Cisco Unified CallManager Release 4.1(3) Service Release 7
Release Notes Version 1
April 22, 2008
Table of Contents
Resolved
Caveats for Cisco Unified CallManager 4.1(3)SR7
File
Versions included in 4.1(3)SR7
Firmware
Versions included in 4.1(3)SR7
Determining
the Software Version
Compatibility
Matrix and Supported Upgrades
Locale
Installer for Cisco Unified CallManager
Obtaining
Documentation, Obtaining Support, and Security Guidelines
Cisco
Product Security Overview
Obtaining
Technical Assistance
These Service Release (SR) release notes contain important information about installation procedures and resolved caveats for Cisco Unified CallManager release 4.1(3)SR7. Updates for these release notes occur with every Cisco Unified CallManager SR.
Note: Please review all sections in this document pertaining to installation before you install this Service Release. Failure to install this Service Release as described may result in inconsistent Cisco Unified CallManager behavior.
Make sure that you install and configure this release of Cisco Unified CallManager on a Cisco Media Convergence Server (MCS).
You must
install Cisco Unified CallManager on a Cisco-approved HP server configuration
or on a Cisco-approved IBM server configuration, as indicated here:
http://www.cisco.com/en/US/products/hw/voiceapp/ps378/prod_brochure_list.html
This Service Release is a cumulative update that incorporates all of the fixes and changes from Cisco Unified CallManager 4.1(3) ES135, along with additional changes that are specific to this Service Release.
Note: Service Releases do not impact system compatibility unless specifically stated.
Cisco provides the following guidance to help you successfully install and/or upgrade Cisco Unified CallManager software:
· Terminal Services/Remote Desktop Connection is not supported to perform this upgrade. For remote installation use VNC.
· Always log in with Administrator privileges before you begin the SR installation or uninstallation process.
· Exit all other applications and close all Terminal Services sessions before you begin the upgrade process.
· To minimize call-processing interruptions during the upgrade process, register all devices to servers that are running the same version of Cisco Unified CallManager software. Make sure that you register all devices to the backup Cisco Unified CallManager server or to the primary Cisco Unified CallManager server, but not to both the backup and primary servers.
· Upgrade all servers to Cisco Unified CallManager 4.1(3) and make sure that the servers are online before you begin this SR installation; otherwise, pre-upgrade checks may fail or return faulty information. This SR is based on Engineering Special 135. For this Service Release, Cisco supports upgrades from any Cisco Unified CallManager 4.1(3) release up to 4.1(3)ES135.
· If you are using Cisco Security Agent or a supported antivirus agent, you must DISABLE this software and then restart your system before you proceed with this installation. You must manually re-enable these services after the installation is complete.
· Make sure that you disable the following Cisco-verified platform agents and applications; these products may interfere with the Cisco Unified CallManager installation:
o Server management agents
o VOIP monitoring/performance monitoring
o Remote access/remote management agents
· For a list of supported platform agents (i.e. Antivirus Products, etc.), review the following: http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_bulletin0900aecd800f8572.html
· For optimum performance, apply the most current OS upgrade and SR before you install the Cisco Unified CallManager SR. For more information, refer to Cisco IP Telephony Operating System, SQL Server, Security Updates at http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/win_os/os_srv_sec/osbios.htm
· Service Releases contain firmware loads that are current as of posting, however, Cisco recommends that you always download the latest firmware load from the Voice Software Download Center at http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml
· All nodes in the cluster run through a database replication health check during the upgrade process as an extra measure, even though the publisher's database replication check should catch any replication errors clusterwide. If you encounter a warning message on any node during this check, make sure that you stop the installation process and check the log files. Follow the recommendations listed below if the log file displays any of the following messages:
o All agent-implementing jobs are waiting to start
o At least one agent-implementing job is attempting to execute after a previous failure
o At least one agent-implementing job has failed to execute successfully
The following procedure provides details about how to install Cisco Unified CallManager 4.1(3)SR7.
Note: Cisco recommends that you apply this Service Release during a maintenance window.
Note: It is very important to disable platform agents and services, such as NetIQ and Prognosis performance monitoring, antivirus (such as Cisco-verified McAfee services or other Cisco-verified AV products) and intrusion detection software, remote management services, and any other monitoring applications that automatically restart services; this action ensures that your system does not encounter issues that are associated with these services.
· This Service Release upgrades the affected services and files and then it restarts the server when the upgrade has completed successfully.
· Apply this Service Release to all of your Cisco Unified CallManager servers, beginning with the publisher server and TFTP server.
Note: To verify that the installation completed
successfully, follow the instructions in Step 6 below.
Perform the following procedure to install Cisco Unified CallManager 4.1(3)SR7:
1. From the Voice Software Download Center, navigate to Cisco Unified CallManager version 4.1 and locate the
ciscocm.4-1-3-SR7.exe file; then, follow the instructions to download the file.
2. Transfer the file to each CallManager node in the cluster.
3. Double-click the ciscocm.4-1-3-SR7.exe executable file to begin the installation as noted below:
4. Cisco recommends that you upgrade all servers in the cluster sequentially, to the same version of Cisco Unified CallManager software; otherwise call-processing interruptions may occur:
a. Begin with the publisher server
b. Followed by the TFTP server
c. Followed by the sequential upgrade of the backup servers
d. Finally, the sequential upgrade of the primary servers
5. Click Next when the installation process displays a message that asks if you want to install this SR.
The remainder of the installation process continues without any additional user input. The system displays a message when the installation is complete.
6. Verify that the installation completed successfully by taking the following actions:
a. Click Yes when the system prompts you to view the log file.
b. Scroll down to the end of the log file; if errors occurred during the installation, the errors section at the bottom of the log file will be updated with a corresponding severity.
7. If any of the Client Plugins have a lower version than those included in this SR, perform the following:
After you have rebooted the server and completed the upgrade on all servers in the cluster, go to Cisco Unified CallManager Administration on any client machines (i.e. JTAPI, RTMT Client, etc.), navigate to the Application > Install Plugins menu. Choose the applicable plug-in, run the program from its current location, and follow the installation instructions that the system displays.
8. The system may create or edit the following log files during the installation or uninstallation process:
· c:\program files\common files\cisco\logs\CCMPatch\Cisco CallManager 4.1(3)SR7 Installation YYYY-MM-DD HH.mm.log (this file is also accessible by navigating to the Start menu shortcut "Cisco Install Logs" under the CCMPatch folder)
· c:\install\dbinstall\dbinstallXXX.txt
· c:\program files\common files\cisco\logs\CCMPatch\sqlX.txt
· c:\program files\common files\cisco\logs\history.log
Note: This Service Release can take up to 20 minutes to complete the installation.
The following procedure provides details about how to uninstall Cisco Unified CallManager 4.1(3)SR7. (The SR uninstallation process does not change the device defaults to the version that was installed before the SR.)
Note: Uninstall the SR on all servers in the cluster in the same order in which you performed the installation.
Perform the following procedure to uninstall Cisco Unified CallManager 4.1(3)SR7:
1. Navigate to Start > Settings > Control Panel > Add/Remove Programs > Cisco Unified CallManager 4.1(3)SR7 Uninstall.
A dialog box displays to confirm that you want to uninstall this SR.
2. Click Next and then Yes to continue.
3. Verify that the uninstallation process completed successfully by taking the following actions:
a. Click Yes when the system prompts you to view the log file.
b. Scroll down to the end of the log file; if errors occurred during the uninstallation, the errors section at the bottom of the log file will be updated with a corresponding severity.
4. After you have rebooted the server and completed the uninstall on all servers in the cluster, you need to revert to the prior version of the plug-in after the uninstallation is complete, navigate to the Application > Install Plugins menu from Cisco Unified CallManager Administration.
5. Choose the applicable plug-in on the client machine, run the program from its current location, and follow the uninstallation instructions that the system displays.
The system may create or edit the following log files during the installation or uninstallation process:
· c:\program files\common files\cisco\logs\CCMPatch\Cisco CallManager 4.1(3)SR7 Installation YYYY-MM-DD HH.mm.log (this file is also accessible by navigating to the Start menu shortcut "Cisco Install Logs" under the CCMPatch folder)
· c:\install\dbinstall\dbinstallXXX.txt
· c:\program files\common files\cisco\logs\CCMPatch\sqlX.txt
· c:\program files\common files\cisco\logs\history.log
None.
IPMA
Assistant Console plugin to be uploded for 4.1(3)SR6 |
|
New
CDP.sys driver is only copied to C\Program Files\Cisco\Bin" |
|
MGCP
QSIG Interop issue |
|
Adding
8.3(4)SR1 phone firmware to CUCM |
4.1(3) ES135 (Base ES
for 4.1(3) SR7)
4.1(3)ES135 |
|
Phones
handset lamp not flashing if Service param "Hold Type" is true |
|
No
conference model established on CTI port in Offering |
|
Need
support for multiple progress indicators in PROGRESS message |
|
7937
1.1(1) CUCM vob check in defect |
Different
conferences are joined together. |
|
Device
in registered state but not issuing Dial Tone on offhook |
|
Maximum
Counters Per Session i.e. 1000 on WIN CCM(4.1) does not work |
|
Problem
when CUCM sending out an invite with tel uri |
|
Link
'View the User Guide for your phone' not available for 7911/7970 |
|
PLKs
on 8.3 phones have "???" labels when talking to pre-6.0 CCM |
Pickup
failure - Pickup table entry remains as it is not removed |
CCM
release calls on receipt of status message for FAC IE. |
|
CM
doesn't process new call attempt from 79xx with 7914 -79xx seems hung |
|
IPVMSApp
TFTP Client appends extra byte to end of RRQ packet |
|
Communications
Manager RTMT update needed for Venezuela TZ change |
|
DST-
Comm Manager RTMT update needed for 2008 Brazil Summertime change |
|
DST-
Comm Mgr RTMT update needed for 2007-2008 Argentina Summertime chg |
|
DST-
RTMT JVM needs new timezone data to support 2007 NZ DST changes |
|
JTAPI
changes termconn to active/talking for RIU line in progressing st. |
DST
JRE ES/SR update needed for 2007-2008 Argentina Summertime change |
|
Reason
code wrong for Media Device unregistrations (CFB, MTP, MOH, etc) |
|
DST
Comm Manager ToD upd needed for 2008 Australia Summertime change |
|
DST
Comm Mgr ToD update needed for 2007-2008 Argentina Summertime chg |
|
IP
Phone keeps ringing even after CFNA is done |
|
MOH
locks up when using MOH with Full duplex streaming True |
|
DST
Comm Manager update needed for 2008 Australia Summertime change |
|
Thread
leak with IPMA activated but not configured (CTI disabled, users. |
|
Update
7921 CSV and XML files for Release 1.1 FCS |
CUCM
Should Reset Incoming H.245 OLC LCN To 0 When OLC Is Rejected |
|
Locations
Out of Bandwidth causes unexpected Unity Failover |
|
Pickup
group configuration changes to none on shared line |
|
Hear
clicking when headset is attached and display is on |
|
No
audio if source reset RTP timestamp in the middle of a call |
|
GUI
process can lock up when receiving XML messages |
|
phone
unregisters when making toll free and long distance calls |
DST-
JRE update needed for 2008 Brazil Summertime change |
|
ES/SR
can abend during StopServices |
|
JTAPI
problem during conference calls. |
|
DST-
Comm Manager RTMT update needed for 2008 Brazil Summertime change |
|
Communications
Manager RTMT update needed for Venezuela TZ change |
|
DST-
RTMT JVM needs new timezone data to support 2007 NZ DST changes |
|
Backporting
IPMA Assistant Console plugin to 4.x for SR,ES,mainline |
|
CCMUser
login takes 12 Seconds to login. |
|
Browser
back button in Device Association page removes all device associ |
|
Global
Directory errors nonintuitive |
|
receiving
mac address is not unique error message when updating 6608 |
|
CallManager
limits unity 5 voicemail port integration to less than 96 |
|
7911
LCD glimmer / flicker when florescent light is on |
Intermittent
Location CAC Bandwidth Leak |
|
Meet-Me
# Becomes Unusable After Parking It Twice |
|
DST-
Comm Manager ToD update needed for 2008 Brazil Summertime change |
|
CCM
does not mark b-chan as idle after sending release-complete. |
|
busy
hunt group return incorrect release cause |
|
Char
*s_strncpy doesn't check input parameters for NULL pointers |
|
StartMulticastMediaReception
in CCM trace must display multicast IP |
|
Ringing
condition with CCM and BA Dailer version 7.1.3 |
|
Option
for- Stop Extending Call On Q.931 Disconnect Causes |
|
Need
ability to delay media until alerting, progress, connect, or PI |
|
FS-
CCM doesn't send CLC after CTI call hold request |
|
WebKnight
triggered when string 'code=' is encountered |
|
DST-
Comm Manager update needed for 2008 Brazil Summertime change |
|
JTAPI
stopped delivering events |
|
Platform
excetion when adding Terminal Observer |
|
Adding
8.3(3)Sr2 to all CUCM builds . |
|
Ehook-
CCM Feature Description uses "Ehook" term . |
|
Removing
eHook feature from 11/06, 31, 41/61 and 70/71 phone models |
|
Update
Load_ID.prm for 7937 phone |
|
Adding
TNP 8.3(3) and 7937 1.0(1) to CUCM |
|
Adding
8.3(3) features |
CCM
is not porting the OCN in Qsig ICT setup to oCdpnVM |
|
Adding
TNP 8.3(3) and 7937 1.0(1) to CUCM |
|
Adding
8.3(3) features |
Forwarded
inbound QSIG calls sometimes presented as direct call to Unity |
|
Connected
INFO fail to update orig side when PBX Blind Xfer by Reroute |
|
Faststart
used with CTI RP can cause mediaexchange to fail. |
|
Callmanager
needs to pass multiple PI in Alerting message |
|
CCM
crash caused by StationD LineStruct array resize |
|
Calls
from Boulder G729 communicator get fast busy due to MSD issue |
|
Null
pointer exception in JTAPI receive thread |
|
PlatformExceptionImpl
Error randomly occurs for redirect request |
|
External
caller DN was same as agent DN causes JTAPI to create EXT type |
|
7985
Can not disable advertisement of g.722 codec |
6608 |
|
E1
Port on WS-6608 5.4(2) not replying to external ping (ICMP) packets. |
|
ICMP
is disable for 6608 Device |
7921 |
|
Check-in
Cisco 7921 firmware version 1.1(1) to CallManager |
7921
Reboots with race condition between HTTP and SCCP |
|
7921
queues SCCP reset when not in main idle screen |
|
7921
sends SCCP Unregister message unexpectedly |
|
Corporate
Directory blanket search does not display all results |
|
7921
sources RTP from random port rather than port specified in olc |
|
7921G
phone cannot access Corporate Directory |
|
7921
roaming improvements |
|
7921
does not place the softkeys in the specified order |
|
7921
does not dial * or the # before the dial strings |
|
7921
does not dial out on available line if shared line 1 is in use |
|
Ver
1.0(4) incorrectly display softkey Login, Flash, Acct used by CME |
|
7921
phones will register max 2 lines when in srst mode |
|
7921G
error on activating SSID with 20+ chars |
|
Speaker
Phone Activates when Phone Answered |
|
7921
fallback failure from SRST to CUCM . |
|
7921
only roams on max TX retries with APs not supporting QBSS |
|
7921
loses localized tones after reset |
7940/7960 |
|
DNS
Response Parsing Stack Overflow |
7985 |
|
When
registering to TFTP server the Call Manager Config is incorrect |
|
Toggle
Alpha Transparency of Menus using full screen key with 3 states |
|
On
CME, 7985 took ~7 sec to close video chann if CUTA press Hold |
|
Mobility
cell pickup feature is not supported on 7985 |
|
Status
line is not updated when Call Forward All is performed |
|
Unable
to activate callback from 1st line to 2nd line which is shared DN |
|
7985-
Hit redial after call from 2nd line & CB, call goes out of 1st lin |
|
7985-
Phone restarts during active call if nw settings changed & saved. |
|
7985-
Transfer from Line1 to Line2 on 7985 doesnt work. |
|
7985-
ringer stops when callback hit in a scenario. |
|
7985
phone doesnt display meetme number in a meetme conference. |
|
Services
button not working when DNS returns wrong address for CM5.x |
|
7985-
Displays "From Unknown Number" on shared line, when call placed. |
|
7985
- dialled digits are dropped, dialing from Directory in a scenario |
|
7985-
Dialling from directory doesnt initiate newcall in a scenario. |
|
7985-
nw config locked, still erase button accessible in a
scenario. |
|
7985-
gap before first speed dial |
|
7985-
Wrong softkey template is retained |
|
7985-
G729 codec time lag is too long. |
|
7985-No
PC port connectivity when phone is in voice vlan |
|
7985
does not acknowledge reset message |
|
7985
does not failback when secondary CME is not available |
|
7985
does not support video bit rates of less than 64kbps |
|
7985
Can not disable advertisement of g.722 codec |
|
7985-
should be able to handle audio only conference (testing only) |
|
7985-
changes to reflect Cisco Callmanager product name change |
|
Phone
uses old Alt tftp ip instead of existing. |
|
7985-
**#** to unlock needs to key-in very fast. |
|
7985-
Phone reboots on invoking graphicMenuBoundary test. . |
4.1(3)es126 |
|
No counters in traces to indicate available resources for MTP/Xcoder |
|
CallPark Reversion text not displayed when device controlled by CTI |
|
correct DST settings for Newfoundland and London |
|
Button Disapears from IPMA ToolBar |
|
correct DST settings for Newfoundland and London |
|
Extra button templates are displayed for 7937 |
|
Update the QED setting for the 7937 phone guide |
|
User Guide added for new IP Phone 7937 |
|
CiscoAddress.setForwarding reports invalid state 1 (= IN_SERVICE) |
|
MTP port not closed when h323 call finishes before media creates MXs |
|
CTI Route Points stuck in state=WaitforRegister after ccm.exe crashes |
|
H245 Process leak when not getting SDLListenRes from SDL TCP layer |
|
IPVMS crash - race condition or memory shortage |
|
CM strips first digit of PRI DMS Original Called Party Number |
|
CCM service restarts on receiving a valid SIP Packet |
|
Changing User Profile information deletes 'ciscoatuserprofile' in AD |
|
Update English locale Files into the CCM branches for 8.3.3 release |
|
Locale Changes |
|
7940 - 7960 Do not upgrade to P00308000700 |
|
CCM 4.1 No ACK to mid-call INVITE response |
|
Transfer failure when operator transfers caller to ICM route point |
|
CTI Loop causing CM CPU Spike |
|
No CallAttributeInfoEvent after LineEventFilterChange |
|
Call disappears from the CTIOS client on cycling CTIOS server. |
|
Phones stuck at requesting template |
|
CM fails to start if not in CM grp- ERROR readStationRegistrationProfile |
|
IPMA Callback feature causes ccm.exe crash |
|
Transfers-fast go/stop with network delay causes fast busy |
|
JATPI does not provide Network Reached event when IVR transfers |
|
re-tag XML file for guinness QED |
|
CDBLException Dump adding FXO ports into Route group |
|
EM login/logout causes errors in event log |
|
Enter number message keep displaying for a long time after Gpickup |
|
CCM Does Not Populate Correct IP-Port For IRR - Cannot Send IRR Out |
|
reason=unavailable is converted to originalCdpnRedirectReason=0 |
|
An AXL issue when the same parameter is being modified for the multiple |
|
SIP diversion header with reason=unavailable is not handled properly. |
|
Can't add phone template via BAT |
|
Prefix not prepended on the caller info after a call pickup. |
|
Called party number contains number prefix in a scenario |
|
Call is not cleared properly |
|
Add Russian time zones (with DST) for GMT+4 and GMT+5 timezones |
|
SR install reports error "2" when 2nd JRE is installed |
|
CDR
Analysis and Reporting does not reflect DST changes for |
|
Enable Guinness Model phones to appear in CUCM Admin Pages |
|
Call Manager Update needed for New Zealand DST changes in 2007 CSCsc29848call processing failures due to partial table loads |
|
call processing failures due to partial table loads |
|
CCM Shows Conf resources allocated when CFB shows no sessions active |
|
queued MSD from previous transfer causes later MSD failure |
|
ccm 4.1.3 sr5b Outgoing Calls Fail throw DBL exception |
|
CCM-DST
change does not take effect for Timezone Atlantic Time ( |
|
Callmanger TOD Routing Update needed for New Zealand DST changes in 2007 |
|
CDP.sys causing nonpaged pool memory leak identified by Mdl tag |
|
CTI error in event log when logging out of Ext Mob |
|
Inactive or Unassigned DN with CFA still forwards calls |
|
Phone does not display full status message when registration fails |
|
7906/11 display square symbol when the Caller ID too long. |
|
Update Device Support |
|
CM is not forwarding the Notification Ind from QSig Facility Messages |
|
Presentation Indicator is not set correctly in H225 Notify messages |
|
CCM uses internal msec packet size, ignoring size proposed by caller. |
|
Call Manager CTLProvider Heap Overflow Vulnerability |
|
Adding 8.3(1) Display instances to all released CCM branches |
|
If CDR database is offline/suspect InsertCDR service leak memory |
|
IPMA could not read directory users |
|
TSP
crash at ASB bank in |
|
IPMA Assistant Console Install throws warning message after Aug 20 |
|
compatibility issue between IPMA and SMS |
|
Locale file - target-dictionary.utf8.xml needs to be updated |
|
7940/7960 SIP Phone Won't Display CGPN (Caller ID) - 8.5(0) (POS3-08-5) |
|
TopN by Number of Calls - By Extension Reports in CAR are missing users |
|
JTAPI function getType() for calling party returns farEndType = 0 |
|
Unable to clear CFA from IP phone |
|
InsertCDR service should handle character ' |
|
Need a way to control SSH access to phone from CM |
|
Check-in Cisco 7921 firmware version 1.0(3) to CallManager |
|
Special number call is cancelled after 1 ring when keypad is locked |
|
Phone on Antiope vibrates if headset attached when set vibrate alert |
|
User can not do factory reset if setting access is disabled |
|
High multicast can degrade unicast RTP voice quality |
|
75% battery icon appears with full battery |
|
7921 doesn't work with CME unicast paging |
|
Power consumption high after roaming during a call with tspec enabled. |
|
AXL-SOAP fails to update services on CallManager 4.1(3) |
|
Pickup should not fail the action when receiving SsSplitInd with ss2=0 |
|
DA entries get corrupted due to out of order change notification for DN |
|
ccm tftp stops building new config files |
|
SOAP requests return 999 HTTP Response Code |
|
Webknight Firewall in CCM 4.2.3SR2 stops AXL requests |
