Document ID: 12312
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Configurations
Logical View
IOCP
VM/VTAM XCA Major Node
VM/VTAM Switched Major Node
MVS/VTAM XCA Major Node
MVS/VTAM Switched Major Node
MVS/VTAM LUGROUP Major Node
Router Configuration
Verify
Troubleshoot
Related Information
Introduction
This document explains how to configure two hosts with direct physical units (PU) and logical units (LU) configured for printing.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on the software and hardware versions:
-
Virtual Telecommunications Access Method (VTAM) 4.2/4.3
-
VTAM 3.4.1
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, see the Cisco Technical Tips Conventions.
Configurations
In this section, you are presented with the information to configure the features described in this document.
Note: To find additional information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
Logical View
In this configuration, there are two hosts: an Multiple Virtual Storage/(MVS/VTAM) host running VTAM 4.2/4.3, and a Virtual Media/VTAM (VM/VTAM) host running 3.4.1. The VM users want to get a different initial screen than the MVS users.
IOCP
CHPID 0A is used in MVS VTAM
*
CHPID PATH=((0A)),TYPE=BL
CNTLUNIT CUNUMBR=0580,PATH=(0A),UNITADD=((60,16)),UNIT=3088, X
PROTOCOL=S4
IODEVICE ADDRESS=(C60,16),CUNUMBR=(0580),UNIT=CTC
*
CHPID 0E is used in VM VTAM
*
*
CHPID PATH=((0E)),TYPE=BL
CNTLUNIT CUNUMBR=05C0,PATH=(0E),UNITADD=((60,16)),UNIT=3088, X
PROTOCOL=S4
IODEVICE ADDRESS=(C60,16),CUNUMBR=(05C0),UNIT=CTC
VM/VTAM XCA Major Node
XCA37 VBUILD TYPE=XCA
*
Q60 PORT CUADDR=C60, X
MEDIUM=RING, X
ADAPNO=1, X
SAPADDR=04, X
TIMER=60
*
G37C60 GROUP DIAL=YES,ISTATUS=ACTIVE,ANSWER=ON,CALL=INOUT
L37C6000 LINE
C37C6000 PU
L37C6001 LINE
C37C6001 PU
L37C6002 LINE
C37C6002 PU
L37C6003 LINE
C37C6003 PU
L37C6004 LINE
C37C6004 PU
L37C6005 LINE
C37C6005 PU
L37C6006 LINE
C37C6006 PU
L37C6007 LINE
C37C6007 PU
VM/VTAM Switched Major Node
H37CISCO VBUILD TYPE=SWNET
*
C37EA PU ADDR=04, X
IDBLK=05D, X
IDNUM=22222, X
DISCNT=NO, X
DLOGMOD=T3180, X
LOGAPPL=TPX, X
MAXDATA=521, X
MODETAB=MTS3270, X
MAXPATH=1, X
MAXOUT=7, X
PUTYPE=2, X
PASSLIM=7, X
PACING=7, X
USSTAB=USSSNA
* STATOPT='CISCO 7500' *
P37EA0C LU LOCADDR=12,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P37EA0D LU LOCADDR=13,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P37EA0E LU LOCADDR=14,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P37EA0F LU LOCADDR=15,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
Note: No Dynamic Definition of Dependent Logical Unit (DDDLU) is configured on this switched network (SWNET) Major Node. The direct LUs are configured for printing purposes.
