This document provides standard break key sequence combinations for the most common operating systems, and some tips on how to troubleshoot problems.
The Electronic Industries Association RS-232 logic level uses +3 to +25 volts to signify a Space (Logic 0) and -3 to -25 volts for a Mark (logic 1). A break signal is when the data line remains in the space condition for a specified duration, usually 100 ms to ½ second. All characters begin with a start bit and end with a stop bit (and also a parity bit or two). The level condition of the start and stop bits is always opposite. So, no character combination can look like the break signal. A break signal enables you to access a ROM Monitor on Cisco IOS® devices when a password recovery is necessary.
There are no specific requirements for this document.
This document is not restricted to specific software and hardware versions.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Refer to Cisco Technical Tips Conventions for more information on document conventions.
|Software||Platform||Operating System||Try This|
|Hyperterminal||IBM Compatible||Windows XP||Ctrl-Break|
|Hyperterminal||IBM Compatible||Windows 2000||Ctrl-Break|
|Hyperterminal||IBM Compatible||Windows 98||Ctrl-Break|
|Hyperterminal (version 595160)||IBM Compatible||Windows 95||Ctrl-F6-Break|
|MicroPhone Pro||IBM Compatible||Windows||Ctrl-Break|
|Minicom||IBM Compatible||Linux||Ctrl-a f|
|ProComm Plus||IBM Compatible||DOS or Windows||Alt-b|
|Telnet||N/A||N/A||Ctrl-], then type send brk|
|Telnet to Cisco||IBM Compatible||N/A||Ctrl-]|
|Tip||Sun Workstation||UNIX||Ctrl-], then Break or Ctrl-c|
|VT 100 Emulation||Data General||N/A||F16|
|Windows NT||IBM Compatible||Windows||Break-F5|
|Shift-6 Shift-4 Shift-b (^$B)|
|N/A||Break-Out Box||N/A||Connect pin 2 (X-mit) to +V for half a second|
|Cisco to aux port||N/A||Control-Shft-6, then b|
Problems that you encounter during password recovery often occur because you are not sure about what the break key sequence is for the (non-Cisco) software you use. For software not listed in the table, and for additional information, refer to the documentation of the individual software packages.
The auxiliary (AUX) port is not active during the boot sequence of a router. Therefore, it is no use if you send a break through the AUX port. You need to have connection to the console port, and have these settings:
9600 baud rate
8 data bits
1 stop bit
No flow control
Some versions of Windows NT have hyperterminal software that cannot send the correct break key signal. Refer to http://www.hilgraeve.com/hyperterminal.html for more information and for an upgrade of the hyperterminal software.
In some cases, the break sequence might not get transmitted properly when using a USB/Serial converter cable. In such cases, use a keyboard with a different connector port (for example, a PS/2).
Break key sequence simulation is useful if your terminal emulator does not support the break key, or if a bug does not allow your terminal emulator to send the correct signal.
Note: The hyperterminal under Windows NT had this behavior in the past.
Complete these steps to simulate a break key sequence:
Connect to the router with these terminal settings:
1200 baud rate
8 data bits
1 stop bit
No flow control
You no longer see any output on your screen, and this is normal.
Power cycle (switch off and then on) the router and press the SPACEBAR for 10-15 seconds in order to generate a signal similar to the break sequence.
Disconnect your terminal, and reconnect with a 9600 baud rate. You enter the ROM Monitor mode.
If all these methods fail to properly send a break, retry the procedures from a different terminal or PC platform.
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.