Document ID: 17573
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
Design Notes
Configure
Network Diagram
Configurations
Verify
Troubleshoot
NetPro Discussion Forums - Featured Conversations
Related Information
Introduction
This document provides a sample configuration for multiple downstream physical units (DSPUs) that are connected to an upstream front-end processor (FEP).
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on Communications Manager/2 (CommMgr/2) that is running on OS/2.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
For more information on document conventions, refer to the Cisco Technical Tips Conventions .
Design Notes
-
These configurations use Remote Source-Route Bridging (RSRB). DSPU can be used over Data Link Switching Plus (DLSw+) (recommended) using Virtual Data-Link Control (VDLC). Refer to Configuring DSPU and SNA Service Point Support for more information.
-
DSPU is configured to use dedicated Logical Unit (LU) resources and allow connections from devices with listed Exchange Identifications (XIDs).
-
A Multiple DSPU to Upstream FEP Sniffer Trace was taken between CommMgr/2 and RouterB.
Configure
In this section, you are presented with the information to configure the features described in this document.
Network Diagram
This document uses this network setup:
Configurations
This document uses these configurations:
|
RouterA |
|---|
hostname RouterA source-bridge ring-group 2989 source-bridge remote-peer 2989 tcp 198.92.0.235 source-bridge remote-peer 2989 tcp 192.190.226.148 interface Serial0 ip address 193.100.1.1 255.255.255.0 interface TokenRing0 ip address 198.92.0.235 255.255.255.0 ring-speed 16 source-bridge 2564 1 2989 source-bridge spanning |
|
RouterB |
|---|
hostname RouterB source-bridge ring-group 2989 source-bridge remote-peer 2989 tcp 192.190.226.148 source-bridge remote-peer 2989 tcp 198.92.0.235 dspu rsrb 77 1 2989 4000.ffff.0001 dspu rsrb enable-host lsap 4 dspu host HOST3745 xid-snd 05d05197 rmac 4001.3745.1088 lsap 4 rsap 4 dspu rsrb start HOST3745 dspu pu SRVTOK2 xid-rcv 05daa005 lsap 4 rsap 4 dspu lu 2 4 host HOST3745 5 dspu pu SRVTOK xid-rcv 05d10001 lsap 4 rsap 4 dspu lu 2 4 host HOST3745 8 interface Serial0 ip address 193.100.1.2 255.255.255.0 interface TokenRing0 mac-address 4000.4400.0001 ip address 192.190.226.148 255.255.255.0 no ip route-cache ring-speed 16 dspu enable-pu lsap 4 |
|
CommMgr/2 1 |
|---|
|
Configure CommMgr/2 on the first PC in this manner:
|
|
CommMgr/2 2 |
|---|
|
Configure CommMgr/2 on the second PC in this manner:
|
|
VTAM Switched Major Node |
|---|
SWCERT5A VBUILD TYPE=SWNET,MAXGRP=4,MAXNO=4
*
DSPUA PU ADDR=01,
PUTYPE=2,
IDBLK=05D,
IDNUM=05197,
MODETAB=ALAMODE,
DLOGMOD=SX32702S,
DISCNT=(NO),
USSTAB=USSSNA,
ISTATUS=ACTIVE,
MAXDATA=521,
IRETRY=YES,
MAXOUT=7,
PASSLIM=5,
MAXPATH=4
*
DSPAL00 LU LOCADDR=02
DSPAL01 LU LOCADDR=03
DSPAL02 LU LOCADDR=04
.
.
.
DSPAL20 LU LOCADDR=22
|
Verify
There is currently no verification procedure available for this configuration.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
NetPro Discussion Forums - Featured Conversations
| NetPro Discussion Forums - Featured Conversations for IBM |
| Network Infrastructure: Enterprise Data Centers |
Related Information
| Updated: Sep 09, 2005 | Document ID: 17573 |