Document ID: 12318
Contents
Introduction
Before You Begin
Conventions
Prerequisites
Components Used
Configure
Configurations
HCD Panels
TCP/IP Profile
Router Configuration
Verify
Troubleshoot
Related Information
Introduction
This document provides an example of a complex Channel Interface Processor (CIP) configuration using an Enterprise System Connection (ESCON) director, ESCON Multiple Image Facility (EMIF), and Hardware Configuration Definition (HCD). Not all the HCD screens are included for every CLAW (Common Link Access to Workstation) connection, however, all the screens for one of the connections have been included.
Before You Begin
Conventions
For more information on document conventions, see the Cisco Technical Tips Conventions.
Prerequisites
No specific prerequisites exist for this document.
Components Used
This document is not restricted to specific software and hardware versions.
The information presented in this document was created from devices in a specific lab environment. All the devices used in this document started with a cleared (default) configuration. If you are working in a live network, ensure that you understand the potential impact of any command before using it.
Configure
In this section, you are presented with the information to configure the features described in this document.
Note: In order to find more information on the commands used in this document, use the Command Lookup Tool (registered customers only) .
This document uses the network setup shown below.
-----------------------------------------------------------------------------
| HOST INFORMATION
|
-----------------------------------------------------------------------------
+------------+-+
| A1AA | | +------+
+------------| |34 | | ...
| E1EE | |---------------|D8 | +----+ . .
+------------| | | | |7000| . .
| F1FF | | +--------|E9 EF|--------| |---. TR .-----
+------------+-+ | | | +----+ . .
| +-----|DA | . .
+------------+-+21 | | | | ...
| D1DD | |------+ | +--|DE |
+------------+-+ | | | |
| | +------+
+------------+-+ | |
| S1SS | |31 | | ESCON
+------------| |---------+ | Director
| B1BB | | |
+------------+-+ |
|
+------------+-+20 |
| G1GG | |------------+
+------------+-+
Notes:
-
A1AA, E1EE, and F1FF are on a 9021-952 .
-
D1DD is on a 9672 (#00).
-
S1SS and B1BB are on a 9672 (#02).
-
G1GG is on a 9672 (#04).
All CHPIDs are defined as CNC and SHARED.
Configurations
This document uses the configuration shown below.
|
Configuration 1 |
|---|
MVS Config DYNAMIC=NO
UNIT=3172
Control Unit=3172
TIMEOUT=NO
LPAR CU PATH LINK UNIT UNITADD CUADD IODEVADD CU UNIT UNITADD
---- ---- ---- ---- ---- ------- ----- -------- ---- ---- -------
A1AA 3450 34 EF 3172 50,2 52,2 3450 3172 50
B1BB 3150 31 EF 3172 50,2 58,2 3150 3172 50
D1DD 4F50 21 EF 3172 50,2 50,2 4F50 3172 50
E1EE 3452 34 EF 3172 50,2 5A,2 3452 3172 50
F1FF 3451 34 EF 3172 50,2 54,2 3451 3172 50
G1GG 2051 20 EF 3172 50,2 56,2 2051 3172 50
S1SS 5150 31 EF 3172 50,2 5C,2 5150 3172 50
|
HCD Panels
The HCD information for Configuration 1 is provided below.
The first part shows all the panels used in viewing the HCD definition for the CIP card. The second part shows the panels used for changing a CIP control unit as it shows more information.
The lines beginning with = = = = = = = indicate a change in panels.
========================================================================
CHANNEL PATH LIST ROW 1
SELECT ONE OR MORE CHANNEL PATHS, THEN SELECT AN ACTION.
PROCESSOR ID . . . : S962#1 A1AA D1DD E1EE F1FF
CONFIGURATION MODE : LPAR
DYN + --ENTRY +--
/ CHPID TYPE + MODE + SWITCH SWITCH PORT CON. DESCRIPTION
_ 34 CNC SHR 01 __ __ CISCO
========================================================================
.-------------------- VIEW CHANNEL PATH DEFINITION ----------------
|
|
| PROCESSOR ID . . . : S962#1 A1AA D1DD E1EE F1FF
| CONFIGURATION MODE : LPAR
|
| CHANNEL PATH ID . . . . . . : 34
| CHANNEL PATH TYPE . . . . . : CNC
| OPERATION MODE . . . . . . . : SHR
|
| DESCRIPTION . . . . . . . . : ESCON 3172/CISCO
|
| DYNAMIC SWITCH ID . . . . . : 01
| ENTRY SWITCH ID . . . . . . :
| ENTRY PORT . . . . . . . . . :
|
| ENTER TO CONTINUE.