MVS/VTAM XCA Major Node
XCA01 VBUILD TYPE=XCA
*
Q60 PORT CUADDR=C60, X
MEDIUM=RING, X
ADAPNO=0, X
SAPADDR=04, X
TIMER=60
*
G01C60 GROUP DIAL=YES,ISTATUS=ACTIVE,ANSWER=ON,CALL=INOUT
L01C6000 LINE
C01C6000 PU
L01C6001 LINE
C01C6001 PU
L01C6002 LINE
C01C6002 PU
L01C6003 LINE
C01C6003 PU
L01C6004 LINE
C01C6004 PU
L01C6005 LINE
C01C6005 PU
L01C6006 LINE
C01C6006 PU
L01C6007 LINE
C01C6007 PU
MVS/VTAM Switched Major Node
H01CISCO VBUILD TYPE=SWNET, X
MAXDLUR=10
*
C01EA PU ADDR=04, X
IDBLK=05D, X
IDNUM=11111, X
DISCNT=NO, X
DLOGMOD=T3180, X
LOGAPPL=TPX, X
LUGROUP=LUG01, X
LUSEED=T01EA##, X
MAXDATA=521, X
MODETAB=MTS3270, X
MAXPATH=1, X
MAXOUT=7, X
PUTYPE=2, X
PASSLIM=7, X
PACING=7, X
USSTAB=USSSNA
* STATOPT='CISCO 7500'
*
P01EA0C LU LOCADDR=12,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA0D LU LOCADDR=13,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA0E LU LOCADDR=14,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA0F LU LOCADDR=15,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA10 LU LOCADDR=16,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA11 LU LOCADDR=17,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA12 LU LOCADDR=18,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA13 LU LOCADDR=19,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA14 LU LOCADDR=20,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
P01EA15 LU LOCADDR=21,LOGAPPL=,USSTAB=USSPRINT,MODETAB=PRTMODE, -
DLOGMOD=SCS,PACING=2,VPACING=2
MVS/VTAM LUGROUP Major Node
LUGRP01 VBUILD TYPE=LUGROUP
LUG01 LUGROUP
@ LU MODETAB=MTS3270, +
DLOGMOD=T3180, +
LOGAPPL=TPXI, +
USSTAB=USSSNA, +
SSCPFM=USS3270
Router Configuration
version 11.0 ! hostname Celebes source-bridge ring-group 2 source-bridge transparent 2 3 1 1 ! ! interface Ethernet1/0 ip address 172.16.0.9 255.255.0.0 secondary ip address 199.88.1.9 255.255.255.0 bridge-group 1 ! interface Channel4/0 ip address 192.168.250.49 255.255.255.240 no keepalive channel-protocol S4 offload 0100 62 192.168.250.50 HOSTTCP CIPTCP TCPIP TCPIP TCPIP API csna 0100 60 ! interface Channel4/1 ip address 192.168.250.65 255.255.255.240 no keepalive channel-protocol S4 offload 0100 62 192.168.250.66 TCPIP CIPTCP TCPIP TCPIP TCPIP API csna 0100 60 ! interface Channel4/2 ip address 192.168.250.81 255.255.255.240 no keepalive lan TokenRing 0 source-bridge 1 1 2 adapter 0 4000.3745.5a5a adapter 1 4000.3745.5b5b tn3270-server idle-time 1800 unbind-action keep pu C01EA 05D11111 192.168.250.82 token-adapter 0 70 lu-seed T01EA## pu C37EA 05D22222 192.168.250.83 token-adapter 1 74 lu-seed T37EA## ! router ospf 109 redistribute connected subnets redistribute static subnets passive-interface Channel4/0 passive-interface Channel4/1 passive-interface Channel4/2 network 172.16.0.0 0.0.255.255 area 0 network 199.88.1.0 0.0.0.255 area 0 default-metric 2 ! ip route 192.168.250.16 255.255.255.240 172.16.0.12 ip route 192.168.250.32 255.255.255.240 172.16.0.12 ! logging buffered 50000 ! bridge 1 protocol ieee !
Verify
This section provides information you can use to confirm your configuration is working properly.
Certain show commands are supported by the Output Interpreter Tool (registered customers only) , which allows you to view an analysis of show command output.
These versions of the show extended channel tn3270-server command can be used to verify and troubleshoot the TN3270 configuration:
-
show extended channel 4/2 tn3270-server—Displays the current server configuration parameters and the status of the PUs.
-
show extended channel 4/2 tn3270-server pu <pu name>—Displays information about the client LUs associated with a specified PU. For example:
show extended channel 4/2 tn3270-server pu C37EA
-
show extended channel 4/2 tn3270-server pu <puname> lu <locaddr>—Displays the status of the LU. For example:
show extended channel 4/2 tn3270-server pu C37EA lu3
-
show extended channel 4/2 tn3270-server pu <puname> lu <locaddr> history—Displays the status of the LU.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
| Updated: Sep 09, 2005 | Document ID: 12312 |