Worldwide [change] |Account |Register |About Cisco
Guest

Hierarchical Navigation

Products & Services

Ericsson MD110 BC12 SP5 using E1 ECMA-QSIG to Cisco Unified CallManager 5.0

Downloads

Ericsson MD110 BC12 SP5 using E1 ECMA-QSIG to Cisco Unified CallManager 5.0
Table of Contents

Introduction

  • . This is an application note for connectivity of Ericsson MD-110 Release BC12 PBX with Cisco Unified CallManager Release 5.0 via Cisco 3845 w/ VWIC-2MFT-E1 as MGCP gateway using ECMA QSIG protocol.
  • The network topology diagram (Figure 1) shows the test setup for end-to-end interoperability with the Cisco Unified CallManager connected to the PBX via Cisco3845 w/ VWIC-2MFT-E1 link as MGCP gateway. Connectivity is achieved by using the PRI ECMA-QSIG E1 protocol type on the MGCP gateway with CallManager Service parameter QSIG variant of ECMA and ECMA switch type on the Ericsson MD-110 PBX.
  • This Application Note uses the Cisco3845 w/ VWIC-2MFT-E1 voice gateway, however other Cisco voice gateways are also an option to use since CallManager QSIG implementation does not depend on the physical interface.

Network Topology

Basic Call Setup End-to-End Configuration

Figure 1. Network Topology or Test Setup

Limitations

Calling/Connected Name Restrictions
  • Ericsson phone displayed Calling/Connected Name when CCM sends it as restricted System Components

System Components

Hardware Requirements

Cisco Hardware

· Cisco 3845 w/ VWIC-2MFT-E1
· Cisco Unified CallManager Server

Ericsson MD110 PBX Hardware

· Circuit card TL76/1, PRI-E1

Software Requirements

· Cisco Unified CallManager version: 5.0
· Ericsson MD110 software release: BC12 SP5
· Cisco 3845 IOS release: 12.4

Features

Features Supported
  • CLIP-Calling Line (Number) Identification Presentation

• CLIR-Calling Line (Number) Identification Restriction

• CNIP-Calling Name Identification Presentation

• COLP-Connected Line (Number) Identification Presentation

• COLR- Connected Line (Number) Identification Restriction

• CONP-Connected Name Identification Presentation

• Sending Alerting Name

• CT-Call Transfer (by join)

• CFU-Call Forwarding Unconditional (by join)

• CFB-Call Forwarding Busy (by join)

• CFNR-Call Forwarding No Reply (by join)

Features Not Supported

• Ericsson did not honor CNIR-Calling Name Identification Restriction

• Ericsson did not honor CONR- Connected Name Identification Restriction

• Ericsson did not Update Name and Number for Call Transfer, the limitation resides on the MD110 when using the configuration (ECMA) described in this document.

• Ericsson did not support External/Network Call Forwarding, the limitation resides on the MD110 when using the configuration (ECMA) described in this document.

• Ericsson did not support Call Forwarding by Reroute, the limitation resides on the MD110 when using the configuration (ECMA) described in this document.

• Ericsson did not support Call Completion, the limitation resides on the MD110 when using the configuration (ECMA) described in this document.

• Ericsson did not support ANF-PR-Additional Network Feature Path Replacement, the limitation resides on the MD110 when using the configuration (ECMA) described in this document.

  • Ericsson did not support Standard QSIG-MWI- Message Waiting Indication (lamp ON, lamp OFF), MD110 utilizes a Manufacturer's specific code to activate/deactivate MWI across the QSIG link

Configuration

Configuring the Ericsson MD-110 PBX
Warning: The Ericsson MD-110 PBX user interface is very precise. All parameters and options are mapped to position-dependent numeric fields within the various commands listed below. The user must have the correct revision of the Ericsson MD-110 PBX administration manual to be able to decipher each field position and determine its meaning. It is therefore not advisable to make changes to an MD-110 PBX unless you know exactly what you are doing. A single number out of place in a command string can cause unusual behavior on the PBX.
Configure the Ericsson MD-110 PBX in the following sequence:

• ROCAI Route Category Initiate

• RODAI Route Data Initiate

• ROEQI Route Equipment Initiate

• RODDI Route External Destination

Configuration Menus and Commands
Route Category Initiate

Setup internal characteristics for the route. Ex. Traffic direction, services, Bearer capabilities.

