane Detail View is not open after On-Hook dialing |
|
CiscoIPPhoneStatusFile
LocationX parm not used for small image size |
|
Commit of
CSCef34402 broke c6slc, other? pikespeak images |
|
Titan dsp
host could 32-bit read between dsp firmware two 16-bit writes |
|
Osage- Max
Input Rxd msg displayed when 32 chars input to Shared Secret |
|
Power Save
Configuration options missing in Settings |
|
Osage- Status
Messages for 802.1X Authenticatio not as per Osage UI spec |
|
softkeys
disappear after blind directory transfer |
|
TNP- keyboard
I/O errors on reset |
|
RTCP- Exiting
Hoot & Holler cause phone to send bogus BYE packet |
|
7931-
Exception in OverviewModel during restart |
|
Support G.722
56k and 48k in the Audio Server |
|
TNP phone
logs "Unable to get memory" message on console |
|
pressing
volume key then speaker button can lock up phone |
|
G.722
K-Factor Table incorrect |
|
Highlighted
Call isn't displayed if 10th call ended leaving 9 held calls |
|
7970/7961-
dtmf burst is played with a double duration |
|
Phone does
not send un-register message to SRST on fallback to CCM |
|
7931-
Pressing Line button does not change Line focus |
|
Onhook
dialing produces delay in feedback sound with last digit |
|
IP phone
fails to do HTTP authentication |
|
7931-
Overview not in home position at initial bootup |
|
RTCP socket
open error may cause audioserver to spin |
|
under is only
20 chars instead of 64 |
|
Dynamic Trace
level registration results in file create/delete operation |
|
EAP-Request/MD5
to PC supplicant could not pass thru Gig phone |
|
Static
Analysis Codebase Cleaning on Select Files |
|
7961 phones
not processing CTI request to disable softkey |
|
TNP-
dhcpRcv.c - uninitialized variable |
|
7970- Phone
lock up when message URL has max or 255 character |
|
IP Phone
should re-DHCP immediately after DHCP NAK |
|
7931- scroll
up and down, sometimes a leftover icon appear next to label |
|
show
inventory command returns no data |
|
RTCP- SDES
packets are not being padded correctly |
|
Idle Prompt
for SRST cannot be set back to the default value |
|
Phone not
sending DHCP traffic to pc port |
|
Unable to
dial from external dir list after cancel edit dial |
|
LCD display
does not always show status of 3 consecutive lines |
|
7911G
experiences loss of registration |
|
SIP phone
show "Connected" in call preservation if user in/out line disp |
|
7961 with
voice vlan resets if IPC is connected to 3rd vendor switch |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Ringing phone
ICON keep showing up on the phone display without call |
|
Skittles-
Retain Dialplan from CCM while failing over to SRST |
|
IP phone not
direct HTTP request to proxy server w/ unresolved DNS name |
|
Phone does
not have "End Option" field with DHCP Release message |
|
Incorrect DSP
Configuration File Formats |
|
RTP Tx URI
request should be rejected when a call is active |
|
goped won't
autoscroll to previous line/call in multiline scenarios |
|
3rd gen
phones running 8.0(4)SR1 unable to adjust ringer after a call |
|
When uri is
not responded by user, second uri post just hangs forever |
|
Clean up
debug options available / messages |
|
Line DN label
appear to be shifted a pixel or two to the left on Display |
|
Digit tone
improperly continues until call connect |
|
JPN hone
freeze at Cisco Logo after reset due to Java OutOfMemory error. |
|
7961/70 fail
to transfer a call with line 2 from Directory |
|
TNP- Remove
NULL term from hostname in DHCP request |
|
7971 displays
"Ethernet Disconnected" briefly |
|
Phone core dump
when terminating mulitple calls |
|
phone not fallback to CCM and shows
"Restarting...". |
|
Enumeration
Pattern Code Update |
|
Mute Button
is enabled when Phone Speaker Button throws Error pass Limit |
|
On turbo the
overview is distorted when a new call is created and ended. |
|
Osage-
Transaction Status does not update unless menu is re-entered |
|
TNP SIP phone
uses wrong default TLS port number |
|
Handsfree
Receive Frequency Response does not meet the mask |
|
debugsh- set
LOG_DEBUG trace level for sunvm.cnuw/ debug SIP/JVM command |
|
Phone does
not detect Invalid Load Server IP address for "A.B.C D" |
|
Phone Ringsin
Continuously,Need to power off/on to clear the call |
|
7911 SLR is 5
dB softer than required, its ok in GL mode |
|
IPPM- Phone
displays XML Parse Error when accessing Contact List |
|
7961 - PC
cannot see data traffic if PC Voice VLAN Access is disabled |
|
TNP SIP phone
can not handle long Unicode callid/linetext |
|
7931- Clean
up OverviewModel ACTIVATE_REQUEST event handler |
|
Osage- Phone
drops incoming unicast EAPOL when VVLAN is present |
|
7970 Runs out
of memory as phone when idle URL is used |
|
7931- Phone
looses softkeys when exit from IDLE URL screen |
|
Incorrect
values in RX/TX_START_TIME and/or REPORT_TIME pegs |
|
TNP phones on
CME can't resume call with Line button |
|
Focus does not
shift to off-hook line while another call is incoming |
|
Soft factory
reset does not clean files from /etc/sfr.tab |
|
RTCP- With
RTCP disabled web StreamingStats Report Times are invalid |
|
Include
Kernel.core into the sylog files for debug purpose |
|
Not able to
use Dial Sofkey in Corporate Directory |
|
TCP not
sending all posted data after socket close |
|
7911/41/61/70/71
- 2 concurrent XML posts result in Error 0 or Error 6 |
|
devoplement
build (TNP) script does not work |
|
Dial Softkey
should be disabled for corporate directory/PAB/FastDials |
|
Turbo- DoS
tool icmpsic crahses phone on Bugtrap 0x93 |
|
offhook w/
handset for the first time after reboot, no dialtone is heard |
|
Unmount Error |
|
HTTP sessions
are not currently aged-out |
|
CreateStringMatchProperty
does not update the allowedValues |
|
TNP - 7911
phone needs an 802.1X port lookup mechanism |
|
9 lines with
call in Hold Reversion, phone stops ringing |
|
provide for
next generation static analysis for TNP |
|
RTCP- BYE
packet has padding bit mistakenly set |
|
7941/7961/7970/7971
Aliasing in high band when using wideband headset |
|
7931-
LineFullDisplay detail is missing from the title |
|
Call History
Enhancements for Chumbawamba Phase 1 |
|
7970- reduce
msg sizes being used in network daemon IPC |
|
Static
Analysis Codebase Cleaning on Select Files |
|
When calls
are selected/unselected, sorting is done immediately |
|
TNP -
7971G-GE forwards 802.1X packets twice |
|
Exit softkey
stops UI when in Security Configuraiton/CTL File submenu |
|
7931- May
have a Java Memory leak in disposeDynamicFeature |
|
Static
Analysis Codebase Cleaning on Select Files |
|
IP phone
stuck at Cisco Logo screen when reset from CCM w/ sidecar |
|
Can not login
to phone during automation testing |
|
Network
Locale Version backwards compatibility |
|
support
persistent status line display on SIP phone in SRST mode |
|
Phone throws
exception upon going off-hook |
|
Dial URI w/
Active Call doesn't Invoke Call Options when no app in focus |
|
Static
Analysis Codebase Cleaning on Select Files |
|
7931 Titles
in Line FullDisplay aren't left aligned at at the same place |
|
Phone
continues to ring after shared line picks up a transfered call |
|
mipspacker
not use CNU versioning for BN2 image |
|
7931- Line
number overlayed with ellipses ... while in active call |
|
7970 SCCP
requires Authorization when hitting **# to unlock the phone |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Phone Service
unavailability message corrupted |
|
UDI Time Zone
not displaying string from phone config file |
|
7931-
Handsfree RLR does not meet the spec |
|
Phone not
showing "Duplicate IP Adress" in status line |
|
HOST Field
Send IP Address Instead of Defined Hostname |
|
7911 Phone
speed and duplex settings not saved |
|
CP-7971 does
not cache TFTP address if option 66 set TFTP server name. |
|
TNP phone
sends StationSubscriptionStatReqMessage at restart |
|
Focus changes
to the new ringing call before 10 secs.. |
|
Reset on
sleep mode phone would not put it back to sleep mode |
|
CiscoIPPhoneDirectory/DirectoryEntry/Name
should be restricted to 32 cha |
|
TNP- check
return value when writing dhcp.conf |
|
Remote in use
calls with no caller ID should display "To Unknown Number" |
|
Sanity- Core
produced for rtsp on restriciting incoming bandwidth/bitrat |
|
Fragile file
cleanup and performance enhancements (Jasmine featurette) |
|
7931- Tuk Tuk
noise heard while using wideband codec for a call |
|
7970 Phones
have incorrect active display during shared line call |
|
SIP phone
should reattempt download of softkey&dp on TFTP down/ timeout |
|
For Cbarge
"CM down,features disabled" message not displaying on 7970 |
|
7931- Headset
icon not displayed when Headset LED is pressed |
|
Expand
Directory object name field to accept 64 characters |
|
7931-
Softkeys disappear with 4 sofkey templates |
|
7971 should
set Audio Preference to default values after Erase |
|
Muffled voice
on receive for some calls |
|
cnu recover
second look |
|
7911-
GroupPickUp does not work |
|
Unknown name
displayed if special characters are in display name |
|
7970-DHCP-
Rejects DHCP request with option 15 from CNR |
|
Display on
shared-lines not-in-call is not consistent in cBarge scenario |
|
7931-
Incorrect call appearance on shared trunk monitor calls. |
|
Call Focus
shifts to Held call for consultative conference call leg |
|
TNP - Soft
factory reset should clear 802.1X PAE info |
|
7931- Enable
video support |
|
Focus is on
wrong call when line view is opened indirectly |
|
Change the
7906 BN2 to use RELEASE keys for pilot build |
|
Turbo should
not advertise G.722 |
|
Dynamic
features like BLF Speed dial and Privacy are not working |
|
Call fails
when no dialplan and registered to SRST |
|
Conference on
Alerting with 8-0-2-4S load |
|
Update 7911
diagnostics to version 10.02.00.06 |
|
CNU kernel
BugTrap 0x91 with V-E-R-Y specific conditions |
|
TNP phone
stuck in blank screen during upgrade to 8.0(3) load |
|
third-gen
phone 8.2(1) recover process is not displayed |
|
dsp ingress
frame timestamp not following RTP RFC3550 |
|
sleep()
system call not POSIX compliant |
|
AbbrDial key
shouldnot be active when speakerbutton is disabled |
|
Text Item
Displays are not right justified in RTL locales |
|
Phone should
explicitly turn on display when reset/lost registration |
|
SIP phones
should Ignore unknown softkey set names in softkey xml |
|
7931- Add
icons to the DetailsFullDisplay |
|
CIA-680
Support on 3rd gen phones |
|
revertPriority
setting not used for 1st call after changing the setting |
|
Third-Gen
phones running 8.0(3) do not hear multicast audio from RTPMRx |
|
8.2 phone
load causes robotic issue at customer site |
|
Dialplan is
not supported when Failover to SRST |
|
Highband
noise reduction tuning |
|
Bugtrap 0x91
phones (during fsck) |
|
unable to
disable kpml on TNP phone registered to CME |
|
TNP- send
DISCOVERs if no DHCP server can be found |
|
IP phone
reset with DOS attack |
|
7941/61 LCD
controller must be reset at startup time. |
|
Arabic locale
missed QRT on dest info |
|
Empty Dial
list is getting displayed on phone |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Default
router entry removed when dup ip present |
|
Can not press
line 36 on 7970 with 2 sidecars |
|
7931- Unable
to answer call on 2nd line using phone handset |
|
"On
" prompt doesn't always work |
|
Static
Analysis Codebase Cleaning on Select Files |
|
TNP-
"show inventory" CLI output not adhering to the specificication |
|
redial sk is
not active in onhook state |
|
getEndPointInfo
reports MWI setting incorrectly |
|
vm -mem
broken on Broadcomm platform (7941/61, 7970/71) 8-2-0-20 |
|
LCD display
shows status of Lines 22-24 after phone boots up not 1-3 |
|
Turbo- DHCP
recv socket error on bad address |
|
SenderJoins
& Byes values were different regardless of call status |
|
Osage- 7961GE
stops receiving EAP-Req/ID during long duration reset test |
|
Static
Analysis Codebase Cleaning on Select Files |
|
7931- Doesn't
show IDLE display on phone display after restart from CME |
|
TNP phone
fails to display the switch info at its webpage |
|
7970-PNG
image file download crashes the phone |
|
SYN ACK
messages from phone not DSCP tagged |
|
Jphone-
Navigate problem under network statistics menu when debug mode |
|
make property
retrieval from RMS store file effecient |
|
Handsfree SLR
does not meet the spec |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Add volume
control for local and network tone |
|
7931- Speed
dial does not display called-id when another line offhook |
|
Selective graying
out of AudioPref menu items incorrect on inline power |
|
Need to Press
Right button twice on Nav Pad to close Line Detail |
|
Placed calls
are not multi-party and should not show a MP call history |
|
Phone
Continuously displays "Requesting...". |
|
Softkey wrong
after fallback from SRST |
|
7961 (and
7941,7970,7971) doesn't display Call park number after getting |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Static
Analysis Codebase Cleaning on Select Files |
|
7931-UI shows
lines 22-24 when line button pressed with AppMenu Open |
|
Settings
-> Device Configuration -> UI Configuration menu is missing |
|
Call History
Lists inaccessible after having max entries and deleting 1 |
|
7931- Phone
restart from CM duration test leads to Disk full |
|
Add SIP
related changes to support G722 for ph0 of wide world |
|
Missing
Pixels on the left side of UI displays on Turbo phones |
|
phones should
not advertise Voice VLAN on PC port |
|
JTest-
SIPCCAdapter.java switch statement missing breaks |
|
7931- Factory
Reset Walk LED pattern is only 16 |
|
7971 phone
reverts to old config after changes saved to netwk config |
|
7931- LEDs
for lines above 8 do not illuminate |
|
debugsh
should support RTCP trace |
|
Cfwdall fails
to come back on CCM after fallback from SRST |
|
7914 displays
old version of remote-in-use icon |
|
Line LED not
lighting up or delayed on incoming calls |
|
Phone display
not turned on when going into reverting state |
|
TNP SIP Phone
resets after auto register due to default load info missin |
|
PNG Broken-
Phone fails HTTP GET if earlier HTTP request is not finished |
|
Pushing RTPRx
or RTPMRx URI to phone in a call enables mute |
|
Call
Statistics menu- Sender size is not a correct format |
|
SIP phone UI
Locks up and Keypresses ignored (still registered w/ CCM) |
|
UI locks up
& phone cannot register |
|
Timer
Exception seen in TimeDateRequest |
|
Clear softkey
does not work in Status messages screen |
|
Outgoing
ringing and incoming ringing tones played at same time |
|
apply patch
for Diab compiler from WindRiver |
|
Add new tone
messages to make traditional/stutter tones selectable |
|
Phone
accepting duplicate IP |
|
Static
Analysis Codebase Cleaning on Select Files |
|
7911,
7906,7931 & 7921 have poor voice quality with G711alaw codec |
|
Out of Memory
- Connection refused errors after duration testing |
