The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
We have just installed an ASR1001-x router and need to suport 3 vlans at present is there any information/documentation on how to do this At present we have three sub-interfaces on Physical Port G0/0/3 - namely 0/0/3.3, 0/0/3.4 and 0/0/3.5how do i c...
Hello Guys,Good Day !!Need your help and guidance on cli commands to configure the NAT for the Internet Link on cisco cEdge for the direct L3 TLOC extension (Private IP address) between the 2 cEdges.In vEdge we can simply config NAT enable under the ...
Hello, I know very little about configuring cisco hardware and need some help..... we are currently running an 1800 router and I obtained a new to me 1921 router and would like to replace the 1800 router with the newer one, I managed to get it factor...
Hello,I need your help - currently we have a 2921 Cisco router connected to dual ISPs using "gi0/0 & gi0/1" and we are able to connect to either ISP successfully. Once we connect gi0/2 to any device the connected switch is not able to access the in...
IntroductionProblem DescriptionProcedureNote IntroductionThis document covers the Procedure for Dumping CUCM Fresh Install Logs - Virtualization Problem DescriptionIn order to dump install logs on a virtual UC installation, it is necessary to use a ...
Hello i'm working at a company which is a gold partner with cisco. and I want to recomend Cisco LoA to our customer, however I still don't understand the advantage for the custoemr side. could you please let me know?
Hello,I work on GE in Brazil and we have a MX800 on a room. I was able to share the screen on it, to see myself on cameras, but I couldn't share the video recorded on camera on a Teams Meeting. Can someone support me on how to do this?
My network endpoints use the IP addressed vlans on my core cisco layer three core switch as their gateway addresses. i.e.- vlan 11 endpoint address 192.168.11.3/24 with gateway 192.168.11.1/24 (vlan ip on core) and vlan 12 endpoint address 192.168.12...
CUCM 12.5, I have a Line Group with 3 users, top down then hunt pilot to VM. The RNA Reversion Timeout is set to 15 (per Cisco). One of my users (the first in the line group) sent me a message saying that incoming calls ring to her phone about 10 t...
Hey y'all!I am trying find which port channel member a 2nd switch interface uses? is there a short cut or command that I use for this?Thank you in advance for your help!Inti
I have an EVE-NG lab that consists of a Panorama, 1 FW, and 4 ISE nodes (see lab.jpg attached). The Lab ISE nodes are running 3.2 patch 5 and panorama and Firewall is running 10.2.7-h3. In reading the 3.2 and 3.1 admin guides they both state in the...
Where does one set the FROM e mail address used by CUIC report scheduler to e mail reports? I thought I knew....but it isn't where I thought it was. And I cannot find it in any documentation....
Anyone know if it is possible for a flex AP to cach wired mDNS that has been centrally learned on the WLC? Or does this only work when the AP is in local mode?
a. I initiate a WebEx call on my phone (through WebEx App). Audio is working fine. I then plug in the USBc cable into my phone, CarPlay comes up on the car display. I see the call UI on the car display, but no audiob. I initiate a WebEx call from ...
On my Cisco 2960CG running 15.2(2)E10 when I run command show ip igmp snooping detail, among other things I see that IGMPv3 snooping (minimal) is enabled. Why is this feature called minimal? What is missing from normal v3? Is there any official Cisco...