For Ericsson 1 node

<ROCAP:ROU=100;

ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

100 7110000000000010 5 2110030000 0 30 128 03151515 111110000031 111111

END

<ROCAP:ROU=101;

ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

101 7110000000000010 5 2110030000 0 30 128 03151515 111110000031 001100

END

For Ericsson 2 node

<ROCAP:ROU=1;

ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

1 7110000000000010 5 3110000000 0 30 128 03151515 111110000031 111111

END

<ROCAP:ROU=3;

ROUTE CATEGORY DATA

ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP

3 7110000000000010 5 3110000000 0 30 128 03151515 111110000031 111111

END

Route Data Initiate

For Ericsson 1 node

E1-PRI ECMA QSIG Route Protocol Characteristics, protocol side "Network"

<RODAP:ROU=100;

ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

100 SL60 H'00000310 H'15400000 H'06300000 NO

END

PSTN trunk E1-PRI ETSI Route Protocol Characteristics, protocol side "Network"

<RODAP:ROU=100;

ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

100 SL60 H'00000310 H'05400000 H'06300000 NO

END

E1-PRI ECMA QSIG Route Protocol Characteristics, protocol side "User"

<RODAP:ROU=101;

ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

101 SL60 H'00000310 H'15400000 H'06400000 NO

END

For Ericsson 2 node

<RODAP:ROU=1;

ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

1 SL60 H'00000310 H'15400000 H'06400000 NO

END

<RODAP:ROU=3;

ROUTE DATA

ROU TYPE VARC VARI VARO FILTER

3 SL60 H'00000310 H'15400000 H'06300000 NO

END

Route Equipment Initiate

For Ericsson 1 node

E1-PRI QSIG trunk lines (B-channels)

<ROEDP:ROU=100,TRU=ALL;

ROUTE EQUIPMENT DATA

ROU TRU EQU SQU INDDAT CNTRL

100 001-1 001-0-30-01 H'000000000000

100 001-2 001-0-30-02 H'000000000000

100 001-3 001-0-30-03 H'000000000000

100 001-4 001-0-30-04 H'000000000000

100 001-5 001-0-30-05 H'000000000000

100 001-6 001-0-30-06 H'000000000000

100 001-7 001-0-30-07 H'000000000000

100 001-8 001-0-30-08 H'000000000000

100 001-9 001-0-30-09 H'000000000000

100 001-10 001-0-30-10 H'000000000000

100 001-11 001-0-30-11 H'000000000000

100 001-12 001-0-30-12 H'000000000000

100 001-13 001-0-30-13 H'000000000000

100 001-14 001-0-30-14 H'000000000000

100 001-15 001-0-30-15 H'000000000000

100 001-17 001-0-30-17 H'000000000000

100 001-18 001-0-30-18 H'000000000000

100 001-19 001-0-30-19 H'000000000000

100 001-20 001-0-30-20 H'000000000000

100 001-21 001-0-30-21 H'000000000000

100 001-22 001-0-30-22 H'000000000000

100 001-23 001-0-30-23 H'000000000000

100 001-24 001-0-30-24 H'000000000000

100 001-25 001-0-30-25 H'000000000000

100 001-26 001-0-30-26 H'000000000000

100 001-27 001-0-30-27 H'000000000000

100 001-28 001-0-30-28 H'000000000000

100 001-29 001-0-30-29 H'000000000000

100 001-30 001-0-30-30 H'000000000000

100 001-31 001-0-30-31 H'000000000000

END

<ROEDP:ROU=101,TRU=ALL;

