Document ID: 10458
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configure
Network Diagram
Configurations
Verify
Verify 5500-asp-e
Verify 5500-asp-f
Verify 8540 MSR
Troubleshoot
Related Information
Introduction
Note: Hierarchical virtual path (VP) tunnels are supported since version 12.0 in ATM Switch Processor (ASP) (Cisco Lightstream 1010) or 8540 Multiservice Switch Router (MSR) software. Please note that on the Cisco Lightstream LS1010, the Per-Flow Queuing Feature Card (FC-PFQ) is needed.
In this configuration, you need to transport circuit emulation service (CES) and LAN emulation (LANE) across the WAN. This example uses shaped hierarchical VP tunnels to ensure compliance with a traffic contract. When you use shaped VP tunnels with traffic parameters identical to what the service provider polices, no cells should be dropped in the service provider ATM network. The VP tunnel must be of the constant bit rate (CBR) service category in order to be shaped. It is the only shaped tunnel that the Lightstream 1010 and 8540 MSR currently support. Because this configuration uses hierarchical VP tunnels, virtual circuits (VCs) of multiple service categories can pass through the same hierarchical tunnel at the same time. Unlike shaped tunnels, hierarchical VP tunnels allow both LANE unspecified bit rate (UBR) switched virtual circuits (SVCs) and CES constant bit rate (CBR) permanent virtual circuits (PVCs) to pass through the same tunnel. Therefore, only one CBR VP needs to be purchased from the service provider.
In this example, it is assumed that the purchased CBR VP has a peak cell rate (PCR) of 10 Mbps and a cell delay variation tolerance (CDVT) of 500 cells. Before hierarchical VP tunnels are configured, hierarchical scheduling needs to be enabled with the atm hierarchical-tunnel command. After it is enabled, you must reload the switch for hierarchical scheduling to take effect. Hierarchical VP tunnels cannot coexist on the same physical interface with other types of connections (such as PVCs, SVCs, or unshaped or shaped tunnels). Refer to the documentation for more details. You must remove the configuration of the hierarchical VP tunnel before online removal of the card on whose port hierarchical tunnel is configured.
Please refer to the hardware documentation for limitations on the port numbers that can be used.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
This document is not restricted to specific software and hardware versions.
Conventions
For more information on document conventions, refer to Cisco Technical Tips Conventions.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
Network Diagram
This document uses this network setup:
-
Device 5500-asp-f is VP switching. This function is typically performed by the service provider.
-
LANE services are defined on 8540 MSR. LAN Emulation Clients (LECs) are on 8540 MSR and 5500-asp-e. Note that LANE services are placed on the ATM switch in this example for simplicity. However, that is not the optimal location for LANE services.
-
The two private branch exchanges (PBXs) in the diagram use a CES CBR circuit. Refer to the PBX documentation for more information.
Configurations
This document uses these configurations:
|
5500-asp-e |
|---|
Current configuration: ! version 12.0 no service pad service timestamps debug datetime msec service timestamps log uptime no service password-encryption ! hostname 5500-asp-e ! boot system flash slot0:ls1010-wp-mz.120-3c.W5.9.bin logging buffered 16000 debugging ! ip subnet-zero ip host-routing ! atm hierarchical-tunnel atm connection-traffic-table-row index 63997 vbr-nrt pcr 20480 scr10 9000 mbs 100 atm connection-traffic-table-row index 64000 cbr pcr 10240 cdvt 500 atm lecs-address-default 47.0091.8100.0000.0090.2144.8401.0090.2144.8405.00 1 atm address 47.0091.8100.0000.0050.537e.1401.0050.537e.1401.00 atm router pnni no aesa embedded-number left-justified node 1 level 56 lowest redistribute atm-static ! ! ! interface CBR10/0/0 no ip address no ip directed-broadcast ces circuit 0 circuit-name test ces pvc 0 interface atm11/0/1.6 vpi 6 vci 100 ! interface atm11/0/1 no ip address no ip directed-broadcast no atm ilmi-keepalive atm pvp 6 hierarchical rx-cttr 64000 tx-cttr 64000 ! interface atm11/0/1.6 point-to-point no ip directed-broadcast no atm ilmi-keepalive ! interface atm13/0/0 no ip address no ip directed-broadcast atm maxvp-number 0 ! interface atm13/0/0.1 multipoint ip address 100.100.100.2 255.255.255.0 no ip directed-broadcast lane client ethernet test no cdp enable ! interface Ethernet13/0/0 no ip directed-broadcast ! no ip classless ! line con 0 transport input none line aux 0 line vty 0 4 login ! end |