|
CallManager 4.2(3) ES 31 Web Knight POP up seen |
|
WebKnight blocks 'style=', a valid input from CUOM to CUCM |
|
MTP resource leak if no response are recived to BYE message. |
|
Forwarding should stop CFNA timer and remove the call from PickupTable |
|
Monitor table leak due to Q.SIG APDU in setup then Call immediate split |
|
Pickup fails when call is transferred between interclusters. |
|
Call Fails When PBX Attendant Console performs Blind xfr back to CCM |
|
ST-Cause code 47 Resource Unavailable generated for SCCP to H.323 1CPS |
|
Call over ICT fails when h245 OLCack is sent with wrong LCN number |
|
Faulty Hi-Res CPU timer affects IPVMS driver on DL 380 G4 3.8Ghz CPU |
|
Phone not able to place outbound calls |
|
CCM sends an extra ORC |
|
Change Notification Fails - DBLCNQueue Counts Rise - DBL Ptr Corruption |
|
15 sec delay due to missing MWI retError APDU |
|
Callback fails if IPMA proxy line has PickupGroup or CFNA configured |
|
For signaling only call, CCM should not request bandwidth reservation |
|
After implementing CSCsb42763, can't view or delete hunt pilot. |
|
CM 4.3- Attendant Console Pilot Point returning busy after CM restart |
|
MGCPQsigCdpc process leak for signalling only call |
|
MLA- ASP file is not found in the when accessing VG224 gateway |
|
MTP not invoked for G711Alaw call |
CM-6608 CFB/MTP |
|
KeepAlive interval with CM-6608 CFB/MTP resources |
6608 |
|
6608 T1 resets due to bugtrap |
7905/7912 |
|
CP7912-UK Locale files are downloaded every time the phone reboots |
|
7912 increase number of digits displayed for external phone number mask |
|
DTMF Tx failing 7912G |
|
7912G IP PhoneCannot access corporate directory with French locale |
|
CP7905/7912 phoneDN returned Under DeviceInformationX is Incorrect |
|
7912G does not boot up after firmware upgrade |
|
CP7912G-The behavior after the recovery from the DHCP issue |
|
Incorrect chunk size in http encoding for StreamingStatisticsX |
|
HTTP URL requested by 7912 misses variable name |
|
7912-Calling number is missing from received call history |
|
The memory space of version string is smaller than the macro definition |
|
7912 should retry after HTTP refresh failed |
|
7912 8.0(2) SCCP - phone resets when accessing Corp Dir or other XML |
7914 |
|
Check in 7914 loads |
|
Add new icons for sidecar to support Muster release |
7920 |
|
7920 Firmware 3.0.2 Check-in |
7921 |
|
High multicast can impact battery life |
|
Proxy URL is not supported |
|
Can not reset phone when idle url is active |
|
7921 cannot resume shared line hold calls beyond the first |
|
7921 doesn't show missed calls when keypad is locked and LCD went off |
|
No audio if source reset RTP timestamp in the middle of a call |
|
7921 enters speakerphone mode after call park retrieval with CME |
|
Current volume can get impacted while configuring other volumes |
|
7921 with CME speed dial can corrupt system message display |
|
headset mic audio may distort if in noisy environment |
|
DnD does not work with CME on 7921 |
|
Get a 10 second audio gap after receiving deauth with static WEP128 |
|
Alert tone does not always play when pushed via Play URI |
7935,7936 |
|
Phonebook doesn't display numeric number by default in Web interface |
|
Second phone in a shared line hangs in a failback and failover scenario |
|
Phones hangs while using restore default from UI in this scenario |
|
Phone UI displays error when Restore Factory default in a active call |
|
Fields in "Add New Phone Book entry" in 7936 GUI do not get refreshed |
|
"Server error-413 N/A" appears when wrong input given in phone book |
|
Phone book entries duplicate |
|
No validation for "upload logs" under Diagnostics in phone menu |
|
|
|
No. of characetrs as password input inconsistent in GUI and phone menu |
|
Call Park Reversion message not displayed |
|
|
|
Network settings dont work when 2 phones are in a call |
|
Phone Book does not accept 24 digits as DN |
|
Only 23 digits displayed of a 24 digit DN though lot of space available |
|
Softkey templates working improperly |
|
CFwdAll in an active call breaks the voice path |
|
CP-7936 v3.3.11 can continually reboot after a few weeks on HP switch |
|
7936 may not dial the * character when using Phone Book |
|
Softkeys missing(7936) ,when huntpilot call is answered with callfwdall |
|
Phone plays ringback tone if destination phone has CFA set to unknown. |
|
Deleting the DN freezes the phone |
|
"Http Server" label in place of Http client |
|
DN does not display completely |
|
Reboot does not work |
|
Pressing menu-> phone button in active call phione in a wierd state |
|
c in click should be capital on "Passwords/HTTP Port Change" webpage |
|
Help page does not show hostname |
|
Changing the ringer during an active call puts the phone on hold |
|
Help page of time and date does not list all the date options |
|
Help Page of Network Setup incomplete |
|
Softkey templates incorrect in case of Shared line |
|
7936 phones intermittently fails to upgrade to new load |
|
Icelandic characters not shown on 7936 IP conference phone |
|
Spelling of transfer softkey in case of new call |
|
CFwdAll softkey is absent when initiating a new call during active call |
|
7936 DN display only displays 11 digits of a 12 digit DN |
|
7936 - tone49(zipzip) has beep beep then sounds like long euro ringback |
|
CP7936 Experiencing Possible ARP Cache Corruption |
|
7936- conference soft keys becomes inactive after a few calls |
|
Need support for GetElementManagementFromManagedElementOid |
|
7935 & 7936 stops after 8dhcp discoveries w/no response |
|
DHCP changes can cause phone to reset while on a call |
|
7936 resets or one-way audio due to exceptions caused by DHCP renewal |
7937 |
|
7937-Device Definition Files Need to be Checked In |
7940/7960 |
|
7940 / 7960 reboots when receiving IP fragmented packet |
|
7940/7960 phones fail to upgrade LSC with CME secure authentication |
|
Choppy audio/jitter in incoming RTP to 7960 causes one way audio |
|
no audio after high delay or jitter on network with g.729 |
|
hook switch debounce timer too short on 7940 IP phone |
|
In speakerphone disabled state, 'Dial' softkey active in a scenario |
|
when callwaiting tone is invoked, calls stop getting ringback |
|
7960(sccp) resets under Codenomicon HTTP test suite running |
|
7960/SCCP resets under two cases of Codenomicon TCP Test suites |
|
7960/40 ignores StartTone Messages when in connected state |
|
Phone struck in a loop inside the personal address book |
|
Migrate to use new load authentication key |
|
multiple issue after upgrade to 3.3.5sr2b |
|
Hold call is disconnected when primary CallManager gets back |
7906G,7911,7941,7941GE, |
|
NullPointer Exception on AutoCallAgentImpl.inFocusItemChanged() events |
|
DSP Configuration Files are not Correct |
|
7911 DEV load contains incorrect jar file |
|
Third-Gen SCCP Retries Registration 20K+ Times/Day On Phone-Reg-Rej |
|
R2D- mapPixelCoordinatesToWindow always returns NULL. |
|
Pressing New Call should let user "Enter Number" |
|
M&R- new M&R tone command should override playing tone of same type |
|
Tone not suppose to send to supervisor when selected remote only |
|
Phone does not show complete information for show inventory command |
|
Change the immDiv softkey name to Redirect - Update SIP dictionary files |
|
Need Automation API to get status of headset, mute and speaker lights |
|
Commit of CSCef34402 broke c6slc, other? pikespeak images |
|
make 'DEBUG' trace anticipated for a 1-way audio problem as NOTICE trace |
|
Phone doesn't calculate SRTP auth tag correct for certain RTP payload |
|
DC bias introduced by noise reduction |
|
Play URI doesn't play ring file after first time push |
|
Guinness- Continuous unicast traffic resets the phone |
|
C-P-7941 Changes on the Ring Tone go back to Default after a soft reset |
|
Update memory timings for Goped boot loader |
|
SIP phone failed to clear Held call when CCM restarted |
|
TNP- keyboard I/O errors on reset |
|
No spkrphone dialtone when Trans/Conf button hit on TNP SCCP 8.3.0.9S |
|
ppid found file system issue with unmount beneath stdio file access |
|
Re-partition MIPS memory allocated for ZSP |
|
Call duration timer window on ph display cycles between multiple calls |
|
7971-ringer volume is too high |
|
7971 unable to come up while detecting Supplicant on both switch port |
|
Guinness- Beamish models should not have touchscreen enable/disable |
|
7942/7962- pressing "Cancel" key does not discard change to contrast |
|
797X- Phone DHCP config data got corrupted during firmware upgarde |
|
Phone UI locked up when remaining in fail over mode |
|
minimum send gain not consistent |
|
Static analysis on debug shell |
|
Broadcom phones unable to determine source port of unicast 802.1x EAPOL |
|
Add wideband PLC to codec G.722 and L16K pcm |
|
7975 Gigabit is sensitive to CM signal, and loose many packets |
|
Show
wrong time when using the |
|
Change dsp cost table for iLBC |
|
Noise reduction causes highband rolloff on handset |
|
7931- Overview not in home position at initial bootup |
|
Speed Dials not working on SIP Phones in a specific scenario |
|
DSP resets when Noise Reduction is enabled and spike in audio signal |
|
keypad tones not played on speakerphone when transfering a call |
|
RTCP socket open error may cause audioserver to spin |
|
Fix Static Analysis warnings from TNP security code |
|
GoPed- Auto Line Select does not work as expected |
|
Phone hangs if it stays on placed calls when the peer ends the call |
|
Third gen phone may behave wrong under stress registration test |
|
Guinness- PC port does not forward egress packets |
|
SIP Phone core dumped after failover |
|
Disable Speaker/Handset for TNP SIP doesn't disable Meet me Softkey. |
|
echo on guinness speakerphone |
|
7970 with firmware 8.2.2sr1 speaker not working correctly |
|
Unusable G711 calls (loud noise) |
|
Automation- Need enhancement to AutoStream for SRTP or RTP |
|
Automation does not work on 7911 |
|
need interface getLineButtonPosition() to AutoCallAgentIf |
|
Phone- Dial softkey should not be available for PRIVATE numbers |
|
CallHistory Menu- line key, speaker key, no longer work |
|
Remove tftp command from Mirzam ROMMON |
|
7971/7941 re-append parameters with a redirected authentication |
|
CDP can alter statically assigned VLAN |
|
R2d code doesn't return null reference for corrupted PNG file |
|
TNP SCCP phone displays "???" for DND linekey |
|
Remove I-Hold changes for Enterprise phones |
|
3g-phones -- pick up Sun Java patch to address 2007 DST changes |
|
TNP SIP phone needs to be power reset to re-register in a scenario |
|
slower error propagation causing ph to become leaf of grand child phone |
|
7971 Shows NPE when rebooted during inactive time |
|
7911/7931/7962- DSP process memory leak |
|
Filesystem Privilege Escalation |
|
Volume Control on Group Listen is Broken |
|
When zrun exec VM, it returns immediately& unmount takes causing Ph loop |
|
ppid display notification icon addition |
|
Psylocke code review |
|
SCCP70.MU-1-0-19S advertises iLBC and causes the call drop |
|
7931- Softkeys not Updated in Alerting State |
|
PPID- sunvm should not be trying to come up while /dnld is occupied |
|
Noise Reduction voice metric has erroneous value |
|
Guinness- Update LCD device driver for 7975 (Murphys) model |
|
supposed lock issue on CNU rebooting contention problem with init |
|
SA errors for activate() methods |
|
AutoStream getRemotePort returns neg value for ports in 60000 range |
|
Guinness- Psylocke SOC SA/Cleanup |
|
Inconsistent display of DND Feature (in line button) on SIP & SCCP Phone |
|
KA timer still alive on child phone; phone creating new tranfer process |
|
Audible MWI support |
|
authentication fail on parent, but child authenticates OK |
|
Guinness- keypad device driver for 7945 / 7965 models (Beamish) |
|
SA baselining for TNP |
|
7931-Resume SK does not resume call after scrolling to another line |
|
Merge from DSP Version 4.2 |
|
Phone goes out of memory after upgrade/downgrade due to OutOfMemoryError |
|
Hearing Aid Compatibility tests failed on Guinness/Wideworld TNP |
|
Hebrew chars position too high in softkeys |
|
Comfort Noise needs to be tuned for Wideband codecs |
|
8.3(1) SCCP Phone resets during video setup with non-CM6.0 Endpoint |
|
Display scr. is dark & won't accept input while phone upgarde downgarde |
|
phone as root and leaf for the same file; two roots for the same file |
|
Phone with network plugged into PC port can get stuck if link drops |
|
Osage- Phone drops incoming unicast EAPOL when VVLAN is present |
|
Customer cannot use Codec of their choice after 8.2 phone load install |
|
Parent not sending KA to leaf; leaf reroot; end up with TLOAD |
|
Phones failover to secondary node with wrong cause code |
|
PAE can't exit due to a file lock during shutdown, phone hangs |
|
Cannot answer call by going off-hook |
|
TNP phones on CME can't resume call with Line button |
|
Focus does not shift to off-hook line while another call is incoming |
|
PPID FOUND CORNER CASE- init never reimages in certain instance |
|
Focus should remain on oldest ringing call with mulitple incoming calls |
|
set ringtone after preview ringtone can crash a 3rd gen phone |
|
NAK SMT/ORC |
|
7975 Network Stats page displays the wrong NW port info |
|
Guinness- move interrupt learning code to a helper function |
|
MenuApp Application has wrong icon in title bar |
|
Merge Noise Reduction improvements into Mainline branch |
|
Phone Directory gives incorrect details after upgrade to 8.2.2 |
|
Muster- Phone Errors when pushing URL's with priority |
|
offhook w/ handset for the first time after reboot, no dialtone is heard |
|
7962/42 advertises PAUSE capable via Ethernet AUTO-NEG |
|
PPID Unit Test Findings - TCP Communication Problem on Root Removal |
|
SIP phones run out of memory in Java heap for every call |
|
XML Parse error when phone is dialing |
|
7911/7972- Add tool to dump DSP data structures, initially msg buffers |
|
Remove redundant model specific dictionary entries |
|
Update boot loader on Guinness phones |
|
Replace TI assert function by dspfw define ASSERT |
|
No dialtone with handset off-hook or using the Speaker button |
|
Change text on Power Save Config menu of phone from Display to Backlight |
|
Guinness- Update Touchscreen device driver for 7975 (Murphys) model |
|
Guinness- update LED test app for 7975 model |
|
SBB/SBCB & Barge/cBarge call instance focus incorrect after phone reset |
|
OnHook Dialing from Line2 doesn't work if Line1 and Line2 have same DN |
|
Not able to configure Directed Call park BLF in 7970/71 SIP phones. |
|
GoPed- Add Help for Fixed Feature Keys, NavPad, and LocalFeature PLKs |
|
Graphic Issues |
|
guinness audio improvements |
|
Guinness- use port index to update queue link speed |
|
TNP phones fail to upgrade LSC with CME secure authentication |
|
Enhance kernel memory utilities to report free blocks in the virtual mem |
|
7970/71/41/61- DSPBOOTStart-Sync failure btw ZSP and MIPS-MBOX1=DEAD |
|
Need ability to send hook signal for onhook transfer feature |
|
Phone does not come back up when the PC and sw cables are reversed and r |
|
new threaded PPID algorithm with dual TX threads wont shutdown |
|
"Update" softkey isn't displayed when focus is on LSC |
|
Phones don't handle fatal Java exception properly |
|
IP phone fails to parse the encrypted config file |
|
SIP Tnp Phones display needs to be changed |
|
bug trap 91 on system reboot |
|
Don't write cdp.conf file everytime we recieve packet if not necessary |
|
Changes per UI Evaluation |
|
clean up syslogs in PPID remote and console logging |
|
differentiate illegalStateException in getNodeId() |
|
No help information avail for NAV Left NAV Right button in 797X phones |
|
IDLE Phone with Open detailview screen cause inconsistant DTMF behaviour |
|
CallHistory Menu- Going offhook dials wrong number in special case |
|
With Setting Access to restricted can access Network Config |
|
Phone gets stuck while resetting |
|
SIP 7970 phones showing RemoteHeld state while it has to be in HELD stat |
|
/usr/cache out of space - can't create a new file |
|
7961 phone not show Help info for privacy button |
|
Large increase in PNG graphic processing time |
|
Focus should remain on oldest ringing call with mulitple incoming calls |
|
Handset adaptive gain control needs to match the 7940/7960 |
|
Automation- Need isSelected method in autoobjinfocus |
|
Display Timer on TNP Phones wrong, Meet Me initiated with Trans Pattern. |
|
Shared memory access collision between dspfw and driver |
|
JPN- Cannot Display Kanji via UserToDeviceData |
|
79x1 phone delay to display system message after deactivate DND |
|
Leave space between display of Internal caller ID and Line Text Label |
|
Guinness- create unique queue for reserved mcast |
|
turn on WB handset feature bit in mfgInfo for guinness phones |
|
Background Image list item irregularities |
|
Intercom- 7931 phone cannot complete onhook dialing with incoming interc |
|
Takes long time to receive error from phone |
|
SIP phone stop registering to CCM w/ 50% packets loss |
|
Unknown name displayed if special characters are in display name |
|
dtmf issue in CME software conference |
|
7911 Ph unregister flood console logs with Supplicant logged off message |
|
Top of Softkey Graphics Disappears When Slider Bar is Shown |
|
Add debugging info-- add brodcast TX/RX count to call trace |
|
phones should keep the latest Kfactor value in the phone stats |
|
7914 configured over 15 digit in line number behaves very strange |
|
Guiness 7945s got stuck during ppid upgrade |
|
some SCCP phone types does not play call alert or reminder tone for DND |
|
CallInfo page displays wrong status for the idle lines |
|
convert "Can Not" to "Cannot" in all SCCP english dictionary phrases |
|
SIP7911 stuck during automated upgrade/downgrade |
|
Guinness- Update BN2 to latest diagnostics version 13.2.0.33 |
|
AutoFeatureIf invokeDirect returns success when softkey press failed |
|
Headset LED in wrong state after power cycle |
|
CallHistory Menu- Can't dial with line key|speaker in special cases |
|
Guinness- update to latest diags for all guinness phone models |
|
Privileged Shell Commands available to unprivileged user |
|
Handle REG ALL FAILED differently to allow LSC installation |
|
Root phone not offerring new leaf when its children are gone |
|
7975/45/65- Gig E speed option unavailable Switch port or PC Port settin |
|
Guinness bugtrap- SY MSG- Kernel Shu= 0x6666 |
|
Call Preservation- sccp to sccp intercom call clearing issues |
|
mislist processing removes critical files on upgrade [stale file problem |
|
Need to be able to get the versionStamp for the config |
|
Intercom- phone does not do talkback if onhook dialing is in progress |
|
ESP debug message add (passau) |
|
Guinness- Implement Psylocke programming restrictions |
|
on speaker, noise or mute tone heard when pressing Mute button |
|
Factory Reset require for secure phone to move to another CCM |
|
3rd phones break 802.1x auth when span to pc enabled |
|
Bugtrap 0x91 phones (during fsck) |
|
phone load need to support new timezones |
|
Guinness- provide register access for gig testing |
|
2nd iLBC channel can't be opened as full-duplex to do barge-in |
|
Collapse muster into tnp_main branch |
|
third gen phones power is initally set high power at boot w/line powered |
|
Phone web page http-//Phone IP Add shows ??? character for parameter nam |
|
Update 7975 / 7965 / 7945 bootloader for LED changes in new HW |
|
Pre-dial list shows DN followed by conference after a conference. |
|
flash/buffer comparison failing |
|
Repeated Dialing from Call History Menus causes OutOfMemoryError |
|
CallInfo URL missing VisibleFeatureList tag when application pane open |
|
Secure conference need support for getting icons from confList |
|
7975- Add touch panel calibration defaults |
|
Phone declared as a child twice by same parent due to keep alives TO |
|
SIP Intercom - enable redial feature |
|
Audioble MWI (Stutter Tone) is not sounds correct |
|
Time zone rules do not update correctly on 3rd-gen phones |
|
7911 phone advertise 2 iLBC codec on its capability message |
|
dhcp memory leak |
|
Change dsp cost table for G.722 |
|
7941/61 TNP time displays 1 hour early if power cycle |
|
802.1x packets are not forwarded |
|
Need a smaller font for the call reference for Makaha and Caffreys. |
|
Private RIU calls show up in the callinfo list |
|
IP Phone SSH Vulnerability |
|
Read linenumber from the config file |
|
Noise Reduction total energy parameter rests at 28 instead of 0 |
|
7970 phone in low power mode consumes more power than CDP advertisement |
|
Bogus load name in Phone load element value cause TNP phone to hang |
|
Phone TFTP request packet for a background image is Malformed Packet |
|
guinness- code cleanup in dsp device driver |
|
Guinness- Update diags for Murphys to 13.2.0.23 |
|
TNP Phone SSH Vulnerability |
|
Update diagnostics / BN2 for guinness phones |
|
XML parsing error on LineInfo to turbo phones w/ speed dial configured |
|
MenuApp Application has wrong icon in title bar |
|
7970- Malformed UDP packet DOS attack causes phone to freeze |
|
SIP shows incorrect info for placed intercom call in IntercomHistory log |
|
SIP phone should disable Callback and DND for intercom call |
|
port "reset on sleep mode" ddts to guinness code base |
|
Modify assembly to address Titan Advisory R5691 and c55 Advisory CPU_116 |
|
Multiple softkeys on the phones are "bleached" on touchscreen drag |
|
Need automation API to get tthe time/date from the phone |
|
Update cpk files for Beamish model 7965 phone |
|
Need to Press Right button twice on Nav Pad to close Line Detail |
|
Guinness- nmap TCP connect scan crashes 7945 and 7975 |
|
Composed IPPM messages display + instead of space |
|
Update power requirements for 7945, 7965, and 7975 phones |
|
Guinness- Update BN2 to latest diagnostics version 13.2.0.31 |
|
75 phone call numbers over flows the spaces assigned for it |
|
Recording tone plays abnormally during a call |
|
DSP process dies while running the call features automation script |
|
LCD for Guinness 7975 need color register adjustment |
|
SIP 7911 and 7961- Erase config from Settings menu does not reset phone |
|
Font kerning issue on 7970 |
|
Missing Pixels on the left side of UI displays on Turbo phones |
|
Guinness phones need different EQ based on Handset Hookswitch |
|
Phone does not get registered when daisy-chained with 7961 phone |
|
Customer is experiencing one way audio calls |
|
TNP improvements- /bin/sh should always be a POSIX-compliant shell |
|
7971GE- Sleep Mode issue |
|
7941 - BLF speed-dial status LED does not work |
|
PNG Broken- Phone fails HTTP GET if earlier HTTP request is not finished |
|
wrongly uses tftp server as log server |
|
Rings shouldn't be configured for intercom lines |
|
SIP phone does not answer by lifting handset |
|
LCD for Guinness 7975 phone displaying inaccurate color balance |
|
Phone sends different help ID for intercom line |
|
TNP sempahore traverse |
|
Shared line display & going offhook while in active call distort display |
|
command parse error and command search fail on 7970 |
|
JAL doesn't work as per requirement with c-Barge Conference |
|
Frequency Value for Steady Dial Tone After Stutter is Wrong |
|
PPID Unit Test Findings hash test ugliness |
|
Jphone and init.tab and sleep interaction |
|
Update diagnostics for Guinness phones to version 13.2.0.36 |
|
Phone does not get registered when daisy chained |
|
pressline 2 not working for 2nd line of 7941 |
|
SCCP phone does not register back to publisher after restart. |
|
GUI stuck after changing contrast |
|
SA for img_main (image daemon) |
|
Enhancement- provide an indication of when flash was last formatted. |
|
Guinness- Fix the printing of the Chip Version Register (CVR) values |
|
Ph hits max file download timer of 60 min during firmware upgrade downgr |
