ATM and Layer 3 Module Specifications

This appendix describes the specifications for route processors, switch processors, port adapters, carrier modules, and interface modules used in ATM and Layer 3 systems. This appendix includes the following sections:

Component Specifications
Agency Approvals
Heat Dissipation and Watts
Module Part Numbers
Maximum Station-to-Station Cabling Distances
GBIC Cable Distances and Modal Bandwidths
Fiber-Optic Power Levels

Note All information pertains to both the ATM and Layer 3 platforms, unless differences between the platforms or individual systems are noted in the text.

Component Specifications

Table A-1 lists component specifications and standards compliance information for route processors, switch processors, port adapters, carrier modules, and interface modules used in the ATM and Layer 3 switch routers.

Table A-1: Component Specifications

Description	Specifications
Dimensions (H x W x D)	Route processor: 1.2 x 14.4 x 16 in (3.0 x 36.6 x 40.6 cm) Switch processor: 1.2 x 14.4 x 16 in. (3.0 x 36.6 x 40.6 cm) Port adapter: 1.2 x 6.5 x 10 in. (3.0 x 16.5 x 25.4 cm) Carrier module: 1.2 x 14.4 x 16 in. (3.0 x 36.6 x 40.6 cm) Interface module: 1.2 x 14.4 x 16 in. (3.0 x 36.6 x 40.6 cm) Interface module (OC-48c): 2.37 x 14.4 x 16.26 in. (3.0 x 36.6 x 40.6 cm)
Weight	Route Processor: 6.85 lb (3.09 kg) Switch processor: 3.55 lb. (1.60 kg) Port adapter (approximately): 1.10 lb (0.50 kg) Carrier module: 3.55 lb (1.60 kg) Interface module: 3.55 lb (1.60 kg)
Route processor capacity	Catalyst 8540 CSR: 40-Gbps Catalyst 8540 MSR: 20-Gbps Catalyst 8510 CSR: 10-Gbps Catalyst 8510 MSR: 5-Gbps LightStream 1010: 5-Gbps Catalyst 5500: 5-Gbps
Route processor microprocessor	100-MHz MIP¹ R4700
Route processor memory Catalyst 8500 CSR	16 MB Flash memory SIMM² 256 KB boot EPROM³ 128 KB SRAM⁴ 8-, 16-, or 20-MB Intel series 2+ Flash PC Cards Catalyst 8540 CSR: 256 MB DRAM⁵ Catalyst 8510 CSR: 64 MB DRAM
Route processor memory Catalyst 8500 MSR, Lightstream 1010, and Catalyst 5500	8-MB Flash memory SIMM 32 MB DRAM default for FC-PCQ 64 MB DRAM default for FC-PFQ 256 KB boot EPROM 128 KB SRAM 8-, 16-, or 20 MB Intel Series 2+ Flash PC Card
Operating temperature	32 to122ºF (0 to 50ºC)
Nonoperating temperature	-40 to 167ºF (-40 to 75ºC)
Humidity	10 to 90%, noncondensing
Altitude	-500 to 10,000 ft (-52 to 3048 m)
Interface timing	Loop timing, Stratum 4 accuracy clock for self-timing; synchronous, SRTS⁶, or adaptive clocking for CBR⁷ traffic
Interface ports	RJ-45 IEEE 802.3 Ethernet 10BaseT port DB-25 console port for an administration workstation
MIBs	SNMP⁸MIB II (RFC 1213), Interface table MIB (RFC 1573), CISCO-CDP-MIB, CISCO-BRIDGE-MIB

¹MIP = MultiChannel Interface Processor
²SIMM = single in-line memory module
³EPROM = erasable programmable read-only memory
⁴SRAM = static random-access memory
⁵DRAM = dynamic random-access memory
⁶SRTS = synchronous residual time stamp
⁷CBR = constant bit rate
⁸SNMP = Simple Network Management Protocol

Agency Approvals

Table A-2 lists the agency approvals and electromagnetic interference (EMI) specifications for the ATM and Layer 3 systems.