|
Turbo- 1st
incoming call can't be answer if 2nd one be connected first |
|
RTCP- RR/SR
packet is missing some info when there is 2 report blocks |
|
SIP gives
different Error message than SCCP in Locations scenario |
|
7931- IDLE
URL Refresh timer doesn't work in 66DEV image |
|
Shared line
display & going offhook while in active call distort display |
|
Write to the
TNETV105x PCNTRL "Access Control Reg" must be 16 bit |
|
TNP-
libcso.map from build should be saved |
|
New Features
- Auto Call Select and More Key Timer |
|
7931- Leave 1
pixel space w.r.t. App Menu/Headset/etc |
|
Line reports
as unregistered, but it's not, after failover |
|
Re-sync tone
table if dsp host re-starts |
|
Phone core
dump while running the call features automation script |
|
Phone not
retrying the re-IP after dup IP |
|
7961/41
Speaker LED on even after pushing End key |
|
SETTINGS
softkey does not work if no DHCP server available during bootup |
|
mount command
exiting with status code 64 |
|
KATE Input
causes NPE and non-password data while using XML services |
|
u7961/41/70
stuck at requesting after phones inbound web access disabled |
|
SCCP phone
does not register back to publisher after restart. |
|
Need an API
to assign a local port to TLS connect |
|
LineModel
dispose call throwing a ClassCastException |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Dialer does
not close correctly after Cancel or Idle Timer Expires |
|
Need filter
coeficients for headset, handset and speakerphone |
|
TNP Phone
7941 second line line button will light up for incoming call. |
|
Static
Analysis Codebase Cleaning on Select Files |
|
Multi-Party
Call History - Transfer case - Received call "from" details |
|
Audio Server
K-Factor table for G.722 |
|
CNU Flash
Filesystem not recoverable if it fills up |
|
certcnu.bin failure- GETCNU- CNU image update failure; code = 10 |
|
Status of BLF
SpeedDial does not get updated. |
|
need feature
parity between sip and sccp phone for speed-dial |
|
Endcall
softkey doesn't work in Call Preservation |
|
Answer and
DnD Softkeys are not always displayed when a call is rcvd |
|
Idle sftkeys
displayed on new incoming call after transferw/rel image |
|
softkey
disappears on the phone after several calls are made |
|
7970
precedence call waiting tone does not stop |
|
Issue with
Pegs when the call is remotely held and on MOH |
|
wrong
filepath used after posting a TFTP file |
|
Phone should
send the 433 Anonymity Disallowed for anonymous calls |
|
Diagnostic is
alway reloaded into the primary slot |
|
Turbo- Speed
dial entries not at designated position |
|
Calling/Called
Info not correct for SIP TNP phones |
|
Double call
sort after ending selected call |
4.1-Devpack
34 |
|
Adding 8.2(1)
features to CCM 3.3, 4.1, 4.2, 5.0 |
4.1-Devpack
33 |
|
NewCall and
EndCall should not be mandatory softkeys |
|
7921 |
|
Need update
to "devicelistx.asp" to support new Cisco 7921 wireless phone |
4.1-Devpack
32.1 |
|
Update 7921 CSV
and XML files for FCS |
|
7920 |
|
7920 3.0.1
FIrmware and XML Schema Check In |
4.1-Devpack
31 |
|
Unable to
insert 7941 phone with Device Security Mode as Authentication |
|
CCM4.1(3)ES. SQL error when inserting a 7961 phone |
|
Add support
for Security feature in Communicator |
|
3.0.1 English
Dictionary Check In |
|
Link 'View
the User Guide for your phone' not available for 7961/7941 |
|
6608 E1/T1 |
|
6608 T1 cas
channel rejects outbound calls |
4.1-Devpack
30.4 |
|
CCM4.1(3)ES. SQL error when inserting a 7961 phone |
4.1-Devpack
30.3 |
|
CCM4.1(3)ES. SQL error when inserting a 7961 phone |
|
7902/7905/7912 |
|
Phone
response status inconsistent between models |
|
7912 phone
should not send StationFeatureStatReq if feature is not confi |
|
7905Japanese
characters are shown as ?s in EM screens |
|
CP-7912 can
not use 255 as last octet of SRST address. |
|
IPICS Channel
selection by select key does not work intermittently |
|
DnD fails on
7912s |
|
7912 w/alt
tftp disabled does not read TFTP server from DHCP |
|
7912 can not
resume multiple calls from hold |
|
Connection
Monitor Duration changes not applied to 7902 |
|
7912 cannot
make new call after lisfting handset |
|
Malformed XML
Delieverd from 7912GA when using DeviceInformationX |
|
No response
to UserToDeviceData for Key:xxx URI passed from CTI |
|
Init:CallHistory
URI does not re-set status line on 7905 |
|
call waiting tone doesn't stop when the second call hangs
up. |
|
7912 prefixes
fastdial with 'undefined' |
|
7912 affected
by ARP storm |
|
7912
authentication problem - password encoding |
|
IP Phone
Service problem with 7912 http redirect v8.0 |
|
Able to
Change Ring Volume Even when Setting Access set to Disable |
|
7912G-A phone
does not obtain address when voice vlan = access vlan |
|
CIA 650:
Randomize TimeDateReq's to Call Manager from 7905/7912 |
4.1-Devpack
30.2 |
|
No web access
cfg option for 7941/61 in CCM device configuration page |
4.1-Devpack
30.1 |
|
Unable to
insert 7941 phone with Device Security Mode as Authentication |
4.1-Devpack
30.0 |
|
Update 7921
CSV file to add Prefer Alternate Script option |
|
7940/7960 |
|
Build phone
loads |
|
JPN-Cancel
softkey not available for configuring 7960+7914 |
|
phone
displays Select Ringer... for Invalid DistinctiveRing.xml |
|
UI screen is
grayed out when i-button is pressed |
|
Autodial
cancelled is shown for a Phone in RingIn state |
|
Phone
displays AutoDial Cancel in transfer scenario |
|
7960 tries
fallback to CCM that has CCM service shut but port 2000 open |
|
Phone Softkey
should be greyed out for Disable Speakerphone and Headset. |
|
7960 produces
garbled audio and repeated words for PA Help |
|
Softkeys
within various Settings submenu not responding if held |
|
DN not
displayed in a hold scenario after line button press. |
|
Init-CallHistory
URI does not re-set status line on 7960/7905 |
|
Phone displays
Callmanager parameter as UNDEFINED to boot up process |
|
revertPriority
= Even fails when Hold Reversion call is oldest |
|
Integrate DSP
rev 4.0(2) |
|
parked calls
get loud tone when picked up from 7960/40 on CME 4.0 |
|
Callback can
not be activated for a busy extension |
|
Abbreviate
dialing should not be available if phone not able to call |
|
need to press
line button twice to answer an incoming call |
|
Mute light
stays on after audio broadcast is complete |
|
ST- 7960
secure phone got TLS error with SRST after CCM 4.2.2 upgrade |
|
one way voice
when the timestamp field in the RTP packets rolls back |
|
RTP Tx URI
request should be rejected when a call is active |
|
7960 does not
differentiate local hold call and remote hold call |
|
40/60 - LA
dev size grown above acceptable size limit |
|
7960 with
voice vlan resets if IPC is connected to 3rd vendor switch |
|
phone doesn't
handle the DHCP next server field and option 66 correctly |
|
7960 displays
XML error on hitting directories button with French locale |
|
Phone hangs
with HIGH CPU detected- during EM logout & locales installed |
|
6608 |
|
6608 PRI
Gateway stayed up even when CCM lost connection |
|
6608 shows
wrong OID |
4.1-Devpack
29.7 |
|
6608 PRI
Gateway stayed up even when CCM lost connection |
|
Link 'View
the User Guide for your phone' not available for 7961/7941 |
|
7935/7936 |
|
Phone Button
does not work |
|
7936 with
4.2SR1 cannot dial digits when in call state 3 (Ring Out) |
|
Scrolling to
the end of the line in EditDial causes 7935/7936 Reboot |
|
7936 not
passing DTMF while in alerting state. |
|
DTMF tone
will not play for consecutive same digits with 7936 |
|
Display is
not uniform when dialing an non existing number |
|
Mute dosen't
work with |
|
Phone dosen't
ring while viewing the MAC address details using **6 |
|
7935 and 7936
do not support 40, 50, and 60ms frame sizes |
|
Phone
displays In Use Remotely with out shared line in SRST mode |
|
LED Status
changes when the Transfer softkey is selected in SRST mode |
|
7935/36 need
to support the priority field in DisplayPriNotify message |
|
Polycom 7936
doesn't refresh after saving the Alt TFTP address |
|
Main/Secondary
TFTP Address cannot be modified when DHCP is disabled |
|
Conference
not working on 7936 in SRST mode |
|
7936 Phone
does n't allow/display full domain name. |
|
7936/7935
does not support JOIN feature of CCM 4.0 |
|
Renumber 7935
firmware load name to match |
4.1-Devpack
29.6 |
|
6608 T1/E1 |
|
6608 PRI
Gateway stayed up even when CCM lost connection |
|
MGCP backual
message with length of 12 bytes |
|
Router
identify a very short DTMF as a valid DTMF |
4.1-Devpack
29.5 |
|
Add support
for Security feature in Communicator |
4.1-Devpack
29.4 |
|
Merging local
dictionary in CCM |
4.1-Devpack
29.3 |
|
Jphone
software changes to address Memorex enhancements in EDCS-505798 |
|
Support RTCP
featurette |
|
New Features
- Auto Call Select and More Key Timer |
|
Add nightlight
features |
4.1-Devpack
29.2 |
|
Add 7921
support files (CSV, XML, GIF) to CCM |
4.1-Devpack
29.1 |
|
7985 |
|
Phone ignores
DHCP option 150 when option 66 is present for TFTP server |
4.1-Devpack
29 |
|
7914 |
|
Implement
SeaDragon features |
|
7940/7960 |
|
7960 phone
does not clear status line during reset |
|
pressing line
button on ipphone doesn't switch between detail &overview |
|
Posting
Line34 URI enables Line30 on ip phone. |
|
7960- Does
not preserve the state of mute/spkr button in handset mode |
|
7960 drops
the incoming call when using the IPICS services. |
|
7960 phone
does not handle HTTP code 401 for push request |
|
Phone-
Authentication username/password takes only 31 characters |
|
CiscoIPPhoneInput
takes * and # when input is set to N |
|
StreamingStatisticsX
not backwards compatible |
|
7960- Call
being on hold is NOT sorted by Select function |
|
7960- Doesn't
update CDP cache when no voice vlan present in CDP message |
|
7960 DSP
Logging utility broken |
|
7960 does not
display via |
|
IP reassembly
broken |
|
IP phones
become unregistered from both SRST and CM |
|
7960/7940
phone stuck at CONFIG IP after a reset/power cycle |
|
Phone load
Upgrade to 7.2(3) causes RXshort errors on PC port |
|
Phone drops
untagged PC Traffic |
|
HTTP 100
Continue from phone malformed |
|
Remove use of
linked directory in SCCP BA |
|
7960 - XML
Debug PUSH behaves erratically |
|
Handle
Current Call missing when dialing from Directory |
|
Phone rejects
menu responses from server- Fastdial, Corp Dir |
|
Callback
notif (Dial) & Park while already in an active call fails. |
|
GARP
enable/disable ignored |
|
The phone
crashes when it receives invalid Response.ContentType in HTTP |
|
Secure Phones
does n't cancel tftp request while cancel key is pressed |
|
7940/60 PC
port 100M does not receive network traffic intermittently |
|
7960/7940
Rcvr Lost Pkt reports as a negative no under impairement |
|
Unable to
dial the CB notified number during ringing state |
|
No sidetone
during first phone call following phone registration |
|
Phone
performs unneeded ARP when Garp enabled |
|
Phone removes
ARP entries too quickly |
|
help for settings button not displayed when setting key is
disabled. |
|
DHCP enabled
Phone resets with held call when alternateTFTP changed |
|
Phone doesn't
display held call in detail view when barged call ends |
|
Promts is
Truncated to 20 Characters when using Greek Locale |
|
Phone resets
if we dial Half of the DN on-hook & remaining off-hook |
|
Speed dial
from Monitor DN is not working with 7.2.2 |
|
phone display
Remote-In-Use menu when the other end resume the call |
|
DIALED Number
missing in CFA where the target phone is 7940/60 SCCP |
|
Update 7960
built-in font to include new zero with a slash |
|
7960/40
cannot register in autheticated mode CCM 4.1.X OS 2000.4.2 |
|
Phone resets
during high bandwidth traffic to PC |
|
Placed calls
are recorded on all shared line phones |
|
Missing
SpeedDials on phone after upgrading the phoneload |
|
7960 crashes
when more than 20 calls placed via stress script |
|
Placed call
list under directory gets updated only for Connected calls |
|
7960- Unable
to reset phone when other shared line is busy |
|
Phone strip
dialed Number in Directory Placed call list for PSTN call |
|
7985 |
|
The phone
does not honor the Connection Monitor Duration fallback value |
|
Phone may
malfunction if more than two lines configured. |
|
Telnet
xstatus command under DNS/Domain Name contains non-ascii letters |
|
Need to add
support for IP phone service |
|
IPMA is not
supported with 7985 video phone |
|
Add screen
saver to 7985 |
|
XML support |
|
Three or more
line appearance needed |
|
Ocius should
have a contrast and white balance configuration options |
|
save button
placement cause user to end call |
|
Directories
menu does not display for 15 seconds when URL is unavailable |
|
Background
image support is required |
|
Phone crashed
when 100 calls active and remote side is lost |
|
7985 does not
play the MLPP premption tone |
|
Settings
Erase softkey is displayed even when config is locked |
|
7985 video
endpoints do not support services. |
|
Packets from
the PC port are not being forwarded out SW port |
|
7985 crashed
when attempting to originate a call from WebDialer |
|
Phone does
not ring at all if the selected ring tone is not available |
|
Error message
on missing ring tone is different than 7970 |
|
Phone never
boots up when background image is changed |
|
Phone does
not detect changes to the CM background image list file |
|
7985 does not
do Authentication for CiscoIPExecute |
|
7985- HTTP
redirect not work |
|
7985-
CiscpIPPhoneIconMenu oject parse error |
|
7985- HTTP
refresh not work |
|
7985- two
items missing from phone's web access page |
|
7985 not
display Authentication URL on Device Configuraiton menu |
|
7985 should
have Power Save Configuration menu |
|
Device ID in
CDP messages should all be in upper case |
|
7985 takes
too long to re-register when image load is not found |
|
7985 not back
to power save mode if restarted from CCM |
|
Alpha Numeric
fields use different key mappings than other phones |
|
7985 not back
to power save mode after a call coming in |
|
7985- phase 2
image does not support asp URL pushed to the phone |
|
7985 should
exit Service app after login w/ ExtensionMobility |
|
7985 (X)
button toggles between Full Screen and Overlay modes |
|
7985 only
shows 6 lines w/ Privacy and Speedial configured |
|
7985 does not
display To conference at line button menu |
|
Callback
activation tone is not heard when using TFTP Server 2 |
|
7985 not
registered to its CCMs |
|
7985 not
update call status icon at line button menu |
|
Hanging up
the phone does not work when failover occurs during call |
|
7985 crash
when Execute Object is pushed to phone with proxy config |
|
7985 got
authentication error |
|
7985 can not
list PAB entry |
|
7985 displays
white line at full screen |
|
7985 does not
send out video packets w/ IPMA configured |
|
There is no
Cancel softkey when requesting a phone service |