|
5500-asp-f |
|---|
!--- This switch is configured for VP switching. 5500-asp-f#show run Building configuration... Current configuration: ! version 11.3 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 5500-asp-f ! ! ! atm connection-traffic-table-row index 64000 cbr pcr 10240 cdvt 500 atm address 47.0091.8100.0000.0050.5308.2401.0050.5308.2401.00 atm router pnni no aesa embedded-number left-justified node 1 level 56 lowest redistribute atm-static ! ! ! interface atm11/0/0 no ip address ! interface atm11/0/1 no ip address atm pvp 6 rx-cttr 64000 tx-cttr 64000 interface ATM11/0/0 6 ! interface atm13/0/0 no ip address atm maxvp-number 0 ! interface Ethernet13/0/0 no ip address ! ip classless ! ! line con 0 line aux 0 line vty 0 4 login ! end |
|
8540 MSR |
|---|
8540-MSR#show run Building configuration... Current configuration: ! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 8540-MSR ! logging buffered 4096 debugging ! redundancy main-cpu sync config startup sync config running facility-alarm core-temperature major 53 facility-alarm core-temperature minor 45 ip subnet-zero ! atm hierarchical-tunnel atm connection-traffic-table-row index 63999 cbr pcr 10240 cdvt 500 atm lecs-address-default 47.0091.8100.0000.0090.2144.8401.0090.2144.8405.00 1 atm address 47.0091.8100.0000.0090.2144.8401.0090.2144.8401.00 atm router pnni no aesa embedded-number left-justified node 1 level 56 lowest redistribute atm-static ! ! lane database PVP name test server-atm-address 47.009181000000009021448401.009021448403.01 ! ! interface CBR1/0/0 no ip address no ip directed-broadcast ces circuit 0 circuit-name test ces pvc 0 interface atm2/1/0.6 vpi 6 vci 100 ! interface CBR1/0/1 no ip address no ip directed-broadcast ! interface CBR1/0/2 no ip address no ip directed-broadcast ! interface CBR1/0/3 no ip address no ip directed-broadcast ! ! interface atm2/1/0 no ip address no ip directed-broadcast atm pvp 6 hierarchical rx-cttr 63999 tx-cttr 63999 ! interface atm2/1/0.6 point-to-point no ip directed-broadcast ! interface atm0 no ip address no ip directed-broadcast atm maxvp-number 0 lane config auto-config-atm-address lane config database PVP ! interface atm0.1 multipoint ip address 100.100.100.1 255.255.255.0 no ip directed-broadcast lane server-bus ethernet test lane client ethernet test ! interface Ethernet0 no ip address no ip directed-broadcast ! ! ip classless ! ! line con 0 transport input none line aux 0 line vty 0 4 login ! end |
Verify
These sections provide information you can use to confirm your configurations are working properly.
Verify 5500-asp-e
Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.
-
show atm resource—Used to verify that hierarchical scheduling is enabled.
5500-asp-e#show atm res Resource configuration: Over-subscription-factor 8 Sustained-cell-rate-margin-factor 1% Abr-mode: relative-rate Hierarchical Scheduling Mode : enabled Service Category to Threshold Group mapping: cbr 1 vbr-rt 2 vbr-nrt 3 abr 4 ubr 5 Threshold Groups: Group Max Max Q Min Q Q thresholds Cell Name cells limit limit Mark Discard count instal instal instal --------------------------------------------------- 1 65535 63 63 25 % 87 % 0 cbr-default-tg 2 65535 127 127 25 % 87 % 0 vbrrt-default-tg 3 65535 511 31 25 % 87 % 0 vbrnrt-default-tg 4 65535 511 31 25 % 87 % 0 abr-default-tg 5 65535 511 31 25 % 87 % 0 ubr-default-tg 6 65535 1023 1023 25 % 87 % 0 well-known-vc-tg -
show atm vp—Used to verify that the hierarchical VP tunnel is configured properly.