|
TNP Phone 7941 second line line button will light up for incoming call. |
|
SIP phone init a new call when pressing the line that already has a call |
|
Hung RS-232 port causes phone upgrade failure |
|
Response.Redirect fails |
|
When ph is going to safe mode or TLOAD its background should be cleared |
|
Ph stuck in IDLE state after Java Error without CallManager menu Entry |
|
7945/65/75 Hardware version 6.0+ uses external gamma |
|
7970- nmap TCP connect scan crashes 7945 and 7975 |
|
7975- PC port goes no link after reconfiguring to 1000F |
|
G722 Monitoring call could not be setup for iLBC primary call |
|
Memory Leak on phones with repeated calls with very short call hold time |
|
Event needed for reset |
|
Change the CiscoError, CiscoStart and CiscoReboot png files for new logo |
|
Phone core dump while running the call features automation script |
|
7971 SIP/SCCP- PC port can be enabled after being disabled from CCM page |
|
7975- Port 0 is not coming up while working with 100 Half Hub port |
|
Erroneous Behavior when DialLine URI on Intercom Line that has call |
|
Gross timeout for downloading file with DLOAD & TLOAD should be changed |
|
when callwaiting tone is invoked, calls stop getting ringback |
|
Host unicast traffic are not forwarded to the egress PC port |
|
GoPed- localization work for Muster |
|
Phone hangs while downloading PNG files |
|
7970- implement ethARLCache functions |
|
TLoad- timer_start fail - doGrossTimeout-serial issue seen on 16s load |
|
831-Settings button access set to restricted disables directories/servic |
|
Callback softkey is presented but it doesn't do anything. |
|
New Default Background Image Required |
|
Jake Featurette check-in |
|
Cloudraker-XML Parser- xml parse error on event ID of Redirect Softkey |
|
Cloudraker-SendDigits URI fails to send in-band dtmf |
|
Wideband Handset available for config on 7931. |
|
7945/65/75 bounce link on soft reset for both PC and network ports |
|
disable audio output during bootup |
|
Alien crosstalk is degraded after CSCsh75383 is fixed |
|
7971 DHCP address from data vlan |
|
New Default Background Image Required |
|
Cloudraker- Missing support of IconIndex in Title element |
|
Turbo/Goped sometimes experienced resets after power recycle |
|
7945/65 becomes inactive after CCM down |
|
7961 crashed when running Codenomicon https suite(Test #9) |
|
call on sharedline lost on phone - both users hit endcall on other line |
|
Update diagnostics in BN2 for 7931 |
|
Ph not register afte XML Parser Excep seen during config file parsing |
|
Cloudraker-phone fails to come up if deleted and tries to Auto-reg SIP |
|
Turbo Bootloader Changes |
|
7962 does not come up with load 8-3-1-10 |
|
7911 phone crash when switching to Arabic locale |
|
Phone Directory gives incorrect details after upgrade to 8.2.2 |
|
TNP Phone Update needed for New Zealand DST changes in 2007 |
|
CIA 1085- lower Voice Mail status line to below DND state. |
|
TNP Phone use Narrowband Vol Table even for WB |
|
CallBubbleSelected.png is one pixel too wide for beamish |
|
Ph in stuck state after capfList config structure change in SEP MAC file |
|
Ph got stuck in Settings screen when Settings is pressed while dialing |
|
7970 RLR is softer |
|
Phone API startMedia request, parameter "receiveVolume" not working. |
|
7975G characters look fuzzy/not formed correctly |
|
Pixels sourounding the active UI tab are not black |
|
Callback Message screen mixed up with Placed call screen |
|
Cloudraker- XML parser- Hardened Soft Key Files schema rules |
|
Resource Image updates for FCS |
|
Update Guinness BN2 for Memory Bist tests |
|
Darker greyscale images cause unreadable display on 7961/41 |
|
Guinness handsfree mic signal can clip |
|
Cloudraker- XML Parser- No Error when tag is duplicated |
|
Update Guinness BN2 files with diags version 13.2.0.60 |
|
Guinness Phones do not respond to 802.1x Re-authentication Requests |
|
Missed call history incorrect for forwarded calls |
|
Underworld - XML Parser Code changes |
|
Underworld- Phone does not shows "bad ring list" for erroneous ring file |
|
Cloudraker- XSI- xml push onFocusGained to phone executes 3 times |
|
SBB/SBCB & Barge/cBarge call instance focus incorrect after phone reset |
|
Update Guinness mfg image to include new diagnostics ver 13.2.0.49 |
|
PS loads fails to switchover to Jap locale |
|
Resource Image updates for FCS |
|
Underworld- Config File schema errors and issues |
|
XML Schema hardening prevent encrypted & non-encrypted config parsing |
|
7970 with firmware 8.2.2sr1 speaker not working correctly |
|
7962- packets egressing PC port should have PC vlan untagged. |
|
New generation phone have lower volume then older phone types |
|
Null pointer exception on XML Parsing for SIP phones |
|
ESW clock not initialized properly by boot loader |
|
7962 barge in no voice |
|
XML data can't be rendered to IPphone |
|
Guinness Handset RLR incorrect |
|
AEC suppression can degrade voice quality scores on Guinness |
|
Guinness- Color models are displaying visual noise on power cycle/reboot |
|
Pixels surrounding the active tab are not black |
|
Cloudraker- CFWDALL and MCID not working on SIP phones |
|
TNP SIP phone can not failover to SRST due to wrong port |
|
Start Media Response does not returns codec string correctly |
|
Guinnes handset - "highs" are little too high |
|
Goped Bootloader Changes |
|
New XML parser unable to display another Ph web page in XML services |
|
TNP phone corrupt background image causes blue image and crash |
|
Turbo- Malformed UDP packet DOS attack causes phone to freeze |
|
Broadcast Storm one way audio for 7961 SIP |
|
Update diagnostics in BN2 for 7911 / 7906 |
|
Guinness- Malformed UDP packet DOS attack causes phone to freeze |
|
Analog codec audio output enabled in early stage |
|
802.1x packets are not forwarded |
|
SBB feature does not work |
|
Update Guinness BN2 mfg image to release signed |
|
Calls transitioning to OFFHOOK state should take focus |
|
send specific XMLobject code into 7970, phone cannt request EM service |
|
Guinness- improve AEC doubletalk performance |
|
TNP SCCP ph unable to come up and register with sidecar 7914 attached |
|
Underworld - XSI Backward Compatibility Changes |
|
SDK version updated to 6.0.2 for 8.3.1.release branch [8.3(2)] |
|
support new Spansion flash part |
|
OS PLL init setting unnecessary |
|
Resource Image updates for FCS |
|
3rd gen phone may loose personalization after rereg to another CCM |
|
Phone will not load from case sensitive TFTP server |
|
Bug in vFillShorts assembly source |
7942/7945/7962/ |
|
Check in Guinness phone firmware to CallManager |
7985 |
|
7985 Screen Powersave LED indicator can't be distinguished from MWI |
|
7985 sources from random port rather than from standard specified in olc |
|
7985 should use symmetrical UDP port numbers |
|
Visual call Pickup notification fails when line audio alert setting off |
|
7985 phone not working with Mobile Connect service. (CMM/SNR) |
|
7985 does not send out video packets w/ IPMA configured |
|
Star50 feature is not working on 7985 video phone |
|
7985 phone with no voice vlan configured fails DHCP/ip address. |
|
7985 enters reboot loop on upgrade when using Alternate TFTP |
|
7985- the ">>" and "delete" softkeys in edit dial screen arent working. |
|
7985- restart loop if load is different between DHCP and alternate TFTP |
|
7985- Phone crashes when long input is entered in inputboundary test. |
|
7985- Ringer stops riniging when try to change ringer drg outgoing call |
|
Ringer stops when 2 incoming calls on 7985 & 1 call ended. |
|
7985- Phone dumps hex value on screen with imageboundary service test. |
|
7985- IPMA - Manager screen goes off after every change |
|
7985- Screensaver leaves chars all over screen |
|
|
4.1(3)es106 (Base for 4.1(3)sr5 & sr5a &
sr5b)
Call has a negative CI number |
|
H225Cdpc Needs To Handle DstopReq In Paused State |
|
Call Control To Address Missing ssRejectionInterceptInd Event |
|
RTMT JVM needs new timezone data to support 2007 DST changes |
|
Phone Service subscribed by Autgenerated Dvice Profile is set to default |
|
Adding THX and Babylon5 features |
|
CCM drops APDU's received in a Progress message while in Transit mode. |
|
Aupair service terminates within function CDBNotifyClient-isRunning. |
|
Aupair unexpected shutdown On 51st NCS Connection Request. |
|
Long delay when calling overlapping DN from Webdialer. |
|
No web access cfg option for 7941/61 in CCM device donfiguration page |
|
Unable to insert 7941 phone with Device Security Mode as Authentication |
|
QRT misreading First and last write in report file |
|
CCM- GW is intermittently lost from route-group route-list |
|
6608 PRI Gateway stayed up even when CCM lost connection |
|
MGCP backual message with length of 12 bytes |
|
Router identify a very short DTMF as a valid DTMF |
|
CTI is sending CtiDeviceCloseNotify during failover/failback scenario |
|
Phantom call stuck in attendant console client servicing broadcast queue |
|
ES/SR Stopservices logging to stopservices.txt instead of ES/SR logfile |
|
OS 2000.4.3a Upgrade Shows 110% On Stopping Services |
|
ES/SR Need to reboot twice after 3.3(5)ES50 Uninstallation |
|
ES/SR Need additional debug for commands run during installation |
|
Merging local dictionary in CCM |
|
CCM unexpectedly shutdown while running ctigw (CUPS) load testing |
|
IPMA-RTMT counters shows wrong value for IPMA services |
|
SCCP analog GW Virtual endpoint registration is rejected by CCM 4.1(3) |
|
called number display on calling phone across ICT shows only DN |
|
add/updateTransPattern-provideOutsideDialTone element is not present |
|
ES/SR - Update uninstallation handling |
|
ES/SR Internal reboot function doesn't work when executed remotely |
|
ES/SR Update Stopservices to stop all COM objects |
7902/7905/7912
Phone response status inconsistent between models |
|
7912 phone should not send StationFeatureStatReq if feature is not confi |
|
7905- Japanese characters are shown as ?s in EM screens |
|
CP-7912 can not use 255 as last octet of SRST address. |
|
IPICS Channel selection by select key does not work intermittently |
|
DnD fails on 7912s |
|
7912 w/alt tftp disabled does not read TFTP server from DHCP |
|
7912 can not resume multiple calls from hold |
|
Connection Monitor Duration changes not applied to 7902 |
|
7912 cannot make new call after lisfting handset |
|
Malformed XML Delieverd from 7912GA when using DeviceInformationX |
|
No response to UserToDeviceData for Key-xxx URI passed from CTI |
|
Init-CallHistory URI does not re-set status line on 7905 |
|
call waiting tone doesn't stop when the second call hangs up. |
|
7912 prefixes fastdial with 'undefined' |
|
7912 affected by ARP storm |
|
7912 authentication problem - password encoding |
|
IP Phone Service problem with 7912 http redirect v8.0 |
|
Able to Change Ring Volume Even when Setting Access set to Disable |
|
7912G-A phone does not obtain address when voice vlan = access vlan |
|
CIA 650- Randomize TimeDateReq's to Call Manager from 7905/7912 |
|
CCM drops APDU with multiple invokes received in Alert message. |
|
H225Notify Connected number IE not handled in some states |
7935/7936
Phone Button does not work |
|
7936 with 4.2SR1 cannot dial digits when in call state 3 (Ring Out) |
|
Scrolling to the end of the line in EditDial causes 7935/7936 Reboot |
|
7936 not passing DTMF while in alerting state. |
|
DTMF tone will not play for consecutive same digits with 7936 |
|
Display is not uniform when dialing an non existing number |
|
Mute dosen't work with |
|
Phone dosen't ring while viewing the MAC address details using **6 |
|
7935 and 7936 do not support 40, 50, and 60ms frame sizes |
|
Phone displays In Use Remotely with out shared line in SRST mode |
|
LED Status changes when the Transfer softkey is selected in SRST mode |
|
7935/36 need to support the priority field in DisplayPriNotify message |
|
Polycom 7936 doesn't refresh after saving the Alt TFTP address |
|
Main/Secondary TFTP Address cannot be modified when DHCP is disabled |
|
Conference not working on 7936 in SRST mode |
|
7936 Phone does n't allow/display full domain name. |
|
7936/7935 does not support JOIN feature of CCM 4.0 |
|
Renumber 7935 firmware load name to match the CCO versioning |
7940/7960
Animated circle (reset icon) seen continuously in a scenario |
|
Add new cons for sidecar to support Muster release |
|
7960 not allow to select 2nd call of a conference call on shared line |
|
A call picked up is not recorded in 'Received calls'. |
|
Upgrade LSC menu strings not flushed on moving out of tht menu. |
|
7960 stops sending CDP packets - causes do1x error disable switch port |
|
Phone remain in Configuring IP state even with proper DHCP response |
|
Option 66 preferred over option 150 based on appearance in DHCP ack. |
|
7960/40 skinny do not detect handset with failover to SRST |
|
Unicode Special Characters blacked out on 7940 and 7960 SCCP phones |
|
Several call progress tones need to be louder |
|
Secure Conferencing Icons for Muster |
|
7960 phone does not calculate srtp authentication tag correctly |
|
Placed call list shows '*' for FAC enabled calls |
|
Secure SCCP Phone Conference Initiator unexpected shutdown on Hangup |
|
7940 ph does not accept new req after rejecting invalid IP address req |
|
7960 SCCP does not play beep tone when DND incoming alert is configured |
|
Phone temporary rejects HTTP connection when its sockets are available |
|
Static, white noise heard w/ 7960 7940 logging into unity with G729 |
|
Update Cisco Logo on phone web pages |
|
Update the copyright year to 2007 on the boot display for the mid-range |
|
7940/60 not streaming sometimes when using encryption |
|
StreamingStatisticsX reports phone as idle when call is active |
|
IP phone at remote offices stuck in opening. |
|
Transfer call leg connects while held leading to call drop, media leak |
|
Resolved the race condition caused by SsManager registration lost due to link issues. |
|
Checking in latest tone file for third generation phones. |
|
Build phone loads |
|
JPN-Cancel softkey not available for configuring 7960+7914 |
|
phone displays Select Ringer... for Invalid DistinctiveRing.xml |
|
UI screen is grayed out when i-button is pressed |
|
Autodial cancelled is shown for a Phone in RingIn state |
|
Phone displays AutoDial Cancel in transfer scenario |
|
7960 tries fallback to CCM that has CCM service shut but port 2000 open |
|
Phone Softkey should be greyed out for Disable Speakerphone and Headset. |
|
7960 produces garbled audio and repeated words for PA Help |
|
Softkeys within various Settings submenu not responding if held |
|
DN not displayed in a hold scenario after line button press. |
|
Init-CallHistory URI does not re-set status line on 7960/7905 |
|
Phone displays Callmanager parameter as UNDEFINED to boot up process |
|
revertPriority = Even fails when Hold Reversion call is oldest |
|
Integrate DSP rev 4.0(2) |
|
parked calls get loud tone when picked up from 7960/40 on CME 4.0 |
|
Callback can not be activated for a busy extension |
|
Abbreviate dialing should not be available if phone not able to call |
|
need to press line button twice to answer an incoming call |
|
Mute light stays on after audio broadcast is complete |
|
ST- 7960 secure phone got TLS error with SRST after CCM 4.2.2 upgrade |
|
one way voice when the timestamp field in the RTP packets rolls back |
|
RTP Tx URI request should be rejected when a call is active |
|
7960 does not differentiate local hold call and remote hold call |
|
40/60 - LA dev size grown above acceptable size limit |
|
7960 with voice vlan resets if IPC is connected to 3rd vendor switch |
|
phone doesn't handle the DHCP next server field and option 66 correctly |
|
7960 displays XML error on hitting directories button with French locale |
|
Phone hangs with HIGH CPU detected- during EM logout & locales installed |
7906/7911/7941/7961/7970/7971
Phone Directory gives incorrect details after upgrade to 8.2.2 |
|
TNP- keyboard I/O errors on reset |
|
7970 phone in low power mode consumes more power than CDP advertisement |
|
Phones failover to secondary node with wrong cause code |
|
Network Locale Version backwards compatibility |
|
Third gen phone may behave wrong under stress registration test |
|
3g-phones -- pick up Sun Java patch to address 2007 DST changes |
|
Hung RS-232 port causes phone upgrade failure |
|
7971/7941 re-append parameters with a redirected authentication |
|
7914 configured over 15 digit in line number behaves very strange |
|
phone UI Locks up when adjust Speaker Volume during registration w/ BLF |
|
third gen phones power is initally set high power at boot w/line powered |
|
3rd gen phones running 8.0(4)SR1 unable to adjust ringer after a call |
|
u7961/41/70 stuck at requesting after phones inbound web access disabled |
|
PNG Broken- Phone fails HTTP GET if earlier HTTP request is not finished |
|
After flash reformat phone gets flash Programming failure errors |
|
Memory Leak on phones with repeated calls with very short call hold time |
|
Pressing New Call should let user Enter Number |
|
Bugtrap 0x91 phones (during fsck) |
|
Composed IPPM messages display + instead of space |
|
Unknown name displayed if special characters are in display name |
|
Exit softkey stops UI when in Security Configuraiton/CTL File submenu |
|
TNP phones on CME can't resume call with Line button |
|
make 'DEBUG' trace anticipated for a 1-way audio problem as NOTICE trace |
|
Customer is experiencing one way audio calls |
|
SenderJoins & Byes values were different regardless of call status |
|
GUI stuck after changing contrast |
|
Osage- Phone drops incoming unicast EAPOL when VVLAN is present |
|
Call duration timer window on ph display cycles between multiple calls |
|
Idle sftkeys displayed on new incoming call after transferw/rel image |
|
AutoObjInFocusIf.getLabel returns incorrect information for a call item |
|
Response.Redirect fails |
|
IP Phone SSH Vulnerability |
|
Internal calls are having one way audio |
|
Filesystem Denial of Service |
|
Phone doesn't calculate SRTP auth tag correct for certain RTP payload |
|
Stutter Tone quality problem when using speaker / line button |
|
Focus should remain on oldest ringing call with mulitple incoming calls |
|
Phone displays CM down in a active call during failback |
|
7961 phone not show Help info for privacy button |
|
No dial tone is heard after togglling the hookswitch in ring out state |
|
Focus should remain on oldest ringing call with mulitple incoming calls |
|
CallHistory Menu- line key, speaker key, no longer work |
|
SIP Phone goes for a reset when proxy address name starts with _ |
|
phone resets after warning out-of-chunks for memory tracking |
|
Caller-id is not updated correctly for conference calls |
|
Retrieving a parked conference call, disconnects the call |
|
Phone unexpectedly shutdown running Codenomicon SIP test 4913 |
|
unable to do cfwdall if kpml is enabled in sip-srst mode |
|
SIP phone failed to clear Held call when CCM restarted |
|
call tranfer after cfw noan on tnp sip phone failed |
|
Incorrect Date header value in SIP REGISTER request |
|
SIP Phone needs to also detect non-localized Conference |
|
Number stored in missed calls not updated upon receipt of SIP UPDATE |
|
Not able to Set CallFwdAll on tnp sip phone in particular scenario |
|
TNP SIP sometimes sending malformed to or from header |
|
7970 sip sends invalid presence subscription causing high CPU |
|
Failed on multipl forward from SIP phone to SCCP phones |
|
tnpsip phone doesn't light up blflamp when destination press callfwdall |
|
Phone unexpectedly shutdown when messages hard button is hit. |
|
Call not forwarded after CTINewCallAcceptTimeOut on SIP TNP phone |
|
Transcoder is not able to handle correctly locations |
|
Active Server Pages exception first time CCMUser page is loaded. |
|
7936 Phone Displays Host not found when accessing corporate directory |
|
Need ability to tag dashes on 12 digits calling party number |
|
H225 / SETUP RedirectIE not populated when VMprofile is created w AXL |
|
Callmanager Disconnects BRI call with Call State Mismatch |
|
Added Prefix on calling num. for inbound calls removed from CDR records |
|
CDR Analysis and Reporting does not reflect new DST changes |
|
Time Schedules Limitation |
|
Calls not transferred to always route member after hold timer expiry |
|
WD logs ERROR-WDNotStarted - Failed to startup WebDialer application |
|
CCM-DST change does not take effect for Timezone Atlantic
Time ( |
|
DirectoryConnectionFailed alerts when DNS server unreachable |
|
SIP does not return error when failed to open UDP port for SIP trunk |
7921
Check-in Cisco 7921 firmware version 1.0(2) to CallManager |
|
Unknown DRQs CM to GK |
|
Call Redirect and CcSetupConf at same time in CM Call Processing |
|
TransferManager splits pair of SsInfoInds to 2 dif. Transferring process |
|
Double TransferStart/TransferEnd caused by SsRedirectCallInd |
|
Detailed RoutePlanServer Trace Results in CallManager Restart |
|
Redial Onhook fails when Routelist contains QSIG+NON-QSIG Route Groups |
|
Callmanager TOD routing not updated with DST patches |
|
Need to change PTT URL to Application URL |
|
CTI is not setting more flag correctly when more than 50 Park DNs |
|
Fail recieving SIP message when there are a lot of SIP Trunk |
|
Cisco VoiceMail Port Wizard freezes when attempting to add port DN's |
|
Install of 4.1(3)esA0 fails |
|
Forwarding Table incomplete after CCM loses connection to Publisher SQL |
|
SIP Trunk sends 200 instead of 488 on reinvite with no voice caps |
|
TSP - Update Unmodified Calling DN with Modified when call is Offnet |
|
Attendant Console returns error if dial busy station |
|
Need to have 4 new Service Parameters to control the cgpn prefix. |
|
Device/Line goes OOS when CCM receives LinkOOS from other node |
|
H.323-NonDialable Redirected Number Causes Corrupted CDR |
|
Need Connected Number IE support in H225 CONNECT message. |
|
MGCP-Non-Dialable Redirected Number Causes Corrupted CDR. |
|
Phone hangs/freezes in a blind transferred scenario |
|
Unable to update a time schedule which has over 22 time periods |
|
When conferencing, "Invalid Conference participant" is shown on phone |
|
Merging local dictionary in CCM |
|
TAPI does not always indicate correct CFA status on phones |
|
Check-in 7921 firmware to CallManager |
|
Cannot manually update / change phone load in DEVICE DEFAULTs page |
|
race condition leads to MTP leak |
|
CM Cdcc / bandwidth leak - HuntList stuck in paused state |
|
CCM fails to send DLCX when receives QSIG ReleaseComp before CRCX Ack |
|
right click transfer in attendant console fails, receiver gets MOH |
|
Create Voice Mail is not working When MLA is Enabled For FAUser. |
|
MLA- ASP file is not found in the when accessing VG224 gateway |
|
Unable to create new or modify VG224 ports. |
|
Need update to "devicelistx.asp" to support new Cisco 7921 wireless phone |
|
Redirect call across 3 ICT disconnected when multiple hold/resume |
|
MGCP/Qsig User name not displaying , Alerting name with ACSE |
|
H245Interface does not use received h245ta to start H245 Client Session |
|
AXL getUser fails after AD plugin integration |
|
ST-TFTP service does not build device config files after upgrade |
|
The phone config files are missing in TFTP2 server |
|
Callmanagers do not have all timezones included in Date/Time Group |
|
Update 7921 CSV and XML files for FCS |
7920
7920 3.0.1 FIrmware and XML Schema Check In |
|
Full Access & Read Only Access users are denied to view some pages |
|
MLA generates error when configuring CSS for DN |
|
Error Message ASP file is not found in the mapping for ROUser |
|
Full Access user Not able to Run IPMA Wizards. |
|
FullAccess User Can't edit HL/P, RL/P, DP from Route Plan report. |
|
Multiple change notifications received for Route filter clause update |