ROUTE EQUIPMENT DATA

ROU TRU EQU SQU INDDAT CNTRL

101 001-1 001-0-40-01 H'000000000000

101 001-2 001-0-40-02 H'000000000000

101 001-3 001-0-40-03 H'000000000000

101 001-4 001-0-40-04 H'000000000000

101 001-5 001-0-40-05 H'000000000000

101 001-6 001-0-40-06 H'000000000000

101 001-7 001-0-40-07 H'000000000000

101 001-8 001-0-40-08 H'000000000000

101 001-9 001-0-40-09 H'000000000000

101 001-10 001-0-40-10 H'000000000000

101 001-11 001-0-40-11 H'000000000000

101 001-12 001-0-40-12 H'000000000000

101 001-13 001-0-40-13 H'000000000000

101 001-14 001-0-40-14 H'000000000000

101 001-15 001-0-40-15 H'000000000000

101 001-17 001-0-40-17 H'000000000000

101 001-18 001-0-40-18 H'000000000000

101 001-19 001-0-40-19 H'000000000000

101 001-20 001-0-40-20 H'000000000000

101 001-21 001-0-40-21 H'000000000000

101 001-22 001-0-40-22 H'000000000000

101 001-23 001-0-40-23 H'000000000000

101 001-24 001-0-40-24 H'000000000000

101 001-25 001-0-40-25 H'000000000000

101 001-26 001-0-40-26 H'000000000000

101 001-27 001-0-40-27 H'000000000000

101 001-28 001-0-40-28 H'000000000000

101 001-29 001-0-40-29 H'000000000000

101 001-30 001-0-40-30 H'000000000000

101 001-31 001-0-40-31 H'000000000000

END

For Ericsson 2 node

<ROEDP:ROU=1,TRU=ALL;

ROUTE EQUIPMENT DATA

ROU TRU EQU IP ADDRESS SQU INDDAT CNTRL

1 001-1 001-1-40-01 H'000000000000

1 001-2 001-1-40-02 H'000000000000

1 001-3 001-1-40-03 H'000000000000

1 001-4 001-1-40-04 H'000000000000

1 001-5 001-1-40-05 H'000000000000

1 001-6 001-1-40-06 H'000000000000

1 001-7 001-1-40-07 H'000000000000

1 001-8 001-1-40-08 H'000000000000

1 001-9 001-1-40-09 H'000000000000

1 001-10 001-1-40-10 H'000000000000

1 001-11 001-1-40-11 H'000000000000

1 001-12 001-1-40-12 H'000000000000

1 001-13 001-1-40-13 H'000000000000

1 001-14 001-1-40-14 H'000000000000

1 001-15 001-1-40-15 H'000000000000

1 001-17 001-1-40-17 H'000000000000

1 001-18 001-1-40-18 H'000000000000

1 001-19 001-1-40-19 H'000000000000

1 001-20 001-1-40-20 H'000000000000

1 001-21 001-1-40-21 H'000000000000

1 001-22 001-1-40-22 H'000000000000

1 001-23 001-1-40-23 H'000000000000

1 001-24 001-1-40-24 H'000000000000

1 001-25 001-1-40-25 H'000000000000

1 001-26 001-1-40-26 H'000000000000

1 001-27 001-1-40-27 H'000000000000

1 001-28 001-1-40-28 H'000000000000

1 001-29 001-1-40-29 H'000000000000

1 001-30 001-1-40-30 H'000000000000

1 001-31 001-1-40-31 H'000000000000

END

<ROEDP:ROU=3,TRU=ALL;

ROUTE EQUIPMENT DATA

ROU TRU EQU IP ADDRESS SQU INDDAT CNTRL

3 001-1 001-1-50-01 H'000000000000

3 001-2 001-1-50-02 H'000000000000

3 001-3 001-1-50-03 H'000000000000

3 001-4 001-1-50-04 H'000000000000

3 001-5 001-1-50-05 H'000000000000

3 001-6 001-1-50-06 H'000000000000

3 001-7 001-1-50-07 H'000000000000

3 001-8 001-1-50-08 H'000000000000

3 001-9 001-1-50-09 H'000000000000

3 001-10 001-1-50-10 H'000000000000

3 001-11 001-1-50-11 H'000000000000

3 001-12 001-1-50-12 H'000000000000

3 001-13 001-1-50-13 H'000000000000

3 001-14 001-1-50-14 H'000000000000

3 001-15 001-1-50-15 H'000000000000

3 001-17 001-1-50-17 H'000000000000

3 001-18 001-1-50-18 H'000000000000

3 001-19 001-1-50-19 H'000000000000

3 001-20 001-1-50-20 H'000000000000

3 001-21 001-1-50-21 H'000000000000

3 001-22 001-1-50-22 H'000000000000

3 001-23 001-1-50-23 H'000000000000

3 001-24 001-1-50-24 H'000000000000

3 001-25 001-1-50-25 H'000000000000

3 001-26 001-1-50-26 H'000000000000

3 001-27 001-1-50-27 H'000000000000

3 001-28 001-1-50-28 H'000000000000

3 001-29 001-1-50-29 H'000000000000

3 001-30 001-1-50-30 H'000000000000

3 001-31 001-1-50-31 H'000000000000

END

Route External Destination Data Initiate

For Ericsson 1 PSTN ROUTE

NANSI:NUMTYP=ED,NUMSE=650;