5500-asp-e#show atm vp Interface VPI Type X-Interface X-VPI Status atm11/0/1 6 PVP HIE. TUNNEL 5500-asp-e#
-
show atm vc interface atmx/y/z.n—Used to see which VCs were established through the hierarchical VP tunnel.
5500-asp-e#show atm vc intterface atm11/0/1.6 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM11/0/1.6 6 3 PVC ATM13/0/0 0 165 SNAP UP ATM11/0/1.6 6 4 PVC ATM13/0/0 0 166 SNAP UP ATM11/0/1.6 6 5 PVC ATM13/0/0 0 164 QSAAL UP ATM11/0/1.6 6 16 PVC ATM13/0/0 0 163 ILMI UP ATM11/0/1.6 6 18 PVC ATM13/0/0 0 167 PNNI UP ATM11/0/1.6 6 37 SVC ATM13/0/0 0 170 LANE UP ATM11/0/1.6 6 38 SVC ATM13/0/0 0 171 LANE UP ATM11/0/1.6 6 39 SVC ATM13/0/0 0 172 LANE UP ATM11/0/1.6 6 40 SVC ATM13/0/0 0 173 LANE UP ATM11/0/1.6 6 100 PVC ATM-P10/0/3 0 16 UP 5500-asp-e#
-
show atm interface resource atmx/y/z.n—Used to verify the resources allocated by VCs that go through the VP tunnel.
Note: All service categories are listed as supported.
5500-asp-e#show atm interface resource atm11/0/1.6 Resource Management configuration: Service Classes: Service Category map: c1 cbr, c1 vbr-rt, c2 vbr-nrt, c3 abr, c4 ubr Scheduling: WRR c1, WRR c2, WRR c3, WRR c4 WRR Weight: 8 c1, 1 c2, 1 c3, 1 c4 Service Categories supported: cbr,vbr-rt,vbr-nrt,abr,ubr Link Distance: 0 kilometers Best effort connection limit: disabled 0 max connections Max traffic parameters by service (rate in Kbps, tolerance in cell-times): Peak-cell-rate RX: none cbr, none vbr, none abr, none ubr Peak-cell-rate TX: none cbr, none vbr, none abr, none ubr Sustained-cell-rate: none vbr RX, none vbr TX Minimum-cell-rate RX: none abr, none ubr Minimum-cell-rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TX Resource Management state: Available bit rates (in Kbps): 7986 cbr RX, 7986 cbr TX, 7986 vbr RX, 7986 vbr TX, 7986 abr RX, 7986 abr TX, 7986 ubr RX, 7986 ubr TX Allocated bit rates: 1741 cbr RX, 1741 cbr TX, 0 vbr RX, 0 vbr TX, 0 abr RX, 0 abr TX, 0 ubr RX, 0 ubr TX 5500-asp-e# -
show atm vc interface atmx/y/z.n n m—Used to view details about VCs that go through the hierarchical VP tunnel.
Note: There are now VCs of multiple service categories (UBR and CBR in this example) that pass through the same tunnel. This was not possible without hierarchical tunnels.
