Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1937898members
1264853discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

igmp in ISE DACL syntax check fail

I get a syntax check error when the ISE DACL has permit igmp any 224.0.0.0 15.255.255.255.  The ACL is accepted and works on a switch if statically configured.  However, ISE syntax check gives the below error.  Any suggestions?"permit igmp any 224.0....

tachyon05 by • Level 1
  • 48 Views
  • 5 replies
  • 0 Helpful votes

ICMP "Flood" on ASA 5516

Hi Community,i do have an ASA 5516 and can see an active connection from the source adress 10.88.72.11 which is causing several GB of ICMP Traffic to one of our internal IPs.The strange thing is, I cannot find this address either in real-time log or ...

DanTee by • Level 1
  • 21 Views
  • 2 replies
  • 1 Helpful votes

Desk Pro and Room Navigator

Is it possible to connect a Room Navigator to a Desk Pro?  I have an executive that does not like to lean towards the camera to shut it off as they say it looks unprofessional and would like to do this with either a Touch 10( EOL) or Navigator.

Does any current switch hardware support IPX routing?

We are replacing old Catalyst 6500 switches in one of our business units. The 6ks supported legacy IPX routing for data recovery operations, which is required in some cases for their work. I have been searching for any current info regarding this fea...

imikem2 by • Level 1
  • 89 Views
  • 4 replies
  • 0 Helpful votes

AF22 drops in ISR4451 while the link is not congested

Hi I have a problem and I am finding it really hard to get thee right answer from documentations:  The customer has 100Mb link and below are the bandwidth allocation to different classes: 100m port = EF = 17.5m / AF1 = 5.5m / AF2 = 16.5m / AF3 = 22m ...

nexus 7000 eem not runnig cli commands

Hi, I am tryning to run a python script from a eem to send an email and I notice that I am no capable of running any cli command from the eem.  eem example: event manager applet sendemail event cli match "conf t" action 0.5 cli command "enable" actio...

C8300 IOS missing whilst password recovery disabled

So this is a tricky one.   One of my engineers has managed to remove the IOS files from a C8300 while configuring, they made the classic mistake of walking away and then coming back to the work half way through a step. They copied across the new IOS ...

SD-WAN Validator 20.14 Template issue

Hi, I'm configuring the SD-WAN Control Components 20.14 for a lab. I successfully created and attached a device templates with feature templates for the manager and the controller. I created a vEdge Cloud template for the Validator (vBond). But when ...

dbillon by • Level 1
  • 17 Views
  • 1 replies
  • 0 Helpful votes

ESA Cluster query

Hi All, Need to configure an Cluster between Hardware device and Virtual appliance and later will remove the Hardware appliance. Before jumping into configuration i have a some query. 1. Is it sma required after forming an cluster to manage the devic...

Vishal6 by • Level 1
  • 239 Views
  • 12 replies
  • 0 Helpful votes

Microsoft RDP application and Yubikey 5

Hi All,I'm attempting to setup a Yubikey 5 as the authentication method for logging into an RDP session on an AWS site that is protected by the Microsoft RDP application.I have users setup using Duo Mobile and it works fine, but one user doesn't have...

Dan110_0-1715705000066.png
Dan110 by • Level 1
  • 24 Views
  • 0 replies
  • 0 Helpful votes

ASR BGP problem

the router looks fine and show ip bgp is correctR2 can't reach ISP by going to R1 to ISP*******************************************************************************************************R1no license smart enable!!spanning-tree extend system-id!i...

Resolved! Routes behind a tunnel-te unlabelled

I have created a tunnel-te from xrv16 to csr3, the tunnel is up and getting Pop label to csr3 that's ok.From xrv16 I have learned the route to xrv17 over the tunnel, but checking the Label it's unlabbled as well.I believe the route from xrv16 to xrv1...

Load more