Table A-2: Regulatory Compliance Standards for the ATM and Layer 3 Systems

Description

System

Specifications

Compliance

ATM

Layer 3

CE Marking

Safety

ATM

Layer 3

UL 1950¹, 21CFR1040², CSA 950³, EN60825, IEC60950⁴, IEC 60325, AS/NZS 3260⁵, EN 60950⁶, TS 001⁷,

EMC standards

ATM

Layer 3

With UTP cables:

FCC Part 15 Class A (CFR 47, Part 15)
CISPR 22 Class A
EN 55022 Class A
VCCI Class A
AS/NZS 3548 Class A

With FTP cables:

EN 55022 Class B
CISPR 22 Class B
VCCI Class B
ENSS024
ENS0082-1 (1997)

¹UL = Underwriters Laboratories
²CFR = Code of Federal Regulations
³CSA = Canadian Standards Association
⁴IEC = International Electrotechnical Commission
⁵AS/NZS = Australia/New Zealand Standards
⁶EN = European Norm
⁷TS = Technical Standard

Heat Dissipation and Watts

Table A-3 lists the heat dissipation and watts for the ATM and Layer 3 port adapters and interface modules.The following numbers are based on a 48VDC as the reference for the current.

Table A-3: Module Power Consumption

Port Adapters and Interface Modules	Product Number	Heat Dissipation
		Current	Watts
25-Mbps port adapters	C85MS-ATM25-4P WAI-ATM25-12P	0.2A	9.6W
155-Mbps port adapters	WAI-OC-3-4MM WAI-OC-3-4SM WAI-OC3-1S3M WAI-C3-4U5	0.2A	9.6W
16-port OC-3c interface modules	C85MS-16F-OC3MM	0.4A	19.2W
622-Mbps port adapters	WAI-OC12-1SM WAI-OC12-1MM	0.2A	9.6W
Four-port OC-12c interface module	C85MS-4F-OC12SS C85MS-4F-OC12MM	0.5A	24W
OC-48c (1 OC-48c plus 4 OC-12c port or 2 OC-48c port) interface modules	C85MS-2F-OC48LR C85MS-1F4S-OC48LR C85MS-2F-OC48SS C85MS-1F4S-OC48SS C85MS-1F4M-OC48SS	1.7A	81.6W
T1 and E1 port adapters	WAI-E1-4RJ48 WAI-T1-4RJ48 WAI-E1-4BNC	0.2A	9.6W
Eight-port T1 and E1 IMA port adapters	C85MS-8T1-IMA C85MS-8E1-IMA-120	0.4A	19.2W
CE1 Frame Relay port adapters	C85MS-4E1-FRRJ48	0.2A	9.6W
CES T1 and E1 port adapters	WAI-E1C-4BNC WAI-E1C-4RJ48 WAI-T1C-4RJ48	0.2A	9.6W
DS3 and E3 port adapters	WAI-T3-2BNC WAI-T3-4BNC WAI-E3-2BNC WAI-E3-4BNC	0.2A	9.6W
CDS3 Frame Relay port adapters	C85MS-1DS3-FRBNC	0.2A	9.6W
Enhanced Catalyst 8540 ATM Router Module¹	C8540-ARM2	1.5A	72W
Catalyst 8540 ATM Router Module²	C8540-ARM	1.5A	72W
Catalyst 8510 ATM Router Module³^, ⁴	C8510-ARM	0.5A	24W
Two-port Gigabit Ethernet interface modules	C85GE-2X-16K C85GE-2X-64K	2A	96W
Eight-port Gigabit Ethernet interface modules	C85GE-8X-64K	3A	144W
Two-port Enhanced Gigabit Ethernet interface modules	C85GE-2X-16K C85EGE-2X-64K C85EGE-2X-256K	2A	96W
One-port Gigabit Ethernet interface modules	C85GE-1X-16K C85GE-1X-64K	0.4A	19.2W
16-port 10/100BASE-T interface modules	C85FE-16T-16K C85FE-16T-64K	2A	96W
Eight-port 10/100BASE-T interface modules	C85FE-8T-16K C85FE-8T-64K	0.4A	19.2W
16-port 100BASE-FX interface modules	C85FE-16F-16K C85FE-16F-64K	1.7A	81.6W
Eight-port 100BASE-FX interface modules	C85FE-8F-16K C85FE-8F-64K	1A	48W
OC-3c or OC-12c ATM uplink with enhanced Gigabit Ethernet interface modules	C85-10C12SGE-256K C85-1OC12MGE-256K C85-10C12MGE-64K C85-10C3GE-64K	2A	96W
OC-12c Packet-over-SONET uplink with enhanced Gigabit Ethernet interface modules	C85-POSOC12I-64K C85-POSOC12I-256K C85-POSOC12L-64K C85-POSOC12L-256K	2A	96W