|
getHuntList response with wrong name space |
|
AXL removePhone API doesn't remove the autogenerated device profile |
|
HuntList needs to be fixed |
|
MediaManager is not releasing the pre-allocated MTP resource |
|
H323 FastStartCCM Closes wrong forwardLogicalChannelNumber in CLC |
|
CCM does not allow IPVC PSTN call to be setup with G722 |
|
Race ConditionStationOffHook at same time as CcSetupReq received |
|
Perfmon of >1 CM Shows 6624 GW Port-1 Registered Simultaneously |
|
No voice after Call forward in a scenario-Call Diversion by reroute |
|
Clean up the huntlist trace for better trouble shooting |
|
hunt list incorrectly extends call to next line group on race condition |
|
CCM does not start media in some scnario involving IPVC GW and Tandberg |
|
media resource status is out of sync between MatrixControl/Call Control |
|
Redial not working in a scenario involving overlap sending |
|
Allow VideoCFB to update itself's capabilities |
|
No transfer start event sent when CTI app redirects call during a trans |
|
H.323 phone calling 7960 legacy SIP over H.323 ICT fast start fails |
|
Incorrect Missed Call Information when Call is routed via HL/LG |
|
|
|
CallManager 4.2(1)sr1a -redirect and transfer occuring at the same time |
|
Locations Out of Bandwidth causes unexpected Unity Failover |
|
TFTP unexpected shutdown When Length Of File Name Exceeds 256 Characters |
|
TFTP stop rebuild cache for some specific events |
|
When CCM 4.2 is Secure, HTTP will not serve Un-Signed files, like TFTP |
|
callInfoDisplay -Case Sensitivity different in getPhone and updatePhone |
|
Failure adding member to CiscoAdminRepToolAdminGroupUsers Group. |
|
RTMT (RISDC) not showing true value of CTI items when threshold reached |
|
Cannot login into Tomcat Web Application Manager |
|
User field "Department" - Extending beyond 30 characters to 40 or more |
|
CallManager input validation needs improvement. |
|
ScalabilityImprove WebDialer call rate on 7845 to 4 calls/sec |
|
Unable to insert 7941 phone with Device Security Mode as Authentication |
|
CCM4.1(3)ES. SQL error when inserting a 7961 phone |
|
Add support for Security feature in Communicator |
|
3.0.1 English Dictionary Check In |
7935/36
7935/36 reboot using corporate directory search on 3'rd party LDAP server |
|
7936 with CCM 5.0 displays Server Not Found when access Corporate Dir |
|
7936- Can gain access to web interface w/o admin password |
|
7936 does not register G.729a capability along with G.729 capability |
|
Selecting Tone Test and exiting hangs phone |
|
Setting up Admin VLAN id brings up the phone without a DN |
|
7936/35- Ignore CDP V1 message for VLAN configuration purposes |
|
7936 phone hangs when pressing hold & resume |
|
7935 does not recover after power/network loss |
|
7936 phone shouldn't release its VLAN until the TTL(CDP message) expired |
|
UI displays Failed to set VLAN Idwhen changing n/w setup in activecall |
|
When we dial the DN through web page ,message flashes for sec & proceeds |
|
7935 does not register G.729a capability along with G.729 capability |
|
Change Notification fails to update Digit Analysis. CallForward fails |
|
MGCP PRI should prevent repetitive datalink up and down |
|
IdleCI not passed via NotifyReq when transfer fails |
|
IdleCI not passed via NotifyReq when transfer fails |
|
Provide a user identity for call |
|
TAPI Reports 7941 & 7961 Phones as Unknown Device Types |
|
TSP unexpectedly shutdown on application server |
|
missing 7906 default load 8.2(1) |
7985
Packets received on PC port are not forwarded in some configurations |
|
7985 does not display animated icon w/ RTPRx |
|
Restart reason sometimes is not correct under Network status |
|
Phone can rarely stop making calls after CCM failover/failback |
|
Confrence List Remove feature does not work on CCM 5.0 |
|
Invalid dialed number when dialed from directory displays no information |
|
Callback Notification window does not close after Dial is pressed |
|
Phone sometimes does not fallback to the correct Standby CCM |
|
Wrong display of softkey sets and callinfo on IPMA assistant phone |
|
IPMA manager should not exit from IPMA service w/ 1 assistant |
|
Phone did not register with the Call Manager after a network power loss |
|
Phone unexpectedly reset during a long duration H.263 call |
|
Some softkeys not work correctly with CiscoIPPhoneInput object |
|
7985 phone not working with Mobile Connect service. (CMM/SNR) |
|
7985 un-registers from the Call Manager after the switch speed changed |
|
Network status should contain last restart reason |
|
Hoot & Holler service does not display Handset icon with RTP/Rx RTP/Tx |
|
Visual call Pickup notification fails when line audio alert setting off |
|
7985- Ignore CDP V1 message for VLAN configuration purposes |
|
Equation type input can have unexpected delay when pressing numbers |
|
Pressing a number in Ring Tone menu works differently than other phones |
|
There is no Call Status information available via the web pages |
|
7985 appends devicename in HTTP request when searching directory users |
|
Changing volume during the Hoot & Holler service cause audio to be sent |
|
Hoot & Holler icon was not removed after exiting the service |
|
Background image after download is obscured by the image menu |
|
7985 can not handle URL with 255 char. |
|
PC Voice VLAN disabled does not work with Admin VLAN |
|
IPPA phone service shows some unexpected error messages when logging in |
|
Call accross ICTs may fail when hold or transfer |
|
Call accross ICT trunks may fail when hold or transfer |
|
CTI Ports/Route Points do not go in service after reset |
|
Overlap Sending broken when using redial function while phone is onhook |
|
Incorrect DNIS in the CDR when using speedial and Route Pattern Overlap |
|
Error on Service Parameter on CCMAdmin |
|
CallManager should handle T1-CAS incoming call after GW channel OOS |
|
CallManager MGCP T1 CAS Channels Must Recover from Out of Service (OOS). |
|
OpenSSL DoS vulnerabilites- CVE-2006-2937 & CVE-2006-2940 |
|
ccm.exe unexpectedly shutdown with c0000005(access violation) due to SIPHandler thread |
|
Locations Out of Bandwidth causes unexpected Unity Failover |
|
Aupair unexpected shutdown On 51st NCS Connection Request |
|
CCM reporting encodingStyle as ISO-8859-1 instead of an http URL |
|
Update needed for N America DST changes in 2007 |
7911/7941/7961/7970/7971
Beep tone max power is only -22dBmO |
|
FSCK stuck in deadlock with syslogd |
|
Enumeration Pattern Code Updates |
|
Phone sends corrupted RFC2833 packets when SRTP enabled for call |
|
Dev Studio changes to make building Communicator easier |
|
Secure phone does not retrieve the SEP file |
|
7931- Call Plane Detail View is not open after On-Hook dialing |
|
CiscoIPPhoneStatusFile LocationX parm not used for small image size |
|
Commit of CSCef34402 broke c6slc, other? pikespeak images |
|
Titan dsp host could 32-bit read between dsp firmware two 16-bit writes |
|
Osage- Max Input Rxd msg displayed when 32 chars input to Shared Secret |
|
Power Save Configuration options missing in Settings |
|
Osage- Status Messages for 802.1X Authenticatio not as per Osage UI spec |
|
softkeys disappear after blind directory transfer |
|
TNP- keyboard I/O errors on reset |
|
RTCP- Exiting Hoot & Holler cause phone to send bogus BYE packet |
|
7931- Exception in OverviewModel during restart |
|
Support G.722 56k and 48k in the Audio Server |
|
TNP phone logs "Unable to get memory" message on console |
|
pressing volume key then speaker button can lock up phone |
|
G.722 K-Factor Table incorrect |
|
Highlighted Call isn't displayed if 10th call ended leaving 9 held calls |
|
7970/7961- dtmf burst is played with a double duration |
|
Phone does not send un-register message to SRST on fallback to CCM |
|
7931- Pressing Line button does not change Line focus |
|
Onhook dialing produces delay in feedback sound with last digit |
|
IP phone fails to do HTTP authentication |
|
7931- Overview not in home position at initial bootup |
|
RTCP socket open error may cause audioserver to spin |
|
under is only 20 chars instead of 64 |
|
Dynamic Trace level registration results in file create/delete operation |
|
EAP-Request/MD5 to PC supplicant could not pass thru Gig phone |
|
Static Analysis Codebase Cleaning on Select Files |
|
7961 phones not processing CTI request to disable softkey |
|
TNP- dhcpRcv.c - uninitialized variable |
|
7970- Phone lock up when message URL has max or 255 character |
|
IP Phone should re-DHCP immediately after DHCP NAK |
|
7931- scroll up and down, sometimes a leftover icon appear next to label |
|
show inventory command returns no data |
|
RTCP- SDES packets are not being padded correctly |
|
Idle Prompt for SRST cannot be set back to the default value |
|
Phone not sending DHCP traffic to pc port |
|
Unable to dial from external dir list after cancel edit dial |
|
LCD display does not always show status of 3 consecutive lines |
|
7911G experiences loss of registration |
|
SIP phone show "Connected" in call preservation if user in/out line disp |
|
7961 with voice vlan resets if IPC is connected to 3rd vendor switch |
|
Static Analysis Codebase Cleaning on Select Files |
|
Ringing phone ICON keep showing up on the phone display without call |
|
Skittles- Retain Dialplan from CCM while failing over to SRST |
|
IP phone not direct HTTP request to proxy server w/ unresolved DNS name |
|
Phone does not have "End Option" field with DHCP Release message |
|
RTP Tx URI request should be rejected when a call is active |
|
goped won't autoscroll to previous line/call in multiline scenarios |
|
3rd gen phones running 8.0(4)SR1 unable to adjust ringer after a call |
|
When uri is not responded by user, second uri post just hangs forever |
|
Clean up debug options available / messages |
|
Line DN label appear to be shifted a pixel or two to the left on Display |
|
Digit tone improperly continues until call connect |
|
JPN hone freeze at Cisco Logo after reset due to Java OutOfMemory error. |
|
7961/70 fail to transfer a call with line 2 from Directory |
|
TNP- Remove NULL term from hostname in DHCP request |
|
7971 displays "Ethernet Disconnected" briefly |
|
Phone core dump when terminating mulitple calls |
|
phone not fallback to CCM and shows "Restarting...". |
|
Enumeration Pattern Code Update |
|
Mute Button is enabled when Phone Speaker Button throws Error pass Limit |
|
On turbo the overview is distorted when a new call is created and ended. |
|
Osage- Transaction Status does not update unless menu is re-entered |
|
TNP SIP phone uses wrong default TLS port number |
|
Handsfree Receive Frequency Response does not meet the mask |
|
debugsh- set LOG_DEBUG trace level for sunvm.cnuw/ debug SIP/JVM command |
|
Phone does not detect Invalid Load Server IP address for "A.B.C D" |
|
Phone Ringsin Continuously,Need to power off/on to clear the call |
|
7911 SLR is 5 dB softer than required, its ok in GL mode |
|
IPPM- Phone displays XML Parse Error when accessing Contact List |
|
7961 - PC cannot see data traffic if PC Voice VLAN Access is disabled |
|
TNP SIP phone can not handle long Unicode callid/linetext |
|
7931- Clean up OverviewModel ACTIVATE_REQUEST event handler |
|
7970 Runs out of memory as phone when idle URL is used |
|
7931- Phone looses softkeys when exit from IDLE URL screen |
|
Incorrect values in RX/TX_START_TIME and/or REPORT_TIME pegs |
|
Soft factory reset does not clean files from /etc/sfr.tab |
|
RTCP- With RTCP disabled web StreamingStats Report Times are invalid |
|
Include Kernel.core into the sylog files for debug purpose |
|
Not able to use Dial Sofkey in Corporate Directory |
|
TCP not sending all posted data after socket close |
|
7911/41/61/70/71 - 2 concurrent XML posts result in Error 0 or Error 6 |
|
devoplement build (TNP) script does not work |
|
Dial Softkey should be disabled for corporate directory/PAB/FastDials |
|
Turbo- DoS tool icmpsic crahses phone on Bugtrap 0x93 |
|
Unmount Error |
|
HTTP sessions are not currently aged-out |
|
CreateStringMatchProperty does not update the allowedValues |
|
TNP - 7911 phone needs an 802.1X port lookup mechanism |
|
9 lines with call in Hold Reversion, phone stops ringing |
|
provide for next generation static analysis for TNP |
|
RTCP- BYE packet has padding bit mistakenly set |
|
7941/7961/7970/7971 Aliasing in high band when using wideband headset |
|
7931- LineFullDisplay detail is missing from the title |
|
Call History Enhancements for Chumbawamba Phase 1 |
|
7970- reduce msg sizes being used in network daemon IPC |
|
Static Analysis Codebase Cleaning on Select Files |
|
When calls are selected/unselected, sorting is done immediately |
|
TNP - 7971G-GE forwards 802.1X packets twice |
|
Exit softkey stops UI when in Security Configuraiton/CTL File submenu |
|
7931- May have a Java Memory leak in disposeDynamicFeature |
|
Static Analysis Codebase Cleaning on Select Files |
|
IP phone stuck at Cisco Logo screen when reset from CCM w/ sidecar |
|
Can not login to phone during automation testing |
|
support persistent status line display on SIP phone in SRST mode |
|
Phone throws exception upon going off-hook |
|
Dial URI w/ Active Call doesn't Invoke Call Options when no app in focus |
|
Static Analysis Codebase Cleaning on Select Files |
|
7931 Titles in Line FullDisplay aren't left aligned at at the same place |
|
Phone continues to ring after shared line picks up a transfered call |
|
mipspacker not use CNU versioning for BN2 image |
|
7931- Line number overlayed with ellipses ... while in active call |
|
7970 SCCP requires Authorization when hitting **# to unlock the phone |
|
Static Analysis Codebase Cleaning on Select Files |
|
Phone Service unavailability message corrupted |
|
UDI Time Zone not displaying string from phone config file |
|
7931- Handsfree RLR does not meet the spec |
|
Phone not showing "Duplicate IP Adress" in status line |
|
HOST Field Send IP Address Instead of Defined Hostname |
|
7911 Phone speed and duplex settings not saved |
|
CP-7971 does not cache TFTP address if option 66 set TFTP server name. |
|
TNP phone sends StationSubscriptionStatReqMessage at restart |
|
Focus changes to the new ringing call before 10 secs.. |
|
Reset on sleep mode phone would not put it back to sleep mode |
|
CiscoIPPhoneDirectory/DirectoryEntry/Name should be restricted to 32 cha |
|
TNP- check return value when writing dhcp.conf |
|
Remote in use calls with no caller ID should display "To Unknown Number" |
|
Sanity- Core produced for rtsp on restriciting incoming bandwidth/bitrat |
|
Fragile file cleanup and performance enhancements (Jasmine featurette) |
|
7931- Tuk Tuk noise heard while using wideband codec for a call |
|
7970 Phones have incorrect active display during shared line call |
|
SIP phone should reattempt download of softkey&dp on TFTP down/ timeout |
|
For Cbarge "CM down,features disabled" message not displaying on 7970 |
|
7931- Headset icon not displayed when Headset LED is pressed |
|
Expand Directory object name field to accept 64 characters |
|
7931- Softkeys disappear with 4 sofkey templates |
|
7971 should set Audio Preference to default values after Erase |
|
Muffled voice on receive for some calls |
|
cnu recover second look |
|
7911- GroupPickUp does not work |
|
Unknown name displayed if special characters are in display name |
|
7970-DHCP- Rejects DHCP request with option 15 from CNR |
|
Display on shared-lines not-in-call is not consistent in cBarge scenario |
|
7931- Incorrect call appearance on shared trunk monitor calls. |
|
Call Focus shifts to Held call for consultative conference call leg |
|
TNP - Soft factory reset should clear 802.1X PAE info |
|
7931- Enable video support |
|
Focus is on wrong call when line view is opened indirectly |
|
Change the 7906 BN2 to use RELEASE keys for pilot build |
|
Turbo should not advertise G.722 |
|
Dynamic features like BLF Speed dial and Privacy are not working |
|
Call fails when no dialplan and registered to SRST |
|
Conference on Alerting with 8-0-2-4S load |
|
Update 7911 diagnostics to version 10.02.00.06 |
|
CNU kernel BugTrap 0x91 with V-E-R-Y specific conditions |
|
TNP phone stuck in blank screen during upgrade to 8.0(3) load |
|
third-gen phone 8.2(1) recover process is not displayed |
|
dsp ingress frame timestamp not following RTP RFC3550 |
|
sleep() system call not POSIX compliant |
|
AbbrDial key shouldnot be active when speakerbutton is disabled |
|
Text Item Displays are not right justified in RTL locales |
|
Phone should explicitly turn on display when reset/lost registration |
|
SIP phones should Ignore unknown softkey set names in softkey xml |
|
7931- Add icons to the DetailsFullDisplay |
|
CIA-680 Support on 3rd gen phones |
|
revertPriority setting not used for 1st call after changing the setting |
|
Third-Gen phones running 8.0(3) do not hear multicast audio from RTPMRx |
|
8.2 phone load causes robotic issue at customer site |
|
Dialplan is not supported when Failover to SRST |
|
Highband noise reduction tuning |
|
Bugtrap 0x91 phones (during fsck) |
|
unable to disable kpml on TNP phone registered to CME |
|
TNP- send DISCOVERs if no DHCP server can be found |
|
IP phone reset with DOS attack |
|
7941/61 LCD controller must be reset at startup time. |
|
Arabic locale missed QRT on dest info |
|
Empty Dial list is getting displayed on phone |
|
Static Analysis Codebase Cleaning on Select Files |
|
Default router entry removed when dup ip present |
|
Can not press line 36 on 7970 with 2 sidecars |
|
7931- Unable to answer call on 2nd line using phone handset |
|
"On " prompt doesn't always work |
|
Static Analysis Codebase Cleaning on Select Files |
|
TNP- "show inventory" CLI output not adhering to the specificication |
|
redial sk is not active in onhook state |
|
getEndPointInfo reports MWI setting incorrectly |
|
vm -mem broken on Broadcomm platform (7941/61, 7970/71) 8-2-0-20 |
|
LCD display shows status of Lines 22-24 after phone boots up not 1-3 |
|
Turbo- DHCP recv socket error on bad address |
|
7961GE stops receiving EAP-Req/ID during long duration reset test |
|
Static Analysis Codebase Cleaning on Select Files |
|
7931- Doesn't show IDLE display on phone display after restart from CME |
|
TNP phone fails to display the switch info at its webpage |
|
7970-PNG image file download unexpectedly shutdown the phone |
|
SYN ACK messages from phone not DSCP tagged |
|
Jphone- Navigate problem under network statistics menu when debug mode |
|
make property retrieval from RMS store file effecient |
|
Handsfree SLR does not meet the spec |
|
Static Analysis Codebase Cleaning on Select Files |
|
Add volume control for local and network tone |
|
7931- Speed dial does not display called-id when another line offhook |
|
Selective graying out of AudioPref menu items incorrect on inline power |
|
Placed calls are not multi-party and should not show a MP call history |
|
Phone Continuously displays "Requesting...". |
|
Softkey wrong after fallback from SRST |
|
7961 (and 7941,7970,7971) doesn't display Call park number after getting |
|
Static Analysis Codebase Cleaning on Select Files |
|
Static Analysis Codebase Cleaning on Select Files |
|
7931-UI shows lines 22-24 when line button pressed with AppMenu Open |
|
Settings -> Device Configuration -> UI Configuration menu is missing |
|
Call History Lists inaccessible after having max entries and deleting 1 |
|
7931- Phone restart from CM duration test leads to Disk full |
|
Add SIP related changes to support G722 for ph0 of wide world |
|
Missing Pixels on the left side of UI displays on Turbo phones |
|
phones should not advertise Voice VLAN on PC port |
|
JTest- SIPCCAdapter.java switch statement missing breaks |
|
7931- Factory Reset Walk LED pattern is only 16 |
|
7971 phone reverts to old config after changes saved to netwk config |
|
7931- LEDs for lines above 8 do not illuminate |
|
debugsh should support RTCP trace |
|
Cfwdall fails to come back on CCM after fallback from SRST |
|
7914 displays old version of remote-in-use icon |
|
Line LED not lighting up or delayed on incoming calls |
|
Phone display not turned on when going into reverting state |
|
TNP SIP Phone resets after auto register due to default load info missin |
|
PNG Broken- Phone fails HTTP GET if earlier HTTP request is not finished |
|
Pushing RTPRx or RTPMRx URI to phone in a call enables mute |
|
Call Statistics menu- Sender size is not a correct format |
|
SIP phone UI Locks up and Keypresses ignored (still registered w/ CCM) |
|
UI locks up & phone cannot register |
|
Timer Exception seen in TimeDateRequest |
|
Clear softkey does not work in Status messages screen |
|
Outgoing ringing and incoming ringing tones played at same time |
|
apply patch for Diab compiler from WindRiver |
|
Add new tone messages to make traditional/stutter tones selectable |
|
Phone accepting duplicate IP |
|
Static Analysis Codebase Cleaning on Select Files |
|
7911, 7906,7931 & 7921 have poor voice quality with G711alaw codec |
|
Out of Memory - Connection refused errors after duration testing |
|
Turbo- 1st incoming call can't be answer if 2nd one be connected first |
|
RTCP- RR/SR packet is missing some info when there is 2 report blocks |
|
SIP gives different Error message than SCCP in Locations scenario |
|
7931- IDLE URL Refresh timer doesn't work in 66DEV image |
|
Shared line display & going offhook while in active call distort display |
|
Write to the TNETV105x PCNTRL "Access Control Reg" must be 16 bit |
|
TNP- libcso.map from build should be saved |
|
New Features - Auto Call Select and More Key Timer |
|
7931- Leave 1 pixel space w.r.t. App Menu/Headset/etc |
|
Line reports as unregistered, but it's not, after failover |
|
Re-sync tone table if dsp host re-starts |
|
Phone core dump while running the call features automation script |
|
Phone not retrying the re-IP after dup IP |
|
7961/41 Speaker LED on even after pushing End key |
|
SETTINGS softkey does not work if no DHCP server available during bootup |
|
mount command exiting with status code 64 |
|
KATE Input causes NPE and non-password data while using XML services |
|
u7961/41/70 stuck at requesting after phones inbound web access disabled |
|
SCCP phone does not register back to publisher after restart. |
|
Need an API to assign a local port to TLS connect |
|
LineModel dispose call throwing a ClassCastException |
|
Static Analysis Codebase Cleaning on Select Files |
|
Dialer does not close correctly after Cancel or Idle Timer Expires |
|
Need filter coeficients for headset, handset and speakerphone |
|
Static Analysis Codebase Cleaning on Select Files |
|
Multi-Party Call History - Transfer case - Received call "from" details |
|
Audio Server K-Factor table for G.722 |
|
CNU Flash Filesystem not recoverable if it fills up |
|
certcnu.bin failure- GETCNU- CNU image update failure; code = 10 |
|
Status of BLF SpeedDial does not get updated. |
|
need feature parity between sip and sccp phone for speed-dial |
|
Endcall softkey doesn't work in Call Preservation |
|
Answer and DnD Softkeys are not always displayed when a call is rcvd |
|
softkey disappears on the phone after several calls are made |
|
7970 precedence call waiting tone does not stop |
|
Issue with Pegs when the call is remotely held and on MOH |
|
wrong filepath used after posting a TFTP file |
|
Phone should send the 433 Anonymity Disallowed for anonymous calls |
|
Diagnostic is alway reloaded into the primary slot |
|
Turbo- Speed dial entries not at designated position |
|
Calling/Called Info not correct for SIP TNP phones |
|
Double call sort after ending selected call |
|
ccmuser- add IIS monitor similar to ccmadmin, ccmcip |
|
Can't update phones in cm4.2(3) when all parameters are field |
|
can't update phones in cm4.2(3) - urlscan reject maxquery string exceed |
|
Media Layer Does Not Correctly Establish MasterSlaveDetermination |