|
Berbee
services do not work on 7985 |
|
Softkeys in
the Berbee phone service do not work properly |
|
MyGroup IP
service returns back John Chambers' group instead |
|
7985 should
exit from Setting menu by pressing Setting button |
|
7985 Error
message different when URL DNS name error |
|
7985 crash
when wake up from power save mode |
|
7985
incorrect behavior when get HTTP Error 404 |
|
Camera
Properties need a wider range of changes |
|
When
upgrading the software the status line is stuck |
|
Left/Right
arrows should change the monitor brightness values |
|
7985 could
not display FastDial page |
|
7985 Update
at service page does not work |
|
Phone crashed
while looking at the eventlog during an active call |
|
Video between
7985s momentarily blurs out |
|
7985 crashs
while answering a call |
|
Remote side
video stops working when hold/resume rapidly pressed |
|
7985 should
close the listening chanel when service app is closed |
|
Exit an IP
phone service returns the user to the top of the service list |
|
Phone takes
DHCP option 150 in the wrong order |
|
Conference
call info status is displayed as the the 4 instead |
|
Digits after
first call state softkeys are messed up |
|
Calls for
status line is corrupted after pressing directories button |
|
The From
status line displays no number on an incoming call |
|
|
|
Phone should
drop from full screen mode during an incoming call |
|
7985 Push
Execute failed with Internal Error |
|
7985 crash w/
call on hold |
|
7985 does not
disable SSH after reset |
|
985 fails
over to SRST after ethernet cable replugged in |
|
7985 does not
change Camera properties back to default value |
|
7985 should
not display Erase key at CameraSettings menu |
|
7985 plays
wrong Ring Tone |
|
7985 does not
save selected Ring Tone if RingList.xml not available |
|
HELP ID- Help
for Camera Settings returns help for Monitor Brightness |
|
HELP ID-
Brightness Hue Saturation help returns main help topics instead |
|
7985 set
button template wrong w/ one button set as None |
|
7985 crash
when access Help Main menu |
|
7985 fails to
display Video Mute icon when incoming call answered |
|
Video mute
line status icon is lost after a hold/resume |
|
Placed Calls
Directory entries have a %s as part of the display |
|
Background
& Ring don't reset when Restore Default Settings is involked |
|
Downloaded
Background & Ring list missing when TFTP Server 1 is down |
|
7985 crash
when Line key pressed on Help Menu |
|
X button does
not work in Service w/ Host Not Found Error |
|
No Help Info
for Transfer softkey |
|
No Help Info
for NewCall softkey |
|
No Help Info
for More softkey in onhook state |
|
No Help info
for Dial and Cancel softkeys in onhook dialing state |
|
No Help Info
for NewCall sofktey in Remote-In-Use mode |
|
Softkey sets
mess up after access Help in Callback mode |
|
No Help info
for ImmDV and TrnVM softkey in ringin state |
|
7985 should
include Camera Setting info on View Setting menu |
|
Forwarded to
status message not display the DN |
|
7985 displays
?1001 status message when in Setting menu |
|
X New Missed
Calls should not persist w/ new incoming call |
|
7985 does not
support Restricted Setting Access |
|
Phone crashed
pressing the Search softkey on Corporate Directory |
|
Next softkey
does not work in Corporate Directory |
|
Wrong
softkeys when looking at an empty Missed Calls list |
|
Cancel
softkey has no impact while downloading Background images |
|
7985 play
ringer to handset for a second call |
|
Softkeys
disabled after change audio source w/ Handset off the crack |
|
Forwarded
Call Infomation Display not as configured |
|
Softkey sets
changed after pressing Line button |
|
7985 should
switch back to the first call after 2nd disconnected |
|
7985 behavior
inconsistant with 2nd incoming call |
|
Wrong softkey
sets for barged call |
|
7985 displays
Remote-In-Use icon after barge into a call |
|
First ring
tone in ring tone list is the letter a |
|
Cannot easily
answer incoming call while in Missed Calls Directory menu |
|
7985 call
status message mess up for shared line |
|
7985 shared
line Call Info display different from other phones |
|
7985 should
initiate a new call on shared line by selecting the line |
|
7985 not show
the CallInfo of shared line on line menu |
|
Dial key not
work on FastDial |
|
7985 should
always use first avail. line for Dial from Directory |
|
7985 should
allow number with 25 digits at PAB |
|
7985 not
fallback to primary CCM if the CCM restarted |
|
7985 does not
have Next Softkey at Berbee main menu |
|
No Update
softkey for graphicMenu and image |
|
7985 not work
with directory.asp |
|
7985 fails to
display No Park Number Available |
|
PAB service
URL does not work |
|
ExtensionMobility
ServiceURL button not work |
|
IP Phone
service - My Group does not work properly |
|
7985 flash
light not blinking for Callback |
|
Denial of
Service tcpsic script crashes the 7985 |
|
Personal
Address Book edit Name returns 400- Bad Request |
|
7985 not
display Softkeys with position more than 5 |
|
7985 could
not display Directory object with maximium value |
|
7985 crash
when pressing Softkey-Next and Softkey-OK |
|
Phone does
not recoginize SoftKeyItem/Position object |
|
7985 gives
parsing error with IP Phone Agent Service |
|
7985 crashed
when running a image slide show IP service for 10 minutes |
|
Fast Dial
phone service should be allowed to Assign up to 32 digits |
|
Call
Information is not displayed after pressing Settings button twice |
|
7985 gives
incorrect Error Code for XML parsing error |
|
Phone help
does not work |
|
7985 gives
ParseError if IPMA realtime update stopped |
|
7985 crash
when press Exit at IPMA assistant service |
|
7985 does not
display Exit key w/ Parsing Error |
|
Phone does
not fallback off SRST router after call is terminated |
|
7985 crashes
when attacked with some Denial of Service scripts |
|
Phone
displays a ? instead of line feed on directory
listing output |
|
Blackjack IP
phone service returns error after 1st key press |
|
IPPA service
Agent Login screen password entry is displayed in the clear |
|
Phone directs
some http requests to the proxy url when it should not |
|
PC Voice VLAN
disabled does not work |
|
Line button
not work if not all line buttons are assigned |
|
7985 should
change focus to the active call after exit from Setting menu |
|
No Help ID
for IPMA related softkeys |
|
Softkeys are
confusing when in the Lines menu |
|
Cannot hang
up a call when the call comes from a shared line |
|
IPPA service
briefly displays some XML code during start or state change |
|
7985 crash
with broadcast traffic at Voice Vlan |
|
HELP ID-
Background Image help returns Help Topics instead |
|
One way video
or black screen or no video over VPN observed |
|
7985 XML
input - Uppercase & Lowercase input types allow invalid chars |
|
7985 XML
Input - Some Input types with password field flag show password |
|
7985 XML
Input - Equation type input doesn't allow symbols |
|
7985 should
exit from Service app by Exit key w/ EM login page |
|
Could NOT
hangup call on shared line after restart |
|
7985 New HW
does not suppress upstream Broadcast, multicast traffic |
|
7985 video
phone crashes when it receives cisco gateway fax NSE |
|
QED (CSV and
Display XML file) Changes for Phase 2 Ocius 7985 |
|
7985 not
support softkeyitem as Key-KeyPad |
|
Berbee IP
phone service returns- unable to display service error |
|
7985 should
not clear Status object |
|
7985 should
not append its Devicename in HTTP Get messsage |
|
Softkeys
under the settings menu are misaligned |
|
Phone status
log should contain more information |
|
One way video
seen on call between 7985s |
|
Ringing stops
playing when the volume is adjusted during incoming call |
|
Phone is
using the callback tone as a ring tone on next call |
|
7985 reboots
if Option 150 is a String Data-Type |
|
7985 XML
Input - equals character (=) looks like a solid, heavy dash |
|
Audio sources
do not work on next call after a failover with call active |
|
Cannot change
audio output source when failover with active call occurs |
|
Error message
is truncated when invalid Admin VLAN is entered |
|
Localization
needs to be turned off on the phone |
|
Softkeys are
unavailable after pressing the Window button |
|
Help for
Power Save Configuration returns help for Camera Settings |
|
Help within
the Power Save Configuration returns Main Menu Help instead |
|
Help of SW
Port Configuration returns help for PC Port Configuration |
|
Stock quote
IP phone service crashed the phone |
|
Domain name
cannot be entered when phone doesn't have an IP address |
|
HELP ID-
Power save configuration returns help for Display On |
|
Network
Configuation Default softkey should be renamed to Erase |
|
User
Preferences Default softkey should be only available when unlocked |
|
The popup
window after pressing Default should be more specific |
|
7985 - Power
save exits XML Service (and menus) |
|
Configuration
parameters domain name and DNS servers lost after upgrade |
|
Phone
rebooted when using Hoot & Holler with 2 phones in Shout mode |
4.1-Devpack
28.2 |
|
Device
Package installation has dialog come up in silent mode |
|
7906/7911 |
|
7906/7911Check
in 7906/11 f/w load to CCM |
|
7935/7936 |
|
DTMF tone
will not play for consecutive same digits with 7936 |
4.1-Devpack
28.1 |
|
Link 'View
the User Guide for your phone' not available for 7961/7941 |
4.1-Devpack
28 |
|
CCMAdmin
should not offer option of 72XX voice platform as a MGCP GW |
|
Make 7906
(turboprop) appear in device defaults and device pulldown FCS |
|
7906/7911-Checkin
user guide and update CSV files for online user guide |
4.1-Devpack
27.7 |
|
QED (CSV and
Display XML file) Changes for Phase 2 Ocius 7985 |
|
CIA-680
Support on 3rd gen phones |
|
Call History
Enhancements for Chumbawamba Phase 1 |
|
CCMAdmin
should not offer option of 72XX voice platform as a MGCP GW |
4.1-Devpack
27.6 |
|
CCMAdmin
should not offer option of 72XX voice platform as a MGCP GW |
|
ENU
Coltrane3.0 Check In For English-US Locale |
|
7920 |
|
Coltrane 3.0
Firmware Check-In |
4.1-Devpack
27.5 |
|
Digital Access WS-X6608 |
|
6608
Incorrect marking DSCP value to 0 |
|
6608 shld not
automatically clr connection when ICMP unreachable is rcvd |
4.1-Devpack
27.4 |
|
Main client
is not usable when find dialog is up in topo window |
4.1-Devpack
27.3 |
|
7935/7936 |
|
Cannot use #
or * as first entry while onhook |
|
7936
vulnerable to ICMP attacks |
|
7936 doesn't
send HTTP Get with multi tier DNS names in Directory URL |
|
Can't place a
call from phone book when it receives a missed call |
|
Phone cannot
be resetted to factorydefault when Admin paswd is not known |
|
Remote party
hears echo when 7936 used in glass conference room |
|
7936 accepts
invalid IP Address and Subnet mask |
|
7936 accepts
invalid Alternative TFTP Address |
|
Access Admin
Setup without entering the passcode |
|
Conference
not working on 7936 in SRST mode |
|
Web interface
allows to change password with different characters |
|
7936 Web
Interface allows different characters in Phone Book |
|
7936 Web
interface dosen't prompt for password when phone is restarted. |
|
7936 phone
retains the meetme session even after the call manager fails |
|
phone may not
give Error tone when incorrect phone number dialed |
|
7936 Editing
phone Book doesn't have the asterisk in the required field |
|
If call
received while editing ring tone and publisher fails, 7936 hangs |
|
7936 Web
interface accepts alphabets in |
|
Phone will
not accept incoming call while waiting for |
|
7936 Takes
long time to register when PINGED with CCM failover |
|
Info for |
|
Polycom 7936
doesn't refresh after saving the Alt TFTP address |
|
Polycom 7936
allows to change the Ringer settings in Ringin state |
|
Phone book
entry on the web display is not proper |
|
7936 reboots
when you configure Admin VLAN id while in active call |
|
7936-Call
Transfer number is not displaying in SRST mode |
|
Park
Information retained for a long time. |
|
DN not
displayed while placing the call on hold & initiating a new call |
|
Call
initiations fails from the phonebook with CFwdAll |
|
Phone
registers with Alt TFTP when Alt TFTP Address not specified. |
|
Phone hangs
when used Diagnostics with CCM failover |
|
Mute turns
off in this scenario in 7936 version 3-3-7-0 |
|
Second Call
on shared line cannot be resumed or muted |
|
7935 &
7936 Polycom phones lockup on failover, loss of call preservation |
|
Display issue
when Meet-Me number is 10 digit |
|
Phone does
not accept to change the passcode with valid characters |
|
ncorrect
display on one of the phone in sharedline |
|
Incorrect LED
status on a phone in shareline with call waiting enabled |
|
7936 Transmit
Jitter Extremely Sporadic - 2 Second Cycle |
|
7936 won't
fallback to a TFTP server once registered to an SRST router |
|
7936 Phone
use odd RTP port numbers |
|
7936 phone
with phone load 3-3-8-0 does not work for FAC |
|
7936 Outside
dial tone sounds the same as inside dial tone |
|
Call gets
disconnected if we press hold & resume multiple times |
|
7936 does not
play tone 50 (Zip) when someone joins a conference |
|
Phone display
is incorrect when a bogus phone load is entered. |
|
Phone dosen't
ring when **8 is executed |
|
Phone hangs
during failback and failover with meetme |
|
Phone
displays Registering after CCM failover in a active call |
|
Dial tone
stops when phone receives a missed call |
4.1-Devpack
27.2 |
|
ITA Display
of Zero and CAPS O - 7960 Font Display |
4.1-Devpack
27.1 |
|
7911 Add
support for Vieo |
|
Placeholder
CDETS for Turboprop Feature Commit |
4.1-Devpack
27 |
|
Name Change
Cisco Unified CallManager 4.2 - ES/SR Wrapper |
|
7985 |
|
Domain Name
shows up as? when it is not populated by DHCP |
|
Onhook
dialing does not light Speaker LED in SRST mode |
|
On help button ? page, Back softkey doesn't work |
|
Requesting
better administration tools |
|
Video
pixelation on calls made between Cisco VT Advantage and 7985 |
|
7985 Improper
system message wording |
|
There were no
tones heard when using onhook dialing |
|
No
notification on phone when the remote end of a call is lost |
|
Call focus
switches off active call when shared line is used by others |
|
Default
router field periodically resets when phone is configured |
|
7895 may
report multiple Standby CCMs after fallback |
|
Phone does
not ignore lower valued Voice VLAN when multiple CDPs recvd |
|
Phone may
stop ringing when switching to a second incoming call |
|
Headset mode
sends output to the Speaker in SRST mode |
|
Sometimes
cannot answer 2nd call by switching lines in SRST mode |
|
Phone
sometimes does not direct audio to the handset in SRST mode |
|
Call Forward
icon still displays when fallback to SRST mode occurs |
|
When using
EditDial of a number the prompt should start at the beginning |
|
Rarely the
MWI light is on even when no messages are pending |
