Document ID: 99875
The Cisco Unity Message Repository (UMR), built into Cisco Unity 3.x and later, allows outside callers to leave messages for users when their primary Microsoft Exchange server is offline. Messages are temporarily stored on the Cisco Unity server in the \CommServer\unityMTA directory and can be accessed through a special UMR conversation. When the primary Exchange server comes back online, Cisco Unity begins to pass the messages as normal into the correct message store.
This document explains some of the UMR error messages and describes the steps necessary to troubleshoot and overcome those errors.
Cisco recommends that you understand how Cisco Unity works before you read this document. Refer to White Paper: Cisco Unity Data Architecture and How Cisco Unity Works (Version 3.x) Overview for more information.
The information in this document is based on Cisco Unity 3.0 or later with Microsoft Exchange.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Undelivered Voicemail messages are found in the commserver\unitymta\failed directory. This error message is recorded in the Event Viewer Application log:
Event Type: Warning Event Source: CiscoUnity_UMR Event Category: UMR Thread Error Event ID: 155 Date: 8/13/2007 Time: 6:50:53 AM User: N/A Computer: HTMUNIT01 Description:One or more messages have been held in the UnityMTA directory for 30 days. This directory is used by the Unity Messaging Repository service to temporarily store voice messages left by unidentified callers when the Partner Mail Server (CN=AAA0001/OU=CIS/OU=CISCO_TS/OU=TS/O=CISCO) is not available. Normally, these messages are delivered shortly after Cisco Unity detects that the partner mail server has come back on-line. Check that the partner mail server is on-line, including the mailstore, and that Cisco Unity can connect to it. If the partner mail server is on-line and reachable, to diagnose the problem, enable all the micro traces for the AvUMRSyncSvr service, restart the service, and then examine the logs. Message information: Recipient: cISCO 0x000012D0
Normally, when Exchange goes down, the UMR feature allows Cisco Unity to take outside caller messages. When Cisco Unity is in the UMR mode, the voicemail messages are stored temporarily on the Cisco Unity server in the \CommServer\UnityMTA directory and not Exchange. This ensures that the subscribers can access any new voicemail messages that are stored in the \CommServer\UnityMTA directory. Once Exchange comes back online, a notification is sent by the AVNotifier service that states Exchange is back online. All messages temporarily stored in the Cisco Unity Message Transfer Agent (MTA) folder, \Commserver\unityMTA, flow straight to Microsoft Exchange
In order to overcome the One or more messages have been held in the UnityMTA directory for 30 days error:
Browse to the failed subfolder located under \\commserver\UnityMTA\. Move the voicemail messages manually to the parent MTA folder, \\commserver\UnityMTA\, so that Cisco Unity attempts to deliver those voicemail messages. The error message is not likely to appear again.
Since these voicemail messages are old (30 days), you can select them all, and delete them.
When the voicemail messages are stored in the MTA folder, there are two files with the name in the directory, one with a .wav file extension, which is the voice message itself, and one with a .txt extension, which is the routing file that the AvUMRSyncSvr uses when it addresses the message. If you do not have the .wav file, it means the files were sent successfully. In this case, only the routing files remain. You can delete them.
When you attempt to delete any of the files, the Cannot delete <file name>: There has been a sharing violation. The source or destination file may be in use. message can appear.
This message indicates that you need to stop the AvUMRSynchSvr Cisco Unity service first in order to be able to delete those files. Upon deletion of the files, restart AvUMRSynchSvr.
Once you have deleted all the files, the warning/error message stops.
Problem: Attempts to deliver Unity Message Repository messages have failed due to Unity configuration or connectivity issues with the Partner Mail Server
Cisco Unity users cannot receive voice mail and can not access their voice mail box, and this error message appears in the Event Log:
Event Type: Error Event Source: CiscoUnity_UMR Event Category: UMR Thread Error Event ID: 137 Date: 2/25/2009 Time: 9:28:13 AM User: N/A Computer: IOTUTYP01PW Description: Attempts to deliver Unity Message Repository messages have failed due to Unity configuration or connectivity issues with the Partner Mail Server. AvUMRSyncSvr will suspend message delivery for 300 seconds, after which message delivery will be attempted again. During this outage, messages may accumulate in the temporary store. 0x00002580
This issue occurs when the partner exchange is off line and Unity runs in UMR mode, which results in the AvUMRSyncSvr service error.