RODDI:DEST=650,ROU=100,ADC=1707000000000250107001100,SRT=1;

NANLS:EXL=650,MIN=10,MAX=10;

For Ericsson 1 node

Route and Access Code for the trunk Information- Note Route 100 & 101 are the PRI QSIG

<RODDP:DEST=ALL;

EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

21 1 1707000000000250107001100 0 3 0

25 100 1707000000000250107001100 0 3 0

31 11 1005000000000250000000000 0 3 0

35 11 0606000000000250106001100 0 3 0

36 6 0115000000000250001000000 0 3 0

38 8 0115000000000250001000000 0 3 0

30 101 1707000000000250107001100 0 1 0

42 100 0707000000000250107001100 0 1 0

550 11 0606000000000250106001100 0 1 0

551 101 0707000000000250107001100 0 1 0

560 11 0606000000000250106001100 0 1 0

650 100 1707000000000250107001100 0 1 0

666 100 0707000000000250107001100 0 1 0

950 11 0606000000000250106001100 0 7 0

END

For Ericsson 2 node

Route and Access Code for the trunk Information- Note Route 1 & 3 are the PRI QSIG

<RODDP:DEST=ALL;

EXTERNAL DESTINATION ROUTE DATA

DEST DRN ROU CHO CUST ADC TRC SRT NUMACK PRE

11 1 1707000000000250107001100 0 1 0

21 1 1727000000000250107001100 0 1 0

23 3 1727000000000250107001100 0 1 0

31 11 1005200000000250100001000 0 3 0

30 3 1707000000000250107001100 0 1 0

50 11 0606000000000250106001100 0 1 0

550 11 0606000000000250106001100 0 1 0

551 3 0707100000000250107001100 0 1 0

560 11 0606000000000250106001100 0 1 0

60 11 0606000000000250106001100 0 1 0

777 1 0707000000000250007001100 0 1 0

950 11 0606000000000250106001100 0 7 0

END

Overlap/Enbloc sending

For Ericsson 1 node

To do overlap sending First remove access code

<NANLR:EXL=30;

To do Enbloc sending

<NANLS:EXL=30,MIN=4,MAX=4;

Key System Directory

For Ericsson 1 node

<KSDDP:DIR=1154;

KEY SYSTEM DIRECTORY DATA

DIR CUST EQU CAT ADN ODN CALALT TIMER

1154 001-0-20-03 - 1 0

END

<KSDDP:DIR=1155;

KEY SYSTEM DIRECTORY DATA

DIR CUST EQU CAT ADN ODN CALALT TIMER

1155 001-0-20-04 - 1 0

END

For Ericsson 2 node

<KSDDP:DIR=4200&&4201;

KEY SYSTEM DIRECTORY DATA

DIR CUST EQU CAT ADN ODN CALALT TIMER

4200 001-1-20-00 1 1 0

4201 001-1-20-01 1 1 0

END

Calling/Connected Name and Number Restrictions

To configure Calling/Connected Name and Number Restricted, use the following command:

<KSCAC:DIR=1154&&1155,ADC=00010013010000;

To configure Calling/Connected Name and Number Allowed, use the following command:

<KSCAC:DIR=1154&&1155,ADC=00100013010000;

To remove Name, use the following command:

<NIINE:DIR=1154;//REMOVE NAME

To add Name, use the following command:

<NIINI:DIR=1154,NAME1="BC12-1",NAME2="FOUR",PRES=20; //ADD NAME

To print Station's Name, use the following command:

<NIINP:DIR=1154&&1155;

EXTENSION NAMES

DIR NAME1 NAME2 PRES INFO

1154 BC12-1 FOUR 10

1155 BC12-1 FIVE 10

END

Path Replacement (Route Optimization)

