Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
IPsec tunnel using private ip
by Vishal6 -
SIG Policy unexpected behavior
by jjpark -
Error opening tftp server
by mohamadrezaporhosein613 -
!! How do I get a human at American 𝓐𝓲𝓻 immediately?{ SAM }
by sharry786 -
Config GNS3 VM inside a Win10 Virtual machine
by hasitha atapattu -
packet loss seen from L3 switch but not from widows machine
by hmc2500 -
VLANS DHCP
by sergiodagraca730 -
How can I permanently stop Webex loading on startup on my PC?
by info56
Community Activity
!! How do I get a human at American 𝓐𝓲𝓻 immediately?{ SAM }
ℌ픬픴 픠픞픫 ℑ 픰픭픢픞픨 픱픬 픞 American 픯픢픭픯픢픰픢픫픱픞픱픦픳픢 픣픞픰픱? 픖픭픢픞픨 픱픬 American 퓐퓲퓻 픖픢픯픳픦픠픢 픣픬픯 픩픦픳픢 픰픲픭픭픬픯픱, 픜픬픲 픠픞픫 픠픞픩픩 픱픥픢픦픯 American 퓐퓲퓻 픰픢픯픳픦픠픢 24/7 ℌ픬픱픩픦픫픢 퓝퓾퓶퓫퓮퓻 픘픖프:-픒픗프)+1-877-738-0609 픬픯 1-877 American™ (738-0609) (풬퓊풾풸퓀 풸ℴ퓃퓃ℯ풸퓉), 픢픫픤픞픤픢 픦픫 픞 픩픦픳픢 픠픥...
Resolved! FTD Routing question
Hi to all,i am facing the following problem, please refer also to the png attached (i also have some information on the png attached).An IPsec VPN 2811 router tries to establish an IPSec vpn with an FTD. I have setup this config on the lab and i noti...
Config GNS3 VM inside a Win10 Virtual machine
Hi,I need to create a GNS3 lab for internet access via the router inside a Win10 VM. For that, I used a NAT cloud, and that was okay. However, with NAT, I could not access the router's IP from the hosted laptop. Therefore, I tried to use the cloud. H...
packet loss seen from L3 switch but not from widows machine
Sometimes I see packet loss when pinging from a cisco switch but not from a windows machine connected to the same segment (right behind that L3 switch) pinging the same destination. Any reasons why this could happen? Frin Windows
Mobility traffic ports
[Edited on March 16th to add details]HelloI was a bit confused about the traffic ports used by mobility on WLC AireOS or IOS-XE.Trying a quick review of traffic ports used by mobility :AireOS IRCM other than 8.5 IRCM or 8.8.111 and latersince this do...
ASA <-> Fortigate IPSec VTI Issue
Hello, I am currently testing the IPSec Ikev2 VTI Based (routed-based) interworking of FPR2110 and 3rd party equipment (Fortigate) running ASA OS 9.18(3)56 as shown in the picture above.I understand that in the process of creating a Tunnel interface...
VLANS DHCP
Boa tarde amigos Estou tendo dificuldades para configurar IPs classe C, configurar VLANs e configurar um servidor DHCP. Pode me ajudar?
Laptop can't pair with smart TV both are connected with different SSID
Dear Concern,I'm facing an issue where when I connect my laptop to a smart LED, it doesn't connect via WIFI. My laptop is connected to a different SSID, and the LED is connected to a different SSID, but both can ping each other's because of SVIs conf...
Allowing access through ISR-C1111 to FPR1010
HelloSo I configured my RA configuration on my FPR1010 for access to my LAN 192.168.5.0/24 but was curious how exactly would I allow this on my ISR to let me connect to it? Not exactly sure which Ports would be needed opened
A9K-8HG-FLEX-TR not booting with A9K-RSP880-LT-TR running IOS XR 7.9.3
We are trying to set-up A9K-8HG-FLEX-TR in the ASR-9906 chassis with redundant A9K-RSP880-LT-TR and running IOS XR 7.9.3, but after about 2 hours the module is still in the SW_INACTIVE state. All the lights on the module are amber color, but it does...
How can I permanently stop Webex loading on startup on my PC?
Everytime I update the Webex on my PC it keeps rechecking the box under the Settings > General > Start Webex when my computer starts.Is there a way to stop this happening or do Cisco need to fix this?
Unable to factory reset cisco 9300L switch to default settings.
Hello All,We are unable to reset our switch to the factory settings. Its a new switch out off the box that we configured (attempted to configure) and hosed it up. The factory default password isn't working user ID cisco and PW using the system SN. ...
problem VRRP, LACP Nexus 3048TP LAN1K9
Hi, i have problem of synced betewin my 2 switchs nexus 7.0.3.i7.3I use feature BGP, LACP and VRRP (also VPC etc..)But it's impossible of configure correctly the protocolI have many errors :One : In log :%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 9-1...
Catalyst 9100 Access Points not able to communicate with Cisco Aironet
As of now, we are using WLC and Access Points as per the following make and model:Cisco Aironet 1815i Access PointModel: AIR-AP1815I-D-K9Software Version: 8.10.185.0Now, we have purchased new Catalyst 9100 Access Points:AP Model number: C9105AXI-DAft...
IPsec tunnel using private ip
Hi All, Can we create an ipsec tunnel between umbrella data center and Cisco FTD firewall using private ip ?. In my infrastructure isp is terminated on router and FTD is behind Router.