¹Two internal ports, Ethernet processor interface.
²Two internal ports, Gigabit processor interface.
³One internal port. The ATM router module is not supported on the Catalyst 5500.
⁴The LightStream 1010 system software image does not include support for the ATM router module or Layer 3 features. You can download the Catalyst 8510 MSR image to a LightStream 1010 ATM switch router with ASP-C and FC-PFQ installed.

Module Part Numbers

Table A-4 lists the component number, type of ports, and their part numbers for the ATM and Layer 3 systems.

Table A-4: Port Adapter and Interface Module and Part Numbers

Component	No. and Type of Ports	Connectors	Part No.
Catalyst 8540 route processor	1 Ethernet	RJ-45	C8541CSR-RP
Catalyst 8540 multiservice route processor	1 Ethernet	RJ-45	C8545MSR-MRP4CLK
Catalyst 8540 multiservice route processor stratum 3	1 Ethernet	RJ-45	C8545MSR-MRP3CLK
Catalyst 8510 CSR Route Processor	1 Ethernet	RJ-45	C8510-SRP
Catalyst 8510 MSR Route Processor	1 Ethernet	RJ-45	C8515-MSRP
Route Processor	1 Ethernet	RJ-45	C8515-MSRP (Catalyst 8510 MSR)
LightStream 1010 Route Processor with FC-Per-Class Queuing	1 Ethernet	RJ-45	L1010-ASP-C-FC1
LightStream 1010 Route Processor with FC-Per-Flow Queuing	1 Ethernet	RJ-45	L1010-ASP-C-FCPFQ
Catalyst 8540 CSR Switch Processors	—	—	C8542CSR-SP
Catalyst 8540 MSR Switch Processor	—	—	C8546MSR-MSP-FCL
25-Mbps port adapter	4 25-Mbps ports	RJ-45 connectors	C85MS-ATM25-4P
25-Mbps port adapter	12 25-Mbps ports	RJ-45 connectors	WAI-ATM25-12P
155-Mbps port adapter	4 SONET STS-3c/SDH STM-1 multimode fiber ports	SC connectors	WAI-OC-3-4MM
	4 SONET STS-3c/SDH STM-1 single-mode fiber ports¹	SC connectors	WAI-OC-3-4SM
	4 SONET STS-3c/SDH STM-1: 1 single-mode, 3 multimode fiber ports	SC connectors	WAI-OC3-1S3M
	4 SONET STS-3c/SDH STM-1 UTP-5 ports	RJ-45 connectors	WAI-C3-4U5
16-port OC-3c interface module	16 SONET STS-3c/SDH STM-1 multimode fiber port	MT-RJ connectors	C85MS-16F-OC3MM
622-Mbps port adapter	1 SONET STS-12c/SDH STM-4c single-mode fiber port¹	SC connectors	WAI-OC12-1SM
622-Mbps port adapter	1 SONET STS-12c/SDH STM-4c multimode fiber port	SC connectors	WAI-OC12-1MM