In order to resolve this issue, complete these steps:
Run the Permissions Wizard from the Cisco Unity Tools Depot and make sure that the Unity server points to the correct mailsore where the users are located.
Make sure that the service accounts meet all the rights and permissions described in Permissions Set By the Cisco Unity Permissions Wizard .
Make sure that there is network connectivity between Cisco Unity and Exchange server. Refer to Use Ping to Test Network Connectivity and Throughput for more information.
Make sure that the NIC settings are proper on the Cisco Unity server or the Exchange server or the switch to which the Unity connects. Refer to NIC Set to Auto Detect Line Speed and Duplex, Which Results in Low Throughput for more information.
Problem: The Unity Message Repository cannot communicate with the Partner Mail Server to deliver messages
After an upgrade to Cisco Unity 7.x, these UMR warnings are received, and undelivered voicemail messages are found in the UnityMTA folder.
Event Type: Warning Event Source: CiscoUnity_UMR Event Category: UMR Thread Error Event ID: 110 Date: 9/15/2009 Time: 10:43:54 PM User: N/A Computer: CIN110UM01 Description: The Unity Message Repository cannot communicate with the Partner Mail Server to deliver messages. Messages will be held in the temporary store until the mail server is available.
Complete these steps:
Set this registry value to 1.
HKLM > Software > Active Voice > AvWm > 1.00 > Disable Server Status Check (DWORD)
Note: This disables the server ping check and causes AvWm to assume that all Exchange servers are up all the time.
Now, the undelivered voicemail messages are sent.
Migrate to a new partner Exchange server.
Set this registry value back to 0.
HKLM > Software > Active Voice > AvWm > 1.00 > Disable Server Status Check (DWORD)
Move the Cisco Unity mailbox to the new Exchange server. Refer Cisco Unity: Moving Mailboxes Between Exchange Servers for more information.
On the Cisco Unity Server, choose Start > Settings > Control Panel, and choose the Add/Remove Programs option, and then choose the Message Store Configuration Wizard (MSCW) to run the MSCW.
Delete the MAPI profile, and reboot the Cisco Unity server.
You hear the Message Server is offline message. Additionally, the D:\ drive on the Exchange server is full.
Event Type: Warning Event Source: CiscoUnity_UMR Event Category: UMR Thread Error Event ID: 112 Date: 11/24/2010 Time: 11:44:10 AM User: N/A Computer: TXCMASMCD001 Description: The Unity Message Repository still cannot communicate with the Partner Mail Server to deliver messages. Messages will continue to be held in the temporary store until the mail server is available. 240
Note: The messages are stuck in the MTA folder. Delete a large volume of Exchange log files after dismounting the mailstore.
Complete these steps in order to resolve the issue:
Open the Exchange Management Console (EMC).
In the console tree, expand Server Configuration, and click Mailbox.
In the work pane, right-click the storage group for which you want to enable circular logging, and open its Properties.
Check the Enable circular logging check box.
Note: After this you need to restart the Microsoft Exchange Information Store service (MSExchangeIS).
Click Start, click Run, and then type services.msc in order to start the Services snap-in.
Locate the Microsoft Exchange Information Store service (MSExchangeIS), and restart the service.
Mount the mailstore back, and restart the UMRsync service in Unity box.
- Cisco Unity Remains in UMR Mode After Exchange Back Online
- How to Start Cisco Unity in UMR Mode
- Cisco Unity: Defining the Unity Message Repository
- Voice Technology Support
- Voice and Unified Communications Product Support
- Troubleshooting Cisco IP Telephony
- Technical Support & Documentation - Cisco Systems
|Updated: Nov 14, 2007||Document ID: 99875|