|
Phone does
not send periodic CNG packets during long silence breaks |
|
Call Waiting
Ring setting will only Flash the MWI lamp during 2nd call |
|
Video may
freeze at end of call or in self-view mode |
|
Switch should
ignore PC Voice VLAN Access when there is no voice VLAN |
|
802.1p frames
dropped on phone with Admin VLAN and PC voice VLAN disable |
|
Phone gets
stuck in CallManager Unavailable state |
|
Test script
causes a watchdog timer expiration |
|
Packets to PC
port are re-mapped with 802.1p when Voice VLAN is 802.1p |
|
EditDial
followed by lifting handset will not dial call |
|
Phone may
continue to display Self View rather than idle screen |
|
Denial of
Service mutant script cause the phone to reset |
|
Sometimes
phone cannot end call after a CCM fallback with call active |
|
Web Access
Enabled/Disabled need to be added to CCM and phone |
|
Phone
sometimes does not connect to correct backup CCM during fallback |
|
Phone does
not reset when lower numbered Native VLAN learned |
|
Video mute
state get out of sync after the phone is restarted |
|
Phone
sometimes shows wrong status msg/softkeys after CM service restart |
|
Cannot browse
under Directory, Up/D rocker stuck at the Missed Calls |
|
Phone drops
~50% of IP multicast traffic from SW to PC port |
|
7985 MWI
Light misbehavior |
|
7985g reboots
after select softkey then hit the X key |
|
7985 does not
play precedence call waiting tone |
|
7985 phone
does not display call pickup visual alerts |
|
7985 crashes
when running Codenomicon TCP protocol verification suite |
|
7985 phone
reboots when pressing the 'Directories' or '?' buttons |
|
CCM4.2 -
Cisco 7985 Phone softkeys disappear during Pickup Audio Alert |
4.1-Devpack
26.3 |
|
Placeholder
CDETS for Turboprop Feature Commit |
|
7941/7961-7970/7971 |
|
no value for
some items on Device INformation page |
|
Phone should
display ... for very long Text or Number |
|
SSO Standby
RP T/B atm_ha_decode_vc_update+0x23c for ATM PVC bundle |
|
Phone
registered to a CM 3.3 shows only one line while call on hold |
|
Received and
missed calls show wrong calling party number |
|
Time stamps
on console messages and phone display is not the same |
|
Deselected
call in sorted call list appears with other selected calls |
|
Turbo Gabage
at the end of Network Statistic screen |
|
Cancel
softkey has delayed response when looking up a bogus DNS addr |
|
Phone resets
wmore volume of call are placed on sidecar lines |
|
wbm failed to
extract signature when display filter was used |
|
Turbo Can not
remove Doamin Name on phone |
|
Phone does
not remove the default router config |
|
Increase max
CPU usage timeout for JVM process |
|
SIP TNP 1.1
image stress run freezes phone UI |
|
Phones unable
to Rx or Tx Multicast Services when Publisher fails. |
|
Phone w/200
calls active single line reset w/calling phone reset |
|
dhcp.conf
could have invalid my name entry |
|
Add consolle
trace to indicatie the call is an encripted call |
|
Phone doesn't
register when it is unable to resolve the CCM name |
|
paging group
display delayed on 7911 with CME |
|
get SW port
returned -1 error after downgrade to 6.0(2)SR1 |
|
Phone stops
playing multicast after an unanswered call |
|
local Ip/port
value is cleared but others are kept for an ended cal |
|
LED does not
blinking red while the DCP is busy |
|
7970/7971
Touch Screen issue IP Phone URL shows Delay |
|
logins with
sys group permissions on release signed phones |
|
Skittles
timeZone tag errors |
|
Turbo
Background Image thumbnails not displayed in correct order |
|
7961 Row of
Pixels missing on Line View graphic |
|
Skittles
phone locks up when SEP |
|
Skittles
phone locks up when SEP |
|
Phone display
goes blank for consult transfer to busy monitor line |
|
when PickUp softkey is pressed on onhook phone displays
??? |
|
Sittles
Service URI cause phone to crash |
|
need to press
mute twice for an incoming intercom call |
|
Assign a same
IP port to RX and TX socket - casues 1 way audio |
|
Phone doesn't
play Zip/ZipZip Tones toward network |
|
Phone Rcvr
Lost Pkt reports as a negative no under impairement |
|
SIP TNP DSP
debug seen when pressing Settings, Directories, or Services |
|
Reference
getPegs() via IMedia interface instead of directly |
|
Turbo Phone
receives mcast pkts when port open forMcast transmit |
|
Turbo Error
Verifying Config Info after LSC install on secure phone |
|
README-SGM-pdsources
on DVD has SGM references |
|
Phone Should
handle gethostbyname failure and print appropriate Err Msgs |
|
Phone not
displaying all Placed call list when pressing up/down button |
|
Corporate
directory search fails if username contains special characters |
|
wirelss
client to client can not pass traffic |
|
Service URL
feature assigned in em profile does not work |
|
Phone sends
Duplicate DHCP Discover Message |
|
Phone freeze
after reset stress |
|
Phone
displays wrong msg when registration rejected for security reason |
|
phone doesn't show up old admin vlan id in Current Admin.
VLAN Id |
|
Corporate
Directory Search Fails When using Russian Locale |
|
Add Title to
Line View to identify which line the calls belong to |
|
Having
directory menu open causes Callback to not working properly |
|
Exit soft key
is not working in Callback Screen |
|
HTTP CGI
ModeInfo query does not return if Services URL doesn't resolve |
|
Ethernet
Disconnected Mesasge does not appear when Ethernet unplugged |
|
Turbo Missing
status messages on Load Server parameter |
|
No status
message when TFTP service is down on load server |
|
LineInfo web
age query does n't show up Messagewaiting Indication. |
|
Phone won't
failback to a TFTP server once registered to an SRST router |
|
HTTP req
canclled msg when hitting a softkey |
|
Japanese
locale (td-sip.jar) not loading on SIP phones. |
|
Removing JVM
from 7.0 on 8.0 CPK files (to avoid out of space errors) |
|
Turbo status
message No Default Router after changing DHCP=no to yes |
|
Phone does
not preserve the state of mute/spkr button in handset mode |
|
Skittles
phone does not complain with junk value in displayOnDuration |
|
Making DSP
standalone on phones- dsp.cnu reads dspfw.bin |
|
select image
Userpreference->Background image display invalid png icon |
|
CDP crashs
from broadcasted CDP pkt, results in restart of all apps |
|
Privacy lamp
is not being displayed correctly on 7941 SCCP phone |
|
add
fault-tolerance to filesystem |
|
Phone unable
to come out of Service Menu using CANCEL softkey |
|
Phone
responds to CDP triggers from upstream port |
|
phone does
not play precedence CW tone |
|
Calls drop
during CME failback |
|
Phone is
stuck if Encrypted Config is on and supporting load is absent |
|
phone doesn't
come up with DHCP enable when Voice VLAN = Access VLAN |
|
Incorrect
response for unicast/invalid IP adress for RTPMTx i p URI |
|
CiscoIPPhoneExecute
ExecuteItem priority 1 is ignored in some cases. |
|
Invalid Ip
Address to be displayed while validating Null values. |
|
Turbo lost
audio w/ 100% broadcast traffic |
|
Status Msg
timestamps changed between 24hr/12hr formats on reset |
|
CP-7970
firmware version 7.0(1) distorts background image color |
|
Softkey
changes from Connected Transfer state to On Hold state |
|
Phone is
loosing the querystring parameter on the refresh |
|
Phone
Multicast services not working |
|
LSC Installed
Status Messages is not displayed on phones |
|
cBarge Target
phone changes focus when other party cBarges |
|
Phone doesn't
dial from placed call listwhen editdial& dial is pressed
. |
|
Phone
Displays UI with no keys for a shared line scenario. |
|
Phone CGI
URLs never complete HTTP transaction |
|
Services page
text does not display properly |
|
Idle phones
never send SCCP TimeDateReq to sync clock |
|
Pressing the
'.' soft key in the edit menu doesn't force Kate String T/O |
|
Clicking
noise is heard in encripted call when duplicating packets |
|
Phone plays
garbled audio for PA prompts |
|
phone displays ??? as Codec in Call Statistics window |
|
Call Stats
window displays wrong info for Rcvr Lost Pkts/Discarded |
|
IP Phones use
random UDP source port for RTP media |
|
Phones stop
sending KA when backup TCP link down |
|
call bubble
does not disappear when there is no active call |
|
High End
Phones connect to CCM sub that is not present in the CTL file |
|
Turbo
fine-tune displaying errors of dspSendFrame _framePutEgressFrame |
|
Turbo
InsideDialTone could not be stopped after removing CFwdAll |
|
UDI Support |
|
Turbo
Codenomicon HTTP test 39730 causes sunvm CPUTime Limit Exceeded |
|
Add core file
decoded core file to the serviceability webpage |
|
SIP phone
loads and CCM are out of sync for PC Voice VLAN Access |
|
GARP
enable/disable reversed |
|
Property
Errors - Settings Can Be Lost |
|
phonerebooting
when secondary CME inaccessible and keepalive is 10 |
|
Enhance the
flush operation in the RecordStore |
|
HTTP Client
locks up upon consecutive posts to CGI Execute |
|
No
prompt/status in Detail call history record |
|
Dial Softkey
Enabled when no Active Audio Path or no CCM |
|
Erase from
Top-Level Settings Menu does delete sidecar contrast |
|
SIP Phone
does not do a TLS session reuse after network failure |
|
RMS Store
must be deleted in order for phone to boot correclty. |
|
Phone stuck
after erase under Settings menu |
|
JPhone
Overview displays incorrect topcall if some RIUs made private |
|
GARP enabled
native code returning incorrect value |
|
Phone could
not recover after DNS entry be corrected |
|
Phone sends
Invalid Message for SCCP v3 and v4 |
|
Phone Answer
softkey not displayed for new icoming call |
|
Remote In Use
Icon/LED not shown when shared line is private |
|
HTTP
Authentication Does not Show Response |
|
Able to
Change Ring Volume Even when Setting Access set to Disable |
|
TimeDateReq
to sync clock causes KeepAlive to miss one interval. |
|
7970/7971
InCorrect Date Format Shown Under Missed Calls |
|
2 meg file
limit cause double boot when upgrading to 8.0 load |
|
JAVA/TNP
Log/trace related changes |
|
CNU syslog
changes for 7.0.2.x branch |
|
getportcfg
check for errors on msgsnd() |
|
Display
distorts, when held calls goes from three to two |
4.1-Devpack
26.2 |
|
CMM Echo
Cancel Coverage 8 and 16 ms should be removed |
4.1-Devpack
26.1 |
|
ATA18X |
|
ATA SCCP
Incorrect Call Waiting behavior |
|
Conference to
ATA-Phone thru H323 & ATA-phone on same CME doesnt work |
|
ATA flooding
callmanager with Softkeyevent New call skinny messages |
|
Problem
transfering calls using ATA and CME |
|
Update
signaling ToS to be consistent with current design guides |
|
ATA186
configuration web page should state clicking rather than click |
|
ATA SCCP sent
AVT message when sent DTMF to SCCP endpoint |
|
No Secondary
dialtone played by ATA SCCP |
|
ATA186
excessive TCP ACK delay after receiving SKINNY message |
|
ATA SCCP
sends excessive StationSendTimeDateReqCSCef39491 |
|
7940/7960 |
|
Phone without
DHCP cant recover Dup IP address |
|
7960/7940
characters by pressing '0' with li-ffr.4-1-3-JPN are funny. |
|
help symbol
missing in text press - key to cancel for english locale |
|
7960 Settings
-> RingType menu changes doesn't take effect |
|
7910 DSCP
values need to be consistent with current design guides |
|
EM logout
restarts the IP Phone. |
|
Small MTU
causes CVTA to H323 video call failure |
|
7960/7914
Ringer type off by 4 lines. |
|
Update
dictionary file with SeaDragon new phrases |
|
Phone
Continuously displays Requesting RingList File ...... |
|
Phone UI
Lines separating the DN disappear as it failover to subscriber |
|
Posting
Line34 URI enables Line30 on ip phone. |
|
http // |
|
ActiveSoftkeys
eg redial, New Call are shown when pubisher CCM is
down. |
|
In CallInfo
the CalledPartyName field is not proper for Conf call |
|
In http
request for CallInfo/LineInfo the Prompt field is showing null |
|
Line button
does not answer call with 2 calls on hold already on line |
|
DHCPReleaseMessage
should be unicast to DHCPserver,not on broadcast IP. |
|
7960 Phone
doesn't display blank URL sign or URL without label on line |
|
Volume
control keys when calling a busy no affects ringer(ver 8.0(0.16)) |
|
7960 Phone
reset from settings with **#** while on call hold |
|
7960 Phone
loose RTP stream when restart from CM |
|
7960 Pressing
Line button twice ends calls on Phone in ringing state |
|
BigApp does
not kick back to LA on version mismatch in XMLDefault.cnf.xm |
|
phone
7940/7960 should escape '#' symbol |
|
7960 doesn't
receive MOH or DHCP when Voice VLAN = Access VLAN |
|
RED LAMP
indication on 7914 for In Use Remotely does not work - 7.2(3) |
|
7960 MWI
functionality should be consistent with current phone behavior |
|
7960 Phone
volume not being set properly at RTPRx start |
|
Menu object
as IDL URL, menu item 1 selected when phone goes off-hook |
|
MWI lamp
glows continuosly after a CB notification for the first set CB |
|
IP phones
become unregistered from both SRST and CM |
|
Phone load
Upgrade to 7.2(3) causes RXshort errors on PC port |
|
Phone drops
untagged PC Traffic |
|
Handle
Current Call missing when dialing from Directory |
|
Secure Phones
does n't cancel tftp request while cancel key is pressed |
|
7940/60 PC
port 100M does not receive network traffic intermittently |
|
Unable to
dial the CB notified number during ringing state |
4.1-Devpack
26 |
|
6608 E1/T1 |
|
Calls through
6608 T1 CAS trunks are not preserved |
|
T1-CAS
E&M ports on a 6608 card unregistering during stress test |
|
Periodic
T1-CAS E&M channel out-of-service during 6608 stress test |
4.1-Devpack
25.4 |
|
CM need
support for new phones in devicelistx.asp file |
4.1-Devpack
25.3 |
|
ES/SR
Installation needs corresponding code for CSCsb44801 resolution |
|
Enlarge splashscreen in ES/SR installaton |
|
Need new
sections for file copy ops |
|
Update SQL
script handling |
|
Enhance error
handling reporting and dialogs |
|
End of
installation Dialog Changes needed for Device Package |
|
7911 |
|
Checkin 7911
f/w loads to create Device Packs for FCS |
4.1-Devpack
25.2 |
|
Implement
group listening. |
4.1-Devpack
25.1 |
|
7902/7905/7912 |
|
7912 fails
due to malicious VLAN tagging |
|
7912 does not
play |
|
7905/12
phones lose Service button after EM update |
|
phone - 7912
phone reboots after receiving 3 IMs quickly |
|
Only a 7912
shared number phone work when configured max-dn dual-line |
|
No dial tone
after the 7905 and 7912 SCCP failover to SRST |
|
7912G-A
phones cause PC's behind them not to retain an IP Address |
|
Long delay
for PC to obtain network connectivity when used with 7912G-A |
|
7912/05
should always Reset unless an rtp stream is active |
|
CCCM 5.0
& 7905/12 does not show external number on top line of display |
|
7912 SCCP
sends excessive StationSendTimeDateReq in idle mode |
|
7912/05
excessive TCP ACK delay after receiving SKINNY message |
|
7912/05
RTPMTx sets TTL of sent multicast packets to 1 |
|
Timedate req.