Four-port OC-12c interface module	4 SONET STS-12c/SDH STM-4c single-mode fiber port	Dual SC connectors	C85MS-4F-OC12SS
Four-port OC-12c interface module	4 SONET STS-12c/SDH STM-4c multimode fiber port	Dual SC connectors	C85MS-4F-OC12MM
OC-48c interface module	2 SONET STS-48c/SDH STM-16c single-mode fiber port	Dual SC connectors	C85MS-2F-OC48LR C85MS-1F4S-OC48LR
	2 SONET STS-48/SDH STM-16c single-mode fiber port	Dual SC connectors	C85MS-2F-OC48SS
	1 SONET STS-48c/SDH STM-16c single-mode fiber port	Dual SC connectors	C85MS-1F4S-OC48SS
	4 SONET STS-12c/SDH STM-4c single-mode fiber port	Dual SC connectors	C85MS-1F4S-OC48SS
	1 SONET STS-48c/SDH STM-16c single-mode fiber port	Dual SC connectors	C85MS-1F4M-OC48SS
	4 SONET STS-12c/SDH STM-4c multimode fiber port	Dual SC connectors	C85MS-1F4M-OC48SS
T1 and E1 port adapters	4 E1 trunk ports	RJ-48 connectors	WAI-E1-4RJ48
	4 T1 trunk ports	RJ-48 connectors	WAI-T1-4RJ48
	4 E1 trunk ports	BNC connectors	WAI-E1-4BNC
Eight-port T1 and E1 IMA port adapter	8 T1 ports	RJ-48 connectors	C85MS-8T1-IMA
Eight-port T1 and E1 IMA port adapter	8 E1 ports	RJ-48 connectors	C85MS-8E1-IMA-120
CE1 Frame Relay port adapter	4 CE1 ports	RJ-48c connectors	C85MS-4E1-FRRJ48
CES T1 and E1 port adapters	4 E1 CES ports	BNC connectors	WAI-E1C-4BNC
	4 E1 CES ports	RJ-48 connectors	WAI-E1C-4RJ48
	4 T1 CES ports	RJ-48 connectors	WAI-T1C-4RJ48
DS3 and E3 port adapters	2 DS3 ports	BNC connectors	WAI-T3-2BNC
	4 DS3 ports	BNC connectors	WAI-T3-4BNC
	2 E3 ports	BNC connectors	WAI-E3-2BNC
	4 E3 ports	BNC connectors	WAI-E3-4BNC
CDS3 port adapter	1 DS3 Frame Relay port	BNC connectors	C85MS-1DS3-FRBNC
Enhanced Catalyst 8540 MSR ATM Router Module	2 256 KB Ethernet processor ports (internal)	—	C8540-ARM2
Catalyst 8540 ATM Router Module	2 64 KB Gigabit processor ports (internal)	—	C8540-ARM
Catalyst 8510 MSR ATM Router Module	1 64 KB Gigabit processor port (internal)	—	C8510-ARM
Eight-port Gigabit Ethernet interface module	8-port GE 64 KB	SC-type	C85GE-8X-64K
Two-port Gigabit Ethernet interface module	2-port GE 16 KB	SC-type	C85GE-2X-16K
Two-port Gigabit Ethernet interface module	2-port GE 64 KB	SC-type	C85GE-2X-64K
Two-port Gigabit Ethernet with ACL	2-port GE 16 KB with ACL	SC-type	C85GE-2XACL-16K