5500-asp-e#show atm vc interface atm11/0/1.6 6 100 Interface: ATM11/0/1.6, Type: oc3suni VPI = 6 VCI = 100 Status: UP Time-since-last-status-change: 00:05:44 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: disabled Usage-Parameter-Control (UPC): pass Wrr weight: 2 Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM-P10/0/3, Type: CBR Cross-connect-VPI = 0 Cross-connect-VCI = 16 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Threshold Group: 1, Cells queued: 0 Rx cells: 1413012, Tx cells: 1412906 Tx Clp0:1412906, Tx Clp1: 0 Rx Clp0:1413012, Rx Clp1: 0 Rx Upc Violations:0, Rx cell drops:0 Rx Clp0 q full drops:0, Rx Clp1 qthresh drops:0 Rx connection-traffic-table-index: 63996 Rx service-category: CBR (Constant Bit Rate) Rx pcr-clp01: 1741 Rx scr-clp01: none Rx mcr-clp01: none Rx cdvt: 1024 (from default for interface) Rx mbs: none Tx connection-traffic-table-index: 63996 Tx service-category: CBR (Constant Bit Rate) Tx pcr-clp01: 1741 Tx scr-clp01: none Tx mcr-clp01: none Tx cdvt: none Tx mbs: none 5500-asp-e#show atm vc interface atm11/0/1.6 6 40 Interface: ATM11/0/1.6, Type: oc3suni VPI = 6 VCI = 40 Status: UP Time-since-last-status-change: 00:08:25 Connection-type: SVC Cast-type: point-to-multipoint-root Packet-discard-option: enabled Usage-Parameter-Control (UPC): pass Wrr weight: 2 Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM13/0/0, Type: ATM Swi/Proc Cross-connect-VPI = 0 Cross-connect-VCI = 173 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Encapsulation: AAL5LANE Threshold Group: 5, Cells queued: 0 Rx cells: 56, Tx cells: 0 Tx Clp0:0, Tx Clp1: 0 Rx Clp0:0, Rx Clp1: 56 Rx Upc Violations:0, Rx cell drops:0 Rx pkts:8, Rx pkt drops:0 Rx connection-traffic-table-index: 2147483647 Rx service-category: UBR (Unspecified Bit Rate) Rx pcr-clp01: 7113539 Rx scr-clp01: none Rx mcr-clp01: none Rx cdvt: 1024 (from default for interface) Rx mbs: none Tx connection-traffic-table-index: 2147483645 Tx service-category: UBR (Unspecified Bit Rate) Tx pcr-clp01: 0 Tx scr-clp01: none Tx mcr-clp01: none Tx cdvt: none Tx mbs: none AAL5 statistics: Crc Errors:0, Sar Timeouts:0, OverSizedSDUs:0 BufSzOvfl: Small:0, Medium:0, Big:0, VeryBig:0, Large:0 5500-asp-e#show atm vc interface atm11/0/1.6 6 5 Interface: ATM11/0/1.6, Type: oc3suni VPI = 6 VCI = 5 Status: UP Time-since-last-status-change: 00:09:30 Connection-type: PVC Cast-type: point-to-point Packet-discard-option: enabled Usage-Parameter-Control (UPC): pass Wrr weight: 15 Number of OAM-configured connections: 0 OAM-configuration: disabled OAM-states: Not-applicable Cross-connect-interface: ATM13/0/0, Type: ATM Swi/Proc Cross-connect-VPI = 0 Cross-connect-VCI = 164 Cross-connect-UPC: pass Cross-connect OAM-configuration: disabled Cross-connect OAM-state: Not-applicable Encapsulation: AALQSAAL Threshold Group: 6, Cells queued: 0 Rx cells: 146, Tx cells: 149 Tx Clp0:149, Tx Clp1: 0 Rx Clp0:64, Rx Clp1: 82 Rx Upc Violations:0, Rx cell drops:0 Rx pkts:138, Rx pkt drops:0 Rx connection-traffic-table-index: 2 Rx service-category: CBR (Constant Bit Rate) Rx pcr-clp01: 424 Rx scr-clp01: none Rx mcr-clp01: none Rx cdvt: 1024 (from default for interface) Rx mbs: none Tx connection-traffic-table-index: 2 Tx service-category: CBR (Constant Bit Rate) Tx pcr-clp01: 424 Tx scr-clp01: none Tx mcr-clp01: none Tx cdvt: none Tx mbs: none AAL5 statistics: Crc Errors:0, Sar Timeouts:0, OverSizedSDUs:0 BufSzOvfl: Small:2, Medium:0, Big:0, VeryBig:0, Large:0
-
show lane—Used to verify that LANE is operational.