|
Transfer to busy user causes Unity port hang |
|
MGCP BRI 3.1 Khz Support |
|
Adding 8.2(1) features to CCM 3.3, 4.1, 4.2, 5.0 |
|
SW MTP/CRA RTP timestamp resets without SSRC changing |
|
SIP Trunk w/o MTP to H.323 w/OFS results in no TCS and no T38 |
|
CFA failing. |
|
AXL addLine and updateLine report wrong error |
|
Callback fails / unreliable when Publisher is down. |
|
CCM releases the call when it receives Status in call_received7 state |
|
NewCall and EndCall should not be mandatory softkeys |
|
BARS not updating CCM03xx DB name in Monitor Disk Space job on Restore |
6608
6608 MTP port intermittently unregistered |
|
6608 T1 CAS ports are getting marked as OOS |
|
6608- Cleanup code to make room for few more fixes |
|
6608- debug enhancements |
|
6608 Gateway gets unregistered after resetting MGCP Backhaul port 2428 |
|
6608 shows wrong OID |
|
COLP not present over SCCP -- H323 ICT -- SCCP |
|
Overlap Sending broken when using redial function while phone is onhook |
|
SDL version change for fix of CSCsf32240 |
|
CCM reporting encodingStyle as ISO-8859-1 instead of an http URL |
|
Dead air for calls that are not processed by application. |
|
CCM service unexpectedly shutdown - access violation |
|
CM 4.1(3) stops Multicast-MOH after receiving an ICMP Dest Unreachable |
|
CCMSNMP does not start on subsriber when publisher is down |
|
Add retry DB Sanity test logic in CCM SNMP agent during initialization |
|
JTAPI CiscoTransferStartEv anomaly when transferring a call to a CTIRout |
|
Address type not updated when JTAPI receives CallPartyInfoChangedEvent |
6608 E1/T1
6608 T1 cas channel rejects outbound calls |
|
ccm core when QSIG-tunneled ICT call is disconnected by remote side. |
|
CCM4.1(3)ES. SQL error when inserting a 7961 phone |
4.1(3)es72
(Base for 4.1(3)sr4d &
sr4b)
RTMT does not work on winos 2000.4.3a or 4.3SR1 |
|
Media Layer Does Not Correctly Establish MasterSlaveDetermination |
|
Meet Me Conference is released when CallManager is down. |
|
Callmanager Fails To Remove First Call Leg During Blind Transfer |
|
CTI shall unregister ssmanager, then register ssmanager at failover time |
|
update/add Phone do not allow userLocale/networkLocale for Cisco7920. |
|
CTIProvider is not closed when WebDialer is deactivated |
|
Jphone software changes to address Memorex enhancements in EDCS-505798 |
|
Support RTCP featurette |
|
Add nightlight features |
|
MGCP GW reset due to message order changed |
|
CCM.exe process shows very high memory usage |
|
callmanager generate same confernceID for h323 gateway call |
|
15 seconds delay when using speeddial for forwarding from AC |
|
JTAPI modified calling party number overwrtten at Route List |
|
SIP trunk stuck in a Shutting_Down state can not be reset |
|
beeps for CFwdAll confirmation and cancellation, 7941,7961,7971 |
|
QSIG-ccm.exe unexpectedly shutdown by overrunning the display[32] buffer |
|
CTI manager running high CPU with CTIERR_DEVICE_SHUTTING_DOWN errors |
|
listUserByName-Bad search filter error if no lastName expr given |
|
CCM tears down all calls on t1-cas trunk if one timeslot reports 5XX err |
|
CtiQbeProviderUnexpected Shutdown after device unassociated with user |
|
CM sends wrong coding standard in Progress PI |
|
JTAPI-TransferEnd event delivered after station/line call cleared |
|
Desktop loses 3rd party call ctrl after consult xfer- personal call back |
|
DM table out of sync..SCCP handling of linkOOS |
|
DM table out of sync..Device manager handling of linkOOS |
|
Maketypes needs run after Product CSV's added to branch |
|
Add 7921 support files (CSV, XML, GIF) to CCM |
|
ST-CCM service could not come up after upgrade |
|
CCM AC-Calls do not come out of Queue |
|
CCM SIP Local Call Transfer encounter no audio with 3rd party PBX |
|
UnknownCallerIdFlag is not checked for calling party number for mgcp |
|
SIP trunk sends two different invites with the same branch ID |
|
T1-CAS MGCP to CM may fail inbound calls but work for outbound calls |
|
Blank directory search from IPMA pages returns 0 users for AD or ND |
|
Removing a line from H.323 device causes CDBLException |
|
Non default device load popup incorrectly lists multiple 7914 loads |
|
CAR tool is not showing destination CMR in CDR> Search by User/Extension |
|
First call to MGCP FXS port fails after CCM service restarts. |
|
Callmanager may get duplicate entries for same region pair |
|
Redial delayed while SDL tracing is off |
|
Calls to a MGCP PRI fail from a H323 device |
|
Blind xfer failure |
|
Call park number is not displayed after getting a new call |
|
Calls fail when CFAll to a CTI RP redirects to another CTIRP. |
|
Agent logoff after xfer creates call on callclosed event. |
|
JTAPI caches invalid Device and Line Handles |
|
always use prime line = true -> on hook dial not working |
|
Cdcc sends SsMoveInd to TransferManager, but ignored due to CSCsc67021 |
|
huntlist hunt option changes do not take effect until reboot |
|
Reset of MGCP Endpoints in CallManager causes failure, after 4.1(3)sr3a |
|
Incorrect Redirecting Reason set to DMS with iDivert to VM |
|
MGCP not passing reason code from PROGRESS to call control |
|
Device Package installation has dialog come up in silent mode |
|
Link 'View the User Guide for your phone' not available for 7961/7941 |
|
Distinctive ring not work when IP Phone has a active call. |
|
High CPU and Code Yellow on CM because of new call loop with vg248 |
|
Callback fails / unreliable when Publisher is down |
|
Calling party number contains number prefix when forwarded to PSTN |
|
Call from PSTN (DMS-100) to Cisco CallManager failed due to NOTIFY msg. |
|
KeepAlive Events (3) To Provide TCP Port Number |
|
Always Route Member not enabled with AXL addAttendantConsoleHuntGroup |
|
7920 Phone Type reported as Unknown in TAPI |
|
TCP Port not closed after open during load test for H323 Calls |
|
MGCP->h323->ipphone call dropped after 8 seconds of being on hold |
|
CCMUser should use FastAccess to get locale information |
|
Agent logoff after xfer creates call on callclosed event. |
|
CM sends Progress message without PI causing PBX to drop the call |
|
Resource Unavailable cause releases PSTN call via H.323 Gateway |
|
Wrong cause code when a call forwarded to Hunt Pilot not answered |
|
CallManager loses CSS for Line so can't route call |
|
7914 Non-default device load only displays 1 module |
|
MeetMe conference leak causes reorder tone on initiating MeetMe |
|
Callmanager won't play re-order tone for Cause 0x809D Facility rejected |
|
Multiple calls with no ring for subsequest calls when a call drops |
|
MonitorPartyTable leak causes continuous appearances of Code Yellow |
|
Add code for RISDC to handle second DBL Exception |
|
960 One button Login Failure with @ character in the password |
|
CM Video-VCB Resource counts not changing for first video participant |
|
CallManager should support RFC3398, or strip ;npdi |
|
JTAPI Gateway receives RESOURCE_NOT_AVAILABLE error |
|
Route/Hunt list is not displaying the correct status. |
|
Synching DBLEnums.asp and .js from share directory |
|
CCMUser can't delete the service URL after unsubscribing the service |
|
Make 7906 (turboprop) appear in device defaults and device pulldown FCS |
|
7906/7911- Checkin user guide and update CSV files for online user guide |
|
Name ChangeCisco Unified CallManager 4.2 - ES/SR Wrapper |
|
QED (CSV and Display XML file) Changes for Phase 2 Ocius 7985 |
|
CIA-680 Support on 3rd gen phones |
|
CCMAdmin should not offer option of 72XX voice platform as a MGCP GW |
|
Calls to BRI gateway from 2nd node fail after 1st node CCM is restarted |
|
Decommissioned Server Not Removed |
|
Intermittently failing to change CFA number by Netwise application |
|
InsertCDR needs to better handle deadlock on calldetailrecord |
|
Non default device load popup does not list load for 7914 |
|
CMR data not being loaded by CAR consistently - Call QoS shows NA |
|
CAR needs to remove loader validation for directory number |
|
BAT does not allow entry of 2 line and 4 speed dial if SD are blank |
|
Importing phones into BAT using a comma in the Alerting Name is invalid |
|
ENU Coltrane3.0 Check In For English-US Locale |
|
AC_J.out.log fills hard drive and 100% CPU for tcdsrv.exe |
|
AC call routed to client remains in queue causing new calls to back up |
|
Transfer fails when forwarded to CTI ports |
|
fwded calls over QSIG to other vendor voice mail go to open greeting |
|
Empty CM Group or Device Pool Insert/Delete Induces CTFTP REBUILD_ALL |
|
multiaccess to CCMAdmin page cause high memory usage of dllhost. |
|
BAT needs to provide a throttle mechanism to control CPU usage |
|
RIS need to handle empty resultset gracefully |
|
CCM 4.1.3 sends StopMediaTransmission for incorrect MOH unicast stream |
|
AdminUtility display a failure message when try to set IWAM_GUEST pwd |
|
Product Specific Configuration Missing from 2821MGCP gateway config page |
|
CTI tries to register notifications after app terminates unexpectedly |
|
Phones,Gateways dont register when cnf cache SP is changed-ctftp |
|
DN config page of 7941G-GE & 7961G-GE shows improper phone icons |
|
7941G-GE & 7961G-GE phone Icons are not shown properly |
|
Find & List Phones Page gives HTTP Error 500 after SR Install |
|
H.323 Tandberg not getting MOH when on hold by SCCP Tandberg |
|
Multiple calls with no ring for subsequent calls when a call drops |
|
JTAPI error -1932787643 when Apps is answering a consult call |
|
Call forward busy on remote node device fails |
|
CM Video Bandwidth Unavailable shows for trunk calls with sufficient BW |
|
CM Location Resync Bandwidth option doesn't resync video BW too |
|
TFTP takes too long to act on the change from Caching to Non-Caching |
|
AXL update of BusyTrigger tag fails |
|
Number OfJTAPI Traces Is Limited To 100 |
|
JTAPI doesn't drop ExternalConnection |
|
Qsig callback and MWI between clusters are failing |
|
Auto Pickup causes incorrect connected name on requestor phone display |
|
NumDevRegExceeded- Number of registered devices exceededPhones cant REG |
|
Forward information is not displayed in a scenario in QSIG |
|
Forward switch fails if forward reroute failed due to no route in orig |
|
participant is not removed from participant list when request rejected |
|
fwded calls over QSIG to other vendor voice mail go to open greeting |
|
Trailing # should be stripped from DivertingLegInfo after call routing |
|
CCM reset due to memory access error in MGCP |
|
Treat auto pickup as a direct call and display From xxx |
|
Error in DeviceManager table leads to False Out Of Resources Condition |
|
Notification Indicator Mandatory IE Missing in DMS NOTFIY message. |
|
After sending ECS, CCM should send TCS after peer closes its channels |
|
DivertingNr should be converted to RedirectingNumber |
|
Max value for Forward Max Hop Count needs to be increased |
|
Delayed cut-through on low bandwidth pipes with shared lines |
|
ART failure adding user to admin group due to referral during ldap Add |
|
CFNCExtCallingSearchSpace shared setting not getting reset to default |
|
AXL listUserByName does not return user with blank First Name |
|
CCM using Active Dir or Netscape Dir Svr AXL search returns no matches |
|
AXL addPhone/updatePhone does not save MLPP Domain value |
|
update/add Phone do not allow userLocale/networkLocale for Cisco7920. |
|
ITA Display of Zero and CAPS O - 7960 Font Display |
|
Dash/Underscore is an invalid char in User Group Base but not for DNS/AD |
|
CCMAdmin page become hung, iexplore.exe runs at 100% |
|
7911 Add support for Vieo |
|
Placeholder CDETS for Turboprop Feature Commit |
|
Enabling or disabling of CFA from IP Phone intermittently fails |
|
7912 Park number is not displayed for a while |
|
Join with on going dial call creates extra conf member |
|
hold-state softkey set not updated on sccp phone in a scenario. |
|
b channels may delay coming in service on MGCP gateway |
|
MaxHoldDurationTimeout requires a restart of CCM service |
|
RTMT reports LowCallManagerHeartBeatRate for all call processing nodes |
|
CDR/CMR Export throws Error if selected date range do not have CDR/CMR's |
|
Export CDR/CMR not working in CAR |
|
Traffic Summary - Day of Month [Monthly] Report is consuming 100% CPU |
|
Incorrect LINE_CALLINFO after lineAddtoConference |
|
Call is not getting cleared ( keep ringing )at all in Huntlist scenario. |
|
CCM stops generating ring-back as it gets H245 LC open |
|
Unable to communicate with DCD when SSL enabled |
|
Some Serviceability Reports are not generated due to java exception |
|
Cannot create new PAB entries from IP phone |
|
Can not see the PAB Entry on Search on Phone for specific Nicknames |
|
Placeholder CDETS for Turboprop Feature Commit |
|
Call placed via 6608 T1-CAS failed when extra digit dialed. |
|
Calls to CTI Route Point fail if CCM group is changed |
|
MLA removes space character from OU name for AD LDAP access |
|
CCMAdmin IPMA config with AD fails if directory query time out |
|
CMM Echo Cancel Coverage 8 and 16 ms should be removed |
|
Back out CSCsb60395 change in ConnectionMediaManager |
|
Incorrect 'srcinfo' in Admission Request from CCM, for forwarded calls |
|
Optimizations for CIPT uses incorrect ConfigDB |
|
RTMT generates directory connection and replication alarms |
|
Call transfers over ICT between clusters ring fast busy of dead air. |
|
E-mail information erased after PAB entry edited on phone |
|
User unable to edit PAB entry if nickname crosses 26 character |
|
Unable to allocate PAB entry to PFD service if nickname is >16 character |
|
Fast dial from an ip phone 7960/7940 fails for 24 digit numbers |
|
unable to add fxs port to a route group |
|
Trunk Configuration Page displays productType is 77 below ctrl buttons |
|
Incorrectly versioned CiscoCTL Client plugin checked in |
|
No DevSpecific event notifications after losing connection with CTIMgr |
|
MSSQL remains in |
|
CFNA/CFB External not working for T1 CAS or BRI loopback calls |
|
CCM send internal conference bridge number as the connected party number |
|
Calling and called parties were swapped in CcSetupCompReq and CcSetupRes |
|
No StationOutputStopTone When Onhook Speeddial Matches Overlap RP |
|
H.323/ICT conf resource not released when rx empty terminalcapabilityset |
|
CTI unexpectedly shutdown more then 16 party ad-hoc conf with CTI device/line monitoring |
|
CTL client returns 'No valid server certificate found' |
|
Transferred calls to ac pilot are stuck in queue |
|
calls to the AC pilot are being rejected with available HG members |
|
Call details orphaned in broadcast queue when transfered from Unity |
|
Intermittent missing TransferEndEv for some calls |
|
CCM unexpectedly shutdown w/ access violation in SoftkeySetMask--SetSoftkeySet |
|
Calls to the ACPilot get stuck in queue until manually released |
|
Call to Pilot Point from SIP trunk fail |
|
Mistreating incoming TCS data capabilities as video capabilities |
|
Skinny (G729)-CCM-MGCP calls fail intermittently |
|
CM strips first digit of PRI DMS Original Called Party Number |
|
Find/List Trunks-Search RP by % works like IsEmpty |
|
Unable to login IPMA assistant console |
7940/7960
7960 phone does not clear status line during reset |
|
pressing line button on ipphone doesn't switch between detail &overview |
|
Posting Line34 URI enables Line30 on ip phone. |
|
7960- Does not preserve the state of mute/spkr button in handset mode |
|
7960 drops the incoming call when using the IPICS services. |
|
7960 phone does not handle HTTP code 401 for push request |
|
Phone- Authentication username/password takes only 31 characters |
|
CiscoIPPhoneInput takes * and # when input is set to N |
|
StreamingStatisticsX not backwards compatible |
|
7960- Call being on hold is NOT sorted by Select function |
|
7960- Doesn't update CDP cache when no voice vlan present in CDP message |
|
7960 DSP Logging utility broken |
|
7960 does not display via |
|
IP reassembly broken |
|
IP phones become unregistered from both SRST and CM |
|
7960/7940 phone stuck at CONFIG IP after a reset/power cycle |
|
Phone load Upgrade to 7.2(3) causes RXshort errors on PC port |
|
Phone drops untagged PC Traffic |
|
HTTP 100 Continue from phone malformed |
|
Remove use of linked directory in SCCP BA |
|
7960 - XML Debug PUSH behaves erratically |
|
Handle Current Call missing when dialing from Directory |
|
Phone rejects menu responses from server- Fastdial, Corp Dir |
|
Callback notif (Dial) & Park while already in an active call fails. |
|
GARP enable/disable ignored |
|
The phone unexpectedly shutdown when it receives invalid Response.ContentType in HTTP |
|
Secure Phones does n't cancel tftp request while cancel key is pressed |
|
7940/60 PC port 100M does not receive network traffic intermittently |
|
7960/7940 Rcvr Lost Pkt reports as a negative no under impairement |
|
Unable to dial the CB notified number during ringing state |
|
No sidetone during first phone call following phone registration |
|
Phone performs unneeded ARP when Garp enabled |
|
Phone removes ARP entries too quickly |
|
help for settings button not displayed when setting key is disabled. |
|
DHCP enabled Phone resets with held call when alternateTFTP changed |
|
Phone doesn't display held call in detail view when barged call ends |
|
Promts is Truncated to 20 Characters when using Greek Locale |
|
Phone resets if we dial Half of the DN on-hook & remaining off-hook |
|
Speed dial from Monitor DN is not working with 7.2.2 |
|
phone display Remote-In-Use menu when the other end resume the call |
|
DIALED Number missing in CFA where the target phone is 7940/60 SCCP |
|
Update 7960 built-in font to include new zero with a slash |
|
7960/40 cannot register in autheticated mode CCM 4.1.X OS 2000.4.2 |
|
Phone resets during high bandwidth traffic to PC |
|
Placed calls are recorded on all shared line phones |
|
Missing SpeedDials on phone after upgrading the phoneload |
|
7960 unexpectedly shutdown when more than 20 calls placed via stress script |
|
Placed call list under directory gets updated only for Connected calls |
|
7960- Unable to reset phone when other shared line is busy |
|
Phone strip dialed Number in Directory Placed call list for PSTN call |
|
Phone without DHCP cant recover Dup IP address |
|
7960/7940 characters by pressing '0' with li-ffr.4-1-3-JPN are funny. |
|
help symbol missing in text press - key to cancel for english locale |
|
7960 Settings -> RingType menu changes doesn't take effect |
|
7910 DSCP values need to be consistent with current design guides |
|
EM logout restarts the IP Phone. |
|
Small MTU causes CVTA to H323 video call failure |
|
7960/7914 Ringer type off by 4 lines. |
|
Update dictionary file with SeaDragon new phrases |
|
Phone Continuously displays Requesting RingList File ...... |
|
Phone UI Lines separating the DN disappear as it failover to subscriber |
|
http///CGI/CallInfo does n't display all lines call Info. |
|
ActiveSoftkeys eg redial, New Call are shown when pubisher CCM is down. |
|
In CallInfo the CalledPartyName field is not proper for Conf call |
|
In http request for CallInfo/LineInfo the Prompt field is showing null |
|
Line button does not answer call with 2 calls on hold already on line |
|
DHCPReleaseMessage should be unicast to DHCPserver,not on broadcast IP. |
|
7960 Phone doesn't display blank URL sign or URL without label on line |
|
Volume control keys when calling a busy no affects ringer(ver8.0(0.16)) |
|
7960 Phone reset from settings with **#** while on call hold |
|
7960 Phone loose RTP stream when restart from CM |
|
7960 Pressing Line button twice ends calls on Phone in ringing state |
|
BigApp does not kick back to LA on version mismatch in XMLDefault.cnf.xm |
|
phone 7940/7960 should escape '#' symbol |
|
7960 doesn't receive MOH or DHCP when Voice VLAN = Access VLAN |
|
RED LAMP indication on 7914 for In Use Remotely does not work - 7.2(3) |
|
7960 MWI functionality should be consistent with current phone behavior |
|
7960 Phone volume not being set properly at RTPRx start |
|
Menu object as IDL URL, menu item 1 selected when phone goes off-hook |
|
MWI lamp glows continuosly after a CB notification for the first set CB |
|
IP phones become unregistered from both SRST and CM |
|
Phone drops untagged PC Traffic |
|
Secure Phones does n't cancel tftp request while cancel key is pressed |
|
7940/60 PC port 100M does not receive network traffic intermittently |
|
Unable to dial the CB notified number during ringing state |
7914
Implement 5.1 features |
7985
The phone does not honor the Connection Monitor Duration fallback value |
|
Phone may malfunction if more than two lines configured. |
|
Telnet xstatus command under DNS/Domain Name contains non-ascii letters |
|
Need to add support for IP phone service |
|
IPMA is not supported with 7985 video phone |
|
Add screen saver to 7985 |
|
XML support |
|
Three or more line appearance needed |
|
Ocius should have a contrast and white balance configuration options |
|
save button placement cause user to end call |
|
Directories menu does not display for 15 seconds when URL is unavailable |
|
Background image support is required |
|
Phone unexpectedly shutdown when 100 calls active and remote side is lost |
|
7985 does not play the MLPP premption tone |
|
Settings Erase softkey is displayed even when config is locked |
|
7985 video endpoints do not support services. |
|
Packets from the PC port are not being forwarded out SW port |
|
7985 unexpectedly shutdown when attempting to originate a call from WebDialer |
|
Phone does not ring at all if the selected ring tone is not available |
|
Error message on missing ring tone is different than 7970 |
|
Phone never boots up when background image is changed |
|
Phone does not detect changes to the CM background image list file |
|
7985 does not do Authentication for CiscoIPExecute |
|
7985- HTTP redirect not work |
|
7985- CiscpIPPhoneIconMenu oject parse error |
|
7985- HTTP refresh not work |
|
7985- two items missing from phone's web access page |
|
7985 not display Authentication URL on Device Configuraiton menu |
|
7985 should have Power Save Configuration menu |
|
Device ID in CDP messages should all be in upper case |
|
7985 takes too long to re-register when image load is not found |
|
7985 not back to power save mode if restarted from CCM |
|
Alpha Numeric fields use different key mappings than other phones |
|
7985 not back to power save mode after a call coming in |
|
7985- phase 2 image does not support asp URL pushed to the phone |
|
7985 should exit Service app after login w/ ExtensionMobility |
|
7985 (X) button toggles between Full Screen and Overlay modes |
|
7985 only shows 6 lines w/ Privacy and Speedial configured |
|
7985 does not display To conference at line button menu |
|
Callback activation tone is not heard when using TFTP Server 2 |
|
7985 not registered to its CCMs |
|
7985 not update call status icon at line button menu |
|
Hanging up the phone does not work when failover occurs during call |
|
7985 unexpectedly shutdown when Execute Object is pushed to phone with proxy config |
|
7985 got authentication error |
|
7985 can not list PAB entry |
|
7985 displays white line at full screen |
|
7985 does not send out video packets w/ IPMA configured |
|
There is no Cancel softkey when requesting a phone service |
|
Berbee services do not work on 7985 |
|
Softkeys in the Berbee phone service do not work properly |
|
MyGroup IP service returns back John Chambers' group instead |
|
7985 should exit from Setting menu by pressing Setting button |
|
7985 Error message different when URL DNS name error |
|
7985 unexpectedly shutdown when wake up from power save mode |
|
7985 incorrect behavior when get HTTP Error 404 |
|
Camera Properties need a wider range of changes |
|
When upgrading the software the status line is stuck |
|
Left/Right arrows should change the monitor brightness values |
|