Two-port Gigabit Ethernet with ACL	2-port GE 64 KB with ACL	SC-type	C85GE-2XACL-64K
Two-port enhanced Gigabit Ethernet interface module	2-port GE 16 KB	SC-type	C85GE-2X-16K
	2-port GE 64 KB	SC-type	C85EGE-2X-64K
	2-port GE 256 KB	SC-type	C85EGE-2X-256K
One-port Gigabit Ethernet interface module	1-port GE 16 KB	SC-type	C85GE-1X-16K
One-port Gigabit Ethernet interface module	1-port GE 64 KB	SC-type	C85GE-1X-64K
16-port 10/100BASE-T interface module	16-port FE 16 KB	RJ-45	C85FE-16T-16K
16-port 10/100BASE-T interface module	16-port FE 64 KB	RJ-45	C85FE-16T-64K
16-port 10/100BASE-T interface module with ACL	16-port FE 16 KB with ACL	RJ-45	C85FE-16TACL-16K
16-port 10/100BASE-T interface module with ACL	16-port FE 64 KB with ACL	RJ-45	C85FE-16TACL-64K
Eight-port 10/100BASE-T interface module	8-port FE 16 KB	RJ-45	C85FE-8T-16K
Eight-port 10/100BASE-T interface module	8-port FE 64 KB	RJ-45	C85FE-8T-64K
16-port 100BASE-FX interface module	16-port FE 16 KB	MT-RJ	C85FE-16F-16K
16-port 100BASE-FX interface module	16-port FE 64 KB	MT-RJ	C85FE-16F-64K
16-port 100BASE-FX interface module with ACL	16-port FE 16 KB with ACL	MT-RJ	C85FE-16FACL-16K
16-port 100BASE-FX interface module with ACL	16-port FE 64 KB with ACL	MT-RJ	C85FE-16FACL-64K
Eight-port 100BASE-FX interface module	8-port FE 16 KB	MT-RJ	C85FE-8F-16K
Eight-port 100BASE-FX interface module	8-port FE 64 KB	MT-RJ	C85FE-8F-64K
One-port ATM Uplink with enhanced Gigabit Ethernet interface modules (OC-3c and OC-12c)	1-port ATM OC-12 SMF-IR Uplink + 1-port GE 256 KB	SC-type	C85-10C12SGE-256K
	1-port ATM OC12 SMF-IR Uplink + 1-port GE 64 KB	SC-type	C85-10C12SGE-64K
	1-port ATM OC12 MMF Uplink + 1-port GE 256 KB	SC-type	C85-1OC12MGE-256K
	1-port ATM OC-12 MMF Uplink + 1-port GE 64 KB	SC-type	C85-10C12MGE-64K
	1-port ATM OC3 SMF-IR Uplink + 1-port GE 64 KB	SC-type	C85-10C3GE-64K
One-port Packet-over-SONET (POS) uplink with enhanced Gigabit Ethernet interface module (OC-12c)	1-port POS OC12 STM-4 SMF-IR + 1-port GE 64 KB	SC-type	C85-POSOC12I-64K
	1-port POS OC12 STM-4 SMF-IR + 1-port GE 256 KB	SC-type	C85-POSOC12I-256K
	1-port POS OC12 STM-4 SMF-LR + 1-port GE 64 KB	SC-type	C85-POSOC12L-64K
	1-port POS OC12 STM-4 SMF-LR + 1-port GE 256 KB	SC-type	C85-POSOC12L-256K

