The firmware image within the installation program is named CP7926G-1.4.4.3.LOADS and supports the Skinny Client Control Protocol (SCCP) for the Cisco Unified Wireless IP Phone 7926G.
This firmware version is supported on Cisco Unified Communications Manager (CUCM) Release 7.1(5) and later, and Cisco Unified Communications Manager Express (CUCME) Release 8.6 and later.
Release Notes for this and other firmware versions are
available at the following URL:
http://www.cisco.com/en/US/products/hw/phones/ps379/prod_release_notes_list.html
1. Click the following URL: http://www.cisco.com/cisco/software/navigator.html?mdfid=269065653.
2. In the Find Device box, enter 7926 and click the Go button.
3. Click the Cisco Unified Wireless IP Phone 7926G highlighted link.
4. Click the Skinny Client Control Protocol (SCCP) Software link.
5. To view all available versions, click Expand all.
6. Select and click the current software version.
7. Download to your
hard drive the proper Cisco 7926 firmware installer for your Cisco Unified
Communications Manager version, as shown in Table 1.
Please note that different versions of the Cisco 7926 firmware installer are
needed for different Cisco Unified Communications Manager releases.
Table 1: Cisco Unified Wireless IP Phone Model 7926G Firmware Installer
CUCM Release
Cisco 7926 Firmware Installer
MD5 Hash
7.1(5) and later
cmterm-7926-sccp.1-4-4-3.cop.sgn
2d:de:1f:42:79:9d:23:2b:c9:fe:5c:a8:01:4d:09:80
Express 8.6 and later
cmterm-7926-sccp.1-4-4-3.zip
36:f1:2c:a3:bc:ba:c1:8b:d3:cc:cf:4f:1c:45:be:18
8. Install the firmware according to your Cisco Unified Communications Manager release.
Cisco Unified Communications Manager (formerly Cisco Unified CallManager) Version 7.1(5) and later
1. Using your web browser, log in to the Cisco Unified OS
Administration web page.
2.
Under the Software Upgrades menu, select Install/Upgrade.
3. In
the Software Location section, fill in the appropriate values for the
file that you downloaded above, and click Next.
4. In the Available Software drop-down box, select the file you downloaded above, and click Next.
Note: In CUCM 6.0 and later, the drop-down box
is referred to as Options/Upgrades.
5.
After validating that the MD5 hash value is correct, click Next.
6. In
the Warning box, verify that you have selected the correct file and then click Install.
7.
Verify that the installation status is Complete.
8. To install another file, click Install Another and repeat steps 3 - 7.
9. Restart the TFTP server
a. From the Navigation drop-down
menu, select Cisco Unified Serviceability and click Go.
b. Under the Tools menu, select Control
Center - Feature Services.
c. In the Server drop-down box,
select the server where the firmware was installed.
d. Click the Cisco Tftp service
radio button.
e. Click the Restart button or
icon.
10.
Reset the Cisco Unified Wireless IP Phone 7926G to upgrade the firmware.
a. From the Navigation drop-down menu, select Cisco
Unified CM Administration and click Go.
b. Under Device menu, select Phone.
c. Click Find to list all the devices.
d. Select the Cisco 7926 wireless IP phones to reset, then
click Reset Selected button or icon.
e. In the Device Reset pop-up window, click Reset.
Cisco Unified Communications Manager Express Version 8.6 and later
1. Extract files from the ZIP image and manually copy them to TFTP server (router flash), and enable them for TFTP.
Example below:
tftp-server flash:CP7926G-1.4.4.3.LOADS
tftp-server flash:APPSS-1.4.4.3.SBN
tftp-server flash:GUIS-1.4.4.3.SBN
tftp-server flash:JSYSS-1.4.4.3.SBN
tftp-server flash:JUIS-1.4.4.3.SBN
tftp-server flash:SYSS-1.4.4.3.SBN
tftp-server flash:TNUXS-1.4.4.3.SBN
tftp-server flash:TNUXRS-1.4.4.3.SBN
tftp-server flash:WLANS-1.4.4.3.SBN
tftp-server flash: EA15FW-BF3-220.SBN
!
telephony-service
load 7926 CP7926G-1.4.4.3.LOADS
2. For the 7926G
device type, set the load type to CP7926G-1.4.4.3.LOADS.
3. Reset the Cisco
Unified Wireless IP Phone 7926G to upgrade the firmware.
For more information
about this procedure, refer to the Installing and Upgrading Cisco Unified
CME Software at following URL:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeinstl.html
You may verify the installation of the firmware as follows:
Cisco Unified Communications Manager (formerly Cisco Unified CallManager) Version 7.1(5) and later
1. Using your web browser, log in to the Cisco Unified CM
Administration web page.
2. Under the Device
menu, select Device Settings > Device Defaults.
3. Verify that the
new firmware image name is listed in the Load Information field for the
Cisco 7926 SCCP wireless IP phone.
Cisco Unified Communications Manager Express Version 8.6 and later
1. Use the show flash command to learn the filenames associated
with the Cisco 7926 SCCP wireless IP phone firmware.
2. Use the show
ephone phone-load command to verify that the Cisco 7926 SCCP wireless IP
phone firmware that is installed on a particular ephone.
The Cisco Unified Wireless IP Phone 7926G firmware can
be upgraded without a Cisco Unified Communications Manager,
using a USB connection or WLAN. Follow the instructions below to upgrade
your phone firmware using a USB
or WLAN connection.
File Name |
MD5 Hash |
CP7926G-1.4.4.3.TAR |
f3:b2:d2:e7:74:57:f6:6f:bb:ea:6d:6e:34:5a:31:88 |
· Windows 2000 or XP 32 bit = USB-Install-792x-Windows2000XP-32bit.1-0-4.exe
· Windows 7 32 bit = USB-Install-792x-Windows7-32bit.1-0-4.exe
· Windows 7 64 bit = USB-Install-792x-Windows7-64bit.1-0-4.exe
8. In the Release Information row, click the Readme link to download the installation instructions and follow them to install the Cisco Unified Wireless IP Phone 7921G, 7925G, 7925G-EX, and 7926G USB driver.
File Name |
MD5 Hash |
7926CU-1.3.1.AVA |
7a:73:25:66:0f:9a:75:9d:5d:5f:30:8b:34:40:5d:4d |
© 2013 Cisco Systems, Inc. All Rights Reserved