msg. storm from at midnight |
4.1-Devpack
25 |
|
PCM change
breaks 4.2 and lower builds. |
|
7935 |
|
CP-7935
generates choppy audio when in a conference call |
|
7920 |
|
Extension
Mobility does not work with Services URL Button on 7920 |
|
7920 Doesn't
Support Vibrate URI |
|
Need a menu
to display configured regulatory domain |
|
Need a menu
to display current transmit power |
|
7920 Does Not
Support CCA Versions of QBSS |
|
7920 can
spontaneously re-register to CM in idle with INF-MIB error |
|
7920 Can
Associate to a Lower Priority Profile When Set to Auto Profile |
|
Upgrade to
2.0 will cause phone lock password corruption |
|
CCM 5.0
Centralized TFTP compatibility enhancement |
|
Port
17185/udp is open on 7920 phone |
|
7920 RTPMTx
sets TTL of sent multicast packets to 1 |
|
7920
call-forward noan on second active call results in phone hanging |
|
7920 can
corrupt the CCKM Timestamp |
|
Invalid XML
object sizes can cause the 7920 to reboot |
|
Idle URL can
cause the 7920 to lock up |
|
7920 will
roam off a strong signal AP to a weaker one |
|
7920 should
continue streaming RTP packets when on Mute |
|
7920 can fail
to ACK G711 packets during a call |
|
7920 Can Roam
More Frequently With 12.3(7)JA AP Image |
|
7920 Can Stop
Scanning Although Still Associated |
|
7920 send
802.11 Auth suddenly and it causes choppy audio |
|
Channels in
Active List are not flushed after 3 missed CM Keepalives |
|
Emergin's
alert tone volume needs to be limited when on-call |
|
CP-7920 is
not responding to AP packets |
|
MWI tone can
be very loud to user if CP-7290 re registers |
|
Need to roam
when QBSS max threshold is met |
|
7920 MR2.0.1
firmware upgrade |
4.1-Devpack
24.9 |
|
7936 |
|
7936 Transmit
Jitter Extremely Sporadic - 2 Second Cycle |
4.1-Devpack
24.8 |
|
Need tag for
6608-MTP/CFB in ccm xml |
4.1-Devpack
24.7 |
|
VG224
configured for shared line on Callmanager fails |
|
help symbol
missing in text press - key to cancel for english locale |
4.1-Devpack
24.6 |
|
Update/Make
7911 ready for FCS and prepare Skate SR build |
4.1-Devpack
24.5 |
|
7.0(2)SR1
image for the 7941/7961 checkin to 3.3, 4.0 and 4.1CCM release |
|
7970/71
7.0(2)SR1 image check in |
|
Add online
doc. name to 7911 SCCP loads |
|
Stndrd
Feature 7960 sftky profile fail on 7940 CallBack equipped phone |
|
Update/Make
7911 ready for FCS and prepare Skate SR build |
|
7941/61 |
|
Phone freeze
after reset stress |
|
Exit soft key
is not working in Callback Screen |
|
CDP crashs
from broadcasted CDP pkt, results in restart of all apps |
|
Privacy lamp
is not being displayed correctly on 7941 SCCP phone |
|
add
fault-tolerance to filesystem |
|
Phone
responds to CDP triggers from upstream port |
|
phone doesn't
come up with DHCP enable when Voice VLAN = Access VLAN |
|
7970/71 |
|
Unknown resolved defects |
|
4.1-Devpack
24.4 |
|
Application
menu items should not be in all CAPS |
|
CM need
support for new phones in devicelistx.asp file |
4.1-Devpack
24.3 |
|
6624 |
|
change
configuration link is not opening for 6608 & 6624 GWs. |
4.1-Devpack
24.2 |
|
remove
loggingDisplay option for 7941...7961G-GE phones from CCM/Windows |
4.1-Devpack
24.1 |
|
VG224
configured for shared line on Callmanager fails |
4.1-Devpack
24 |
|
7941/61 |
|
checkin
7.0(2) firmware for 7941/7961 phones into CCM/Windows |
|
7970/71 |
|
7.0(2)
firmware for 7970/71 |
4.1-Devpack
23.2 |
|
6608 T1/E1 |
|
change
configuration link is not opening for 6608 & 6624 GWs. |
|
CallManager
may incorrectly put a 6608 CAS port OOS |
|
6608 Glare
conditions on T1 CAS is not cleared appropriately |
4.1-Devpack
22.7 |
|
7940/7960 |
|
Greyed ERASE
softkey is actually enabled |
|
Caller ID
gone from shared line after a barge |
|
>in
7940/60 i-button help text |
|
sidecar lamp
shows red for barge/cbarged calls |
|
7960/40
Device Info page does not follow Message Waiting Lamp Policy |
|
Display
settings on Phone should be changed for Restricted Display |
|
7960 can load
a Ringlist.xml with more than 50 entries |
|
Remove
conditional code |
|
IPPS
authentication credentials, % sign not URL encoded |
|
PC can't ping
7960 phone with dot1p configured |
|
Next key not
displayed for CiscoIPPhoneDirectory that appears in Service |
|
ARP cache
timeout if set 0 in 7960 phone flood the n/w with ARP queries |
|
7960/7940
characters by pressing '0' with li-ffr.4-1-3-JPN are funny. |
|
Build
P0030701T018 ES Load |
|
30th digit of
Speed dial display text is not properly displayed |
|
7940/60 plays
multicast from other VLANs as well as the voice VLAN |
|
phone reboots
after several hours of operation over high delay network |
|
CDP code does
not verify destination MAC address |
|
7940/60
Little App accepts DHCP Offer from a different VLAN |
|
No Display
for dialed number thru personal fast dial/directory lookup |
|
Loader |
|
7960 Settings
-> RingType menu becomes unresponsive |
|
Unwanted
Debugs appear on Console |
|
* and # are
causing settings softkey to be updated in settings submenus |
|
7960 Line
text Label contains garbage when sent to SRST router |
|
Inconsistency
in Streaming Stats between web page and phone when MoH |
|
Second 7914
expansion module displays garbled characters |
|
7960 phone
drop G.729b frames when silence suppression is on |
|
7960 - DHCP
broadcast for renewal instead of unicast at 50% lease time |
|
Setting menu
Softkeys intermittently are not responding |
|
7940/60 sends
AdminVVLAN in response to CDP Trigger with VVLAN query |
|
Phone sends
extra off-hook message |
|
PC connected
to 7940/60 has slow network communication |
4.1-Devpack
22.6 |
|
PC logging
option is not available for makaha |
|
Analog Access WS-X6624, |
|
Digital Access WS-X6608 |
|
GW config
page for cat6kT1 VOIP shows fields required when optionl |
|
Change
configuration fails to open the GWconfigpage over securechann |
|
Clicking help
in gatewaypage prevent users from viewing device info |
|
change
configuration link is not opening for 6608 & 6624 GWs. |
|
CCM4.1.2 web
page for Gateway device config should be https |
|
6608 T1 CAS
channels are stuck in CSCallClearing state |
|
Inactive
channels are not busied out when 6608 loses CCM registration |
|
6624 FXS
ports stuck in offstate state / ReleaseInd Q931 state |
|
7935 |
|
7935
susceptible to ping attack, causing odd/delayed behavior |
|
Using keys
during call causes chopiness |
|
7935 loses
connectivity on voice RTP broadcast packets reception |
|
CP7935/CP7936
Does Not Support DTMF Out of Band |
|
7935s did not
come back up after upgrade from Parche to Skate |
|
After a CCM
upgrade phone displays rebooting..... |
|
7935/7936
Phone does not support broadcast suppression |
|
Slow audible
feeback for key presses |
|
TFTP Client
Behavior - 2 TFTP Servers |
|
7936 freezes
after on-hook dialing |
|
6608 Lost
packet counter is increased by 16 for every press of DTMF tone |
|
Phone
requires power-cycle if publisher fails while Call Waiting in prog |
|
Mute doesn't
work on 7936 (Call waiting enabled) when publisher fails |
4.1-Devpack
22.5 |
|
7936 |
|
Using keys
during call causes chopiness |
|
CP7935/CP7936
Does Not Support DTMF Out of Band |
|
7935/7936
Phone does not support broadcast suppression |
|
Slow audible
feeback for key presses |
|
TFTP Client
Behavior - 2 TFTP Servers |
|
7936 freezes
after on-hook dialing |
4.1-Devpack
22.4 |
|
Add 7985 QED
support CCM versions 4.X and 5.X |
|
7911 QED
changes to support alt scripts and load server |
|
Checkin
ip7961.pdf ver3 into3.3.5.eng.spec, 4.0.2.eng.spec, 4.1.2.eng... |
4.1-Devpack
22.3 |
|
Enable
visibility of Makaha types in dev packs 3.3.5.eng.spec, 4.0.2. .. |
4.1-Devpack
22.2 |
|
Enable
visibility of Makaha types in dev packs 3.3.5.eng.spec, 4.0.2. .. |
4.1-Devpack
22.1 |
|
GW config
page for cat6kT1 VOIP shows fields required when optionl |
|
Change
configuration fails to open the GWconfigpage over securechann |
|
Clicking help
in gatewaypage prevent users from viewing device info |
|
change
configuration link is not opening for 6608 & 6624 GWs. |
|
CCM4.1.2 web
page for Gateway device config should be https |
4.1-Devpack
22 |
|
1700 GWs FXO
ports are allowed to be configured for diff signaling. |
|
MLPP config
not available for 3845 MGCP gateway |
|
Enable
visibility of Makaha types in dev packs 3.3.5.eng.spec, 4.0.2. .. |
4.1-Devpack
21.5 |
|
7985 |
|
Add 7985 QED
support CCM versions 4.X and 5.X |
4.1-Devpack
21.4 |
|
Mandatory
parameter URL help has to be present by default |
|
7961/7941
font should be more readable - suggest making taller |
|
7910 |
|
7910 fowarded
call display syntax error |
|
SD1C Phone
firmware parses phone config file incorrectly |
|
Phones To Be
More Ambitious Towards Updating Firmware |
|
Echo fades in
and out when talking IP phone to IP phone |
|
Ip Phone
doesnt accept option 66 with trailing dot in hostname |
|
Slow
performace when data AND voice vlan is tagged (802.1q) |
|
Callwaiting
does not work on 7910 ip phone |
|
Disabling
settings w/o disabling ring volume |
|
Dial keys do
not respond for 10 secs after pressing **# |
|
7940/7960 SIP
phones not handle out of order/mis-sequence packets |
|
Phone fails
to come up when wrong load Id is mentioned on phone page |
|
7960 send
StationAlarm w/ incorrect text if no RegAck |
|
Faint audio
is heard in the speaker while using handset |
|
Set Ringer
Duration ignored by Seaview phone registd with ParcheCCM |
|
7910 should
not drop the 1st call by pressing line on 2nd call |
|
An error at a
certain key sequence |
|
7910 conf
phone does not displays called/calling name |
|
Key rollover
broken/missing digits when dialling |
|
C3PO Frame
Buffer overflow causes COS3 packet drop |
|
Audio cut
through delay during Call Waiting Answer |
|
7960/7940
Voice Quality Degradation With Echo Back To Remote Party |
|
TFTP 2
address edit display contains garbage |
|
7910 ip
displays connected call information wrongly |
|
7910 phone
having DN of 24 digits reboots if CFA number crosses 9 digit |
|
7910 phone
does n't displays fwd for forwarded intercluster call |
|
7940/60
handset/headset SRL/RLR mid-spec adjustment |
4.1-Devpack
21.3 |
|
1700 GWs FXO
ports are allowed to be configured for diff signaling. |
|
ONLINE HELP
Ring tone help screen needs to replace Alert with Ring |
|
ONLINE HELP
Device Configuration help need updated with new submenus |
|
ONLINE HELP
Help info for editing IP address needs addtional steps |
|
ONLINE HELP
Erase softkey help under Settings needs more information |
|
ONLINE HELP
Help for Network Settings DNS Server 1 returns error |
|
ONLINE HELP
Default softkey under some User Preferences returns no help |
|
No Help
content for the softkey OPickUp. |
4.1-Devpack
21.2 |
|
1700 GWs FXO
ports are allowed to be configured for diff signaling. |
4.1-Devpack
21.1 |
|
Video
capability for Communicator has to be added |
|
Maketypes
needs run after Product CSV's added to branch |
|
support for
EM2-HDA-4FXO in CCM |
4.1-Devpack
21 |
|
7.0 firmware
and associate files checked into CallManager |
4.1-Devpack
20 |
|
7920 |
|
IP phone
services do not work |
|
Need
Capability to Disable Configurable Menus |
|
7920 Should
Be Less Aggressive for LEAP |
|
Softkey
Templates Do Not Work with 7920 |
|
Duration
fields are occasionally wrong in 802.11Data null packet |
|
7920 does not
support virtual carrier sensing |
|
7920 Red
button cannot end call when far end busy |
|
7920 placed
call log may not include discarded digits |
|
No
Connectivity After Downgrade to 1.08 When Using Static WEP |
|
Ringtones are
displayed incorrectly when less than 4 rings available |
|
7920 can
change focus to another line when on call |
|
7920 user
guide cannot be loaded from CCMUser pages |
|
Intermittent
AP retransmissions if 7920 is unavailable |
|
7920
Sometimes Roams Unexpectedly Due to Packet Loss |
|
7920 can get
stuck in a scanning state |
|
7920 does not
look at source port for Multicast |
4.1-Devpack
19 |
|
Turbo-Some
line settings not available |
|
6608 MTP/CFB |
|
Tertiary CM
not listed in Transcoder Device Configuration Page |
|
6608 cfb
unregisters after one missed keepalive |
|
conference
bridge not getting registered to correct ccm |
|
ICMP Hard
error handling for 6608 MTP/CFB |
4.1-Devpack
18.4 |
|
7.0 firmware
and associate files checked into CallManager |
4.1-Devpack
18.3 |
|
7912 |
|
7905/12
display English prompt at Services page |
|
Issues with
processing of DNS packets |
|
Settings
Access restricted option behaves like enabled on 7912 |
|
7912 can not
initiate hold w/ multiple calls per line and shared lines. |
|
The browser
window on the 7912 opens when it should not |
|
There is no
dial tone when exiting from the directory menu |
|
7912 Chinese
Locale Unable to display calling number |
|
CHS-Wrong
Phone display |
|
DTMF when
users mash 7912 keys unrecognizable to AA/IVR |
|
7905/7912-Does
Not Format '?' Characters in Services URL Properly |
|
XML Error
[4]-Parse Error on 7912G when creating FastDial in PAB |
|
Found dtmf
digits fail when calling into Meeting Place IVR. |
4.1-Devpack
18.2 |
|
7961 Phone
Icon missing in the Call Manager Find/List Phones |
4.1-Devpack
18.1 |
|
7902/05/12 |
|
7905/12
display English prompt at Services page |
|
Issues with
processing of DNS packets |
|
Settings
Access restricted option behaves like enabled on 7912 |
|
7912 can not
initiate hold w/ multiple calls per line and shared lines. |
|
The browser
window on the 7912 opens when it should not |
|
There is no
dial tone when exiting from the directory menu |
|
7912 Chinese
Locale- Unable to display calling number |
|
CHS- Wrong
Phone display |
|
DTMF when
users mash 7912 keys unrecognizable to AA/IVR |
|
7905/7912-
Does Not Format '?' Characters in Services URL Properly |
|
XML Error
[4]-Parse Error on 7912G when creating FastDial in PAB |
|
Found dtmf
digits fail when calling into Meeting Place IVR. |
|
ATA18X |
|
ATA has poor
voice quality when NumTXFrames set with high value |
|
ATA (SCCP)
does not process Calling Party Name in second CallInfo |
|
Issues with
processing of DNS packets |
|
Unable to set
UI password for ATA188 |
4.1-Devpack
18 |
|
7902/05/12 |
|
TFTP Client
Busy Retry Behavior |
|
7912 doesnt
display correct Softkeys when using MCDN feature |
|
IP Phone 7905
not responding to http commands |
|
7912 cant
ring immediately when receiving a call after fallback |
|
MWI will be
turned off by incoming call |
|
7905/12
display English prompt at Services page |
|
7912 ignores
StationClearPriNotifyMessage from CME |
|
Authentication
delay between IP Phone 7905 and CM 5.0 is to long |
|
Issues with
processing of DNS packets |
|
Settings
Access restricted option behaves like enabled on 7912 |
|
7912 can not
initiate hold w/ multiple calls per line and shared lines. |
|
7912-RTP URI
push during call requires user to cycle hook twice to end |
|
7912 dies
when configuring Graphics via TFTP on CCM 4.1 |
|
The browser
window on the 7912 opens when it should not |
|
During cross
upgrade, power off/on the phone & the phone never come up |
|
There is no
dial tone when exiting from the directory menu |
|
7912 Chinese
Locale- Unable to display calling number |
|
CHSWrong
Phone display |
|
Found dtmf