¹ Available in intermediate and long reach fiber

Maximum Station-to-Station Cabling Distances

When you prepare your site for network connections to the switch router, consider the distance limitations for each signal type and the cabling required for each type of interface. Additional equipment needed might include transceivers, modems, channel service units (CSUs) or data service units (DSUs). You might need connections not provided by service providers, such as a network termination unit (NTU) for T1, E1, DS3, and E3 port adapters.

The length of your networks and the distances between connections depends on the type of signal, the signal speed, and the transmission media (the type of cabling used to transmit the signals). For example, multimode fiber-optic cable has a greater channel capacity than unshielded twisted-pair (UTP) cabling.

Note The distances and rate limits in this appendix are the IEEE-recommended maximum speeds and distances for signaling. However, you can get good results at speeds and distances far greater than these if you understand and can compensate for the electrical problems that might arise. Do so at your own risk.

Networking standards set recommended maximum distances between stations using fiber-optic and UTP cable. The maximum distances for network segments and connections depend on the type of transmission cable used; for example, unshielded twisted-pair (UTP), foil twisted-pair (FTP), single-mode, or multimode fiber-optic cable.

Table A-5 lists maximum station-to-station cabling distances and cable types for port adapters and interface modules used in ATM and Layer 3 systems.

Table A-5: Maximum Station-to-Station Cabling Distances

ATM Port Adapter and Interface Module	Cable	Cabling Distance
25-Mbps	Category 5 UTP cable	328 ft (100 m) with four or fewer separate cable segments on the path
OC-3c, 155 Mbps	Category 5 UTP cable	328 ft (100 m)
OC-3c, 155 Mbps	9/125 micron single-mode fiber	9 miles (15 km)
OC-3c, 155 Mbps	9/125 micron single-mode fiber, extended reach plus	18 miles (30 km)
OC-3c, 155 Mbps	9/125 micron single-mode fiber, long reach	25 miles (40 km)¹
OC-3c, 155 Mbps	9/125 micron multimode fiber, long reach	1.2 miles (2km)
OC-12c, 622 Mbps	Single-mode fiber	9 miles (15 km)¹
OC-12c, 622 Mbps	50/125-micron and 62.5/125-micron multimode fiber	1640 ft (500 m)
OC-48c, 2488 Mbps	Single-mode fiber, intermediate reach	9 miles (15 km) intermediate reach
OC-48c, 2488 Mbps	Single-mode fiber, long reach	50 miles (80 km)¹
T1, 1.544 Mbps	Category 5 twisted-pair	650 ft (198 m)
E1, 2.048 Mbps	Category 5 twisted-pair and FTP (120 ohms)	650 ft (198 m)
E1, 2.048 Mbps	Coaxial cable (75 ohms)	650 ft (198 m)
CE1, 2.048 Mbps	Category 5 twisted-pair	650 ft (198 m)
CES T1	Category 5 twisted-pair and FTP	650 ft (198 m) (5.5 dB attenuation at 772 kHz), 100-ohm, 24 AWG², UTP cable with RJ³-48c connectors
CES E1	Category 5 twisted-pair and FTP	820 ft (248.5 m) (6 dB attenuation at 1024 kHz), 100 ohm, 24 AWG, UTP cable with RJ-48c connectors
CES E1	Coaxial cable (75 ohms)	650 ft (198 m)
DS3, 45 Mbps	Coaxial cable	450 ft (137 m)
E3, 34 Mbps	Coaxial cable	1299 ft (396 m)
CDS3, 45 Mbps	Coaxial cable	450 ft (137 m)
8-port Gigabit Ethernet	Multimode or single-mode fiber	1640 ft (500 m) or 16404 ft (5 km)
2-port Gigabit Ethernet	Multimode or single-mode fiber	1640 ft (500 m) or 16404 ft (5 km)
2-port enhanced Gigabit Ethernet	Multimode or single-mode fiber	1640 ft (500 m) or 16404 ft (5 km)
16-port 10/100BASE-T Ethernet	UTP cable	328 ft (100 m) with 4 or fewer separate cable segments on the path
16-port 100BASE-FX Ethernet	Multimode fiber	1640 ft (500 m)
1-port ATM OC-3c uplink	Multimode or single-mode fiber	1640 ft (500 m) or 16404 ft (5 km)
1-port ATM OC-12c uplink	Multimode or single-mode fiber	1640 ft (500 m) or 16404 ft (5 km)
1-port Packet-over-SONET OC-12c uplink	Single-mode fiber	16404 ft (5 km)
8-port 10/100BASE-T Ethernet	UTP cable	328 ft (100 m) with 4 or fewer separate cable segments on the path
8-port 100BASE-FX Ethernet	50/125-micron and 62.5/125-micron multimode fiber	6562 ft (2 km)
1-port Gigabit Ethernet	Multimode fiber	1640 ft (500 m)

¹ If attaching a short cable to this port adapter or interface module, you must add 10 dB of attenuation to the cable or the transmitter might overdrive the receiver and introduce data errors.
²AWG = American Wire Gauge
³RJ = registered jack

GBIC Cable Distances and Modal Bandwidths

A GBIC has two pinouts: receive and transmit. The connectors are multimode fiber or single-mode fiber. Table A-6 lists the cable distances and modal bandwidth for GBICs.

