The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi ,I have configured the packetfence according to guide , but when i go to connect the SSID. its directly connect and reach the internet and not redirected toward web auth page.i cant find any logs and anything else to troubleshoot. pls check my con...
Good afternoon everyone.I need help, I'm trying to update my ISR4431/K9 router and I'm failing.The original firmware version installed on this router is: isr4400-universalk9.03.16.04b.S.155-3.S4b-ext.SPA.bin, which is a very old version.My task is to...
I have a couple of switches that are trunked via a LAN cable from another switch. I noticed that these switches sometimes have a hard time to SSH into. I get the error: "Connection timed out". After a while and a few tries I can connect just fine. I ...
How is mDNS done correctly on Catalyst 9800 hardware platforms with IOS-XE 17.9.5. We have to troubleshoot Airprint devices that ware visible with mDNS bridging and not visible with mDNS gateway enabled. Other devices like Airplay are vsibble. From s...
If a router has both MPLS and Internet Color, by default it is understood that the traffic should be distributed between MPLS and Internet, is this correct?Looking at Traffic on the interface from vManage, it appears that only MPLS is being used.Both...
Good morning,My manager is trying to register for access to the SNTC portal but is having issues. I believe I have all relevant information - CCOID, email, contract number, serial number - but who can help us with this?Thank you,Leonard
Hi anyone using radware as loadbalancer for wsa? Do we need to change anything in wsa side? We have given radware LB vip in the proxy settings of users but request is not reaching WSA.anyguide is available for the configurations.
Hi ,I am seeing MPLS TE Tunnel is not coming up in my setup. I am using XRV node running version 7.11.2. I have explained below the config and status.Could anyone please check and comment on this issue ? XRV-A Config: ...
Dear CISCO community,this is probably very rare question, and most likely I'll got negative response, but nothing to lose by asking. I found WS-C2960L-16TS-LL switch forgotten in basement, and it is damaged ( not working at all ) by water/humidity da...
Hello, We have a FMC with a pair of Firepower 2110 in HA. Because the certificate asociated to the VPN SSL trustpoint is about to expire, we need to renew the certificate. We issued the CSR to the client for get the new certificate but the client cha...
Hi, Customer bought Cat8500 with DNA Advantage license but is going to use this router in autonomous mode. Resently, It was apllied a license and here is output: License Usage:License Entitlement Tag Count Status--------------------------------------...
Hola, estoy tratando de configurar SNMP en un Access Point C9115AXI-B, el problema es que en el CLI no puedo ejecutar el comando "configure terminal" y no hay manera, también intenté con el comando "debug capwap console cli" pero hasta el momento no ...
I have an ASR1001-x with a single 10G interface to a switch on the LAN. I cannot pass traffic from the sub interface subnets to AWS network connected on WAN. The Lan interface subnet 192.168.50.0/23 passes traffic correctly. the other two do not. Can...
HiCan someone tell me is the fixed version for the recent Arcane Vunerability FMC/FTD 7.0.6-236 or 7.0.6.2-65 we ar running 7.0.5 currently I dont understand the document.?? Thanks