This document provides the cabling specifications for the Cisco 1603-R Ethernet/ISDN-BRI Modular router.
There are no specific requirements for this document.
The information in this document is based on the hardware version:
Cisco 1603-R Router
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
For more information on document conventions, see the Cisco Technical Tips Conventions.
The Cisco 1603-R router has one Ethernet interface, one Integrated Services Digital Network (ISDN) interface, and one Basic Rate Interface (BRI) S/T WAN interface card (WIC) slot.
The cabling details for the Cisco 1603-R are as follows:
The console cable is an RJ-45, the CAB-1600-CON=.
The AUI adapter cable is a CAB-3CE18=.
The ISDN BRI requires an RJ-45 straight through cable. Individual cable options are: CAB-S/T-RJ45= Orange Color Cable for ISDN BRI S/T, RJ-45, 6 ft.
The table below shows the port pinouts for the IDSN BRI S/T (RJ-45).
1Pins 1, 2, 7, and 8 are not used.
2TE refers to terminal equipment Layer 1 aspects of TE1, TA, and NT functional groups. This applies to the Cisco 1603 and the ISDN BRI S/T WAN interface card.
3NT refers to network terminating Layer 1 aspects of NT1 and NT2 functional groups. This applies to the Cisco 1604 ISDN S/T port.
The table below provides the cable specifications of the ISDN BRI cable.
|Specification||High-capacity Cable||Low-capacity Cable|
|Resistance (at 96 kHz)||160 ohms/km||160 ohms/km|
|Capacity (at 1 kHz)||120 nF1/km||30 nF/km|
|Impedance (96 kHz)||75 ohms||150 ohms`|
|Wire diameter||0.024" (0.6 mm)||0.024" (0.6 mm)|
|Distance limitation||32.8' (10 m)||32.8' (10 m)|
1 nF = nanoFarad.
WAN interface cards supported on the Cisco 1603-R consist of the following:
WIC-1T: 1-port serial, async and sync (T1/E1)
WIC-1DSU-56K4: 1 serial with integrated 56/64 Kbps 4-wire DSU/CSU
WIC-1DSU-T1: 1 serial with integrated T1/Fractional T1 DSU/CSU
WIC-1B-S/T-LL: ISDN BRI Leased Line S/T WAN Interface
The table below shows the front panel LED functions for the Cisco 1601 and Cisco 1602 routers.
|SYSTEM PWR||Green||The router is on, and DC power is being supplied.|
|SYSTEM OK||Green||The router has successfully booted. Blinks during the boot cycle.|
|LAN ACT||Green||Data is being sent to or received from the local Ethernet LAN.|
|LAN COL||Yellow||Flashing indicates packet collisions on the local Ethernet LAN.|
|BRI 0 B1||Green||
|BRI 0 B2||Green||
|WIC CD||Green||Active connection on the WAN interface card serial port.|
|WIC ACT||Green||Data is being sent over the WAN interface card serial port.|
The table below explains the rear panel LED functions.
|LNK (next to ETHERNETØ 10BASET)||Green||Indicates 10BaseT link integrity. This LED is not on when connected to an Ethernet network through the AUI port. The Cisco 1605 has two LNK LEDs, one for each Ethernet 10BaseT port.|
|OK (next to FLASH PC CARD slot)||Green||The Flash PC card is correctly installed.|
|RDY||Green||A serial port cable connection has been made to a modem or DSU/CSU.|
|LOOPBACK||Yellow||The DSU/CSU is in DSU or CSU loopback mode.|
|ALARM||Yellow||An alarm condition exists on the DSU/CSU port.|
|CARRIER||Green||Indicates line synchronization or connection on the DSU/CSU port.|
|OK (next to ISDN BRIØ S/T port)||Green||A physical connection has been established with the ISDN central office switch.|
|NT1||Green||A physical connection has been established from the router internal NT1 to the ISDN central office switch.|
|OK (next to ISDN PHONE port)||Green||The device connected to the router ISDN S/T port has established a physical connection with the ISDN central office switch.|
|LNK (next to ETHERNET1 10BASET)||Green||Indicates 10BaseT link integrity for the Ethernet 1 port.|
|OK (next to WIC slot)||Green||The WAN interface card is correctly installed in the router.|
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.