Guest

Cisco ONS 15300 Series

Cisco ONS 15302 Quick Installation Guide, Release 2.0

 Feedback

Table Of Contents

Cisco ONS 15302 Quick Installation Guide

Obtaining Documentation

Cisco.com

Documentation DVD

Ordering Documentation

Documentation Feedback

Cisco Product Security Overview

Reporting Security Problems in Cisco Products

Obtaining Technical Assistance

Cisco Technical Support Website

Submitting a Service Request

Definitions of Service Request Severity

Obtaining Additional Publications and Information

Quick Overview

Before Starting

Translated Warnings

DC Power Disconnection Warning

Main Disconnecting Device

Laser Radiation Warning

Unterminated Fiber Warning

Class 1 Laser Product Warning

Installation Materials for ONS 15302

Installing the ONS 15302

Installing the ONS 15302 in a 19-in. (485-mm) Rack

Installation in Restricted Access Locations

Installing 48-V Power and Ground to the ONS 15302

Install External Ground for 230 V Supply to the ONS 15302

Installing 230-V Power to the ONS 15302

Installing Fiber Patch Cords on the ONS 15302

Routing Fiber Patch Cords

Installing Electrical Cables to the ONS 15302

Routing Electrical Cables

Installation Checklist for ONS 15302

ONSCLI—ONS 15302 Command Line Interface

Introduction to ONSCLI

Accessing ONSCLI

Syntax Rules

Basic Command Syntax

Initial Configuration

Factory Preconfiguration

Important Commands


Quick Start Guide

Cisco ONS 15302 Quick Installation Guide


Release 2.0

January 2005

1 Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Documentation DVD

Cisco documentation and additional literature are available in a Documentation DVD package, which may have shipped with your product. The Documentation DVD is updated regularly and may be more current than printed documentation. The Documentation DVD package is available as a single unit.

Registered Cisco.com users (Cisco direct customers) can order a Cisco Documentation DVD (product number DOC-DOCDVD=) from the Ordering tool or Cisco Marketplace.

Cisco Ordering tool:

http://www.cisco.com/en/US/partner/ordering/

Cisco Marketplace:

http://www.cisco.com/go/marketplace/

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:

http://www.cisco.com/en/US/partner/ordering/

Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 1 800 553-NETS (6387).

2 Documentation Feedback

You can send comments about technical documentation to bug-doc@cisco.com.

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

We appreciate your comments.

3 Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you can perform these tasks:

Report security vulnerabilities in Cisco products.

Obtain assistance with security incidents that involve Cisco products.

Register to receive security information from Cisco.

A current list of security advisories and notices for Cisco products is available at this URL:

http://www.cisco.com/go/psirt

If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you might have identified a vulnerability in a Cisco product, contact PSIRT:

Emergencies — security-alert@cisco.com

Nonemergencies — psirt@cisco.com


Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive information that you send to Cisco. PSIRT can work from encrypted information that is compatible with PGP versions 2.x through 8.x .

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one that has the most recent creation date in this public key server list:

http://pgp.mit.edu:11371/pks/lookup?search=psirt%40cisco.com&op=index&exact=on


In an emergency, you can also reach PSIRT by telephone:

1 877 228-7302

1 408 525-6532

4 Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do


Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.


Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—Your network is "down," or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

5 Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

http://www.cisco.com/packet

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html

6 Quick Overview

Figure 1 ONS 15302 Functional Overview

The main R1.0 to R2.0 enhancement is the introduction of GFP/LCAS, which is a Ethernet framing standard to transport Ethernet packets in virtual containers through a SDH network. Additionally this edition introduces a new option for management connectivity, which will simplify design and configuration of a network supplied by Cisco. All features in this release is aligned with the new release of ONS 15305.

The ONS 15302 is an Integrated Access Device mainly intended for use in fibre optic networks, but can also be supplied as a hardware option with support for electrical STM-1. The ONS 15302 combine IP- and TDM-traffic, by running IP- along with TDM-channels inside an SDH STM-1 frame structure that can be easily carried across the network. The bandwidth of the IP-channel is configurable up to 100 Mb/s true "wire-speed". The IP part of the ONS 15302 R2.0 consists of a L2/L3 switch.

Each tributary interface (E1) is mapped into a VC-12 container while the WAN traffic can be transported via either nxVC-3 or nxVC12.

The ONS 15302 have room for a plug-in module, which adds more WAN-ports to achieve multiple connections with differentiated bandwidth per customer and/or service.

The ONS 15302 management solution is based on an embedded SNMP agent and a SNMP Craft utility (Cisco EdgeCraft) is supplied with the deliveries of ONS 15302. Minimum required to operate and configure the ONS 15302 is a simple VT100 command line interface (ONSCLI) for direct communication with the embedded SNMP agent.

