The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Yes, 헟퐮퐟퐭퐡퐚퐧퐬퐚 퐀퐢퐫퐥퐢퐧퐞 customer support is available 24/7. Whether you have urgent inquiries or need assistance with your travel plans, you can reach out to their dedicated team at any time by calling +ퟭ(ퟴퟱퟱ)ퟗퟓퟔ-ퟓퟕퟔퟕ (USA) or +ퟭ(ퟴퟱퟱ)ퟗퟓퟔ-ퟓퟕퟔퟕ (USA)}. ...
We are currently evaluating Webex Contact Center as we consider transitioning away from UCCX. In our existing setup, if there are more than three people waiting in the call queue, an email is automatically sent to the supervisors to alert them. I've ...
Hello,Is it possible to retrieve the hostname of the client workstation via syslog messages?I activated syslog DAP, but I do not see the hostname of the workstation.For organizational reasons, I do not want to do it via AAA.Thanks a lot
Cisco Unified CCX AdministrationSystem version: 12.5.1.11001-348 (SU1-ES03)Where does one get access to view the error repot that get generated when you click on "send error report" with the Finesse web page?
the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...
I'm setting up a network (see image) and the issue I'm having is that I can see the redistributed routes in the routing table of R1 and R5, but I can't ping to them. When I try to ping 2.2.20.2 (R2) from R5 it's doesn't work, I can ping from R4. Sa...
SW2(config)#aaa server radius dynamic-authorSW2(config-locsvr-da-radius)#client 192.168.100.210 server-key Test123SW2(config-locsvr-da-radius)#client 192.168.100.220 server-key Test123Those commands means that we set AAA server (ISE1 and ISE2 in this...
Hi folks,Running a Catalyst 9800-40 WLC. 1463 WAP's connected, predominantly C9136I WAP's. 8,817 active clients with 4,796 clients on our SSID using PEAP authentication via ISE on the back end. We are observing clients will frequently disconnect fro...
Can someone please explain to me those commands ? SW2(config-if)#authentication host-mode multi-authSW2(config-if)#authentication port-control auto@dot1x Troubleshoot Dot1x and Radius in IOS and IOS-XE Configure Secure Client NAM for Dot1x Using Wind...
Hello, I want to configure 802.1x authentication on an SSID on a 9800-CL hosted in Azure. I have configured the radius server, server group and method list and set this in the AAA section of the WLAN. In Wireshark I can see Access-Request coming from...
Hello, Please i need someone to clarify what is the difference between the "default-originate" command and "network 0.0.0.0 - ip route 0.0.0.0 0.0.0.0 null0" commands. I see both are serving the same purpose by advertising a default route to a pee...
So if you have 2 transports from the WAN Edge, must it have ECMP to vBond in order for vBond to detect the public and private IP of both transports?Say for example you had an MPLS and Public-Internet TLOC. The Public-Internet TLOC is (unwittingly) re...
Hiiiiiiiii I have some new equipment, WS C4507R+E and i would like to have some diagnostic commands, hardware, software, CPU, even modules and supervisors, just to certify that everything is fine... Can someone helpme with some CLI comands plx?
Hello all,Long story but I had a lab upgrade from 5.2 to 6.0.5(M) fail on older APIC-M2's, and Cisco TAC suggested a fabric rebuild. Since I have newer APIC-M4's, I decided to install 5.3.2b on my APIC-M4's, and rebuild my lab fabric using those. All...