7985 could not display FastDial page |
|
7985 Update at service page does not work |
|
Phone unexpectedly shutdown while looking at the eventlog during an active call |
|
Video between 7985s momentarily blurs out |
|
7985 unexpectedly shutdown while answering a call |
|
Remote side video stops working when hold/resume rapidly pressed |
|
7985 should close the listening chanel when service app is closed |
|
Exit an IP phone service returns the user to the top of the service list |
|
Phone takes DHCP option 150 in the wrong order |
|
Conference call info status is displayed as the the 4 instead |
|
Digits after first call state softkeys are messed up |
|
Calls for status line is corrupted after pressing directories button |
|
The From status line displays no number on an incoming call |
|
|
|
Phone should drop from full screen mode during an incoming call |
|
7985 Push Execute failed with Internal Error |
|
7985 unexpectedly shutdown w/ call on hold |
|
7985 does not disable SSH after reset |
|
985 fails over to SRST after ethernet cable replugged in |
|
7985 does not change Camera properties back to default value |
|
7985 should not display Erase key at CameraSettings menu |
|
7985 plays wrong Ring Tone |
|
7985 does not save selected Ring Tone if RingList.xml not available |
|
HELP ID- Help for Camera Settings returns help for Monitor Brightness |
|
HELP ID- Brightness Hue Saturation help returns main help topics instead |
|
7985 set button template wrong w/ one button set as None |
|
7985 unexpectedly shutdown when access Help Main menu |
|
7985 fails to display Video Mute icon when incoming call answered |
|
Video mute line status icon is lost after a hold/resume |
|
Placed Calls Directory entries have a %s as part of the display |
|
Background & Ring don't reset when Restore Default Settings is involked |
|
Downloaded Background & Ring list missing when TFTP Server 1 is down |
|
7985 unexpectedly shutdown when Line key pressed on Help Menu |
|
X button does not work in Service w/ Host Not Found Error |
|
No Help Info for Transfer softkey |
|
No Help Info for NewCall softkey |
|
No Help Info for More softkey in onhook state |
|
No Help info for Dial and Cancel softkeys in onhook dialing state |
|
No Help Info for NewCall sofktey in Remote-In-Use mode |
|
Softkey sets mess up after access Help in Callback mode |
|
No Help info for ImmDV and TrnVM softkey in ringin state |
|
7985 should include Camera Setting info on View Setting menu |
|
Forwarded to status message not display the DN |
|
7985 displays ?1001 status message when in Setting menu |
|
X New Missed Calls should not persist w/ new incoming call |
|
7985 does not support Restricted Setting Access |
|
Phone unexpectedly shutdown pressing the Search softkey on Corporate Directory |
|
Next softkey does not work in Corporate Directory |
|
Wrong softkeys when looking at an empty Missed Calls list |
|
Cancel softkey has no impact while downloading Background images |
|
7985 play ringer to handset for a second call |
|
Softkeys disabled after change audio source w/ Handset off the crack |
|
Forwarded Call Infomation Display not as configured |
|
Softkey sets changed after pressing Line button |
|
7985 should switch back to the first call after 2nd disconnected |
|
7985 behavior inconsistant with 2nd incoming call |
|
Wrong softkey sets for barged call |
|
7985 displays Remote-In-Use icon after barge into a call |
|
First ring tone in ring tone list is the letter a |
|
Cannot easily answer incoming call while in Missed Calls Directory menu |
|
7985 call status message mess up for shared line |
|
7985 shared line Call Info display different from other phones |
|
7985 should initiate a new call on shared line by selecting the line |
|
7985 not show the CallInfo of shared line on line menu |
|
Dial key not work on FastDial |
|
7985 should always use first avail. line for Dial from Directory |
|
7985 should allow number with 25 digits at PAB |
|
7985 not fallback to primary CCM if the CCM restarted |
|
7985 does not have Next Softkey at Berbee main menu |
|
No Update softkey for graphicMenu and image |
|
7985 not work with directory.asp |
|
7985 fails to display No Park Number Available |
|
PAB service URL does not work |
|
ExtensionMobility ServiceURL button not work |
|
IP Phone service - My Group does not work properly |
|
7985 flash light not blinking for Callback |
|
Denial of Service tcpsic script unexpectedly shutdown the 7985 |
|
Personal Address Book edit Name returns 400- Bad Request |
|
7985 not display Softkeys with position more than 5 |
|
7985 could not display Directory object with maximium value |
|
7985 unexpectedly shutdown when pressing Softkey-Next and Softkey-OK |
|
Phone does not recoginize SoftKeyItem/Position object |
|
7985 gives parsing error with IP Phone Agent Service |
|
7985 unexpectedly shutdown when running a image slide show IP service for 10 minutes |
|
Fast Dial phone service should be allowed to Assign up to 32 digits |
|
Call Information is not displayed after pressing Settings button twice |
|
7985 gives incorrect Error Code for XML parsing error |
|
Phone help does not work |
|
7985 gives ParseError if IPMA realtime update stopped |
|
7985 unexpectedly shutdown when press Exit at IPMA assistant service |
|
7985 does not display Exit key w/ Parsing Error |
|
Phone does not fallback off SRST router after call is terminated |
|
7985 unexpectedly shutdown when attacked with some Denial of Service scripts |
|
Phone displays a ? instead of line feed on directory listing output |
|
Blackjack IP phone service returns error after 1st key press |
|
IPPA service Agent Login screen password entry is displayed in the clear |
|
Phone directs some http requests to the proxy url when it should not |
|
PC Voice VLAN disabled does not work |
|
Line button not work if not all line buttons are assigned |
|
7985 should change focus to the active call after exit from Setting menu |
|
No Help ID for IPMA related softkeys |
|
Softkeys are confusing when in the Lines menu |
|
Cannot hang up a call when the call comes from a shared line |
|
IPPA service briefly displays some XML code during start or state change |
|
7985 unexpectedly shutdown with broadcast traffic at Voice Vlan |
|
HELP ID- Background Image help returns Help Topics instead |
|
One way video or black screen or no video over VPN observed |
|
7985 XML input - Uppercase & Lowercase input types allow invalid chars |
|
7985 XML Input - Some Input types with password field flag show password |
|
7985 XML Input - Equation type input doesn't allow symbols |
|
7985 should exit from Service app by Exit key w/ EM login page |
|
Could NOT hangup call on shared line after restart |
|
7985 New HW does not suppress upstream Broadcast, multicast traffic |
|
7985 video phone unexpectedly shutdown when it receives cisco gateway fax NSE |
|
QED (CSV and Display XML file) Changes for Phase 2 Ocius 7985 |
|
7985 not support softkeyitem as Key-KeyPad |
|
Berbee IP phone service returns- unable to display service error |
|
7985 should not clear Status object |
|
7985 should not append its Devicename in HTTP Get messsage |
|
Softkeys under the settings menu are misaligned |
|
Phone status log should contain more information |
|
One way video seen on call between 7985s |
|
Ringing stops playing when the volume is adjusted during incoming call |
|
Phone is using the callback tone as a ring tone on next call |
|
7985 reboots if Option 150 is a String Data-Type |
|
7985 XML Input - equals character (=) looks like a solid, heavy dash |
|
Audio sources do not work on next call after a failover with call active |
|
Cannot change audio output source when failover with active call occurs |
|
Error message is truncated when invalid Admin VLAN is entered |
|
Localization needs to be turned off on the phone |
|
Softkeys are unavailable after pressing the Window button |
|
Help for Power Save Configuration returns help for Camera Settings |
|
Help within the Power Save Configuration returns Main Menu Help instead |
|
Help of SW Port Configuration returns help for PC Port Configuration |
|
Stock quote IP phone service unexpectedly shutdown the phone |
|
Domain name cannot be entered when phone doesn't have an IP address |
|
HELP ID- Power save configuration returns help for Display On |
|
Network Configuation Default softkey should be renamed to Erase |
|
User Preferences Default softkey should be only available when unlocked |
|
The popup window after pressing Default should be more specific |
|
7985 - Power save exits XML Service (and menus) |
|
Configuration parameters domain name and DNS servers lost after upgrade |
|
Phone rebooted when using Hoot & Holler with 2 phones in Shout mode |
|
Phone ignores DHCP option 150 when option 66 is present for TFTP server |
|
Domain Name shows up as - ? when it is not populated by DHCP |
|
Onhook dialing does not light Speaker LED in SRST mode |
|
On help button ? page, Back softkey doesn't work |
|
Requesting better administration tools |
|
Video pixelation on calls made between Cisco VT Advantage and 7985 |
|
7985 Improper system message wording |
|
There were no tones heard when using onhook dialing |
|
No notification on phone when the remote end of a call is lost |
|
Call focus switches off active call when shared line is used by others |
|
Default router field periodically resets when phone is configured |
|
7895 may report multiple Standby CCMs after fallback |
|
Phone does not ignore lower valued Voice VLAN when multiple CDPs recvd |
|
Phone may stop ringing when switching to a second incoming call |
|
Headset mode sends output to the Speaker in SRST mode |
|
Sometimes cannot answer 2nd call by switching lines in SRST mode |
|
Phone sometimes does not direct audio to the handset in SRST mode |
|
Call Forward icon still displays when fallback to SRST mode occurs |
|
When using EditDial of a number the prompt should start at the beginning |
|
Rarely the MWI light is on even when no messages are pending |
|
Phone does not send periodic CNG packets during long silence breaks |
|
Call Waiting Ring setting will only Flash the MWI lamp during 2nd call |
|
Video may freeze at end of call or in self-view mode |
|
Switch should ignore PC Voice VLAN Access when there is no voice VLAN |
|
802.1p frames dropped on phone with Admin VLAN and PC voice VLAN disable |
|
Phone gets stuck in CallManager Unavailable state |
|
Test script causes a watchdog timer expiration |
|
Packets to PC port are re-mapped with 802.1p when Voice VLAN is 802.1p |
|
EditDial followed by lifting handset will not dial call |
|
Phone may continue to display Self View rather than idle screen |
|
Denial of Service mutant script cause the phone to reset |
|
Sometimes phone cannot end call after a CCM fallback with call active |
|
Web Access Enabled/Disabled need to be added to CCM and phone |
|
Phone sometimes does not connect to correct backup CCM during fallback |
|
Phone does not reset when lower numbered Native VLAN learned |
|
Video mute state get out of sync after the phone is restarted |
|
Phone sometimes shows wrong status msg/softkeys after CM service restart |
|
Cannot browse under Directory, Up/D rocker stuck at the Missed Calls |
|
Phone drops ~50% of IP multicast traffic from SW to PC port |
|
7985 MWI Light misbehavior |
|
7985g reboots after select softkey then hit the X key |
|
7985 does not play precedence call waiting tone |
|
7985 phone does not display call pickup visual alerts |
|
7985 unexpectedly shutdown when running Codenomicon TCP protocol verification suite |
|
7985 phone reboots when pressing the 'Directories' or '?' buttons |
|
CCM4.2 - Cisco 7985 Phone softkeys disappear during Pickup Audio Alert |
7906/7911
7906/7911 Check in 7906/11 f/w load to CCM |
7935/7936
DTMF tone will not play for consecutive same digits with 7936 |
7920
Coltrane 3.0 Firmware Check-In |
Digital Access WS-X6608
6608 Incorrect marking DSCP value to 0 |
|
6608 shld not automatically clr connection when ICMP unreachable is rcvd |
7935/7936
Cannot use # or * as first entry while onhook |
|
7936 vulnerable to ICMP attacks |
|
7936 doesn't send HTTP Get with multi tier DNS names in Directory URL |
|
Can't place a call from phone book when it receives a missed call |
|
Phone cannot be reset to factory default when Admin passwd is not known |
|
Remote party hears echo when 7936 used in glass conference room |
|
7936 accepts invalid IP Address and Subnet mask |
|
7936 accepts invalid Alternative TFTP Address |
|
Access Admin Setup without entering the passcode |
|
Web interface allows to change password with different characters |
|
7936 Web Interface allows different characters in Phone Book |
|
7936 Web interface doesn't prompt for password when phone is restarted. |
|
7936 phone retains the meetme session even after the call manager fails |
|
phone may not give Error tone when incorrect phone number dialed |
|
7936 Editing phone Book doesn't have the asterisk in the required field |
|
If call received while editing ring tone and publisher fails, 7936 hangs |
|
7936 Web interface accepts alphabets in |
|
Phone will not accept incoming call while waiting for |
|
7936 Takes long time to register when PINGED with CCM failover |
|
Info for |
|
Polycom 7936 allows to change the Ringer settings in Ringing state |
|
Phone book entry on the web display is not proper |
|
7936 reboots when you configure Admin VLAN id while in active call |
|
7936-Call Transfer number is not displaying in SRST mode |
|
Park Information retained for a long time. |
|
DN not displayed while placing the call on hold & initiating a new call |
|
Call initiations fails from the phonebook with CFwdAll |
|
Phone registers with Alt TFTP when Alt TFTP Address not specified. |
|
Phone hangs when used Diagnostics with CCM failover |
|
Mute turns off in this scenario in 7936 version 3-3-7-0 |
|
Second Call on shared line cannot be resumed or muted |
|
7935 & 7936 Polycom phones lockup on failover, loss of call preservation |
|
Display issue when Meet-Me number is 10 digit |
|
Phone does not accept to change the passcode with valid characters |
|
incorrect display on one of the phone in sharedline |
|
Incorrect LED status on a phone in sharedline with call waiting enabled |
|
7936 won't fallback to a TFTP server once registered to an SRST router |
|
7936 Phone use odd RTP port numbers |
|
7936 phone with phone load 3-3-8-0 does not work for FAC |
|
7936 Outside dial tone sounds the same as inside dial tone |
|
Call gets disconnected if we press hold & resume multiple times |
|
7936 does not play tone 50 (Zip) when someone joins a conference |
|
Phone display is incorrect when a bogus phone load is entered. |
|
Phone doesn't ring when **8 is executed |
|
Phone hangs during failback and failover with meetme |
|
Phone displays Registering after CCM failover in a active call |
|
Dial tone stops when phone receives a missed call |
7941/7961-7970/7971
no value for some items on Device INformation page |
|
Phone should display ... for very long Text or Number |
|
SSO Standby RP T/B atm_ha_decode_vc_update+0x23c for ATM PVC bundle |
|
Phone registered to a CM 3.3 shows only one line while call on hold |
|
Received and missed calls show wrong calling party number |
|
Time stamps on console messages and phone display is not the same |
|
Deselected call in sorted call list appears with other selected calls |
|
Turbo Gabage at the end of Network Statistic screen |
|
Cancel softkey has delayed response when looking up a bogus DNS addr |
|
Phone resets wmore volume of call are placed on sidecar lines |
|
wbm failed to extract signature when display filter was used |
|
Turbo Can not remove Doamin Name on phone |
|
Phone does not remove the default router config |
|
Increase max CPU usage timeout for JVM process |
|
SIP TNP 1.1 image stress run freezes phone UI |
|
Phones unable to Rx or Tx Multicast Services when Publisher fails. |
|
Phone w/200 calls active single line reset w/calling phone reset |
|
dhcp.conf could have invalid my name entry |
|
Add consolle trace to indicatie the call is an encripted call |
|
Phone doesn't register when it is unable to resolve the CCM name |
|
paging group display delayed on 7911 with CME |
|
get SW port returned -1 error after downgrade to 6.0(2)SR1 |
|
Phone stops playing multicast after an unanswered call |
|
local Ip/port value is cleared but others are kept for an ended cal |
|
LED does not blinking red while the DCP is busy |
|
7970/7971 Touch Screen issue IP Phone URL shows Delay |
|
ogins with sys group permissions on release signed phones |
|
timeZone tag errors |
|
Background Image thumbnails not displayed in correct order |
|
7961 Row of Pixels missing on Line View graphic |
|
phone locks up when SEP dateTimeSetting is empty |
|
phone locks up when SEP dateTemplate is MM/DD/YY |
|
Phone display goes blank for consult transfer to busy monitor line |
|
when PickUp softkey is pressed on onhook phone displays ??? |
|
Service URI cause phone to unexpectedly shutdown |
|
need to press mute twice for an incoming intercom call |
|
Assign a same IP port to RX and TX socket - casues 1 way audio |
|
Phone doesn't play Zip/ZipZip Tones toward network |
|
Phone Rcvr Lost Pkt reports as a negative no under impairement |
|
SIP TNP DSP debug seen when pressing Settings, Directories, or Services |
|
Reference getPegs() via IMedia interface instead of directly |
|
Turbo Phone receives mcast pkts when port open forMcast transmit |
|
Turbo Error Verifying Config Info after LSC install on secure phone |
|
README-SGM-pdsources on DVD has SGM references |
|
Phone Should handle gethostbyname failure and print appropriate Err Msgs |
|
Phone not displaying all Placed call list when pressing up/down button |
|
Corporate directory search fails if username contains special characters |
|
wirelss client to client can not pass traffic |
|
Service URL feature assigned in em profile does not work |
|
Phone sends Duplicate DHCP Discover Message |
|
Phone freeze after reset stress |
|
Phone displays wrong msg when registration rejected for security reason |
|
phone doesn't show up old admin vlan id in Current Admin. VLAN Id |
|
Corporate Directory Search Fails When using Russian Locale |
|
Add Title to Line View to identify which line the calls belong to |
|
Having directory menu open causes Callback to not working properly |
|
HTTP CGI ModeInfo query does not return if Services URL doesn't resolve |
|
Ethernet Disconnected Mesasge does not appear when Ethernet unplugged |
|
Turbo Missing status messages on Load Server parameter |
|
No status message when TFTP service is down on load server |
|
LineInfo web age query does n't show up Messagewaiting Indication. |
|
Phone won't failback to a TFTP server once registered to an SRST router |
|
HTTP req canclled msg when hitting a softkey |
|
Japanese locale (td-sip.jar) not loading on SIP phones. |
|
Removing JVM from 7.0 on 8.0 CPK files (to avoid out of space errors) |
|
Turbo status message No Default Router after changing DHCP=no to yes |
|
Phone does not preserve the state of mute/spkr button in handset mode |
|
Skittles phone does not complain with junk value in displayOnDuration |
|
Making DSP standalone on phones- dsp.cnu reads dspfw.bin |
|
select image Userpreference->Background image display invalid png icon |
|
CDP unexpectedly shutdown from broadcasted CDP pkt, results in restart of all apps |
|
Privacy lamp is not being displayed correctly on 7941 SCCP phone |
|
Phone unable to come out of Service Menu using CANCEL softkey |
|
Phone responds to CDP triggers from upstream port |
|
phone does not play precedence CW tone |
|
Calls drop during CME failback |
|
Phone is stuck if Encrypted Config is on and supporting load is absent |
|
phone doesn't come up with DHCP enable when Voice VLAN = Access VLAN |
|
Incorrect response for unicast/invalid IP adress for RTPMTx i p URI |
|
CiscoIPPhoneExecute ExecuteItem priority 1 is ignored in some cases. |
|
Invalid Ip Address to be displayed while validating Null values. |
|
Turbo lost audio w/ 100% broadcast traffic |
|
Status Msg timestamps changed between 24hr/12hr formats on reset |
|
CP-7970 firmware version 7.0(1) distorts background image color |
|
Softkey changes from Connected Transfer state to On Hold state |
|
Phone is loosing the querystring parameter on the refresh |
|
Phone Multicast services not working |
|
LSC Installed Status Messages is not displayed on phones |
|
cBarge Target phone changes focus when other party cBarges |
|
Phone doesn't dial from placed call listwhen editdial& dial is pressed . |
|
Phone Displays UI with no keys for a shared line scenario. |
|
Phone CGI URLs never complete HTTP transaction |
|
Services page text does not display properly |
|
Idle phones never send SCCP TimeDateReq to sync clock |
|
Pressing the '.' soft key in the edit menu doesn't force Kate String T/O |
|
Clicking noise is heard in encripted call when duplicating packets |
|
Phone plays garbled audio for PA prompts |
|
phone displays ??? as Codec in Call Statistics window |
|
Call Stats window displays wrong info for Rcvr Lost Pkts/Discarded |
|
IP Phones use random UDP source port for RTP media |
|
Phones stop sending KA when backup TCP link down |
|
call bubble does not disappear when there is no active call |
|
High End Phones connect to CCM sub that is not present in the CTL file |
|
Turbo fine-tune displaying errors of dspSendFrame _framePutEgressFrame |
|
Turbo InsideDialTone could not be stopped after removing CFwdAll |
|
UDI Support |
|
Turbo Codenomicon HTTP test 39730 causes sunvm CPUTime Limit Exceeded |
|
Add core file decoded core file to the serviceability webpage |
|
SIP phone loads and CCM are out of sync for PC Voice VLAN Access |
|
GARP enable/disable reversed |
|
Property Errors - Settings Can Be Lost |
|
phonerebooting when secondary CME inaccessible and keepalive is 10 |
|
Enhance the flush operation in the RecordStore |
|
HTTP Client locks up upon consecutive posts to CGI Execute |
|
No prompt/status in Detail call history record |
|
Dial Softkey Enabled when no Active Audio Path or no CCM |
|
Erase from Top-Level Settings Menu does delete sidecar contrast |
|
SIP Phone does not do a TLS session reuse after network failure |
|
RMS Store must be deleted in order for phone to boot correclty. |
|
Phone stuck after erase under Settings menu |
|
JPhone Overview displays incorrect topcall if some RIUs made private |
|
GARP enabled native code returning incorrect value |
|
Phone could not recover after DNS entry be corrected |
|
Phone sends Invalid Message for SCCP v3 and v4 |
|
Phone Answer softkey not displayed for new icoming call |
|
Remote In Use Icon/LED not shown when shared line is private |
|
HTTP Authentication Does not Show Response |
|
Able to Change Ring Volume Even when Setting Access set to Disable |
|
TimeDateReq to sync clock causes KeepAlive to miss one interval. |
|
7970/7971 InCorrect Date Format Shown Under Missed Calls |
|
2 meg file limit cause double boot when upgrading to 8.0 load |
|
JAVA/TNP Log/trace related changes |
|
CNU syslog changes for 7.0.2.x branch |
|
getportcfg check for errors on msgsnd() |
|
Display distorts, when held calls goes from three to two |
ATA18X
ATA SCCP Incorrect Call Waiting behavior |
|
Conference to ATA-Phone thru H323 & ATA-phone on same CME doesnt work |
|
ATA flooding callmanager with SoftkeyeventNew call skinny messages |
|
Problem transfering calls using ATA and CME |
|
Update signaling ToS to be consistent with current design guides |
|
ATA186 configuration web page should state clicking rather than click |
|
ATA SCCP sent AVT message when sent DTMF to SCCP endpoint |
|
No Secondary dialtone played by ATA SCCP |
|
ATA186 excessive TCP ACK delay after receiving SKINNY message |
|
ATA SCCP sends excessive StationSendTimeDateReq |
4.1(3)es40
(Base for 4.1(3)sr3c, sr3b, &
sr3a)
Max CDR Records exceeded if SQL Agent service is not ready during init |
