Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
Cisco ECE - PCCE 12.6.2 - O365 Troubleshooting - Special Characters
by browto2009 -
Cisco FTD 2100 capture DHCP packets on Client Nodes subnet, DHCP Relay
by red2play -
Multiple SSIDs connect to different VLANS using AIR-CAP3702I AAP
by siskum -
The issues of data and voice vlan being the same.
by glaahmet0 -
VRF Aware DHCP on IOS-XR - VRF crossing to Defualt VRF
by ehaparna -
Odd stacking question
by tondaycasse -
How to disable web UI of ata 190
by luoketiantiantian -
Revolucione su interacción con TAC usando RADKit
by Cisco Moderador
Community Activity
How to setting Cisco Estreamer Severity Log?
My name is Zake and i want to ask how to setting severity in Cisco Estream, i use Cisco Firepower 3120 and want ingest log to Azure Sentinel. I was successfull to ingest log but there is too much log i got, when i see there is too much information se...
Login authentication error via CLI on WLC 9800
Hi All, I'm having a weird issue where I cannot access via CLI on the WLC 9800 using radius authentication user, while I can do so with the same user via GUI. I configured AAA servers and groups to match correctly and activated the HTTP and VTY acc...
The issues of data and voice vlan being the same.
The user computer switches to voice vlan but the port configuration has both access vlan and voice vlan.Avaya ip phone switches to voice vlan.The user computer also switches to voice vlan.What could be the cause of this problem?Port configuration swi...
Cisco 9800 Foreign and Cisco 5520 Anchor CWA Guest SSID
I'm trying to configure a guest SSID on the Cisco 9800 with a 5520 as the anchor controller. The SSID has a CWA portal hosted on the external ISE appliance. Normally the flow (which is still working on the existing 5520 foreign controllers) is that y...
Odd stacking question
I recently started working at a new place and I am trying to understand the network config.There are 2 48 port 9300 switches in place, running the latest firmware.They are running a single 1gb trunk port between the switches, but when I dig into the ...
Cisco SX350 show entire command output by default
Hey guys,I have an old SX350 running version 2.5.0.83.Currently when i'm trying to output a command like show running-config I get prompted to show more of the command as it doesn't show all at once.I am able to use the terminal datadump command to s...
how to disable port 80 or http on an ata-190 device
ata-190 connect two Analog telephones，and connect an cisco router as cucem platform。
How to disable web UI of ata 190
On the web UI of ata 190,Administration page only have Reboot button,how can i manage or disable web page?hardware version:1.1.1Software Version: 1.2.2(003_SR2-1)
Cisco UC Automated Phone/Voicemail Setup Based on LDAP Sync
I'm not sure if this is possible or not, but I'm building a new CUCM/Unity (14.X) deployment and am trying to automate it for the following workflow:Extension assigned to a user's ipPhone attribute in Active Directory.User with extension in LDAP sync...
VRF Aware DHCP on IOS-XR - VRF crossing to Defualt VRF
Hi All, I am trying to reconstruct what was covered in a in-space blog doing VRF crossing for IPv4 L3VPN.That means that the client is in it's own VRF and the server is vrf default (global). I want to implement this without using leakage and istaead...
Cisco FPR1140 ikev2 site to site tunnel-FTP application dont work
Hello, I create Ikev2 site to site tunnel between two cisco FPR 1140. I have same subnet on both location and i used source and destionation NAT in one site. My user try access over web some aplication and it is work, but when other site try to acc...
IKEv2 SA drops immediately
Hello,I want to set up a IPSec IKEv2 VPN to a central ASA. On my side we have a cisco 897.First I tried a crypto map configuration. Didn't work because the IKEv2 SA goes UP and immediately goes DOWN with the error message "IKEv2:(SESSION ID = 1,SA ID...
Cisco Room Kit Eq Native Teams
When a cisco device like the eq is setup for teams, is it native teams or still using webrtc?
UCCX 12.5 store data in XML document
I have a list of customer numbers with are associated to agents. There is 10 agents and about 12000 numbers. Each number is associated to one of that 10 agents. My case is to check incoming number and route it to an agent. I have no option to store ...
Webex bot connection with websocket
Hi, I have been connecting with webex bot using webhook and ngrok,but I got a mail stating that you cannot use ngrok since it is a matter of security threat.Is there any alternative for this? Also I tried with websocket as well but I was getting conn...
