Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Cisco ECE - PCCE 12.6.2 - O365 Troubleshooting - Special Characters
by browto2009 -
Cisco FTD 2100 capture DHCP packets on Client Nodes subnet, DHCP Relay
by red2play -
Multiple SSIDs connect to different VLANS using AIR-CAP3702I AAP
by siskum -
FMC Availability Monthly report of the FTDs?
by RAFAEL LOPEZ -
Cisco Room Kit Eq Native Teams
by davidking112 -
Does the track 1 command not work in packet tracer?
by jc99j -
CSCwb88029 - Disabled management interface cannot be re-enabled
by quevedo_lopez -
Cisco ACI OSPF Neighbor Failer and INIT state
by 홍경택
Community Activity
FMC Availability Monthly report of the FTDs?
Hello everyone, is it possible to generate a report or something that says how many minutes during the month or last 3 months, a FTD was out? For example, if I go to "Monitor-statistics" I can see the uptime of the device, that is, how long it has b...
Cisco Room Kit Eq Native Teams
When a cisco device like the eq is setup for teams, is it native teams or still using webrtc?
Editing My Phone APPS
I enabled SNR on a users line. Works fine.Customer does not like that other phones show the option under CME Services URL>My Phone APPS> Single Number Reach, even when the phone line is not programmed to allow SNR. Is the SNR option something that ...
is fmc version 7.2.5 compatible with ftd version 7.2.4
I need to upgrade vFMC to 7.2.5 version but at this moment i don't want to upgrade my FTD to new version , my FTDs are at version 7.2.4 , will FMC be ok managing lower version of FTD? Thanks
Does the track 1 command not work in packet tracer?
This is the command i type: r2(config)#Track 1 int g0/0/0 line-protocol and it gives me an invalid input at the track part. is there a different configuration mode I need to be in or is it unsupported? I tried this on both 4000 series routers and a 2...
CSCwb88029 - Disabled management interface cannot be re-enabled
Hi, I found a workaround in a FDM-V. This is a example > configure network management-interface enable eth0 firstboot and FTDonbox, setting internal route at /usr/local/sf/lib/perl/5.24.4/SF/NetworkConf/NetworkSettings.pm line 1198.Configuration upda...
Cisco ISE Repository
Hi TeamNeed help with files uploaded to cisco ise repository. All settings related to FTP and file permission done but yet couldn't access files in the repository. See below error message: XP-ISE-02/admin(config)# repository ftp-repoXP-ISE-02/admin(c...
how to disable port 80 or http on an ata-190 device
ata-190 connect two Analog telephones，and connect an cisco router as cucem platform。
Resolved! Requirements of internal SRV records in internal DNS for a MRA deploy
Hello Dears I hope you are doing well The purpose of this message is to know your interpretation to understand some details about the deployment of a MRA infrastructure, specifically about the records of the internal DNS server SRV's. In the docu...
Ping runs on switch directly but not from a device connected to switch
Hello Cisco community, i've got a weird problem. I have a server "A" connected to Gig2/0/18 as an access port (VLAN28) to my Catalyst C9300 switch. I can ping the device from the switch. The switch has an SVI configured for this vlan 28.I also have m...
Cisco CSR8000 need help configuring RTP routing over established IPSEC
Hello,We are configuring virtual CSR8000 over AWS infrastructure, and have configured IPSec tunnel for voice traffic.Tunnel is configured with Public IP tied to physical interface, and RTP endpoint tied to Loopback interface. With this setup tunnel d...
Cisco ACI OSPF Neighbor Failer and INIT state
I set up OSPF between Cisco ACI N9K-C93180YC-EX switch and C9300-48U switch, but Neighbor state is maintained in INIT and will not be established. I will attach the setting screen as a capture screen. Can you tell me what the problem is? Two Nexus sw...
Resolved! Always On IOSXE Sandbox Password Reset
The standard admin password for "IOS XE on Cat8kv AlwaysOn" (devnetsandboxiosxe.cisco.com) is not working. Can this environment please be reset to defaults?
Can anyone SSH to UCS-FI-6536 Fabric Interconnects
Ive a pair of new UCS-FI-6536s and they are all set up and working fine in IMM but we cannot SSH to them as we did on the old FIs.They are on the same VLAN as the old FIs and there are no firewalls inbetween them.Does anyone know if this is even poss...
Firewpower 3140 - MTU on the Physical and Sub Interface
Hi Guys.We are running Firepower 3140 Appliances. There are 2 * 40Gbps connection. The Physical (ETH2/1) 40Gbps interface has the MTU set as 9000 whilst the Sub Interface (ETH2/1.10) and (ETH2/1.20) has the MTU still at 1500In this scenario,1. Is the...