7 Before Starting

This guide provides basic instructions for installing the Cisco ONS 15302 system. It contains two different parts:

Installing the ONS 15302

Configure the ONS 15302

Use this guide as a general reference when performing an installation.

For detailed installation instructions, refer to the most recent Cisco ONS 15302 Installation and Operations Guide (Release 2.0).


Caution Always use the supplied ESD wristband when working with an ONS 15302. Plug the wristband cable into the ESD jack of the rack assembly and ensure the rack assembly is properly grounded.

8 Translated Warnings

DC Power Disconnection Warning

 

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Waarschuwing

Voordat u een van de onderstaande procedures uitvoert, dient u te controleren of de stroom naar het gelijkstroom circuit uitgeschakeld is.

Varoitus

Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien toimenpiteiden suorittamista.

Attention

Avant de pratiquer l'une quelconque des procédures ci-dessous, vérifier que le circuit en courant continu n'est plus sous tension.

Warnung

Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die Gleichstromschaltung keinen Strom erhält.

Figyelem!

Mielõtt a következõ eljárások bármelyikét végrehajtaná, feltétlenül szakítsa meg az egyenáramú áramkör tápellátását.

Avvertenza

Prima di svolgere una qualsiasi delle procedure seguenti, verificare che il circuito CC non sia alimentato.

Advarsel

Før noen av disse prosedyrene utføres, kontroller at strømmen er frakoblet likestrømkretsen.

Aviso

Antes de executar um dos seguintes procedimentos, certifique-se que desligou a fonte de alimentação de energia do circuito de corrente contínua.

¡Advertencia!

Antes de proceder con los siguientes pasos, comprobar que la alimentación del circuito de corriente continua (CC) esté cortada (OFF).

Varning!

Innan du utför någon av följande procedurer måste du kontrollera att strömförsörjningen till likströmskretsen är bruten.


Main Disconnecting Device

 

Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.

Waarschuwing

De combinatie van de stekker en het elektrisch contactpunt moet te allen tijde toegankelijk zijn omdat deze het hoofdmechanisme vormt voor verbreking van de aansluiting.

Varoitus

Pistoke/liitinkohta toimii pääkatkaisumekanismina. Pääsy siihen on pidettävä aina esteettömänä.

Attention

La combinaison de prise de courant doit être accessible à tout moment parce qu'elle fait office de système principal de déconnexion.

Warnung

Der Netzkabelanschluß am Gerät muß jederzeit zugänglich sein, weil er als primäre Ausschaltvorrichtung dient.

Figyelem!

A dugaszolóaljzat és a dugasz együttesének mindig hozzáférhetõnek kell lennie, mivel ez szolgál fõmegszakítóként.

Avvertenza

Il gruppo spina-presa deve essere sempre accessibile, poiché viene utilizzato come dispositivo di scollegamento principale.

Advarsel

Kombinasjonen støpsel/uttak må alltid være tilgjengelig ettersom den fungerer som hovedfrakoplingsenhet.

Aviso

A combinação ficha-tomada deverá ser sempre acessível, porque funciona como interruptor principal.

¡Advertencia!

El conjunto de clavija y toma ha de encontrarse siempre accesible ya que hace las veces de dispositivo de desconexión principal.

Varning!

Man måste alltid kunna komma åt stickproppen i uttaget, eftersom denna koppling utgör den huvudsakliga frånkopplingsanordningen.


Laser Radiation Warning

 

Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.

Waarschuwing

Losgekoppelde of losgeraakte glasvezels of aansluitingen kunnen onzichtbare laserstraling produceren. Kijk niet rechtstreeks in de straling en gebruik geen optische instrumenten rond deze glasvezels of aansluitingen.

Varoitus

Irrotetuista kuiduista tai liittimistä voi tulla näkymätöntä lasersäteilyä. Älä tuijota säteitä tai katso niitä suoraan optisilla välineillä.

Attention

Les fibres ou connecteurs débranchés risquent d'émettre des rayonnements laser invisibles à l'œil. Ne regardez jamais directement les faisceaux laser à l'œil nu, ni d'ailleurs avec des instruments optiques.

Warnung

Unterbrochene Fasern oder Steckerverbindungen können unsichtbare Laserstrahlung abgeben. Blicken Sie weder mit bloßem Auge noch mit optischen Instrumenten direkt in Laserstrahlen.

Figyelem!

A nem csatlakoztatott üvegszálak és csatlakozók láthatatlan lézersugárzást bocsáthatnak ki. Ne nézzen bele a sugárba, és ne nézze közvetlenül, optikai berendezések segítségével!