digits fail when calling into Meeting Place IVR. |
|
DTMF when
users mash 7912 keys unrecognizable to AA/IVR |
|
7905/7912-
Does Not Format '?' Characters in Services URL Properly |
|
XML Error
[4]-Parse Error on 7912G when creating FastDial in PAB |
|
Found dtmf
digits fail when calling into Meeting Place IVR. |
4.1-Devpack
17.5 |
|
support for
EM2-HDA-4FXO in CCM |
|
Support for
BRI vics on 26/36/37/38xx |
|
Support for
BRI vics on 26/36/37/38xx |
4.1-Devpack
17.4 |
|
CSV and XML
files for Baker Project should be updated to reflect new fea |
4.1-Devpack
17.3 |
|
CSV and XML
files for Baker Project should be updated to reflect new fea |
4.1-Devpack
17.2 |
|
support for
EM2-HDA-4FXO in CCM |
|
Video
capability for Communicator has to be added |
|
ONLINE HELP-
Ring tone help screen needs to replace Alert with Ring |
|
ONLINE HELP-
Device Configuration help need updated with new submenus |
|
ONLINE HELP-
Help info for editing IP address needs addtional steps |
|
ONLINE HELP-
Erase softkey help under Settings needs more information |
|
ONLINE HELP-
Help for Network Settings DNS Server 1 returns error |
|
No Help
content for the softkey OPickUp. |
|
ONLINE HELP-
Default softkey under some User Preferences returns no help |
|
No Help
content for the softkey OPickUp. |
4.1-Devpack 17 |
On 7970
Display-on-Time shows default value after setting it to blank |
7940/60 (Load -
P00307020200): |
802.1x auth
state remains after PC disconnect |
|
Video stream
not terminated when CM is down Bsphere 2628 |
|
Incorrect
status msg when no ctl on phone and modified ctl dwnld |
|
NetworkConfigurationX
tag names do not match Network Config UI |
|
7960/40 does
not support QueryStringParam as documented in SDK |
|
Help for side
car buttons throw an error |
|
IPSvcssupported
xml fields size are 1 less than max |
|
IPsvcNew http
headers support as per SDK 4.0(1) |
|
Lock icon
overlaps to page title text |
|
Mid-call
video starts when active call is in mute state |
|
Idle
URLRefresh page does not recover after a packet loss |
|
Phone shows
encrypted call with CM 3.3 |
|
Phone accepts
invalid/Reserved/Multicast IP address |
|
Security
Configuration menu name should be separate from title |
|
invalid
display by ip phone on key pad uris push |
|
Clear softkey
doesnt clear interface stats on HTTP page |
|
phone not
updating volume changes during call preservation state |
|
Autodial
fails on choosing hold option for the current call |
|
Handle
current call not displayed on dialing from directories |
|
Not able to
scroll down to see help pages displayed by i button |
|
pressing first line speed dial causes second line to go
offhook. |
|
7940/60 phone
should use HTTP 1.1 for URL with IP address |
|
Auto line
select enabled prevent use of softkeys on 1st line |
|
No PORT_UP
event on 7940 if PCport on Phone changed frm 10Mbps-100Mb |
|
7960 stuck in
booting process when press service before phone alive |
|
phone sends
tftp request to ip address 0.0.0.0 |
|
7960/7940Voice
Quality Degradation With Echo Back To Remote Party |
|
Phone does
not retains Volume Settings changes |
|
Shared line
call doesnt display toggling between lines correctly |
|
7960/40 phone
will not fail back to primary |
|
Support
calloc caller PC broke LA built. |
|
Change in
behavior of resuming the call that is onhold on IP Phone,7.1.2 |
|
Phone
connects to secure SRST if bad config |
|
Clouseau debug infrastructure implementation in 7960 sccp phones. |
|
Retain old BA
while LA upgrade |
|
speaker
button won't work with sidecar |
|
Disable the
display debug tracing by default on 7960 phones |
|
Update
copyright year on mid-range IP Phone boot display |
|
7940/7960
display HTTP error[11] when pressing Services/Directory button |
|
After a
preserved calls is terminated, the phone is stuck |
|
Key rollover
with Hold and EndCall Softkeys causes wrong action |
|
7940/60 stuck
in Configuring CM List state |
4.1-Devpack 16.1 |
TurboError
Extracting File using latest tc-sccp.jar file |
4.1-Devpack 16 |
Known Caveat for 7940/60 phones |
Change in
behavior of resuming the call that is onhold on IP Phone,7.1.2 |
Neanderthal -
Implement JAVA side and QED CM interface |
|
7970/7971 |
|
7970 won't
boot w/ inline power |
|
7905/7912 |
|
TFTP Client
Busy Retry Behavior |
|
7912 doesnt
display correct Softkeys when using MCDN feature |
|
IP Phone 7905
not responding to http commands |
|
7912 cant
ring immediately when receiving a call after fallback |
|
MWI will be
turned off by incoming call |
|
7905/12
display English prompt at Services page |
|
7912 ignores
StationClearPriNotifyMessage from CME |
|
Authentication
delay between IP Phone 7905 and CM 5.0 is to long |
|
Issues with
processing of DNS packets |
|
7912 RTP URI
push during call requires user to cycle hook twice to end |
|
7912 dies
when configuring Graphics via TFTP on CCM 4.1 |
|
During cross
upgrade, power off/on the phone & the phone never come up |
|
Found dtmf
digits fail when calling into Meeting Place IVR. |
|
6608 |
|
Burst of
static during ringback and connect on calls through 6608 |
4.1-Devpack 15 |
7920 |
|
BSSID is all
Zeros in Reassociation Packets |
|
Site Survey
Detail Shows the Same Info for All APs Sometimes |
|
7920 Does Not
Answer IGMP Query |
|
7920 Could
Get Into Continuous Roaming |
|
7920 May Get
1 Way Audio Without ARP-Caching |
|
7920 Will
Sometimes Show RSSI = 1 |
|
Packets are
Sent at 1mbps rate Off Call When 7920 Uses a Non-Auto Rate |
|
7920
Advertises All Rates Are Supported When Non-Auto Rate Is Configured |
|
Get
association timeouts sometimes with Aruba APs |
4.1-Devpack
14.2 |
Neanderthal-Implement
JAVA side and QED CM interface |
|
DevPack does
not install the locale files |
4.1-Devpack 14.1
4.1(3)
compatible
4.1-Devpack 14 |
Support
needed for Ext Device Package execution during ES/SR install |
|
Patch Install
says file replaced successfully whether done or not |
|
Incorrect
devpack version may allow newer devpack to be overwritten |
|
Need to dump
a list of running processes during installation. |
|
SR doesnt
Init Database on replication failure detected scenario |
|
Device
Default is updated when uninstalling ES/SR |
|
7961 device
pack doesnt conatin proper device name on device default |
|
7970/7971 |
|
Some items of
Streaming Statistics from 7970 inconsistant w/ 7960s |
|
Headset
status indicator incorrect after 7970 reboot |
|
7970
incorrect LineType for some line buttons |
|
7970 not auto
answer with headset after restart w/ headset light on |
|
7970 not put
active call in focus after incoming call disconnected |
|
Phone restart
with lower line rate of multicast/broadcast traffic |
|
7970 fails to
reregister after temporary WAN failure |
|
Ringer volume
and other parameters are not configured aftr DSP reset |
|
Sidetone on
handset after reset |
|
7970 ICMP
hard errors behavior changes |
|
7970 does not
pick up the line when configured share line |
|
Extra ring
heard when answering call after adjusting volume |
|
7970
RTPRx/RTPMRx URI syntax error allowed |
|
Possible
deadlock situation in msg queue software |
|
Phone stuck
at Configuring IP after prolonged CCM disconnect/recon |
|
7970 drops
host in DNS queries with subdomains |
|
Skate
Security config menu opt 5 and 6 display wrong softkeys |
|
7970
RTPRx/RTPMRx URI opens invalid port by default |
|
Phone
lockupCSCeg04380 |
|
7970
gethostbyname() does not return multiple IP addresses |
|
Mute signal
heard on network |
|
When
resetting the phone (**#**) PC loses network connectivity |
|
phone freezes
during reboot with mqThread problem |
|
7970 phone
failover to SRST takes more than 6 minutes |
|
Last digit
not displayed when dialing from keypad |
|
JavaException
using Navigate Keypad when call on hold |
|
Phone
continue to stay with Requesting msg, cancel key has no effect |
|
Java
exception when 7970 configed with sidecar but none attached |
|
7970 Phone
hangs on changing existing speed dial from phone (CME) |
|
7970 crash
when access protected URL 2nd time |
|
Onhook
Dialing will not accept * or # as first digit |
|
Core dump of
Sunvm.cnu when web-access is disabled & then enabled |
|
Attempt to
load diagnostic image file causes CNU reset |
|
Onhook
Dialing is available when the phone is not registered |
|
7971
Multicast traffic dest to PC dropped by switch in phone. |
|
RTPTx-Stop
not being executed |
|
7971
Unplugging and plug the ethernet cable, looses VLAN id |
|
Incorrect
time for |
|
7970 drops
keys if pressed too fast |
|
EM logged off
profile keeps CFA icon |
|
Update
handling of init.conf authentication settings |
|
SA
Dereferencing pointer to freed memory in Core/CNU/NetSys/udp.c |
|
SA expression
must be a modifiable lvalue in Core/Apps/cmds/ttrace/ |
|
SA Freeing
pointer to already freed memory in Core/Apps/daemons/DHC |
|
Broken
autosensing on type-2 cabling (BU-3494) |
|
Makaha power
request numbers are wrong |
|
ListenerManager
allows for multiple listener |
|
Memory leak
when press keys in predial |
|
Memory leak
on startup in Call History property |
|
7971 phone
not upgrading load, using device defaults. |
|
Phone reloads
from nmap connect scan |
|
Stream.c
flood reloads phone |
|
Failover fail
on 7971 phone with CM 3.3.4(SR2) |
|
CVTA with
7970 messes up audio caps |
|
Phone stuck
at Updating Software |
|
7970 - does
not report Dest Unreach on sendto() |
|
Ethernet
Disconnected message interferes with display (BU-3572) |
|
EndCall
softkey doesnt work when CM down and other end had hit Hold |
|
7971 Low
power backlight needs to be 14 |
|
7970 - only
retries 4 times after leaseT1 expires |
|
7970 hangs at
config IP after reset |
|
Unexpected
DHCP Renew after Release operation |
|
Shared System
Threads create debugging problems |
|
Cut through
on speaker phone take approx one sec |
|
Line button
becomes useless after try dialing from call history |
|
Timer object
should allow ITimerListeners to disable timerCancelled |
|
7970 phone
does not close the sockets automatically |
|
Mid-call
video starts when active call is on mute |
|
7970
registering with CM when a active call is in place |
|
7971 phone
reset after hold/resume duration |
|
Phone freeze
after the extension mobility duration test was run |
|
7970 hangs
intermittently while attempting EM login/logout |
|
XML parse
error when text object with 4000 chars of text is sent |
|
Multiple
restart from CM causes phone to freeze up |
|
http push may
stop working |
|
Console shows
CONSOLE TOO SLOW! Skipping 0 log files! |
|
Trace does
not include key press information |
|
7971 Phone
ignore vvlan information from switch port |
|
CVTA does not
receive information on calls active when PC plugged in |
|
Phone stuck
after erase operation |
|
7971 does not
comply with 802.3af power specification |
|
Phone can
lose VLAN id with broadcast storms in the network |
|
PC attached
to Phone loses network after multiple phone reload |
|
7971 phone
re-boots when SYNC_RCVD state sttack was run |
|
Enable 802.3x
flow control |
|
7970 plays
loud comfortable noise when using G.729 codec |
|
Can not
accept calls when call history is empty and in focus |
|
7970 change
between daylight and standard time 1 hour too early |
|
Ringer stops
working if press speaker right after adjust ring volume |
|
Phone
restarts exposes memory leak in the CallAgent module |
|
Call Info
gone but voice path remains after brief Ethernet disconnec |
|
Phone does
not take Service URL w/ no label |
|
7971 w/ PC
connected not operate in low power mode using ieee inline |
|
7970 does not
display missed call info after waking the display |
|
Phone stuck
under simClient duration test |
|
7970 not
alllow user to set IP Address Release as No |
|
7970 should
display IP address released |
|
7970 missing
date on console logs, status messages & debug display |
|
7970 Autodial
postpends to dialed # if display name contaions #s |
|
UI issue -
services tab not coming to foreground in push scenario |
|
7971
continuously resets if dot1x configured on switch interface |
|
ServicesChanging
volume while RTPRx - softkey gets stuck at Save |
|
shownet
command in cnush gives wrong output |
|
7971 accepts
untagged packets while on a voice VLAN |
|
AbbrDial
softkey appears on 7970 phone in CM3.x |
|
HTTP Push
requests has successful response, but UI does not display XML |
|
7970 does not
properly reset causing sessions hung in LAST_ACK on CCM |
|
7971 PC port
does not show what is configured |
|
CP-7970 Fails
to Boot up if 'switchport voice vlan dot1p' is configured |
|
Bad voice on
7971 phone with 10% broadcast traffic |
|
Broadcast
traffic throttling rate very low w/ load 69 on 7971 phone |
|
7971 phone
only allows 10M (1%) broadcast traffic send to PC |
|
Phone does
not pass thru all multicast traffic to PC |
|
7971 switch
port stops transmitting frames causing phone to unregister |
|
Network
Statistics does not display Port 1 or Port 2 status information |
|
7971 - PPU
workaround does not set forced link speed correctly |
|
7971 - change
CDP from a mgmt packet to a mcast packet in ATU |
|
7971 - enable
VLAN 1 and VLAN 0 |
|
Phone crashed
with in half an hour ,when XML boundary objects script was |
|
Phone crashes
for 200 calls per device case |
4.1-Devpack 13 |
Add QED
support for 7911 |
|
Add 7985 QED
support CCM versions 4.X and 5.X |
|
6624 |
|
6624 FXS port
is unavalable for 2 mins after disabling and enabling |
|
updation on 6624 does not reflect on port configuration
page. |
|
FAC tone
played continuously on using non default network locale |
|
6608/6624 |
|
Integrate
4.3.25 DSP firmware for 6608 |
|
6608 |
|
DicktracyRemove
unnecessary DSP and MLPP related messages. |
|
6608-Dicktracy
- Reduce trunk flash timer from 700ms to 400ms. |
4.1-Devpack 12 |
7935 |
|
7935 reboots
on its own and couldnt reach tftp server thereafter. |
|
7935/7936 |
|
7935
Autonegotiation does not work |
|
CCME 7936
conference call one way speech path and 7936 reboots |
|
7935 and 7936
stops ringing when 2 parties call it simultaneously |
|
7936/7935
does not support JOIN feature of CCM 4.0 |
|
Ringer stops
during incoming call when dial pressed under corp |
|
7935 is not
accepting cass B netmask, if Ip addr is class C |
|
Inconsistent
LCd and web page display |
|
On first call
from 7935 gets one-way voice |
|
7935/7936
marking |
|
7935 will not
register to ccm |
|
7936 will not
register to ccm |
|
MOH is not
heard during Transfer |
|
Not able to
configure admin vlan via web interface. |
4.1-Devpack 11 |
7940/60 |
|
Remove vender
specific parameter edit softkey from IP Phones |
|
Build phone
loads |
|
Edit Dial
push uris show Directories icon |
|
Unable to
answer the call with linekey with shared lines |
|
14th digit
disapears from IP Ph CFA Display after device reset |
|
Active call
moves to the top of list after 9 seconds |
|
7960
Directories button sometimes opens Services URL |
|
7960 not
showing correct display when same DN config on multiple lin |
|
Phones To Be
More Ambitious Towards Updating Firmware |
|
Phone web
page not accessible after socket stress was run |
|
Cannot load
diag image to 7940/7960 phone |
|
Cannot use #
or * as first entry while onhook |
|
7960 should
not automatically return to detail view from overview |