To enable/disable Path Replacement, use the following command:

<ASPAC:PARNUM=66,PARVAL=1; //Route optimization allowed. --- FORWARD
<ASPAC:PARNUM=66,PARVAL=0; //Route optimization NOT allowed.
Call Diversion on Busy/No Reply
To enable/disable Diversion on Busy/No Reply, use the following command:
<CDINI:DIR=1154,DIV=4200; // CALL DIVERSION INDIVIDUAL NUMBER INITIATE
<CDINE:DIR=1154; // CALL DIVERSION INDIVIDUAL NUMBER END
Diversion Counter
<ASUVP:PARNUM=121; // check current setting for maximum number of hop diversions
<ASPAC:PARNUM=121,PARVAL= VALUE; // To set maximum number of hop diversions where VALUE range is 0-255
<ASUVP:PARNUM=121;
APPLICATION SYSTEM PARAMETER VALUES FOR UNIT
PARNUM CHA PARVAL MINVAL MAXVAL UNIT REMARK
121 YES 12 0 255 RMP
END
Ericsson MD-110 Software Version

For Ericsson 1 node

<CADAP;

CALENDAR DATA

IDENTITY=ACM-1

VERSION=CXP1010101/2/BC12SP5/R2A

11:19:20

MON 15 OCT 2006

END

For Ericsson 2 node

<CADAP;
CALENDAR DATA
IDENTITY=DANDS-EURO
VERSION=CXP1010001/5/BC11SP13/R3A
CALENDAR TIME NOT VALID
17:23:44
MON 15 AUG 2006
END
Configuring Cisco CallManager
ECMA Protocol Service Parameter

CMM-E1 Gateway Configuration
Partitions Configuration

Calling Search Space Configuration

Enbloc Route Pattern Configuration

Overlap Sending Route Pattern

PSTN Route Pattern Configuration
Translation Pattern for Incoming Calls

CLIR Route Pattern Config

CNIR Route Pattern Config

COLR Translation Pattern Config
CONR Route Pattern Configuration
MWI lamp On/Off Configuration

Note: Not Applicable. Standard QSIG SS-MWI is not supported on Ericsson MD110 BC12 SP5

CallBack Service Parameters

Note: Not Applicable. Standard QSIG Call Completion (CallBack) is not supported on Ericsson MD110 BC12 SP5 when set to ECMA QSIG variant.

Path Replacement Service Parameter
Note: Not Applicable. Standard QSIG ANF Path Replacement is not supported on Ericsson MD110 BC12 SP5 when set to ECMA QSIG variant.
Forward by Reroute Service Parameter
Note: Not Applicable. Standard QSIG Call Forward by ReRoute is not supported on Ericsson MD110 BC12 SP5 when set to ECMA QSIG variant.
IP phone Configuration

Cisco 3845 w/ VWIC-2MFT-E1 Configuration

tony_3845#sh ver

Cisco IOS Software, 3800 Software (C3845-ENTSERVICESK9-M), Version 12.3(14)T6,

RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Thu 05-Jan-06 02:57 by dchih

ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)

tony_3845 uptime is 2 hours, 21 minutes

System returned to ROM by reload at 18:34:34 UTC Thu May 4 2006

System image file is "flash:c3845-entservicesk9-mz.123-14.T6.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 3845 (revision 1.0) with 486400K/37888K bytes of memory.

Processor board ID FTX0933A1JA

2 Gigabit Ethernet interfaces

62 Serial interfaces

2 Channelized E1/PRI ports

2 Channelized T1/PRI ports

DRAM configuration is 64 bits wide with parity enabled.

479K bytes of NVRAM.

125184K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

tony_3845#sh run

Building configuration...

Current configuration : 3246 bytes

!

version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname tony_3845

!

boot-start-marker

boot system flash:c3845-entservicesk9-mz.123-14.T6.bin

boot-end-marker

!

logging buffered 100000000 debugging

enable password cisco

!

no aaa new-model

!

resource policy

!

no network-clock-participate slot 3

no network-clock-participate wic 0

voice-card 0

no dspfarm

!

voice-card 3

dspfarm

!

ip subnet-zero

ip cef

!

!

no ip dhcp use vrf connected

!

