The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hello, I create Ikev2 site to site tunnel between two cisco FPR 1140. I have same subnet on both location and i used source and destionation NAT in one site. My user try access over web some aplication and it is work, but when other site try to acc...
Hi We have to configure a RB VPN and am wondering if I add the new VTI Interface to The exsisting outside security group or do I have to create a new security group, the outsdide Security group has the Internet facing Interfaces in it.??Thanks
I just bought a brand new CP-8841-3PCC-K9 IP phone from an online dealer here in Germany.When trying to connect the phone to my router fritzbox 7490 I get a starting picture on the phone asking me to "enter activation code". Just that, not "enter act...
How do I set up a Static default route for a particular vlan on a RV34x series router? I am trying to send all traffic from a particular subnet over the VPN. As of now only traffic destined for the VPN network will go over the VPN but I want ALL traf...
Hi, I recently purchased a new 8861 3pcc K9. It is asking for an activation code. I purchased this phone for my small business and I'm the only user. I can NOT figure out how to find this code or get past this. Thanks in advance for your help.
IntroductionValidated DesignTraffic Flow in Cisco Wireless SD-Access solutionMeraki Wireless Design FundamentalMeraki Device-to-Cloud CommunicationsLab SetupConfigurationValidation Introduction With the evolution of software defined networking (SD...
This is a very strange one, Our SSL inspection suddenly started to fail across our (ASA+SFR) environment. - We deployed SSL inspection about 2 years ago, and had no issues till now. The Symptoms we're seeing are - Under the events: SSL Flow error: ...
Hello Team, I hope you are doing well!I'm trying to implement PBR on Industrial switch IE-3400. I used the how to below, but the result was not ok.https://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie3X00/software/17_3/b_ip_routing_17-3_iot_sw...
I'm looking at the SCIM API and cant get a query to go. Tested with both search and get with same error that comes up saying that the orgID is not found. Tested with my Full Admin token and integration with the identity:people-read scope. Tested fr...
HIIs it possible for me to manage switches thats are not part of our SDA Fabric, they are in a dufferent part of the Network, i would like to manage these via DNAC so I could use DNAC to upgrdae Images etc, if its possible could someone tell me how ...
On servers I've set up recently, I'm getting Out Of Range messages during boot. I get the Dell "BIOS splash screen" for a few seconds, and then it's Out Of Range until partway through Windows showing the spinning wheel. This is causing problems, bec...
If a frame with a tag corresponding to the native VLAN enters the trunk port, will the switch take down that frame and send it on over the trunk link as untagged, or will it send it with a tag corresponding to the native VLAN?How I understand it:(Let...
I have Cisco ASA 5505 firewall on wich I wanted to install pfsense. First problem I had was to small CF(128MB) so I went and bought CF with 8GB of space. I used old computer to install pfsense on this CF, and I then noticed that pfsense is using ZFS ...
Hi,how to manually enable the R flag (R-bit) in ipv6 config, let us say in a cisco csr1000v?I have this documentation:https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6/command/ipv6-cr-book/ipv6-i3.html#wp1103499300but unfortunately I could only ...
Hello, We want to create subdomains in our FMC and add a specific FTD device to each subdomain. I have created two sub domains in the FMC and added one FTD device to each subdomain. It works when I create local users and assign them to a specific su...