|
| F1=HELP F2=SPLIT F9=SWAP F12=CANCEL
'------------------------------------------------------------------
========================================================================
.-------------------------- VIEW ACCESS LIST ---------------------------
| ROW 1 OF 3
|
| THE FOLLOWING PARTITIONS ARE IN THE ACCESS LIST.
|
| CHANNEL PATH ID . . : 34 CHANNEL PATH TYPE . . : CNC
| OPERATION MODE . . . : SHR
|
| ENTER TO CONTINUE.
|
| PARTITION NAME NUMBER USAGE DESCRIPTION
| A1AA 1 OS
| E1EE 3 OS
| F1FF 5 OS
| ************************** BOTTOM OF DATA ***************************
|
|
|
|
|
| COMMAND ===> ____________________________________ SCROLL ===> PAGE
| F1=HELP F2=SPLIT F6=PREVIOUS F7=BACKWARD F8=FORWARD
| F9=SWAP F12=CANCEL F22=COMMAND
'-----------------------------------------------------------------------
========================================================================
CONTROL UNIT LIST
SELECT ONE OR MORE CONTROL UNITS, THEN SELECT AN ACTION.
PROCESSOR ID . . . : S962#1 CHANNEL PATH ID . : 34
/ CU TYPE + SERIAL NO. DESCRIPTION
_ 13C0 3172 __________ ESCON 3172
_ 33C0 3172 __________ ESCON 3172
_ 3450 3172 __________ CISCO
_ 3451 3172 __________ CISCO
_ 3452 3172 __________ CISCO
========================================================================
I/O DEVICE LIST ROW 1 OF 2 MOR
SELECT ONE OR MORE DEVICES, THEN SELECT AN ACTION.
CONTROL UNIT NUMBER : 3450 CONTROL UNIT TYPE . : 3172
-------DEVICE------- -------CONTROL UNIT NUMBERS + ---------
/ NUMBER TYPE + OS 1--- 2--- 3--- 4--- 5--- 6--- 7--- 8---
_ 0052 3172 Y 3450 ____ ____ ____ ____ ____ ____ ____
_ 0053 3172 Y 3450 ____ ____ ____ ____ ____ ____ ____
========================================================================
.------------------------- VIEW DEVICE DEFINITION ----------------------
|
|
| DEVICE NUMBER . . . . . . . : 0052
| DEVICE TYPE . . . . . . . . : 3172
|
| SERIAL NUMBER . . . . . . . :
| DESCRIPTION . . . . . . . . : CISCO
|
| CONNECTED TO CUS : 3450
|
| ENTER TO CONTINUE.
|
|
|
| F1=HELP F2=SPLIT F9=SWAP F12=CANCEL
'-----------------------------------------------------------------------
========================================================================
.----------------- VIEW DEVICE / PROCESSOR DEFINITION ------------------
| ROW 1 OF 1
|
| SELECT ONE OR MORE PROCESSORS TO VIEW THE DEVICE CANDIDATE LIST, OR
| ENTER TO CONTINUE WITHOUT SELECTION.
|
| DEVICE NUMBER . : 0052 DEVICE TYPE . : 3172
|
| / PROCESSOR ID UA TIME-OUT STADET PREFERRED EXPLICIT DEVICE
| CHPID CANDIDATE LIST
| _ S962#1 50 NO YES NO
| ************************** BOTTOM OF DATA ***************************
|
|
|
|
|
|
|
|
| COMMAND ===> ____________________________________ SCROLL ===> PAGE
| F1=HELP F2=SPLIT F6=PREVIOUS F7=BACKWARD F8=FORWARD
| F9=SWAP F12=CANCEL F22=COMMAND
'-----------------------------------------------------------------------
========================================================================
.------------- VIEW DEVICE / OS CONFIGURATION DEFINITIONS --------------
| VIEW QUERY HELP
| --------------------------------------------------------------------
| ROW 1 OF 1
|
| SELECT ONE OR MORE OPERATING SYSTEM CONFIGURATIONS, THEN SELECT AN
| ACTION.
|
| DEVICE NUMBER . : 0052 DEVICE TYPE . . : 3172
|
| / CONFIG. ID TYPE DESCRIPTION
| _ MVS MVS SHARED MVS - 24 JAN 93
| ************************** BOTTOM OF DATA ***************************
|
|
|
|
|
|
| COMMAND ===> ____________________________________ SCROLL ===> PAGE
| F1=HELP F2=SPLIT F4=PROMPT F5=RESET F6=PREVIOUS
| F7=BACKWARD F8=FORWARD F9=SWAP F10=ACTIONS F12=CANCEL
| F13=INSTRUCT F22=COMMAND
'-----------------------------------------------------------------------
========================================================================
.-----------------------------------------------------------------------
| VIEW DEVICE PARAMETER / FEATURE DEFINITION ROW 1
|
| CONFIGURATION ID . : MVS SHARED MVS - 24 JAN 93
| DEVICE NUMBER . . : 0052 DEVICE TYPE . . . : 3172
| GENERIC / VM DEVICE TYPE . . . . : 3172
|
| ENTER TO CONTINUE.
