When you use a Private Branch Exchange (PBX) connected to a Cisco CallManager through an E1 Q Interface Signalling Protocol (QSIG) in a Cisco voice gateway using Media Gateway Control Protocol (MGCP), the calling name is not displayed. Forwarded calls from different vendors are also dropped.
There are no specific requirements for this document.
The information in this document is based on Cisco CallManager 4.x.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
The QSIG protocol, a series of international standards, defines services and signaling protocols for Private Integrated Services Networks (PISNs). These standards use Integrated Services Digital Network (ISDN) concepts and conform to the framework of International Standards for Open Systems Interconnection as defined by ISO/IEC. The QSIG protocol acts as a variant of ISDN D-channel voice signaling. The ISDN Q.921 and Q.931 standards provide the basis for QSIG protocol, which sets a worldwide standard for PBX interconnection.
In a basic QSIG call, a user in a Private Integrated Services Network Exchange (PINX) can place a call to a user that is in a remote PINX. The called party receives the caller name or number as the call rings. The calling party receives the called name and number when the user phone rings in the remote PINX. All the features that are available as a PBX user operate transparently across the network. QSIG protocol provides supplementary and additional network features, as defined for PISNs, if the corresponding set of QSIG features are supported by both ends of the call.
When you use QSIG protocol version 2, if a Cisco IP phone forwards a call to another Cisco IP phone that is placed from a third party phone, the first phone call is dropped. Similarly, when a third party phone call is forwarded to another third party phone that is placed from a Cisco IP phone, the first phone call is dropped.
When you use QSIG protocol and you call a Cisco IP phone from a phone connected to a third party PBX or a third party phone from a Cisco IP phone, the third party phone calling name is shown in the Cisco IP phone, but the Cisco IP phone calling name is not shown in the third party phone. In other words, calling name information is not passed from Cisco CallManager to the third party PBX. This issue is documented in Cisco bug ID CSCee08424 (registered customers only) .
These problems can occur if the facility message from third party PBX cannot be decoded by the Cisco CallManager.
In order to create Cisco CallManager compatibility with your version of the QSIG protocol, configure the ASN.1 ROSE OID encoding and QSIG Variant service parameters. The problem described in this document can be solved when you change the ASN.1 ROSE OID encoding to Use Global Value (ECMA). Complete the procedure in this section in order to change the ASN.1 ROSE OID.
Note: The ASN.1 ROSE OID parameter specifies how to encode the Invoke Object ID (OID) for Remote Operations Service Element (ROSE) operations. Use Local Value (supported by most telephony systems) should be used when you use QSIG Variant ISO. Use Global Value (ISO) should be used only if the connected PBX does not support Local Value. Use Global Value (ECMA) should be used if QSIG Variant is ECMA. This is a required field. The default is Use Local Value.
Go to the CallManager Administration page and choose Services > Service Parameters in order to go to System Parameters.
Go to the Advanced tab.
Find the Parameter Name ASN.1 ROSE OID Encoding under Clusterwide Parameters (Device - PRI and MGCP gateway) and change the parameter value to Use Global Value (ECMA). This is used if the Q.SIG Variant service parameter is set to ECMA (Protocol Profile 0x91).
Note: The default value for ASN.1 ROSE OID Encoding is Use Local Value, which is supported by most telephony systems and must be used when the Q.SIG Variant service parameter is set to ISO (Protocol Profile 0x9F).
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.