Combinet Sample Configurations

---

CPA 75x bridge to IPX router -cpp

Main Site router

>set systemname HQ	Sets the system name of the main router.
HQ>cd lan	Change to LAN profile.
HQ:LAN>set bridging off	Turns bridging off in the LAN profile.
HQ:LAN>set ipx routing on	Turns ipx routing on
HQ:LAN>set ipx framing 802.3	Sets the ipx framing type to 802.3.
HQ:LAN>set ipx rip update periodic	Sends the ipx rip and sap tables out the ethernet port every 60 seconds.
HQ:LAN>set user remote	Creates the user profile "remote". Changes to the user profile "remote".
HQ:remote>set profile id 0040f902cbb3	Configures the physical ethernet address of the remote
HQ:remote>set bridging off	Turns bridging off in the user profile "remote".
HQ:remote>set timeout 120	Sets the idle timeout parameter to 120 seconds. If there is no interesting traffic to be forwarded across the ISDN connection for 120 seconds then the call will be disconnected. Because the ipx rip updates are periodic by default on the user profile, the call will never disconnect. There are no ipx filters available at this time.
HQ:remote>set ipx routing on	Turns ipx routing on in the user profile "remote".
HQ:remote>set ipx framing 802.3	Sets ipx framing type to 802.3.
HQ:remote>set ipx network AFAF	Sets the ipx network number of the user profile "remote". Note: The far end router will be in the same ipx network as this interface.
HQ:remote>set ipx spoofing 60 (in minutes)	Sets the ipx watchdog spoofing to 60 minutes. If the call disconnects, the users' logins will be spoofed to the main site servers for 60 minutes. If the connection is not made before the 60 minutes, then the spoofing will end and the router will no longer answer the server's watchdog packets. At this point the user's session will be closed.

---

Remote Site router

>set systemname remote	Sets the system name of the remote router.
remote>set user HQ	Creates the user profile "HQ". Changes to the user profile "HQ".
remote:HQ>set profile id 0040f902cbb4	Configures the physical ethernet address of the main router, 0040f902cbb4, in the user profile "HQ". During a cpp call the ethernet address is passed in band during call negotiation, the profile id must match the far end router's ethernet address for the call to be assigned to the proper profile. If the call is not identified, either the profile id is incorrect or missing, then the call will be given to the STANDARD profile instead of the created profile. This event will cause problems in routed environments.
remote:HQ>set bridging on	Turns bridging on in the user profile "HQ"
remote:HQ>set timeout 120	Sets the idle timeout parameter to 120 seconds. If there is no interesting traffic to be forwarded across the ISDN connection for 120 seconds then the call will be disconnected. Because the ipx rip updates are periodic by default on the user profile, the call will never disconnect. There are no ipx filters available at this time.
remote:HQ>set 1 number 14085221234	Sets the phone numbers in the user profile "HQ" that are used to dial out to the main router. In this case, the main router has the same phone number for both b channels, so the same number is set in link 1 and link 2. Link 2 is for bandwidth on demand. It will not automatically connect if link 1 isn't already connected. Link 2's number is NOT used for a secondary dial number, it is for bandwidth on demand only
remote:HQ>set 2 number 14085221234	Note: In this scenario, the main router is not dialling out to the remote router. If it is necessary for the main router to call out to the remote router, then "set 1 number" and "set 2 number" need to be set in the user profile "remote" with the phone numbers for the remote router.