5500-asp-e#show lane LE Client ATM13/0/0.1 ELAN name: test Admin: up State: operational Client ID: 2 LEC up for 10 minutes 9 seconds ELAN ID: 0 Join Attempt: 25 Known LE Servers: 1 Last Fail Reason: Locally deactivate HW Address: 0050.537e.1402 Type: ethernet Max Frame Size: 1516 ATM Address: 47.0091810000000050537E1401.0050537E1402.01 VCD rxFrames txFrames Type ATM Address 0 0 0 configure 47.009181000000009021448401.009021448405.00 170 1 2 direct 47.009181000000009021448401.009021448403.01 171 1 0 distribute 47.009181000000009021448401.009021448403.01 172 0 0 send 47.009181000000009021448401.009021448404.01 173 10 0 forward 47.009181000000009021448401.009021448404.01
-
show atm pnni neighbor—Used to verify that the Private Network-Network Interface (PNNI) neighbors are established.
5500-asp-e#show atm pnni nei Neighbors For Node (Index 1, Level 56) Neighbor Name: 8540-MSR, Node number: 9 Neighbor Node Id: 56:160:47.009181000000009021448401.009021448401.00 Neighboring Peer State: Full Link Selection For CBR : minimize blocking of future calls Link Selection For VBR-RT : minimize blocking of future calls Link Selection For VBR-NRT: minimize blocking of future calls Link Selection For ABR : balance load Link Selection For UBR : balance load Port Remote Port Id Hello state ATM11/0/1.6 ATM2/1/0.6 2way_in (Flood Port) 5500-asp-e#
Verify 5500-asp-f
Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.
-
show atm vp—Used to verify that VP is in operational use.
5500-asp-f#show atm vp Interface VPI Type X-Interface X-VPI Status ATM11/0/0 6 PVP ATM11/0/1 6 UP ATM11/0/1 6 PVP ATM11/0/0 6 UP 5500-asp-f#
-
show atm interface resource atmx/y/z—Used to view resources reserved by these two VPs on the interface.
5500-asp-f#show atm interface resource atm11/0/1 Resource Management configuration: Service Classes: Service Category map: c1 cbr, c2 vbr-rt, c3 vbr-nrt, c4 abr, c5 ubr Scheduling: RS c1 WRR c2, WRR c3, WRR c4, WRR c5 WRR Weight: 8 c2, 1 c3, 1 c4, 1 c5 Pacing: disabled 0 Kbps rate configured, 0 Kbps rate installed Service Categories supported: cbr,vbr-rt,vbr-nrt,abr,ubr Link Distance: 0 kilometers Controlled Link sharing: Max aggregate guaranteed services: none RX, none TX Max bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Min bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Best effort connection limit: disabled 0 max connections Max traffic parameters by service (rate in Kbps, tolerance in cell-times): Peak-cell-rate RX: none cbr, none vbr, none abr, none ubr Peak-cell-rate TX: none cbr, none vbr, none abr, none ubr Sustained-cell-rate: none vbr RX, none vbr TX Minimum-cell-rate RX: none abr, none ubr Minimum-cell-rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TXResource Management state: Available bit rates (in Kbps): 137503 cbr RX, 137503 cbr TX, 137503 vbr RX, 137503 vbr TX, 137503 abr RX, 137503 abr TX, 137503 ubr RX, 137503 ubr TX Allocated bit rates: 10240 cbr RX, 10240 cbr TX, 0 vbr RX, 0 vbr TX, 0 abr RX, 0 abr TX, 0 ubr RX, 0 ubr TX Best effort connections: 1 pvcs, 0 svcs
Verify 8540 MSR
Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.
-
show atm vp—Used to verify that the hierarchical VP tunnel is configured properly.
8540-MSR#show atm vp Interface VPI Type X-Interface X-VPI Status ATM2/1/0 6 PVP HIE. TUNNEL -
show atm vc interface atmx/y/z.n—Used to see which VCs were established through the hierarchical VP tunnel.
