Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1937906members
1264870discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

!! ~What is the most effective way to complain to 𝑫𝒆𝒍𝒕𝒂?

ℌ픬픴 픠픞픫 ℑ 픰픭픢픞픨 픱픬 픞 푫풆풍풕풂 픯픢픭픯픢픰픢픫픱픞픱픦픳픢 픣픞픰픱? 픖픭픢픞픨 픱픬 푫풆풍풕풂 퓐퓲퓻 픖픢픯픳픦픠픢 픣픬픯 픩픦픳픢 픰픲픭픭픬픯픱, 픜픬픲 픠픞픫 픠픞픩픩 픱픥픢픦픯 푫풆풍풕풂 퓐퓲퓻 픰픢픯픳픦픠픢 24/7 ℌ픬픱픩픦픫픢 퓝퓾퓶퓫퓮퓻 픘픖프:-픒픗프)+ +ퟭ:: ퟴퟳퟳ :: ퟳퟯퟴ :: ퟬퟲퟬퟵ 픬픯 1-877 푫풆풍풕풂™ (738-0609) (풬퓊풾풸퓀 풸ℴ퓃퓃ℯ풸퓉), 픢픫픤픞픤픢 픦픫 픞 픩픦픳픢 픠픥픞픱...

SD-WAN Validator 20.14 Template issue

Hi, I'm configuring the SD-WAN Control Components 20.14 for a lab. I successfully created and attached a device templates with feature templates for the manager and the controller. I created a vEdge Cloud template for the Validator (vBond). But when ...

dbillon by • Level 1
  • 46 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Routes behind a tunnel-te unlabelled

I have created a tunnel-te from xrv16 to csr3, the tunnel is up and getting Pop label to csr3 that's ok.From xrv16 I have learned the route to xrv17 over the tunnel, but checking the Label it's unlabbled as well.I believe the route from xrv16 to xrv1...

ise stuck in configuration memory testing memory

we have a cisco ISE 3595 and I rebooted it by typing reload in the cli. I finally hooked up a vga connection to a monitor and its just stuck on "configuration memory testing memory", keyboard seems unresponsive. I tried connecting from the I/O in the...

Emergency Responder - Multiple Emergency Numbers

At one of my customers, I am implementing CER for emergency dialing (obviously). I have configured and tested 911 call routing. All call routing for emergency services stays on sight (calls go to the on site security desk) and right now 911 is the ...

SSM Multicast and Unicast not working in same switch

Encoder has just one interface too generate Multicast and Unicast video streamsIf all ports of switch are in same VLAN and SSM is not enabled, Client1 is able to play unicast and Client 2 is able to play multicast but when number of streams increase ...

JITINKALYANI_1-1715333697408.png

nexus 7000 eem not runnig cli commands

Hi, I am tryning to run a python script from a eem to send an email and I notice that I am no capable of running any cli command from the eem.  eem example: event manager applet sendemail event cli match "conf t" action 0.5 cli command "enable" actio...

Does any current switch hardware support IPX routing?

We are replacing old Catalyst 6500 switches in one of our business units. The 6ks supported legacy IPX routing for data recovery operations, which is required in some cases for their work. I have been searching for any current info regarding this fea...

imikem2 by • Level 1
  • 101 Views
  • 5 replies
  • 0 Helpful votes

igmp in ISE DACL syntax check fail

I get a syntax check error when the ISE DACL has permit igmp any 224.0.0.0 15.255.255.255.  The ACL is accepted and works on a switch if statically configured.  However, ISE syntax check gives the below error.  Any suggestions?"permit igmp any 224.0....

tachyon05 by • Level 1
  • 79 Views
  • 5 replies
  • 0 Helpful votes
Load more