Table A-6: GBIC Cable Distances and Modal Bandwidths

GBIC

Wavelength (nm¹)

Fiber Type

Core Size (microns)

Modal Bandwidth (MHz²-km)

Cable Distance

SX³,⁴

850

MMF

SMF

62.5

50.0

160

200

400

500

722 ft (200 m)

902 ft (275 m)

1620 ft (500 m)

1804 ft (550 m)

LX/LH⁵

1300

MMF

SMF⁶ (LX/LH)

62.5

50.0

9/10

500

400

5000

—

1804 ft (550 m)

32,810 ft (10 km)

ZX⁷

1550

SMF

Not conditional

—

70 to 100 km

¹nm = nanometers
²MHz-km = Signal bandwidth in MHz transmitted over a distance of 1 km
³SX = short wavelength
⁴MMF = multimode fiber
⁵LX/LH = long wavelength/long haul
⁶SMF = single-mode fiber
⁷ZX = extended distance

Fiber-Optic Power Levels

Table A-7 lists fiber-optic power levels for port adapters and interface modules used in ATM and Layer 3 systems. To attach long reach port adapters or interface modules using single-mode fiber, measure the power level of the transmitter and adjust it by using optical attenuators.

Caution Add a 10 dB attenuator at the interface to adjust the power level, or the transmitter overdrives the receiver and introduces data errors.

Table A-7: Fiber-Optic Power Levels

Port	Output Center Wavelength	Transmit	Receive
OC-3c SM	1261 to 1360 nm¹	Minimum: -15.0 dBm² Maximum: -8.0 dBm	Minimum: -27.0 dBm Maximum: -8.0 dBm
OC-3c SM long reach	1281 to 1380 nm	Minimum: -5.0 dBm Maximum: 0.0 dBm	Minimum: -34.0 dBm Maximum: -10.0 dBm
OC-3c MM	1270 to 1380 nm	Minimum: -20.0 dBm Maximum: -14.0 dBm	Minimum: -27.0 dBm Maximum: -14.0 dBm
OC-12c SM intermediate reach	1293 to 1334 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -3.0 dBm
OC-12c SM extended reach	1274 to 1356 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
OC-12c MM	1270 to 1380 nm	Minimum: -20.0 dBm Maximum: -14.0 dBm	Minimum: -26.0 dBm Maximum: -14.0 dBm
OC-12c SM long reach	1280 to 1335 nm	Minimum: -3.0 dBm Maximum: 2.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
OC-48c SM intermediate reach	1260 to 1360 nm	Minimum: -5.0 dBm Maximum: 0.0 dBm	Minimum: -18.0 dBm Maximum: 0.0 dBm
OC-48c SM long reach	1500 to 1580 nm	Minimum: -2.0 Maximum: 3.0 dBm	Minimum: -28.0 dBm Maximum:- 9.0 dBm
8-port Gigabit Ethernet	1261 to 1360 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
2-port Gigabit Ethernet	1261 to 1360 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
2-port enhanced Gigabit Ethernet	1261 to 1360 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
8-port 100BASE-FX	1261 to 1360 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm
1-port Gigabit Ethernet	1261 to 1360 nm	Minimum: -15.0 dBm Maximum: -8.0 dBm	Minimum: -28.0 dBm Maximum: -8.0 dBm

¹nm = nanometers
²dBm = decibels per milliwatt