!

no ip domain lookup

ip host CM-BARZA 172.20.110.254

ip host CM-CHIVAS 172.20.8.254

no ftp-server write-enable

isdn switch-type primary-4ess

!

!

!

controller T1 0/0/0

framing esf

linecode b8zs

!

controller T1 0/0/1

framing esf

linecode b8zs

!

controller E1 3/0/0

pri-group timeslots 1-31 service mgcp

!

controller E1 3/0/1

pri-group timeslots 1-31 service mgcp

!

!

!

interface GigabitEthernet0/0

ip address 172.20.8.26 255.255.255.0

duplex auto

speed auto

media-type rj45

negotiation auto

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

media-type rj45

negotiation auto

!

interface Serial3/0/0:15

no ip address

isdn switch-type primary-qsig

isdn protocol-emulate network

isdn incoming-voice voice

isdn T310 120000

isdn bind-l3 ccm-manager

no cdp enable

!

interface Serial3/0/1:15

no ip address

isdn switch-type primary-qsig

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

ip default-gateway 172.20.8.1

ip classless

ip route 0.0.0.0 0.0.0.0 172.20.8.1

!

!

ip http server

no ip http secure-server

!

!

!

!

control-plane

!

!

!

voice-port 3/0/0:15

!

voice-port 3/0/1:15

!

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server CM-CHIVAS

ccm-manager config

!

mgcp

mgcp call-agent CM-CHIVAS 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

!

!

!

line con 0

password cisco

stopbits 1

line aux 0

stopbits 1

line vty 0 4

password cisco

login

!

scheduler allocate 20000 1000

!

end

tony_3845#

Acronyms

Acronym
Definitions

ANF-PR

Additional Network Feature Path Replacement

AOC Advice-of-charge

Information element is sent with the connection setup information for incoming Euro-ISDN connections. The AOC IE is used for call charge calculation

CCM

Cisco Unified Call Manager

CCBS

Call Completion to Busy Subscriber

CCNR

Call Completion on No Reply

CFB

Call Forwarding on Busy

CFNR

Call Forwarding No Reply

CFU

Call Forwarding Unconditional

CLIP

Calling Line (Number) Identification Presentation

CLIR

Calling Line (Number) Identification Restriction

CNIP

Calling Name Identification Presentation

CNIR

Calling Name Identification Restriction

COLP

Connected Line (Number) Identification Presentation

COLR

Connected Line (Number) Identification Restriction

CONP

Connected Name Identification Presentation

CONR

Connected Name Identification Restriction

CT

Call Transfer

MWI

Message Waiting Indicator

Important Information
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 526-4100
European Headquarters

Cisco Systems International BV

Haarlerbergpark

Haarlerbergweg 13-19

1101 CH Amsterdam

The Netherlands

www-europe.cisco.com

Tel: 31 0 20 357 1000

Fax: 31 0 20 357 1100
Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

www.cisco.com

Tel: 408 526-7660

Fax: 408 527-0883
Asia Pacific Headquarters

Cisco Systems, Inc.

Capital Tower

168 Robinson Road

#22-01 to #29-01

Singapore 068912

www.cisco.com

Tel: +65 317 7777

Fax: +65 317 7799
Cisco Systems has more than 200 offices in the following countries and regions. Addresses, phone numbers, and fax numbers are listed on
the Cisco Web site at www.cisco.com/go/offices.
Argentina · Australia · Austria · Belgium · Brazil · Bulgaria · Canada · Chile · China PRC · Colombia · Costa Rica · Croatia · Czech Republic · Denmark · Dubai, UAE · Finland · France · Germany · Greece · Hong Kong SAR · Hungary · India · Indonesia · Ireland · Israel · Italy · Japan · Korea · Luxembourg · Malaysia · Mexico · The Netherlands · New Zealand · Norway · Peru · Philippines · Poland · Portugal · Puerto Rico · Romania · Russia · Saudi Arabia · Scotland · Singapore · Slovakia · Slovenia · South Africa · Spain · Sweden · Switzerland · Taiwan · Thailand · Turkey Ukraine · United Kingdom · United States · Venezuela · Vietnam · Zimbabwe
© © 2006 Cisco Systems, Inc. All rights reserved.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0601R)

Printed in the USA