| >set systemname HQ | Sets the system name of the main router. This system name "HQ" will have to match the user profile in the remote site router for authentication purposes. The system name is sent to the far end router as the userid during ppp authentication.| HQ>set ppp password client (prompts for pap password) | Sets the pap password that will be sent to the remote router when the remote router challenges the main router.
| Enter Password: happy | Prompted to enter the password/secret. "happy" is entered as the pap password. | ReEnter Password: happy | Prompted to reenter the password/secret to ensure consistency. | HQ>set encapsulation ppp | Sets the encapsulation for the user profile default template to ppp. | HQ>set ppp authentication incoming pap | Sets the ppp authentication for incoming calls to be forced to authenticate via pap. | >cd lan | Changes to the LAN profile. | HQ:LAN>set bridging off | Turns bridging off in the LAN profile. | HQ:LAN>set ip routing on | Turns ip routing on in the LAN profile. | HQ:LAN>set ip 198.52.110.254 | Assigns the ip address to the LAN Profile in the network of the Ethernet segment to which the router is attached.
| HQ:LAN>set subnet 255.255.255.0 | Sets the ip netmask of the LAN profile. | HQ>set user remote | Creates the user profile "remote". Changes to the user profile "remote". This user profile name has to match the system name of the remote site router. The system name is received from the far end as the userid during ppp authentication.
| HQ:remote>set bridging off | Turns bridging off in the user profile "remote". | HQ:remote>set ip routing on | Turns ip routing on in the user profile "remote".
| HQ:remote>set ip route destination 198.52.211.0/24 gateway 198.52.110.2 | Sets static ip route that sends any packets destined for the remote ethernet network to the ip address of the user profile "HQ" on the remote site router. | HQ:remote>set ip 198.51.110.3 | Assigns the ip address the user profile "remote" in the same network as the remote router's user profile "HQ".
| HQ:remote>set ip netmask 255.255.255.0 | Sets the ip netmask of the user profile "remote". | HQ:remote>set ip framing none | Sets the ip framing to ipcp. This is necessary because it is required to negotiate ipcp for routing ip using ppp.
| HQ:remote>set timeout 120 | Sets the idle timeout parameter to 120 seconds. If there is no interesting traffic to be forwarded across the ISDN connection for 120 seconds then the call will be disconnected.
| HQ:remote>set 1 number 14085224567 | HQ:remote>set 2 number 14085224567
| Sets the phone numbers in the user profile "remote" that are used to dial out to the remote router. In this case, the remote router has the same phone number for both b channels, so the same number is set in link 1 and link 2. Link 2 is for bandwidth on demand. It will not automatically connect if link 1 isn't already connected. Link 2's number is NOT used for a secondary dial number, it is for bandwidth on demand only. | HQ:remote>set ppp password host (promts for pap password) | Sets the pap secret that the main router is expecting the remote router to send when the main router challenges the remote router to authenticate. | Enter Password: doc | Prompted to enter password/secret. "doc" is enter as the pap password. | ReEnter Password: doc | Prompted to reenter password/secret. | HQ:remote>set ppp authentication outgoing pap
| Sets the ppp authentication on outbound calls to pap. This setting will force bi-directional authentication via pap on the outgoing call basis. When the main router calls the remote router, the main router will force the remote router to authenticate with it via pap.
| |
|---|
| >set systemname remote | Sets the system name of the remote router. This system name "remote" will have to match the user profile in the main site router for authentication purposes. The system name is sent to the far end router as the userid in ppp authentication.
| remote>set ppp password client (prompts for pap password) | Sets the pap password that will be sent to the main router when the main router challenges the remote router. | Enter Password: doc | Prompted to enter the password/secret. "doc" is entered as the pap password. | ReEnter Password: doc | Prompted to reenter password/secret.
| remote>set encapsulation ppp
| Sets the encapsulation for the user profile default template to ppp. | remote>set ppp authentication incoming pap
| Sets the ppp authentication for incoming calls to be forced to authenticate via pap. | remote>cd lan | Changes to the LAN profile. | remote:LAN>set bridging off | Turns bridging off in the LAN profile.
| remote:LAN>set ip routing on | Turns ip routing on in the LAN profile.
| remote:LAN>set ip 198.52.211.254
| Assigns the ip address to the LAN Profile in the network of the Ethernet segment to which the router is attached. | remote:LAN>set subnet 255.255.255.0 | Sets the ip netmask for the LAN profile.
| remote>set user HQ | Creates the user profile "HQ". Changes to the user profile "HQ". This user profile name has to match the system name of the main site router. The system name is received from the far end as the userid during ppp authentication.
| remote:HQ>set bridging off
| Turns bridging off in the user profile "HQ". | remote:HQ>set ip routing on
| Turns ip routing on in the user profile "HQ" | remote:HQ>set ip route destination 198.52.110.0/24 gateway 198.51.110.3
| Sets static ip route that sends any packets destined for the main ethernet network to the ip address of the user profile "remote" on the main site router.
| remote:HQ>set ip 198.51.110.2
| Assigns the ip address to the user profile "HQ". Must be in the same network as the main site router's user profile "remote".
| remote:HQ>set ip netmask 255.255.255.0 | Sets the ip netmask of the user profile "HQ". | remote:HQ>set ip framing none | Sets the ip framing to ipcp. This is necessary because it is required to negotiate ipcp for routing ip using ppp.
| remote:HQ>set timeout 120 | Sets the idle timeout parameter to 120 seconds. If there is no interesting traffic to be forwarded across the ISDN connection for 120 seconds then the call will be disconnected.
| remote:HQ>set 1 number 14085221234 | remote:HQ>set 2 number 14085221234 | Sets the phone numbers in the user profile "HQ" that are used to dial out to the main router. In this case, the main router has the same phone number for both b channels, so the same number is set in link 1 and link 2. Link 2 is for bandwidth on demand. It will not automatically connect if link 1 isn't already connected. Link 2's number is NOT used for a secondary dial number, it is for bandwidth on demand only.
| remote:HQ>set ppp password host (promts for pap password)
| Sets the pap password that will sent to the remote router when the remote router challenges the main router. | Enter Password: happy | Prompted to enter the password/secret. "happy" is entered as the pap password. | ReEnter Password: happy | Prompted to reenter the password/secret to ensure consistency. | remote:HQ>set ppp authentication outgoing pap | Sets the ppp authentication on outbound calls to pap. This setting will force bi-directional authentication via chap on the outgoing call basis. When the remote router calls the main router, the remote router will force the main router to authenticate with it via pap.
| |
|---|