|
| PARAMETER/ VALUE REQ. DESCRIPTION
| FEATURE
| OFFLINE NO DEVICE CONSIDERED ONLINE OR OFFLINE AT IPL
| DYNAMIC NO DEVICE HAS BEEN DEFINED TO BE DYNAMIC
| ***************************** BOTTOM OF DATA *************************
|
|
|
|
|
|
| COMMAND ===> __________________________________________ SCROLL ===> PA
| F1=HELP F2=SPLIT F7=BACKWARD F8=FORWARD F9=SWAP
| F12=CANCEL F22=COMMAND
'-----------------------------------------------------------------------
These panels go through the sequence of changing a control unit definition. This panel provides more information than just viewing the definition.
.----------------- CHANGE CONTROL UNIT DEFINITION ------------------. | | | | | SPECIFY OR REVISE THE FOLLOWING VALUES. | | | | CONTROL UNIT NUMBER . . . : 3450 | | | | CONTROL UNIT TYPE . . . . . 3172 + | | | | SERIAL NUMBER . . . . . . . __________ | | DESCRIPTION . . . . . . . . CISCO | | | | CONNECTED TO SWITCHES . . . __ __ __ __ __ __ __ __ + | | PORTS . . . . . . . . . . . __ __ __ __ __ __ __ __ + | | | | | | F1=HELP F2=SPLIT F3=EXIT F4=PROMPT F5=RESET F9=SWAP | | F12=CANCEL | '-------------------------------------------------------------------' ======================================================================== .---------------------- SELECT PROCESSOR / CONTROL UNIT ---------------- | MODIFY VIEW QUERY HELP | ---------------------------------------------------------------------- | ROW 1 OF 5 MORE: | | SELECT ONE OR MORE PROCESSORS, THEN SELECT AN ACTION. | | CONTROL UNIT NUMBER . . : 3450 CONTROL UNIT TYPE . . . : 3172 | | / PROC. ID ATT. LOG. ADDR. ------CHANNEL PATH ID . LINK ADDRESS + ---- | (CUADD) + 1---- 2---- 3---- 4---- 5---- 6---- 7---- 8 | _ S962#1 YES 1 34.EF _____ _____ _____ _____ _____ _____ _ | _ S820#1 _ _____ _____ _____ _____ _____ _____ _____ _ | _ S9672#00 _ _____ _____ _____ _____ _____ _____ _____ _ | _ S9672#02 _ _____ _____ _____ _____ _____ _____ _____ _ | _ S9672#04 _ _____ _____ _____ _____ _____ _____ _____ _ | ***************************** BOTTOM OF DATA ************************* | | COMMAND ===> __________________________________________ SCROLL ===> PA | F1=HELP F2=SPLIT F3=EXIT F4=PROMPT F5=RESET | F6=PREVIOUS F7=BACKWARD F8=FORWARD F9=SWAP F10=ACTION | F12=CANCEL F13=INSTRUCT F20=RIGHT F22=COMMAND '----------------------------------------------------------------------- !--- Previous panel. Scroll right. .---------------------- SELECT PROCESSOR / CONTROL UNIT ---------------- | MODIFY VIEW QUERY HELP | ---------------------------------------------------------------------- | ROW 1 OF 5 MORE: < | | SELECT ONE OR MORE PROCESSORS, THEN SELECT AN ACTION. | | CONTROL UNIT NUMBER . . : 3450 CONTROL UNIT TYPE . . . : 3172 | | / PROC. ID ATT. -------------UNIT ADDRESS . UNIT RANGE + ------------- | 1----- 2----- 3----- 4----- 5----- 6----- 7----- 8---- | _ S962#1 YES 50.002 ______ ______ ______ ______ ______ ______ _____ | _ S820#1 ______ ______ ______ ______ ______ ______ ______ _____ | _ S9672#00 ______ ______ ______ ______ ______ ______ ______ _____ | _ S9672#02 ______ ______ ______ ______ ______ ______ ______ _____ | _ S9672#04 ______ ______ ______ ______ ______ ______ ______ _____ | ***************************** BOTTOM OF DATA ************************* | | COMMAND ===> __________________________________________ SCROLL ===> PA | F1=HELP F2=SPLIT F3=EXIT F4=PROMPT F5=RESET | F6=PREVIOUS F7=BACKWARD F8=FORWARD F9=SWAP F10=ACTION | F12=CANCEL F13=INSTRUCT F19=LEFT F20=RIGHT F22=COMMAN '----------------------------------------------------------------------- !