|
MGCP-Need configurable timer waiting for FXS onhook when call ends |
|
CTI manager running high CPU with CTIERR_SHUTTING_DOWN errors |
|
CiiscoatUserProfile and ciscoatUserProfileString not updated |
|
Missing disconnect for conf parent in alerting/drop scenario |
|
Firewall support for attendant console in skate |
|
Remove Redundant FORWARD Trace Events in CCM SDI Trace |
|
Unanswered call to Huntlist is cleared with incorrect cause code |
|
Race Condition Occurs in CCM that Causes Call to Get Dropped |
|
Support of DDI trailing |
|
CM need support for new phones in devicelistx.asp file |
|
Tunneled protocol not available for H225 gatekeeper controlled trunk |
|
CTL client returns 'No valid server certificate found' inserting etoken |
|
ES/SR Installation needs corresponding code for CSCsb44801 resolution |
|
stopservices needs error handling update |
|
Enlarge splashscreen in ES/SR installaton |
|
Need new sections for file copy ops |
|
Update SQL script handling |
|
Enhance error handling reporting and dialogs |
|
End of installation Dialog Changes needed for Device Package |
|
Sub installation failed because no user tables for CCM database on Sub |
|
CCM 4.1.3 sr1 sending Mal-formed DNS request |
|
PRI Sends Cause Code 0 On Drop Party From Conference |
|
H.323 Sends Cause Code 0 On Drop Party From Conference |
|
E164 Mask change notification issue for DNs with wild characters |
|
CCM does not update analog port status for analog GW (need rej msg) |
|
CAR report CDR Search by Gateway displays incorrect records |
|
Implement group listening. |
|
Changes in clearcase not properly built into ES |
|
Stopservices to display services being stopped. |
|
CVTA Failed call to MGCP BRI gateway - bearer cap 0x8080A5 |
|
CCM MGCPbrid device didn't handle CcSelectFacilityReq message properly |
|
|
|
CCM doesn't sent stop alerting tone |
|
CallBack does not work after modifying the CallManager Group |
|
Race Condition Occurs in CCM that Causes Call to Get Dropped |
|
CTIManager unexpectedly shutdown with Access Voilation |
|
raven Voice Quality Problems using SIP based VoIP |
|
AXL response containing junk characters. |
|
Cisco TFTP perfmon counters can not be viewed through perfmon |
|
Slavonic Languages Delta on the localized dictionaries |
|
JTAPI Client causes issues with ICM Jtapi Gateway |
|
PlatformException sent to Apps erroneously when call is xfer'ed/dropped |
|
JTAPI is not sending CiscoAddressCreatedEv |
|
WebDialer takes line with lowest DN on user device porfile |
|
PCM change breaks 4.2 and lower builds. |
|
Need tag for 6608-MTP/CFB in ccm xml |
|
Callback seizes to function after a while |
|
log service stopped event in SDL traces |
|
Call Manager restart setting up media for MGCP call |
|
Locations Bandwidth Leak |
|
CCM Can not form the TO packet that is required by LCS |
|
ES34 causes global directory pages to break |
|
AdminUtility does not write out a log file |
|
AdminUtility should control password changes for the IWAM_Guest account |
|
AdminUtility is not stopping services |
|
enhance adminutil to validate usernames |
|
enhance adminutil to be compatible across Cisco CallManager versions |
|
enhance adminutil to perform additional operating system checks |
|
enhance adminutil to reset dcom permissions |
|
Translated Rerouting Text not shown on phone |
|
Sending Complete Setup Msg to overlap Route Pattern fails |
|
MTP Orphaned Stream w/H.323 Call On Hold - Incorrect CI |
|
Call fails to connect after dialing FAC code in a scenario |
|
There is no StartMedia Transmission to the IP phone when it re-opens |
|
Bandwidth leakage allocation in CCM |
|
Hunt group was not utilizing the T1 CAS circuits on a Gway until reset. |
|
ccm.exe terminates unexpectedly after trunk reset w/ DNS server offline |
|
Softkeys greyed out for a barged call that is barged again |
|
Need Inbound Redirecting Number IE over QSIG PRI for interoperability |
|
T38H323-H323 fax arcoss CCM nodes not supported |
|
Preserve active H323 GW call during quiet clear |
|
CTI Route Point is using the configured DNas Redirect |
|
|
|
updatePhone - invalid Max Call and Busy Trigger causes line disassoc |
|
log service stopped event in SDL traces |
|
Disable Nonregistered SCCP Keepalives default value should be False |
|
DialingForestDumpEnabled service param should warn of CCM terminations |
|
BAT Phone validation fails with comma in Display or Alerting Name |
|
Deleting Unassigned DN with BAT causes deletion of configured devices |
|
CCMAdmin Password Validation should be proper once enabling MLA !! |
|
Region name fields should allow 30 character in regionconfig.asp |
|
Changing partition name not implemented until CSS is changed |
|
Route Filters can not be selected when Max List Box Items is exceeded |
|
CCM Inter-Cluster Trunk Wait for Far End H.245 Terminal option |
|
Inbound Redirecting Number IE Delivery should be selectable for QSig |
|
No validation done if beginning DN is empty in VM Port wizard |
|
TAPS should be made compatible with CRS 4.0 |
|
VG224 configured for shared line on Callmanager fails |
|
devices attempting to register prior to CCM being up |
|
Unable to complete the conference |
|
CTIManager out of service making PhoneLine to go into incorrect state |
|
Cisco IP Voice Media Streaming App using SW CFBs stops unexpectedly. |
|
updateGatewayEndpoint fails after insert 24 ports |
|
Error comes on clicking Update on Autogenerated Device Profile |
|
Remote scripting error on web page if updated after long idle time. |
|
Blank popup message after session timeout popup |
|
7.0(2)SR1 image for the 7941/7961 checkin to 3.3, 4.0 and 4.1CCM release |
|
7970/71 7.0(2)SR1 image check in |
|
Add online doc. name to 7911 SCCP loads |
|
Stndrd Feature 7960 sftky profile fail on 7940 CallBack equipped phone |
|
Update/Make 7911 ready for FCS and prepare Skate SR build |
|
AgenaInterface leak when remotely join party |
|
Last party in the meet-me conf closes if other parties has Tx failure |
|
ccm.exe unexpectedly shutdown when printing Media_PayloadList[capsInB[5].payloadCapabil |
|
CCM Initialization-Forward Phase In SsInit Takes 34 Minutes To Complete |
|
race condition in CTI failover/failback |
|
CallManager forwards conferenced call to default VM Profile |
|
CCM Init/RuntimeDETAILED DBL Trace For FORWARD Phase Is Too Verbose |
|
CCMAdmin Read Only User Can Escalate Privileges |
|
Unauthorized Alteration of CCMAdmin Administrator Privileges |
|
CCMAdmin Read Only User Can Escalate Privileges |
|
CCMAdmin Read Only User Can Escalate Privileges |
|
MeetMe needs to have additional tracing to track leaks in conf use |
|
CTIMnager unexpectedly shutdown access violation |
|
Dialed Number Analyzer fails after NZT Daylights Savings Time Start |
|
invalid GSM EFR audioUnitSize should not cause CCM not to send TCS |
|
H.323 Faststart call fails after getting 2 ORCAck from IOS gateway MTP |
|
CM sends ARQ with nonzero bw for callback via GK controlled ICT |
|
CFwdALL may fail to clear for Shared DN |
|
ASTISAPI.DLL Memory Leak Upon CMLAUserPermission--setUserID() Failure |
|
Call Pickup fails on Hunt List |
|
Application menu items should not be in all CAPS |
|
CAR version 4.1(0.34) cannot retrieve data passed certain dates |
|
Moving clOck forward cause JTAPI Exception and Provider going OOS |
|
App Event log Warning not always generated when CM service stopped |
|
CCM sends sendTCS to device registered in h323 gw mode |
|
Call forward on QSIG reroute fails |
|
Aupair Sustained CPU Spike - ghSendQueueSem Deleted On CCM Change |
|
remove loggingDisplay option for 7941...7961G-GE phones from CCM/Windows |
|
RUS-JTAPI files shows garbage in the preference window |
|
JTAPI deadlocks when trying to deliver event at same time agent logs out |
|
Invalid DisconnectedEvent in conference release |
|
Cisco JTAPI does not work with IBM JVM 1.4.2 |
|
Address on CTIPort is out of service if registered after adding observer |
|
InvalidStateExceptionImpl when jgw attempt to send call to CTI manager |
|
Support new phone cert in CAPF |
|
ToneOnHold played when user drops from external call |
|
CallManager unexpectedly shutdown (access Voilation) in Cdcc |
|
CCM 4.1(3)sr1 - SIP trunk Diversion info lost |
|
QSIG Loops on CallForwardAll to OffNet DN |
|
Callmanager propogates disconnect cause 0x9F |
|
Logging Display and Load Server features do not appear for the 7970/7971 |
|
Adding DN get stuck in Verifying state |
|
Attendant Console fails to redirect Queued calls to Huntgroup |
|
Attendant Console gets an error message Failed to make new call |
|
AC outbound call does not use primary line |
|
OrininalPartyName and LRPName coming blank in inter-cluster unpark |
|
LineTransferEndedEvent Missing because of CallProcessing Issues |
|
DSP Keepalive Timeout for MOH Multicast |
|
Memory leak in AgenaInterface |
|
ccm.exe unexpectedly shutdown (access voilation) with CcSetupCompReq |
|
add service parameter for progress->disconnect translation |
|
CTI does not query database as part of ProviderOpen |
|
VPT receives corrupted HTTP header in AXL response |
|
|
|
Call Manager 4.0(2a) SR2b unexpectedly shutdown when masking called pattern |
|
Q931 field does not contain release cause for Annex M1 calls |
|
CMI service does not restart when it loses DB connection |
|
Stuck call |
|
BAT insert fails if phone description contains comma |
|
Unable to update MLA's User Group Base. |
|
Route Group page takes too long to display available devices |
|
Diverting to specified directory number isn't working |
|
Stored procedure was not replaced correctly on Sr1 Installation |
7911
Checkin 7911 f/w loads to create Device Packs for FCS |
7902/7905/7912
7912 fails due to malicious VLAN tagging |
|
7912 does not play |
|
7905/12 phones lose Service button after EM update |
|
phone - 7912 phone reboots after receiving 3 IMs quickly |
|
Only a 7912 shared number phone work when configured max-dn dual-line |
|
No dial tone after the 7905 and 7912 SCCP failover to SRST |
|
7912G-A phones cause PC's behind them not to retain an IP Address |
|
Long delay for PC to obtain network connectivity when used with 7912G-A |
|
7912/05 should always Reset unless an rtp stream is active |
|
CCCM 5.0 & 7905/12 does not show external number on top line of display |
|
7912 SCCP sends excessive StationSendTimeDateReq in idle mode |
|
7912/05 excessive TCP ACK delay after receiving SKINNY message |
|
7912/05 RTPMTx sets TTL of sent multicast packets to 1 |
|
Timedate req. msg. storm from at midnight |
7920
Extension Mobility does not work with Services URL Button on 7920 |
|
7920 Doesn't Support Vibrate URI |
|
Need a menu to display configured regulatory domain |
|
Need a menu to display current transmit power |
|
7920 Does Not Support CCA Versions of QBSS |
|
7920 can spontaneously re-register to CM in idle with INF-MIB error |
|
7920 Can Associate to a Lower Priority Profile When Set to Auto Profile |
|
Upgrade to 2.0 will cause phone lock password corruption |
|
CCM 5.0 Centralized TFTP compatibility enhancement |
|
Port 17185/udp is open on 7920 phone |
|
7920 RTPMTx sets TTL of sent multicast packets to 1 |
|
7920 call-forward noan on second active call results in phone hanging |
|
7920 can corrupt the CCKM Timestamp |
|
Invalid XML object sizes can cause the 7920 to reboot |
|
Idle URL can cause the 7920 to lock up |
|
7920 will roam off a strong signal AP to a weaker one |
|
7920 should continue streaming RTP packets when on Mute |
|
7920 can fail to ACK G711 packets during a call |
|
7920 Can Roam More Frequently With 12.3(7)JA AP Image |
|
7920 Can Stop Scanning Although Still Associated |
|
7920 send 802.11 Auth suddenly and it causes choppy audio |
|
Channels in Active List are not flushed after 3 missed CM Keepalives |
|
Emergin's alert tone volume needs to be limited when on-call |
|
CP-7920 is not responding to AP packets |
|
MWI tone can be very loud to user if CP-7290 re registers |
|
Need to roam when QBSS max threshold is met |
|
7920 MR2.0.1 firmware upgrade |
7936
7936 Transmit Jitter Extremely Sporadic - 2 Second Cycle |
7935
CP-7935 generates choppy audio when in a conference call |
7941/61
The Exit softkey is not working on the Callback screen. |
|
Privacy lamp is not being displayed correctly on the phone. |
|
Add fault-tolerance to file system. |
|
checkin 7.0(2) firmware for 7941/7961 phones into CCM/Windows |
7970/71
7.0(2) firmware for 7970/71 |
6608
CallManager may incorrectly put a 6608 CAS port OOS |
|
6608-Glare conditions on T1 CAS is not cleared appropriately |
6608 E1/T1
Calls through 6608 T1 CAS trunks are not preserved |
|
T1-CAS E&M ports on a 6608 card unregistering during stress test |
|
Periodic T1-CAS E&M channel out-of-service during 6608 stress test |
6624
change configuration link is not opening for 6608 & 6624 GWs. |
4.1(3)es25 (Base for
4.1(3)sr2)
High cpu with ccm, cti and gatekeeper configured |
|
CCM faulters on backhaul messages to 6608 for T1 CAS hookflash transfer |
|
Put PerfmonQueryAllCounter ASTIsapi Url back to 4.1.3.sr.1 |
|
Enable Database Related SYMBOL and MAP Files During ES/SR Build |
|
Delay on DN lookup in CCMAdmin with large number of CallPickup Groups |
|
Route Group Configuration screen does not show Available Devices |
|
CM SDLListeningPort service parameter should not allow a value of 0 |
|
CCM CCMG for inter Cluster Trunks does not limit GK registrations |
|
Established Flood causes high CPU usage or unexpectedly shutdown ccm process |
|
Can't save IPMA mananger's config if divert target contains number zero |
|
CallManager-improve handling of idle TCP connections |
|
TCP connections not managed aggressively |
|
TCP connections not managed aggressively |
|
CAR 4.1(X) CDR search getting Database access denied |
|
MGCP calls fail after failover |
|
AVVID ICT media exchange timeout on CTI redirected call |
|
LDAP Access Error while searching for users in CAR (clone of CSCsa60661) |
|
Wave driver thread leak |
|
One-way audio with CiscoTSP |
|
Callback doesn't work after CTI Manager failover |
|
PC logging option is not available for makaha |
|
CCM AXL API support for voice mail pilot and profile |
|
Invalid PSS1 info may cause ccm hang |
|
Incorrect DNIS using speeddial and Route Pattern configured for overlap |
|
CNFA on hunt group pilot point doesn't work for transfered calls. |
|
CM doesn't wait for more digits if partial digits are rcvd for RP/XP |
|
CCM rejects incoming T1 CAS calls intermittently due to race condition |
|
1 way speech path call from CME FWD to operator transfer to ip phone |
|
Add 7985 QED support CCM versions 4.X and 5.X |
|
7911 QED changes to support alt scripts and load server |
|
Endcall Received After Second Transfer Causes Disconnect |
|
New Call Failed To Be Pickup Using Handset |
|
Auto pickup call does not show forward info after connect |
|
RQNT before CAS DT/oc interruptted DT/sup |
|
IpVmsApp on Subscriber pegs to 100% CPU |
|
Checkin ip7961.pdf ver3 into3.3.5.eng.spec, 4.0.2.eng.spec, 4.1.2.eng... |
|
CallManager terminates unexpectedly, RaiseException |
|
TFTP Does Not Build All Configuration Files |
|
Subscription Pull Takes Almost 6 Hours To Complete |
|
Wrong call details on shared line console |
|
Unwanted error pop up on console with shared lines.. |
|
The line state is broken when using dialrules.XML |
|
Enable visibility of Makaha types in dev packs 3.3.5.eng.spec, 4.0.2. .. |
|
Inband info not heard by IP phone when ISDN DISC+PI received after SETUP |
|
Inband announcment not heard when calling busy or unallocated numbers |
|
Secondary line set to flash only will only blink the icon and not lamp |
|
Need to bump the SDL version number due to changes in CSCef64304 |
|
7961/7941 font should be more readable - suggest making tallerCSCef28642 |
|
Device Association Page distorted & JScript Err after a bad search |
|
MLPP config not available for 3845 MGCP gateway |
|
On 7970 Display-on-Time shows default value after setting it to blank |
|
Station stay at CONNECTED state after call release |
|
Media Component Race Condition Leads To MRM And Process Leaks |
|
Primary CMI does not send KeepAlives to Voicemail |
|
Change Notify stops working due to bug in TcpLib |
|
Second TCS from H.323 Tandberg is not handled properly by CCM |
|
dtmf not sent on t1 cas If call is not in connect state |
|
Ericsson MD110 PBX CCBS/NR CallBack Interoperability issue |
|
Standard Phone FG does not Allow Changes to EM Select User Profile |
|
MLA generates error when configuring partition for DN |
|
Install Migration for AIM-VOICE-30(332) to AIM-VOICE-30-SLOT-0 (412)fail |
|
InsertCDR.exe taking 1.5 GB of Memory |
|
CCM Srvce Unexpectedly Restrts during a fax operation usin H.323 gateway |
|
CCM SIP call failed when the INVITE message has a phone-context tag |
|
Pilot point busy if member sets CFDWall back to Pilot Point |
|
Agent stuck in talking after Outbound Option call |
|
4.0(2) wrong line status returned by jtapi |
|
selectRouteThread and EventThread are blocked for 15sec. |
|
Cisco Jtapi stops sending events after address is manupulated byCCMAdmin |
|
CATUrgent need to get JTAPI build to Catalan theater with revisions |
|
TurboError Extracting File using latest tc-sccp.jar file |
|
AC client showing wrong line status |
|
Device Pool not getting updated for 7912 and 7905 phone. |
|
CallManager terminates unexpectedly, RaiseException |
|
InsertCDR service stops populating CDR database from flat files |
|
Implement JAVA side and QED CM interface |
|
Catalan fail to launch due to wrong language code in localelistings.prop |
|
Idivert Key upon being pressed get temp fail |
|
LowAvailableVirtualMemory alert triggers when 70% or more memory free |
|
Unable to manage Personal Address book via CCMUSER page |
|
DevPack does not install the locale files |
|
No alarm when maximum devices per provider is exceeded |
|
No alarm when maximum devices per node is exceeded |
|
Deleting a transcoder disables transcoding for the whole cluster |
|
CCM doesn't clear the h225 call properly when PSTN hangs up |
|
CDR value is not correct when using Auto Call Pickup |
|
Comment Column In CallDetailRecord Table Does Not Support 2048 Chars |
|
Enable fclosethread or start CCM w/ thread corrupts SDI index to -1/0 |
|
Wave driver incrementing RTP sequence #s during silence |
|
Additional languages for CM4.1(3) |
|
Marker Bit not set in the first RTP packet after silence. |
|
Change notification stopped working after route filter change |
|
CFA stops working after CCM has been running under load |
|
IP phone re-registers after set or unset of call forwarding |
|
Add QED support for 7911 |
|
AC displays err message during preemption on an attendant phone |
|
Pop message when pressed save on the Attendant console GUI |
|
Attendant Console shows Unknown Error at Basic Settings |
|
Polycom ViewStation Call disconnects |
|
CC returns unmodifiedCGPN same as CGPN. Issues with states of agents |
|
High number of voice packets/frame in outbound fast start |
|
DMS-100 spec does not recognize ISDN Q.931/Q.850 Disc Cause Code 53 |
|
Incorrect cause code is returned when the line is not registered |
|
Always use prime line is not working with 7.1.2 phone load |
|
Messages button works intermitently |
|
AS-8 gateway stops supporting SMDI after upgrading to CM 4.02a |
|
Call Pickup fails intermittently |
|
CCM prepened the prefix to Cgpn for CLIR calls via H.323 GW. |
|
CM Deducting twice the Audio BW and returning only half when call comple |
|
CCM doesn't instruct 6624 to generate outside dia ltone |
|
h323 faststart to MGCP calls fail when h323 has active caps enabled |
|
unexpected shutdown in MeetMeConference when accessing NULL pl/spl lists |
|
CTI Change needed to accomodate CCM Change required for Prime Line |
|
RBT is not heard on the PSTN side while call routing to an agent |
|
ForwardManager does not remove map table (mPartyToActiveCallIndexMap) |
|
MWI requests fail when originating device goes onhook quickly |
|
CTINewCallAcceptTimer expires during lineRedirect causes timing issue |
|
TCD is requesting redirect to an available hunt group member, calls fail |
|
CallManager terminates unexpectedly during IP Phone registration |
|
RTMT installs outdated/duplicate/unsupported JRE 1.4.1_01 |
|
TFTP not serving requests, stuck with 200 requests in progress |
|
CNF stops sending CTFTP changes. |
|
7961 device pack doesnt conatin proper device name on device default |
|
Unable to access Database also Publisher out of Disk Space |
|
AXL Allows Creation of |
|
ADCM Tools will not function w/multiple clusters in same AD domain |
|
Directory throwing exception when manager DN does not exist in iPlanetDirUser, UserManager |
|
Call Activity Report incorrect reporting on PRI count in service |
|
java.exe consumes 100% CPU leading to CallManager restart |
|
Validation not done for Auto-registration Information |
|
Unannounced products show up in various admin pages |
|
Garbage characters on JTAPI Preferences launched on Japanese PC |
|
Misleading message in JTPrefs console window. |
|
Need a reason/cause for the CallCtlConnFailedEv to indicate MLPP |
|
Unexpected CallCtlTermConnTalkingEv after disconnected |
|
Error on phone page in DNA |
|
Patch Install says file replaced successfully whether done or not |
|
Msg if we wish not to view log should be consistent for install/unin |
|
SR doesnt Init Database on replication failure detected scenario |
|
Device Default is updated when uninstalling ES/SR |
|
Wrong Upgrade Message when upgrading to SR01-rc02 |
|
Unwanted msg leading to err pops up while upgrading to 4.0(2a)SR01 |
|
Misleading CCm Ver Msg if Patch installed on a Non-CCM Server |
|
SR Patch Ver check lists From as old SR and not new MR and misleads |
|
Remove the extra are-you-sure from the ES/SR installs |
|
Uninstall Confirmation dialog should mention version reverting to |
|
Support needed for Ext Device Package execution during ES/SR install |
|
Need to dump a list of running processes during installation. |
|
CCM 4.0(2a) - DCD terminates during quiesce operation for backup. |
|
AXL missing a few key handlers |
|
Attendant Console does not retain window focus |
|
Need to add Service parameter Always play outside dial tone |
|
Enhancement to Modify APDU ext num for outgoing Qsig MWI on/off messages |
|
Call Forward to Multiple Busy Users gets no busy tone |
|
Pressing the Transfer softkey on a selected call deselects the call |
|
Annex M.1 trunks need to optionally ignore tunelled content |
|
Call Join Request fails |
|
When Auto Call PickUp IP Phone does not display For. |
|
First character of Caller ID is stripped in Japanese environment |
|
CCM constant registrationRequests to GK if no TTL in registrationConfirm |
|
No ringback tone when calling from CME to Qsig PBX via CCM |
|
CTI Route Points remain registered after CTI application shutdown |
|
CTI unexpectedly shutdown when device is removed from control list |
|
Unnessecary changenotification sent to DeviceLineMgr causes CPU load |
|
LDAP Access Error while searching for users in CAR (cloned CSCsa64436) |
|
CM hangs on blank screen upon reload with USB mcast MOH audio src |
|
Error -1 [Internal Error] Unknown user on 7940 when adding Fast Dial |
|
1700 GWs FXO ports are allowed to be configured for diff signaling. |
|
ONLINE HELP Ring tone help screen needs to replace Alert with Ring |
|
ONLINE HELP Device Configuration help need updated with new submenus |
|
ONLINE HELP Help info for editing IP address needs addtional steps |
|
ONLINE HELP Erase softkey help under Settings needs more information |
|
ONLINE HELP Help for Network Settings DNS Server 1 returns error |
|
ONLINE HELP Default softkey under some User Preferences returns no help |
|
No Help content for the softkey OPickUp. |
|
Greyed ERASE softkey is actually enabled |
|
Caller ID gone from shared line after a barge |
|
> in 7940/60 i-button help text |
|
sidecar lamp shows red for barge/cbarged calls |
|
7960/40 Device Info page does not follow Message Waiting Lamp Policy |