|
With multiple
held calls, line key should not resume oldest call |
|
With single
on-hold call, line button should invoke overview display |
|
Help for side
car buttons throw an error |
|
CallManager
TFTP Load=6.0(5)0 File Not Found when phone is reset |
|
Phone stuck
in Configuring IP when Factory Reset, save settings dhcp |
|
LA loader
must check new LA size before burning to flash |
|
7960 crashes
during XML POST with IPPhoneExecute |
|
Garbage help
text at a certain key sequence |
|
An error at a
certain key sequence |
|
Selecting
directory entry with keypad doesnt update display |
|
7960 stops
call timer when the CCM down |
|
Key rollover
broken/missing digits when dialling |
|
Wrong
association of 7940/60 help |
|
http//<phone> |
|
unable to answer 2nd line when speaker phone is disabled. |
|
7960 will not
stay registered if ringlist.xml has invalid syntax |
|
Time display
not updated on certain phone menus |
|
Changing
Phone port # causes 7960s in Auth mode not to register |
|
C3PO Frame
Buffer overflow causes COS3 packet drop |
|
IPSvcs-In
case of missing refresh URL, dont show update softkey |
|
Extend scope
of Msg/Dir URL to support icon menu |
|
IP Phones
fails to recieve Audio Multicast Stream and gets reset |
|
Phone unable
to get Ringlist.xml using Alternate TFTP |
|
Audio cut
through delay during Call Waiting Answer |
|
RTP URI push
during call requires user to cycle hook twice to end |
|
Cisco
7940/7960 One-way audio and Freeze or Reset |
|
7940/60 DHCP
Option 60 data different between big and little app |
|
URI SoftKey
Dial resets the phone |
4.1-Devpack 10 |
Makaha needs
to be added to 4.0 and 4.1 branches |
|
7902/05/12 |
|
7912 unable
to be registered when User Locale is Japanese |
|
CP-7912G/7905G
does not add 802.1p tag when no vlan is configured. |
|
7905 and 7912
phones reboot with keep-conference feature |
|
OPickUp
softkey does not work on 7912/7905 |
|
Multiple
Calls on Dir Num calls were disconnected by CMs failover |
|
7905 phone
web server sends data in wrong HTTP version |
|
Select
softkey in phrase 609 and 178 should be defined properly |
|
7912 and 7905
may crash and fail on re-registering |
|
Phone does
not accept DHCP ACK sent to the broadcast address |
4.1-Devpack 09.1 |
Phone Config
lacks precedence by MIC for 7970 phones |
4.1-Devpack 09 |
Due to CSCeg77085 |
The 7940/60
default loads are not being set |
4.1-Devpack
08.2 |
7971 Device
Devpack for CCM 4.0(2)sr1a has missing GUI |
4.1-Devpack
08.1 |
Device
Protocol Options (T1-CAS/PRI) needed for VIC2-xMFT-T1 |
|
PI6 based
features commit to CCM branches |
4.1-Devpack
08 |
7971 phone
icon missing from CM Admin page |
|
7971 device
type and load need to be added to CM releases |
4.1-Devpack 07.1 |
4.1(2)
install adds device type for 7961 phone |
4.1-Devpack 07 |
7970/7971
display instance file and IP Phone Rules xml files wrong |
|
6608 |
|
6608 Fax
Relay debugs in D00404 firmware need to be same as D00403 |
|
6608 inbound
call mistaken for hookflash |
|
6608 Support
for T1 CAS Guard time |
4.1-Devpack 06.2 |
Wrong
WS-X6608 DSP load included with device load in 4.0(2a)SR1 |
4.1-Devpack 06 |
7905/7912 |
|
Switching
back and forth between 2 calls makes the display disappear |
|
Unable to
switch between two active calls on 7912 |
|
ephone-template
on 7912 removes message softkey |
|
7912 and 7905
may crash and fail on re-registering |
4.1-Devpack
05 |
6608 inbound
call mistaken for hookflash |
|
7940/60 |
|
CallInfo CLI
output not correct for different locale file |
|
7960 shared
line predialled digits keep ringing, call ansd on 7970 |
|
Ip Phone
doesnt accept option 66 with trailing dot in hostname |
|
Devices
attached to phone lose network when PC VLAN enabled |
|
7960 does not
display CallInfo if CCM down while in the call |
|
Unable to
access protected URL from menu using custom softkey |
|
IP Phone
recognize dialed number in wrong order |
|
Display shows
only first 23 digits of a 24 digit DN |
|
Dial keys do
not respond for 10 secs after pressing **# |
|
The link http/ |
|
Phone doesnt
display the DN to be edited when editdial is pressed |
|
Loader may
fail - Application Invalid |
|
Phone should
not cache failed credentials |
|
Phone may
stop communicate with CCM or CAPF when using TLS |
|
7960
registered to CM 3.3 shows only one line while call on hold |
|
Edit Dial on
cancel shows Host Not Found |
|
AD Phone
search always has word dial appended |
|
Extra ring
heard when answering call after adjusting volume |
|
Called Party
name is wrong when call is forwarded over ICT |
|
AutoDial
Fails in a Active Call beetween IP Phone and MGCP Endpoint |
|
I-Button
doesnt give any Help for Ring Type Select/Default/Exit |
|
7960 struck
with Booting Dsp alarm on its display |
|
Echo fades in
and out when talking IP phone to IP phone |
|
7940/7960 IP
phones showing as untrusted on Cat3550,3560&4500 |
|
Phone fails
to come up when wrong load Id is mentioned on phone page |
|
Failback
during cert gen not behaving properly |
4.1-Devpack 04 - skipped
4.1-Devpack 03 |
New 6608
modules will not register as a conference bridge or MTP |
|
7970 |
|
7970 not put
active call in focus after incoming call disconnected |
|
Incorrect
time for |
|
7970 drops
keys if pressed too fast |
|
6608 T1/E1 |
|
Negative
value for 6608 counter Total Rx RTP Lost Pkts |
|
6608 T1 CAS
HookFlash is detected in |
|
6608 T1 CAS
Glare Recovery may not work correctly |
|
configurable
non-linear comfort noise attenuation for 6608 |
|
6608 does not
send RSIP forced to CCM when a reset comes from CCM |
|
6608 T1 CAS Disconnect Procedure Enhancements |
|
6608 T1 cas
gateway fails to clear line for unallocated numbers |
|
Reverted to 6.0(1)sr1 due to CSCeg24131 |
|
4.1-Devpack 02.1 |
Remove the
extra are-you-sure from the ES/SR installs |
|
Uninstall
Confirmation dialog should mention version reverting to |
4.1-Devpack 02 |
Cisco 2801 GW
icon missing in Find and List GW page. |
|
7970 |
|
7970
incorrect behavior when try to dial from dir with call on line |
|
7970 Override
Auto Answer if Speaker Disable False doesnt work |
|
7970 Phone
stops accepting HTTP connections |
|
MUTE Call
Stat still shows Sender Packets incrementing mute is on |
|
7970 dynamic
call forward icon not updated properly after login |
|
Double
selection of same ringer deselect it, also display problems |
|
7970 Problems
with ringer selections |
|
Ringing could
not be stopped when call disconnected from far end |
|
Jitter
Tolerance new field added are not saved in conf file |
|
Receiving
default config file does default previous cfg parameters |
|
7970 Does not
translate Australian Daylight Savings correctly |
|
TFTP Server
address gone after Enabling DHCP w/Alternate |
|
7970 lists
Load File as term70.default. User doesnt know load name. |
|
No way to
view call data on another line without answering call |
|
7970 Web page
doesnt display network statistic info correctly |
|
Touching
screen to wake up screen saver often invokes a soft key |
|
Phone Resets
swtiching from Services->Settings after loading images |
|
Erase in
Security Configuration menu only erases one item |
|
Redirected
Authentication URL does not work |
|
Lifting
handset in EditDial calls unedited number |
|
7970 doesnot
failback from SRST when trying to make call |
|
Cannot open,
close, reopen PC/SW Port Config |
|
7970 boot
hangs with unrecognized timezone name |
|
7970 does not
obey StationSetMicroModeMessage (mute microphone) |
|
CP-7970 does
not populate CallingPartyName in Missed Calls Field |
|
CP-7970 Time
get out of sync if not used for extended period |
|
DEvice Config
submenus donot have lock/unlock icon |
|
No alarms or
phone logs when 2 of 4 locale files not found |
|
With 6 calls,
resuming first causes 5th duration overwritten by 6th |
|
Pressing
NewCall, EndCall with 7 calls on hold leaves no call hilite |
|
call timer
for barged call incorrect |
|
Add help for
Call Agent Menu 1161 |
|
Add help for
HTTP Menu 1162 |
|
Add help for
Locale Menu 1163 |
|
Add help for
Power Save Menu (1164) |
|
Add help for
Ethernet Menu (1165) |
|
Add help for
Media Menu (1166) |
|
Add help for
QoS Menu (1167) |
|
Add help for
UI Menu (1168) |
|
Add help for
Span PC Port (1169) |
|
Update path
to admin tasks in online help |
|
DHCP gets
hung on boot |
|
DHCP disable
and CTL Erase enables DHCP |
|
GARP and
VVLAN enable and disable reversed on display |
|
CTLFile stays
unlocked still after re-dhcp |
|
7970 not able
to save downloaded background image |
|
file auth
error after factory reset |
|
Barge
functionality not working for shared line between 7960 & 7970 |
|
7970 displays
Mid-Atlantic time zone incorrect |
|
Default
string is used as both softkey and parameter value |
|
HTTP request
do not work on 7970, different from 7960/40 |
|
7970 stops
sending CDP to attached Cisco VT Advantage PC |
|
7970 does not
notice media disconnect when CVTA PC unplugs |
|
7970 Wont
Register after upgrade to 3.3.4 |
|
7970 displays
incorrect softkey sets when a call barged in |
|
RUS Line text
label shows garbage on 7970 IP Phone |
|
Extension
Mobility in 7970 shows English in all locales |
|
7970 hangs on
request of LineInfo |
|
Erase softkey
missing on Network Config menu |
|
7970 does not
properly interpret parameter E |
|
7970 running
6.0.1 load does not show remote in use on shared line |
|
XML services
returned NullPointerException |
|
7970
continues to ring after call is disconnected |
|
PC behind the
phone cannot authenticate into the network with 802.1x |
|
7970 displays
NZ ( |
|
7970
CiscoIPPhoneInput Softkey gone if there is expire header in asp |
|
XML post to
7970 using @ in password resets phone |
|
7970 phones
query DNS instead of using proxy address for services |
|
7970 phones
query DNS instead of using proxy address for services |
|
7970 voice
quality degrade with UDP broadcast traffic. |
|
7970 shared
line with out Barge causes phone to display incorrectly |
|
One second
refreshing of CiscoIPPhoneImageFile objects fails |
|
When in
refresh XSI loop, hitting cancel does not cancel the request |
|
7970 does not
display Registration Rejected messages |
|
Softkeys
disappear after cancle of callback on a held call |
|
7970 sends a
5-msec packet before a type13 packet (Hurt Confer. Brdg |
|
7970
unregisters after unplugging PC from PC port |
|
7970 Has no
serviceability to retain stack traces after initialize |
|
7960 Call
Info display behavior inconsistant |
|
TCP SYN
vulnerability and Cisco phone end points |
|
Execute URL
on 7970 is doing a DNS lookup |
|
7970 does not
queue URLs from CiscoIPPhoneExecute |
|
Disable
speaker does not work |
|
Pressing line
button for active call doesnt go to overview screen |
|
7970 causes
continuous popping noise in a MCU conference (VAD=1) |
|
7970 display
/ softkeys will freeze with high incoming call traffic |
|
7970 display
/ softkeys will freeze with high incoming call traffic |
|
7970 Select
key is not greyed out on Ring menu |
|
7970 still
display IPMA manager watch window after switch CCM |
|
7970 resets
on pressing **#** while on corporate directory screen |
|
Http request
http/phones IP/CGI/LineInfo resets the phone |
|
7970 failed
to recover from DSP error - DSP stopped by assertion |
|
7970 added
code to dump DSP message when its reponse faied to return |
|
7970 will not
allow a CVTA CAST connection |
|
Config file
hunt on all tftp servers |
|
7970 stops
accept HTTP after incorrect PUSH message |
|
7970
advertises wrong platform - CP-7 |
|
HTTP headers
are case sensitive |
|
7970 not
answering calls while in a menu |
|
7970 resets
when accessing Network Statistics via web interface |
|
Date Time
Group=Local time zone wrong in 7970 |
|
7970 If QRT
key is pressed during active call softkeys disappear |
|
Vendor String
Inconsistant - 7970 |
|
Parche phone
cannot upgrade when config file has secure SRST |
|
GARP is
enabled in CM but showing GARP Enabled Yes on the phone |
|
Exit key not
work when Dial from Directory on active line |
|
Skate 7970
not accepting untagged packets |
|
Incoming call
droped if Dial from Directories |
|
7970 shows
wrong softkey sets w/ Callback and incoming call |
|
7970 does not
close CallBack application after dial from CallBack |
|
7970 DHCP
timer changed to 10 seconds |
|
7970 Phone
ServicesURL handling disparity between 7970 and 7960 |
|
7970 UI
freeze up under stress test |
|
Accessing web
page in 7970 causes crash - possibly auth. problem |
|
CP-7970 has
worng values on XML config |
|
Pressing
Services button causes phone to fail |
|
Phones stuck
in Configuring IP after reset |
|
Soft resets
freeze phone - memory leak |
|
Soft
resetting causes flash memory error |
|
7970 should
not make new call pressing line button w/ callback |
|
7970 shows
CCM Down after restart from CCM w/ Active call |
|
Unable to
answer call with help menu active unless Answer is pressed |
|
Phone
processing SIGIPCFG before phone app loaded |
|
7970 display
error on Brightness menu after answer call |
|
7970 not auto
answer with headset after restart w/ headset light on |
|
7970 display
error in Hold/Resume stress test |
|
7970 doesnt
respond to Reset when shared line has Remote-In-Use call |
|
Predial does
not work when using offhook, line key, or speaker |
|
7970 crash w/
calls on 3 lines |
|
Skate SCCP
messages cause phone to crash |
|
CNU doesnt
reboot after 4 consecutive resets |
|
7970 does not
take changes to DSCP for SCCP phone config field |
|
7970 phones
unregister with Missing keepalives |
|
7970 lost
registration to CCM during Hold/Resume duration test |
|
7970 timer
thread cause 100% CPU usage leading to reset |
|
7970 displays
blank/empty pages when receiving IPPhoneStatus request |
|
Incorrect
time for the Australian time zone AEST |
|
Java.lang.NullPoinerException
while 7970 fail over |
|
7970G will
not upgrade to newer load unless power-cycle |
|
Memory Leak
on Restarts when there have been calls |
|
Null Pointer
Exceptions when calls ended that are not visible |
|
Init
AppStatus URI does not work and causes an exception |
|
7970 hangs
randomly, requires reset. |
|
7970 stuck in
unregistered state if network down w/ 150 held calls |
|
Screen on
7970 phone got overwritten by page that has refresh timer |
|
7970 locks up
on boot up with failed assert (pos <= t->maxPos) |
|
7970G -
Pushing xml obj with long tags resulted in Phone reboot. |
|
7970 becomes
inoperable after firmware upgrade attempt |
|
7970 phone
got resetted when user hit setting key |
|
7970 Sending
http request to the phone freezes it |
|
CP-7970G -
SELECT function works on touchscreen / not softkey |
|
7970 fails to
reregister after temporary WAN failure |
|
Input of
softkeys/linekeys/navkeys not shed if too high of rate |
|
CDP exits
during link flap test |
|
CNU doesnt
restart the VM when it exits |
|
7970 DSP
reset due to libMTdoorCall select timeout |
|
Calls up when
CCM connection is lost are not avail for reuse |
|
7970 can not
boot after upgrade/downgrade stress test |
|
JVM not shut
down properly when OS reboots due to rapid resets |
|
Need to
increase size of syslog files to provide more debug data |
|
Exceptions in
