During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Step 1 If you do not plan to immediately reinstall the supervisor engine you are removing, disconnect any network interface cables attached to the uplink ports.
Step 2 Use a screwdriver to loosen the captive installation screws at the left and right sides of the module.
Step 3 Grasp the left and right ejector levers; simultaneously pull the left lever to the left and the right lever to the right to release the module from the backplane connector.
Step 4 As you pull the module out of the slot, place one of your hands under the carrier to support it. Avoid touching the module itself.
Step 5 Carefully pull the module straight out of the slot, keeping one hand under the carrier to guide it. Keep the module at a 90-degree orientation to the backplane (horizontal to
the floor).
Step 6 Place the removed module on an antistatic mat or antistatic foam.
Note When you remove and replace the redundant supervisor engine, the system provides status
messages on the console screen. The messages are for information only. Enter the show system and
show module commands to view specific information. For additional information, refer to the
Software Configuration Guide and Command Reference for your switch.
Removing and Replacing the SIMM
The SIMM is fastened to the Supervisor Engine II motherboard. Once you remove the supervisor engine from the Catalyst 5000 series switch, you can remove and replace the SIMM.
Always use an ESD wrist strap when handling modules or coming into contact with internal components.
Figure 2 Supervisor Engine II with Installed SIMMs
To remove and replace the SIMM, refer to Figure 3 and perform the following steps:
Handle the SIMM by its edges only; avoid touching the memory module, pins, or traces (the metal fingers along the connector edge of the SIMM). SIMMs are sensitive components that are susceptible to ESD damage, and can be shorted by mishandling.
Step 1 To remove a SIMM from its socket, pull the locking spring clips on both sides outward and tilt the SIMM free of the clips. Be careful not to break the clips on the SIMM connector.
Step 2 Hold the SIMM by the edges and gently lift and remove it, placing it on an antistatic mat or foam.
Step 3 Remove the replacement 32-MB SIMM from its package, holding it by its edges, and carefully insert it into the connector so that it clicks into place.
Figure 3 Installing the 32-MB SIMM Card
Removing and Replacing the Supervisor Engine II NMP and MCP Boot ROMs
To upgrade the NMP and MCP boot ROMs in the Supervisor Engine II, follow these steps:
Always use an ESD wrist strap when handling modules or coming into contact with internal components.
Step 1 If you have not already done so, remove the Supervisor Engine II by following the instructions in the "Removing the Supervisor Engine" section.
Step 2 Locate the NMP boot ROM on the Supervisor Engine II.
On the 100BaseTX Supervisor Engine II (WS-X5509), the NMP boot ROM is located in socket U145 of the motherboard (see Figure 4).
On the 100BaseFX single-mode (WS-X5505) or multimode (WS-X5506) fiber Supervisor Engine II, the NMP boot ROM is located in socket U146 of the motherboard (see Figure 4).
Note The NMP boot ROM socket is physically in the same location on all Supervisor
Engine IIs; only the socket number is different.
Figure 4 Supervisor Engine II NMP Boot ROM Location
Step 3 To extract the NMP boot ROM from the motherboard, slide the tips of the PLCC extractor tool into the socket extraction slots until the angled tips are beneath the boot ROM device (see Figure 5).
Holding the tool as shown in Figure 5, remove the chip from the socket by squeezing the handles of the extraction tool evenly and pulling the boot ROM device straight upward until it is released from the socket. Use care not to damage the boot ROM device or
the socket.
Figure 5 Supervisor Engine II NMP Boot ROM Extraction
Step 4 Place the extracted NMP boot ROM in an antistatic bag.
Step 5 Carefully remove the new software release 5.1(2) NMP boot ROM from its packaging.
Note The NMP boot ROM chip has the Cisco part number 17-3419-10 etched on the top
of the chip. Ensure that you are working with the NMP boot ROM and not the MCP
boot ROM.
Step 6 Insert the NMP boot ROM in socket U145 or U146 on the motherboard. Be sure to orient the boot ROM so that the notched corner of the chip matches the notched corner of the socket (see Figure 6). Press the boot ROM into place evenly and firmly until it is completely seated in the socket.
Make sure you orient the chip to the socket correctly. If the chip is oriented to the socket improperly, you can damage both the chip and the socket.
Figure 6 Supervisor Engine II Boot ROM Insertion
Step 7 Locate the MCP boot ROM on the Supervisor Engine II. The MCP boot ROM is located in socket U56 of the motherboard (see Figure 4).