|
Display settings on Phone should be changed for Restricted Display |
|
7960 can load a Ringlist.xml with more than 50 entries |
|
Remove conditional code |
|
IPPS authentication credentials, % sign not URL encoded |
|
PC can't ping 7960 phone with dot1p configured |
|
fclose thread flag should be set to true by default to avoid cpu spike |
|
CM disconnects call when phone goes off hook |
|
CM Cas trunk in cm shows registered without NMHDV in ios router |
|
illegal line errors in CCM log? |
|
CallManager terminates unexpectedly,need to handle exception in dbprocs |
|
CCM sends 2 StartMediaTransmi Msgs without a StopMediaTransmi between in |
|
7960-7914 does not ring on incoming call if there is active call on 7914 |
|
Not receiving NOTIFY, Called Party Number is not displayed properly. ICT |
|
CallControl Should look at all the Fac IE's in the CfDataInd signal |
|
ReleaseComplete CRV High Order Bit Not Flipped |
|
Admin page does not open after installation of SR1 Rc02 |
|
Unable to have a NON-QSIG ICT in a mixed routelist |
|
CCM unexpectedly shutdown intermittently on changing the CCM server's timezone |
|
Can not add more than 39 Devices in Media Resource Group |
|
Unable to delete IPMA assistant in Catalan locale |
|
Video capability for Communicator has to be added |
|
support for EM2-HDA-4FXO in CCM |
|
CallManager ARQs for wrong E.164 address when calling H.323 client |
|
AXL AddRegion does not support Default Codec With Other Regions |
|
AXL return unknown error for updatePhone after IP service got deleted |
|
StationUpdateCapability from VTA doesn't list all codecs in CCM Trace |
|
Flow control is not symmetric if one video location is unlimited |
4.1(3)es06 (Base for
4.1(3)sr1)
Maketypes needs run after Product CSV's added to branch |
|
Change default value for Disable Non-Registered SCCP Keepalives to False |
|
TSP access violation with CCM 4.0 |
|
802.1x auth state remains after PC disconnect |
|
Incorrect status msg when no ctl on phone and modified ctl dwnld |
|
7960/40 does not support QueryStringParam as documented in SDK |
|
IPSvcssupported xml fields size are 1 less than max |
|
IPsvcNew http headers support as per SDK 4.0(1) |
|
Lock icon overlaps to page title text |
|
Mid-call video starts when active call is in mute state |
|
Phone shows encrypted call with CM 3.3 |
|
Security Configuration menu name should be separate from title |
|
Clear softkey doesnt clear interface stats on HTTP page |
|
Autodial fails on choosing hold option for the current call |
|
Not able to scroll down to see help pages displayed by i button |
|
7940/60 phone should use HTTP 1.1 for URL with IP address |
|
Auto line select enabled prevent use of softkeys on 1st line |
|
7960 stuck in booting process when press service before phone alive |
|
7960/7940Voice Quality Degradation With Echo Back To Remote Party |
|
Shared line call doesnt display toggling between lines correctly |
|
Support calloc caller PC broke LA built. |
|
Phone connects to secure SRST if bad config |
|
Clouseau debug infrastructure implementation in 7960 sccp phones. |
|
Retain old BA while LA upgrade |
|
Disable the display debug tracing by default on 7960 phones |
|
Update copyright year on mid-range IP Phone boot display |
|
After a preserved calls is terminated, the phone is stuck |
|
Key rollover with Hold and EndCall Softkeys causes wrong action |
|
7940/60 stuck in Configuring CM List state |
7940/60
Video stream not terminated when CM is down Bsphere 2628 |
|
NetworkConfigurationX tag names do not match Network Config UI |
|
Help for side car buttons throw an error |
|
IPSvcssupported xml fields size are 1 less than max |
|
Lock icon overlaps to page title text |
|
Idle URLRefresh page does not recover after a packet loss |
|
Phone accepts invalid/Reserved/Multicast IP address |
|
invalid display by ip phone on key pad uris push |
|
phone not updating volume changes during call preservation state |
|
Handle current call not displayed on dialing from directories |
|
pressing first line speed dial causes second line to go offhook. |
|
No PORT_UP event on 7940 if PCport on Phone changed frm 10Mbps-100Mb |
|
phone sends tftp request to ip address 0.0.0.0 |
|
Phone does not retains Volume Settings changes |
|
7960/40 phone will not fail back to primary |
|
Change in behavior of resuming the call that is onhold on IP Phone,7.1.2 |
|
speaker button won't work with sidecar |
|
7940/7960 display HTTP error[11] when pressing Services/Directory button |
|
Key rollover with Hold and EndCall Softkeys causes wrong action |
7970/7971
Some items of Streaming Statistics from 7970 inconsistant w/ 7960s |
|
Headset status indicator incorrect after 7970 reboot |
|
7970 incorrect LineType for some line buttons |
|
7970 not auto answer with headset after restart w/ headset light on |
|
7970 not put active call in focus after incoming call disconnected |
|
Phone restart with lower line rate of multicast/broadcast traffic |
|
7970 fails to reregister after temporary WAN failure |
|
Ringer volume and other parameters are not configured aftr DSP reset |
|
Sidetone on handset after reset |
|
7970 ICMP hard errors behavior changes |
|
7970 does not pick up the line when configured share line |
|
Extra ring heard when answering call after adjusting volume |
|
7970 RTPRx/RTPMRx URI syntax error allowed |
|
Possible deadlock situation in msg queue software |
|
Phone stuck at Configuring IP after prolonged CCM disconnect/recon |
|
7970 drops host in DNS queries with subdomains |
|
Skate Security config menu opt 5 and 6 display wrong softkeys |
|
7970 RTPRx/RTPMRx URI opens invalid port by default |
|
Phone lockupCSCeg04380 |
|
7970 gethostbyname() does not return multiple IP addresses |
|
Mute signal heard on network |
|
When resetting the phone (**#**) PC loses network connectivity |
|
phone freezes during reboot with mqThread problem |
|
7970 phone failover to SRST takes more than 6 minutes |
|
Last digit not displayed when dialing from keypad |
|
JavaException using Navigate Keypad when call on hold |
|
Phone continue to stay with Requesting msg, cancel key has no effect |
|
Java exception when 7970 configed with sidecar but none attached |
|
7970 Phone hangs on changing existing speed dial from phone (CME) |
|
7970 unexpectedly shutdown when access protected URL 2nd time |
|
Onhook Dialing will not accept * or # as first digit |
|
Core dump of Sunvm.cnu when web-access is disabled & then enabled |
|
Attempt to load diagnostic image file causes CNU reset |
|
Onhook Dialing is available when the phone is not registered |
|
7971 Multicast traffic dest to PC dropped by switch in phone. |
|
RTPTx Stop not being executed |
|
7971 Unplugging and plug the ethernet cable, looses VLAN id |
|
Incorrect time for |
|
7970 drops keys if pressed too fast |
|
EM logged off profile keeps CFA icon |
|
Update handling of init.conf authentication settings |
|
SA Dereferencing pointer to freed memory in Core/CNU/NetSys/udp.c |
|
SA expression must be a modifiable lvalue in Core/Apps/cmds/ttrace/ |
|
SA Freeing pointer to already freed memory in Core/Apps/daemons/DHC |
|
Broken autosensing on type-2 cabling (BU-3494) |
|
Makaha power request numbers are wrong |
|
ListenerManager allows for multiple listener |
|
Memory leak when press keys in predial |
|
Memory leak on startup in Call History property |
|
7971 phone not upgrading load, using device defaults. |
|
Phone reloads from nmap connect scan |
|
Stream.c flood reloads phone |
|
Failover fail on 7971 phone with CM 3.3.4(SR2) |
|
CVTA with 7970 messes up audio caps |
|
Phone stuck at Updating Software |
|
7970 - does not report Dest Unreach on sendto() |
|
Ethernet Disconnected message interferes with display (BU-3572) |
|
EndCall softkey doesnt work when CM down and other end had hit Hold |
|
7971 Low power backlight needs to be 14 |
|
7970 - only retries 4 times after leaseT1 expires |
|
7970 hangs at config IP after reset |
|
Unexpected DHCP Renew after Release operation |
|
Shared System Threads create debugging problems |
|
Cut through on speaker phone take approx one sec |
|
Line button becomes useless after try dialing from call history |
|
Timer object should allow ITimerListeners to disable timerCancelled |
|
7970 phone does not close the sockets automatically |
|
Mid-call video starts when active call is on mute |
|
7970 registering with CM when a active call is in place |
|
7971 phone reset after hold/resume duration |
|
Phone freeze after the extension mobility duration test was run |
|
7970 hangs intermittently while attempting EM login/logout |
|
XML parse error when text object with 4000 chars of text is sent |
|
Multiple restart from CM causes phone to freeze up |
|
http push may stop working |
|
Console shows CONSOLE TOO SLOW! Skipping 0 log files! |
|
Trace does not include key press information |
|
7971 Phone ignore vvlan information from switch port |
|
CVTA does not receive information on calls active when PC plugged in |
|
Phone stuck after erase operation |
|
7971 does not comply with 802.3af power specification |
|
Phone can lose VLAN id with broadcast storms in the network |
|
PC attached to Phone loses network after multiple phone reload |
|
7971 phone re-boots when SYNC_RCVD state sttack was run |
|
Enable 802.3x flow control |
|
7970 plays loud comfortable noise when using G.729 codec |
|
Can not accept calls when call history is empty and in focus |
|
7970 change between daylight and standard time 1 hour too early |
|
Ringer stops working if press speaker right after adjust ring volume |
|
Phone restarts exposes memory leak in the CallAgent module |
|
Call Info gone but voice path remains after brief Ethernet disconnec |
|
Phone does not take Service URL w/ no label |
|
7971 w/ PC connected not operate in low power mode using ieee inline |
|
7970 does not display missed call info after waking the display |
|
Phone stuck under simClient duration test |
|
7970 not alllow user to set IP Address Release as No |
|
7970 should display IP address released |
|
7970 missing date on console logs, status messages & debug display |
|
7970 Autodial postpends to dialed # if display name contaions #s |
|
UI issue services tab not coming to foreground in push scenario |
|
7971 continuously resets if dot1x configured on switch interface |
|
Services Changing volume while RTPRx - softkey gets stuck at Save |
|
shownet command in cnush gives wrong output |
|
7971 accepts untagged packets while on a voice VLAN |
|
AbbrDial softkey appears on 7970 phone in CM3.x |
|
HTTP Push requests has successful response, but UI does not display XML |
|
7970 does not properly reset causing sessions hung in LAST_ACK on CCM |
|
7971 PC port does not show what is configured |
|
CP-7970 Fails to Boot up if 'switchport voice vlan dot1p' is configured |
|
Bad voice on 7971 phone with 10% broadcast traffic |
|
Broadcast traffic throttling rate very low w/ load 69 on 7971 phone |
|
7971 phone only allows 10M (1%) broadcast traffic send to PC |
|
Phone does not pass thru all multicast traffic to PC |
|
7971 switch port stops transmitting frames causing phone to unregister |
|
Network Statistics does not display Port 1 or Port 2 status information |
|
7971 - PPU workaround does not set forced link speed correctly |
|
7971 - change CDP from a mgmt packet to a mcast packet in ATU |
|
7971 - enable VLAN 1 and VLAN 0 |
|
Phone unexpectedly shutdown with in half an hour ,when XML boundary objects script was |
|
Phone unexpectedly shutdown for 200 calls per device case |
|
7970 won't boot w/ inline power |
7905/7912
TFTP Client Busy Retry Behavior |
|
7912 doesnt display correct Softkeys when using MCDN feature |
|
IP Phone 7905 not responding to http commands |
|
7912 cant ring immediately when receiving a call after fallback |
|
MWI will be turned off by incoming call |
|
7905/12 display English prompt at Services page |
|
7912 ignores StationClearPriNotifyMessage from CME |
|
Authentication delay between IP Phone 7905 and CM 5.0 is to long |
|
Issues with processing of DNS packets |
|
7912 RTP URI push during call requires user to cycle hook twice to end |
|
7912 dies when configuring Graphics via TFTP on CCM 4.1 |
|
During cross upgrade, power off/on the phone & the phone never come up |
|
Found dtmf digits fail when calling into Meeting Place IVR. |
7920
BSSID is all Zeros in Reassociation Packets |
|
Site Survey Detail Shows the Same Info for All APs Sometimes |
|
7920 Does Not Answer IGMP Query |
|
7920 Could Get Into Continuous Roaming |
|
7920 May Get 1 Way Audio Without ARP-Caching |
|
7920 Will Sometimes Show RSSI = 1 |
|
Packets are Sent at 1mbps rate Off Call When 7920 Uses a Non-Auto Rate |
|
7920 Advertises All Rates Are Supported When Non-Auto Rate Is Configured |
|
Get association timeouts sometimes with Aruba APs |
6608
6608 Fa Relay debugs in D00404 firmware need to be same as D00403 |
|
6608 inbound call mistaken for hookflash |
|
ICMP Hard error handling |
|
Dicktracy Remove unnecessary DSP and MLPP related messages. |
|
6608 Dicktracy Reduce trunk flash timer from 700ms to 400ms. |
|
Burst of static during ringback and connect on calls through 6608 |
6608/6624
Integrate 4.3.25 DSP firmware for 6608 |
6624
6624 FXS port is unavalable for 2 mins after disabling and enabling |
|
updation on 6624 does not reflect on port configuration page. |
|
FAC tone played continuously on using non default network locale |
4.1(0.46) |
|
ASTIsapi.dll |
3.3.2.0 |
Aupair.exe |
4.1.3.20019 |
AuthFilt.dll |
4.0.0.0 |
BulkAdministrationTool.exe |
5.1(4d) |
CallBackService.exe |
3.3.2.3 |
ccm.exe |
4.1.3.20735 |
CcmServRtmtPlugin.exe |
4.00.0002 |
CiscoAttendantConsoleClient.exe |
1.4.1.246 |
CiscoCTLClient.exe |
2.1(222) |
CiscoJTAPIClient.exe |
2.1(3.28) |
CiscoMessagingInterface.exe |
4.1.3.10026 |
CiscoTSP.exe |
4.1(1.4)ES12 |
CPidMgr.exe |
3.0.0.0 |
ctftp.exe |
4.1.3.20013 |
CtftpChangeNotify.dll |
4.1.3.10054 |
CTIManager.exe |
4.1.3.20025 |
DBConvert.dll |
4.1.0.11 |
DBL.dll |
4.1.3.20009 |
DBLRT.dll |
4.1.3.20008 |
DBLX.dll |
4.1.3.10034 |
DNASetup.exe |
4.1(3)ES |
InsertCDR.exe |
4.1.3.20018 |
IPMAAssistantConsole.exe |
14.0.0.162 |
Ipvmsapp.exe |
4.0.0.20 |
IpVms.sys |
4.0.0.25 |
MADirectory.dll |
1.0.0.1 |
MediaAppPerfMon.dll |
|
QRTFileMgr.exe |
4.1.3.10080 |
RisDC.exe |
4.1.3.10057 |
RISX.dll |
3.3.0.2 |
SnmpCcmImpl.dll |
4.1.1.2 |
SOAPISAPI.dll |
4.1.3.10083 |
SSAPIDLL.DLL |
4.1.3.10025 |
tcdsrv.exe |
1.4.1.13 |
ToolforAutoRegisteredPhonesSupport.exe |
5.1(4b) |
UpdateLoadInfo.exe |
4.1.0.11 |
UserPermissions.dll |
4.0.0.0 |
Firmware |
4.1(3)
Devpack 71 |
7914
14-Button Line Expansion Module |
S00105000300 |
Analog
Access WS-X6624 Load |
A00204000012 |
ATA18X |
ATA030203SCCP051201A |
|
C00104000002 |
Digital
Access WS-X6608 Load |
D00404000030 |
IP Phone
7902g |
CP7902080002SCCP060817A |
IP Phone
7905g |
CP7905080003SCCP070409A |
IP Phone
7906 |
SCCP11.8-3-4SR1S
|
IP Phone
7910 |
P00405000700 |
IP Phone
7911 |
SCCP11.8-3-4SR1S
|
IP Phone
7912g |
CP7912080003SCCP070409A |
IP Phone
7920 |
cmterm_7920.4.0-03-02 |
IP Phone
7921 |
D00404000031 |
IP Phone
7921G |
CP7921G-1.1.1 |
IP Phone
7935 |
P00503021700 |
IP Phone
7936 |
cmterm_7936.3-3-14-0 |
IP Phone
7937 |
apps37sccp.1-1-1-1 |
IP Phone
7940/7960 |
P00308000800 |
IP Phone
7941/7961 |
SCCP41.8-3-4SR1S |
IP Phone
7942/7962 |
SCCP42.8-3-4SR1S |
IP Phone
7945/7965 |
SCCP45.8-3-4SR1S |
IP Phone
7970/7971 |
SCCP70.8-3-4SR1S |
IP Phone
7975 |
SCCP75.8-3-4SR1S |
IP Phone
7985 |
cmterm_7985.4-1-5-0 |
Media Termination
Point WS-X6608 |
M00104000005 |
You can determine the version of Cisco Unified CallManager software that is running on your server by accessing Cisco Unified CallManager Administration and then clicking Details.
The following information displays:
· Cisco Unified CallManager System version
· Cisco Unified CallManager Administration version
· Cisco Unified CallManager Installation ID
· Database information
You can
find the minimum versions with which Cisco Unified CallManager release 4.1(3) has
been tested and which previous release of Cisco Unified CallManager has upgrade
support by accessing the following URL: http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_device_support_tables_list.html
Note: Be aware that the release of Cisco IP telephony products does not always coincide with Cisco Unified CallManager releases. If a product is not compatible with Cisco Unified CallManager, you must wait until a compatible version of that product becomes available before you can upgrade to this release of Cisco Unified CallManager. For the most current compatibility combinations and defects, refer to the documentation that is distributed with the Cisco IP telephony products.
For optimal performance, be sure that you use the Cisco IP Telephony Locale Installer that is specific to the version of Cisco Unified CallManager that you use. Be aware that all phrases may not display in the desired locale when you upgrade to a different version of Cisco Unified CallManager. Refer to the readme file that is posted with the Cisco IP Telephony Locale Installer software on the following URL for the complete list of supported languages: http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/locinst/index.htm
Each
release of Cisco Unified CallManager may support a different number of locales.
The full suite of Locale Installers that work with each applicable version of
Cisco Unified CallManager can be found on http://www.cisco.com about 8-10 weeks after the
English version becomes available. You can download the Locale Installers for
all languages that are supported with Cisco Unified CallManager from the
following location:
http://www.cisco.com/kobayashi/sw-center/telephony/callmgr/locale-installer.shtml
Note: When using locales, Cisco recommends that you wait until the locale installer that specifically supports the version of Cisco Unified CallManager that you use becomes available before you upgrade your system. Because some incompatibilities may exist between releases, be sure to only use the locale installer that specifically supports your version of Cisco Unified CallManager.
For additional information about Cisco Unified CallManager, refer to the
following documentation:
Release Notes for
Cisco Unified CallManager Release 4.1(3)
Refer to
the following URL for maintenance release notes that are relevant to this
release of Cisco Unified CallManager:
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/4_1/rel_note/index.htm
Cisco Unified CallManager Document Guide
Refer to the following URL for a list of documents that are related to Cisco Unified CallManager release 4.1(3): http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/4_1/index.htm
To access the documentation suite for voice products, navigate to the following URL: http://www.cisco.com/univercd/cc/td/doc/product/voice/
To access
the latest software upgrades and related documentation for
Cisco Unified CallManager, navigate to the following URL and then choose the
applicable version: http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml
For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
You can access the most current Cisco documentation at this URL:
http://www.cisco.com/univercd/home/home.htm
You can access the Cisco website at this URL:
You can access international Cisco websites at this URL:
http://www.cisco.com/public/countries_languages.shtml
Cisco documentation and additional literature are available in a Documentation DVD package, which may have shipped with your product. The Documentation DVD is updated regularly and may be more current than printed documentation. The Documentation DVD package is available as a single unit.
Registered Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD (product number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.
http://www.cisco.com/en/US/partner/ordering/
http://www.cisco.com/go/marketplace/
You can find instructions for ordering documentation at this URL:
http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm
You can order Cisco documentation in these ways:
o Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/index.shtml
Obtaining Additional
Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources.
· Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.com/go/marketplace/
· Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com/
· Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/packet
· iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine
· Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj
· World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html
You can send comments about technical documentation to bug-doc@cisco.com.
You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn:
Customer Document Ordering
We appreciate your comments.
Cisco provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html
From this site, you can perform these tasks:
· Report security vulnerabilities in Cisco products.
· Obtain assistance with security incidents that involve Cisco products.
· Register to receive security information from Cisco.
A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt
If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:
http://www.cisco.com/en/US/products/products_psirt_rss_feed.html
Reporting Security Problems in Cisco Products
Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT:
· Emergencies security-alert@cisco.com
· Nonemergencies psirt@cisco.com
We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive information that you send to Cisco. PSIRT can work from encrypted information that is compatible with PGP versions 2.x through 8.x. Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one that has the most recent creation date in this public key server list:
http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on
In an emergency, you can also reach PSIRT by telephone:
· 1 877 228-7302
· 1 408 525-6532
For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.
Cisco Technical
Support Website
The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL:
http://www.cisco.com/techsupport
Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL: http://tools.cisco.com/RPF/register/register.do
Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of
Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.
Severity 1 (S1) Your network is down, or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2) Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3) Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.
Severity 4 (S4) You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
CCVP, the Cisco logo, and
Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing
the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems,
Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP,
CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco
Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco
Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step,
Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS,
iPhone, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick
Study, LightStream, Linksys, MeetingPlace, MGX, Networkers, Networking Academy,
Network Registrar, PIX, ProConnect, ScriptShare, SMARTnet, StackWise, The
Fastest Way to Increase Your Internet Quotient, and TransPath are registered
trademarks of Cisco Systems, Inc. and/or its affiliates in the United States
and certain other countries.
All other
trademarks mentioned in this document or Website are
the property of their respective owners. The use of the word partner does not
imply a partnership relationship between Cisco and any other company. (0711R)
Any
Internet Protocol (IP) addresses used in this document are not intended to be
actual addresses. Any examples, command display output, and figures included in
the document are shown for illustrative purposes only. Any use of actual IP
addresses in illustrative content is unintentional and coincidental.
© 2008
Cisco Systems, Inc. All rights reserved.