the ITimerListener Dispatcher starves ObjectPool |
|
There is no
way to determine the DHCP/CDP state from the GUI |
|
7970 hang
after idle a while |
|
Memory Leak
when Entering Menus |
|
nformation
message displayed continuously on console |
|
7970 crash
after Erase config several times |
|
DSP process
signal traps (killed)-> doorCall select timeout |
|
When
java.lang.OutOfMemoryError, init doesnt restart VM |
|
Can only
answer call via Answer softkey after handle call failure |
|
7970 has
resize error during stress test |
|
7970 phone
freezes when the XML objects are pushed |
|
7970 displays
HI ( |
|
No packet
sent when Silence suppression is turned on |
|
7970 displays
empty callback page with no softkey |
|
In some
Interfaces there is a potential for ObjectPool leaks |
|
# key
displays error insted of its character set i.e. # + $ et al. |
|
Message
button becomes inactive after config message URL |
|
7970 - CDP
can not acquire VLAN info |
|
RMS FULL
Exception has no handler |
|
7970 sending
wrong security capabilities to SRST |
|
7970 Hearing
white noise when using codec g729 |
|
7970 Hangs on
reset from CCM |
|
Phone freezes
when a XML object is pushed and exit is pressed for 6 |
|
Phone in
requesting loop when XML objects are pushed sixth time |
|
7970 cannot
parse non-URL proxy server address |
|
7970 doesnt
mark services and HTTP packets correctly |
|
7970 stuck in
Configuring IP when erase CTL with DHCP disabled |
|
7970 - DNS
does not return from select errors |
|
Phone freezes
during upgrading test with REL signed image |
|
7970 stops at
Configuring IP after its config erased |
|
XsiDirectory
Response causes memory leak |
|
7970 has
Segmentation fault with its CCM switchport flap |
|
Wrong
Security Icons shown for 7970 Phones in SRST mode. |
|
CiscoIPPhoneStatus
object leaks graphic resources |
|
Hashtable.get()
is returning an invalid Exception |
|
Phone
continue to stay with Requesting msg, cancel key has no effect |
|
No Audio
& call is dropped for a G729 7970 call after CM Restart |
|
Default keys
shown while using custom keys |
|
Services
Prompt line not cleared if new page has no prompt |
|
Multiple
timezones are incorrect |
|
7902 |
|
Hold lamp of
CP-7902G is not turned on during Transfer in SRST mode. |
|
7902/05/12 |
|
Setting/Web
access cannot be changed in different network |
|
7905/12 |
|
HUN - KATE
file for 7905 does not display required chars |
|
HUN time on
the phone display is not showing in Hungarian |
|
Can not pick
up the latter reached call on 7912s shared line. |
|
7912 will not
fallback from SRST to CCM when the CCM is back online |
|
7912 Delayed
Dial tone, Retransmit time |
|
7912/7905 do
not implement the RTPMRx URI correctly |
|
Wrong
CallInfo Display in CME environment |
|
7912G
Japanese locale not working for Extension Mobility login/out |
|
add OPickup
for CCM 4.1(2) |
|
Display
English Acct softkey in |
|
Missing
dialed number after pressing service button |
|
7905XML
Encode URL which is already encoded in some cases |
|
CP-7912G support controlling DSCP marking for voice bearer. |
|
7905/7912
should save setting/web access config |
|
CP-7912G does
not control layer2 CoS value for skinny and RTP packet |
|
Ext Mobility
does not work for some dev profiles on 7912 & 7905 |
|
6608 |
|
configurable
non-linear comfort noise attenuation for 6608 |
4.1-Devpack 01 |
Giove CCM QED
checkin - initial commit |
|
For removing
1880 from the CCM branches |
These Device
Package release notes contain important information about installation
procedures and resolved caveats for Cisco Unified CallManager Device Package
Note: Before you install this Cisco Unified
CallManager Device Package, Cisco recommends that you review the “Important
Notes” section for information about issues that may affect your
system.
For optimal performance, be sure
that you use the Cisco IP Telephony Locale Installer that is specific to the
version of Cisco Unified CallManager that you use. Be aware that all phrases may not display in
the desired locale when you upgrade to a different version of Cisco Unified
CallManager. Refer to the readme file
that is posted with the Cisco IP Telephony Locale Installer software on the
following URL for the complete list of supported languages: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/locinst/index.htm.
Each release of Cisco Unified
CallManager may support a different number of locales. The full suite of Locale
Installers that work with each applicable version of Cisco Unified CallManager
can be found on http://www.cisco.com
after the English version becomes available. You can download the Locale
Installers for all languages that are supported with Cisco CallManager from the
following location: http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml.
Note: When using locales, Cisco
recommends that you wait until the locale installer that specifically supports
the version of Cisco Unified CallManager that you use becomes available before
you upgrade your system. Because some
incompatibilities may exist between releases, be sure to only use the locale
installer that specifically supports your version of Cisco Unified CallManager.
Obtaining Documentation
Cisco documentation and additional
literature are available on Cisco.com. Cisco also provides several ways to
obtain technical assistance and other technical resources. These sections
explain how to obtain technical information from Cisco Systems.
Cisco.com
You can access the most current
Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at
this URL:
You can access international Cisco
websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
For
additional information about Cisco Unified CallManager, refer to the following
documentation:
To access
the documentation suite for voice products, navigate to the following URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/.
To access
the latest software upgrades and related documentation for
Cisco Unified CallManager, navigate to the following URL and then choose the
applicable version: http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml.
Cisco
documentation and additional literature are available in a Documentation DVD
package, which may have shipped with your product. The Documentation DVD is
updated regularly and may be more current than printed documentation. The
Documentation DVD package is available as a single unit.
Registered
Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD
(product number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
Cisco
Ordering tool:
http://www.cisco.com/en/US/partner/ordering/
Cisco
Marketplace:
http://www.cisco.com/go/marketplace/
You can find instructions for
ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in
these ways:
Documentation Feedback
You can send comments about technical
documentation to bug-doc@cisco.com.
You can submit comments by using the
response card (if present) behind the front cover of your document or by
writing to the following address:
Cisco Systems
Attn: Customer Document Ordering
We appreciate your comments.
Cisco Product Security Overview
Cisco provides a free online
Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform
these tasks:
A current list of security
advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt
If you prefer to see advisories and
notices as they are updated in real time, you can access a Product Security
Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this
URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Cisco
is committed to delivering secure products. We test our products internally
before we release them, and we strive to correct all vulnerabilities quickly.
If you think that you might have identified a vulnerability
in a Cisco product, contact PSIRT:
We
encourage you to use Pretty Good Privacy (PGP) or a compatible product to
encrypt any sensitive information that you send to Cisco. PSIRT can work from
encrypted information that is compatible with PGP versions 2.x through
8.x. Never use a revoked or an expired
encryption key. The correct public key to use in your correspondence with PSIRT
is the one that has the most recent creation date in this public key server
list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In
an emergency, you can also reach PSIRT by telephone:
Obtaining Technical Assistance
For all customers, partners,
resellers, and distributors who hold valid Cisco service contracts, Cisco
Technical Support provides 24-hour-a-day, award-winning technical assistance.
The Cisco Technical Support Website on Cisco.com features extensive online
support resources. In addition, Cisco Technical Assistance Center (TAC)
engineers provide telephone support. If you do not hold a valid Cisco service
contract, contact your reseller.
The Cisco Technical Support Website
provides online documents and tools for troubleshooting and resolving technical
issues with Cisco products and technologies. The website is available 24 hours
a day, 365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco
Technical Support Website requires a Cisco.com user ID and password. If you
have a valid service contract but do not have a user ID or password, you can
register at this URL: http://tools.cisco.com/RPF/register/register.do
Note:
Use the Cisco Product Identification (CPI) tool to
locate your product serial number before submitting a web or phone request for
service. You can access the CPI tool from the Cisco Technical Support Website
by clicking the Tools & Resources link under Documentation & Tools.
Choose Cisco Product Identification Tool from the Alphabetical Index drop-down
list, or click the Cisco Product Identification Tool link under Alerts &
RMAs. The CPI tool offers three search options: by product ID or model name; by
tree view; or for certain products, by copying and pasting show command output.
Search results show an illustration of your product with the serial number
label location highlighted. Locate the serial number label on your product and
record the information before placing a service call.
Using the online TAC Service Request
Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service
requests are those in which your network is minimally impaired or for which you
require product information.) After you describe your situation, the TAC
Service Request Tool provides recommended solutions. If your issue is not
resolved using the recommended resources, your service request is assigned to a
Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service
requests or if you do not have Internet access, contact the Cisco TAC by
telephone. (S1 or S2 service requests are those in which your production network
is down or severely degraded.) Cisco TAC engineers are assigned immediately to
S1 and S2 service requests to help keep your business operations running
smoothly.
To open a service request by
telephone, use one of the following numbers:
Asia-Pacific:
+61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704
55 55
USA: 1 800
553-2447
For a complete list of Cisco TAC
contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests
are reported in a standard format, Cisco has established severity definitions.
Severity 1 (S1)—Your network is “down,” or there is a critical
impact to your business operations. You and Cisco will commit all necessary
resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of
an existing network is severely degraded, or significant aspects of your
business operation are negatively affected by inadequate performance of Cisco
products. You and Cisco will commit full-time resources during normal business
hours to resolve the situation.
Severity 3 (S3)—Operational
performance of your network is impaired, but most business operations remain
functional. You and Cisco will commit resources during normal business hours to
restore service to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product
capabilities, installation, or configuration. There is little or no effect on
your business operations.
Obtaining Additional Publications
and Information
Information about Cisco products,
technologies, and network solutions is available from various online and
printed sources.
·
Cisco Marketplace provides a variety of Cisco books,
reference guides, and logo merchandise. Visit Cisco Marketplace, the company
store, at this URL: http://www.cisco.com/go/marketplace/
·
Cisco Press publishes a wide range of general networking, training and
certification titles. Both new and experienced users will benefit from these
publications. For current Cisco Press titles and other information, go to Cisco
Press at this URL: http://www.ciscopress.com/
·
Packet magazine is the Cisco Systems technical user magazine for maximizing
Internet and networking investments. Each quarter, Packet delivers coverage of
the latest industry trends, technology breakthroughs, and Cisco products and
solutions, as well as network deployment and troubleshooting tips,
configuration examples, customer case studies, certification and training
information, and links to scores of in-depth online resources. You can access Packet
magazine at this URL: http://www.cisco.com/packet
·
iQ Magazine is the quarterly publication from Cisco Systems designed to help
growing companies learn how they can use technology to increase revenue,
streamline their business, and expand services. The publication identifies the
challenges facing these companies and the technologies to help solve them,
using real-world case studies and business strategies to help readers make
sound technology investment decisions. You can access iQ
Magazine at this URL: http://www.cisco.com/go/iqmagazine
·
Internet Protocol Journal is a quarterly journal published by Cisco Systems for
engineering professionals involved in designing, developing, and operating
public and private internets and intranets. You can access the Internet
Protocol Journal at this URL: http://www.cisco.com/ipj
·
World-class networking training is available from
Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html
CCSP, the Cisco Square Bridge logo,
Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.;
Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service
marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX,
Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified
Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems
Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet
Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step,
FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ
Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys,
MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar,
Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare,
SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way
to Increase Your Internet Quotient, TransPath, and VCO are registered
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States
and certain other countries.
All other trademarks mentioned in
this document or Website are the property of their
respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (0501R)
Copyright © 2009 Cisco Systems, Inc.
All rights reserved.