8540-MSR#show atm vc int atm2/1/0.6 Interface VPI VCI Type X-Interface X-VPI X-VCI Encap Status ATM2/1/0.6 6 3 PVC ATM0 0 111 SNAP UP ATM2/1/0.6 6 4 PVC ATM0 0 112 SNAP UP ATM2/1/0.6 6 5 PVC ATM0 0 110 QSAAL UP ATM2/1/0.6 6 16 PVC ATM0 0 109 ILMI UP ATM2/1/0.6 6 18 PVC ATM0 0 113 PNNI UP ATM2/1/0.6 6 37 SVC ATM0 0 170 LANE UP ATM2/1/0.6 6 38 SVC ATM0 0 150 LANE UP ATM2/1/0.6 6 39 SVC ATM0 0 171 LANE UP ATM2/1/0.6 6 40 SVC ATM0 0 154 LANE UP ATM2/1/0.6 6 100 PVC ATM-P1/0/3 0 16 UP
-
show atm interface resource atmx/y/z.n—Used to verify the resources allocated by VCs that go through the VP tunnel.
8540-MSR#show atm interface resource atm2/1/0 Resource Management configuration: Service Classes: Service Category map: c2 cbr, c2 vbr-rt, c3 vbr-nrt, c4 abr, c5 ubr Scheduling: RS c1 WRR c2, WRR c3, WRR c4, WRR c5 WRR Weight: 8 c2, 1 c3, 1 c4, 1 c5 Pacing: disabled 0 Kbps rate configured, 0 Kbps rate installed Service Categories supported: cbr,vbr-rt,vbr-nrt,abr,ubr Link Distance: 0 kilometers Controlled Link sharing: Max aggregate guaranteed services: none RX, none TX Max bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Min bandwidth: none cbr RX, none cbr TX, none vbr RX, none vbr TX, none abr RX, none abr TX, none ubr RX, none ubr TX Best effort connection limit: disabled 0 max connections Max traffic parameters by service (rate in Kbps, tolerance in cell-times): Peak-cell-rate RX: none cbr, none vbr, none abr, none ubr Peak-cell-rate TX: none cbr, none vbr, none abr, none ubr Sustained-cell-rate: none vbr RX, none vbr TX Minimum-cell-rate RX: none abr, none ubr Minimum-cell-rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TX Resource Management state: Available bit rates (in Kbps): 137503 cbr RX, 137503 cbr TX, 137503 vbr RX, 137503 vbr TX, 137503 abr RX, 137503 abr TX, 137503 ubr RX, 137503 ubr TX Allocated bit rates: 10240 cbr RX, 10240 cbr TX, 0 vbr RX, 0 vbr TX, 0 abr RX, 0 abr TX, 0 ubr RX, 0 ubr TX Best effort connections: 0 pvcs, 0 svcs 8540-MSR#show atm interface resource atm2/1/0.6 Resource Management configuration: Service Categories supported: cbr,vbr-rt,vbr-nrt,abr,ubr Link Distance: 0 kilometers Best effort connection limit: disabled 0 max connections Max traffic parameters by service (rate in Kbps, tolerance in cell-times): Peak-cell-rate RX: none cbr, none vbr, none abr, none ubr Peak-cell-rate TX: none cbr, none vbr, none abr, none ubr Sustained-cell-rate: none vbr RX, none vbr TX Minimum-cell-rate RX: none abr, none ubr Minimum-cell-rate TX: none abr, none ubr CDVT RX: none cbr, none vbr, none abr, none ubr CDVT TX: none cbr, none vbr, none abr, none ubr MBS: none vbr RX, none vbr TX Resource Management state: Available bit rates (in Kbps): 7986 cbr RX, 7986 cbr TX, 7986 vbr RX, 7986 vbr TX, 7986 abr RX, 7986 abr TX, 7986 ubr RX, 7986 ubr TX Allocated bit rates: 1741 cbr RX, 1741 cbr TX, 0 vbr RX, 0 vbr TX, 0 abr RX, 0 abr TX, 0 ubr RX, 0 ubr TX
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
| Updated: Nov 15, 2007 | Document ID: 10458 |