Step 8 To extract the MCP boot ROM from the motherboard, slide the tips of the PLCC extractor tool into the socket extraction slots until the angled tips are beneath the boot ROM device (see Figure 5).
Holding the tool as shown in Figure 5, remove the chip from the socket by squeezing the handles of the extraction tool evenly and pulling the boot ROM device straight upward until it is released from the socket. Use care not to damage the boot ROM or the socket.
Step 9 Place the extracted MCP boot ROM in an antistatic bag.
Step 10 Carefully remove the new software release 4.3(1) MCP boot ROM from its packaging.
Note The MCP boot ROM chip has the Cisco part number 17-3420-09 etched on the top
of the chip. Ensure that you are working with the MCP boot ROM and not the NMP boot
ROM.
Step 11 Insert the MCP boot ROM in socket U56 on the motherboard. Be sure to orient the boot ROM so that the notched corner of the chip matches the notched corner of the socket (see Figure 6). Press the boot ROM into place evenly and firmly until it is completely seated in the socket.
Step 12 Install the supervisor engine in the Catalyst 5000 series switch (see the "Replacing the Supervisor Engine" section for installation instructions) and boot the switch.
Step 13 When the system comes online, use the show version command to verify that the supervisor engine Fw (NMP) version level is software release 5.1(2) and that the Fw1 (MCP) version level is software release 4.3(1):
Console> (enable)
show version 1
Mod Port Model Serial # Versions
--- ---- ---------- --------- ----------------------------------------
1 2 WS-X5509 007486003 Hw : 2.3
Replacing the Supervisor Engine
Note The ejector levers on the supervisor engine and switching modules align and seat the module
connectors in the backplane (see Figure
1). If you fail to use the ejector levers to insert the module, you can disrupt the order in which the
pins contact the backplane. The ejector levers must be pulled out as you slide the module in. Follow
the installation instructions carefully. Detailed instructions for removing and installing switching
modules are described in the Catalyst 5000 Series Module Installation Guide.
To replace the supervisor engine, follow Steps 1 through 6 in the "Removing the Supervisor Engine" section in reverse order. Note that the supervisor engine must go in a specific slot:
- Catalyst 5002 switch—slot 1
- Catalyst 5000 switch—slot 1
- Catalyst 5505, Catalyst 5509, and Catalyst 5500 switches—slot 1 (if a second, redundant supervisor is installed, install it in slot 2)
Standards Compliance Specifications
Catalyst 5000 series modules, when intalled in a system, comply with the standards listed in Table 1:
Table 1 Standards Compliance Specifications
| Specification
|
Description
|
|
Compliance
|
CE1 Marking
|
|
Safety
|
UL2 1950, CSA3-C22.2 No. 950, EN460950, IEC5 950, TS6 001, AS/NZS7 3260
|
EMI8
|
FCC9 Class A (47 CFR10, Part 15), ICES11-003 Class A, EN55022 Class A, CISPR22 Class A, AS/NZS 3548 Class A, and VCCI12 Class A with UTP13
EN55022 Class B, CISPR22 Class B, AS/NZS 3548 Class B, and VCCI Class B (Japan) with FTP14 cables
|
| CE = European Compliance
UL = Underwriters Laboratory
CSA = Canadian Standards Association
EN = European Norm
IEC = International Electrotechnical Commission
TS = Technical Specification
AS/NZS = Standards Australia/Standards New Zealand
EMI = electromagnetic interference
FCC = Federal Communications Commission
CFR = Code of Federal Regulations
ICES = Interference-Causing Equipment Standard
VCCI = Voluntary Control Council for Information Technology Equipment
unshielded twisted-pair
foil twisted-pair
|
FCC Class A Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
- Turn the television or radio antenna until the interference stops.
- Move the equipment to one side or the other of the television or radio.
- Move the equipment farther away from the television or radio.
- Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems could void the FCC approval and negate your authority to operate this product.
Related Documentation
For more detailed installation and configuration information, refer to the following publications:
- Catalyst 5000 Series Installation Guide
- Catalyst 5000 Series Supervisor Engine Installation Guide
- Software Configuration Guide—Catalyst 5000 Series, Catalyst 4000 Series, Catalyst 2948G Series, Catalyst 2926G Series
- Command Reference—Catalyst 5000 Series, Catalyst 4000 Series, Catalyst 2948G Series, Catalyst 2926G Series
Cisco Connection Online
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
Note If you are a network administrator and need personal technical assistance with a Cisco
product that is under warranty or covered by a maintenance contract, contact Cisco's Technical
Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general
information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387,
408 526-7208, or cs-rep@cisco.com.
Documentation CD-ROM
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
|