--- Previous panel. Scroll right. .---------------------- SELECT PROCESSOR / CONTROL UNIT ---------------- | MODIFY VIEW QUERY HELP | ---------------------------------------------------------------------- | ROW 1 OF 5 MORE: < | | SELECT ONE OR MORE PROCESSORS, THEN SELECT AN ACTION. | | CONTROL UNIT NUMBER . . : 3450 CONTROL UNIT TYPE . . . : 3172 | | / PROC. ID ATT. PROTOCOL + I/O CONCURRENCY | LEVEL + | _ S962#1 YES S4 2 | _ S820#1 __ _ | _ S9672#00 __ _ | _ S9672#02 __ _ | _ S9672#04 __ _ | ***************************** BOTTOM OF DATA ************************* | | COMMAND ===> __________________________________________ SCROLL ===> PA | F1=HELP F2=SPLIT F3=EXIT F4=PROMPT F5=RESET | F6=PREVIOUS F7=BACKWARD F8=FORWARD F9=SWAP F10=ACTION | F12=CANCEL F13=INSTRUCT F19=LEFT F22=COMMAND '----------------------------------------------------------------------- !--- C entered in S962#1 field on panel above. .-------------------- CHANGE CONTROL UNIT DEFINITION ------------------- | | | SPECIFY OR REVISE THE FOLLOWING VALUES. | | CONTROL UNIT NUMBER . : 3450 TYPE . . . . . . : 3172 | PROCESSOR ID . . . . . : S962#1 A1AA D1DD E1EE F1FF | | CHANNEL PATH IDS . . . . 34 __ __ __ __ __ __ __ + | LINK ADDRESS . . . . . . EF __ __ __ __ __ __ __ + | | UNIT ADDRESS . . . . . . 50 __ __ __ __ __ __ __ + | NUMBER OF UNITS . . . . 002 ___ ___ ___ ___ ___ ___ ___ | | LOGICAL ADDRESS . . . . 1 + (SAME AS CUADD) | | PROTOCOL . . . . . . . . S4 + (D, S OR S4) | I/O CONCURRENCY LEVEL . 2 + (1, 2 OR 3) | | | F1=HELP F2=SPLIT F4=PROMPT F5=RESET F9=SWAP F12=CANCEL '----------------------------------------------------------------------- ****
TCP/IP Profile
These configurations provide the relevant sections of the TCPIP host PROFILE dataset. Two hosts are included in the TCP/IP profiles.
|
S1SS LPAR |
|---|
DEVICE VICRC007DV CLAW 05C BCSCSSG VICRC007 NONE 20 20 4096 4096 LINK VICRC007LK IP 0 VICRC007DV HOME 131.108.160.47 VICRC007LK PRIMARYINTERFACE VICRC007LK GATEWAY ; Network First hop Driver Packet Size Subnet Mask Subnet 131.108 = VICRC007LK 4096 0.0.255.0 0.0.160.0 DEFAULTNET = VICRC007LK 4096 0 START VICRC007DV |
|
E1EE LPAR |
|---|
DEVICE VICRC007DV CLAW 05A BCSC05 VICRC007 NONE 20 20 4096 4096 LINK VICRC007LK IP 0 VICRC007DV HOME 131.108.160.46 VICRC007LK PRIMARYINTERFACE VICRC007LK GATEWAY ; Network First hop Driver Packet Size Subnet Mask Subnet 131.108 = VICRC007LK 4096 0.0.255.0 0.0.160.0 DEFAULTNET = VICRC007LK 4096 0 START VICRC007DV *** |
Router Configuration
CIP definition:
interface Channel4/0 ip address 131.108.160.1 255.255.255.0 no ip redirects ip route-cache same-interface no keepalive claw E920 50 131.108.160.42 BCSC01D VICRC007 TCPIP TCPIP claw D830 50 131.108.160.46 BCSC05 VICRC007 TCPIP TCPIP claw D810 50 131.108.160.41 BCSC01A VICRC007 TCPIP TCPIP claw D850 50 131.108.160.43 BCSC01F VICRC007 TCPIP TCPIP claw DA10 50 131.108.160.45 BCSC01B VICRC007 TCPIP TCPIP claw DA20 50 131.108.160.47 BCSCSSG VICRC007 TCPIP TCPIP claw DE20 50 131.108.160.44 BCSC01G VICRC007 TCPIP TCPIP
Verify
There is currently no verification procedure available for this configuration.
Troubleshoot
There is currently no specific troubleshooting information available for this configuration.
Related Information
| Updated: Sep 09, 2005 | Document ID: 12318 |