Avvertenza

Le fibre ottiche ed i relativi connettori possono emettere radiazioni laser. I fasci di luce non devono mai essere osservati direttamente o attraverso strumenti ottici.

Advarsel

Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte inn i strålene eller se på dem direkte gjennom et optisk instrument.

Aviso

Radiação laser invisível pode ser emitida de conectores ou fibras desconectadas. Não olhe diretamente para os feixes ou com instrumentos ópticos.

¡Advertencia!

Es posible que las fibras desconectadas emitan radiación láser invisible. No fije la vista en los rayos ni examine éstos con instrumentos ópticos.

Varning!

Osynlig laserstrålning kan avges från frånkopplade fibrer eller kontaktdon. Rikta inte blicken in i strålar och titta aldrig direkt på dem med hjälp av optiska instrument.


Unterminated Fiber Warning

 

Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.

Waarschuwing

Er kunnen onzichtbare laserstralen worden uitgezonden vanuit het uiteinde van de onafgebroken vezelkabel of connector. Niet in de straal kijken of deze rechtstreeks bekijken met optische instrumenten. Als u de laseruitvoer met bepaalde optische instrumenten bekijkt (zoals bijv. een oogloep, vergrootgras of microscoop) binnen een afstand van 100 mm kan dit gevaar voor uw ogen opleveren.

Varoitus

Päättämättömän kuitukaapelin tai -liittimen päästä voi tulla näkymätöntä lasersäteilyä. Älä tuijota sädettä tai katso sitä suoraan optisilla välineillä. Lasersäteen katsominen tietyillä optisilla välineillä (esim. suurennuslasilla tai mikroskoopilla) 10 cm:n päästä tai sitä lähempää voi olla vaarallista silmille.

Attention

Des émissions de radiations laser invisibles peuvent se produire à l'extrémité d'un câble en fibre ou d'un raccord sans terminaison. Ne pas fixer du regard le rayon ou l'observer directement avec des instruments optiques. L'observation du laser à l'aide certains instruments optiques (loupes et microscopes) à une distance inférieure à 100 mm peut poser des risques pour les yeux.

Warnung

Eine unsichtbare Laserstrahlung kann vom Ende des nicht angeschlossenen Glasfaserkabels oder Steckers ausgestrahlt werden. Nicht in den Laserstrahl schauen oder diesen mit einem optischen Instrument direkt ansehen. Ein Betrachten des Laserstrahls mit bestimmten optischen Instrumenten, wie z.B. Augenlupen, Vergrößerungsgläsern und Mikroskopen innerhalb eines Abstands von 100 mm kann für das Auge gefährlich sein.

Figyelem!

A lezáratlan optikai kábelek és a csatlakozók láthatatlan lézerfényt bocsáthatnak ki. Ne nézzen bele a sugárba, és ne nézze közvetlenül, optikai berendezések segítségével! Ha a kibocsátott lézert 100 mm-esnél kisebb távolságból nézi bizonyos optikai eszközökkel (például nagyítóval vagy mikroszkóppal), látáskárosodást szenvedhet.

Avvertenza

L'estremità del connettore o del cavo ottico senza terminazione può emettere radiazioni laser invisibili. Non fissare il raggio od osservarlo in modo diretto con strumenti ottici. L'osservazione del fascio laser con determinati strumenti ottici (come lupette, lenti di ingrandimento o microscopi) entro una distanza di 100 mm può provocare danni agli occhi.

Advarsel

Usynlig laserstråling kan emittere fra enden av den ikke-terminerte fiberkabelen eller koblingen. Ikke se inn i strålen og se heller ikke direkte på strålen med optiske instrumenter. Observering av laserutgang med visse optiske instrumenter (for eksempel øyelupe, forstørrelsesglass eller mikroskoper) innenfor en avstand på 100 mm kan være farlig for øynene.

Aviso

Radiação laser invisível pode ser emitida pela ponta de um conector ou cabo de fibra não terminado. Não olhe fixa ou diretamente para o feixe ou com instrumentos ópticos. Visualizar a emissão do laser com certos instrumentos ópticos (por exemplo, lupas, lentes de aumento ou microscópios) a uma distância de 100 mm pode causar riscos à visão.

¡Advertencia!

El extremo de un cable o conector de fibra sin terminación puede emitir radiación láser invisible. No se acerque al radio de acción ni lo mire directamente con instrumentos ópticos. La exposición del ojo a una salida de láser con determinados instrumentos ópticos (por ejemplo, lupas y microscopios) a una distancia de 100 mm puede comportar lesiones oculares.

Varning!  

Osynlig laserstrålning kan komma från änden på en oavslutad fiberkabel eller -anslutning. Titta inte rakt in i strålen eller direkt på den med optiska instrument. Att titta på laserstrålen med vissa optiska instrument (t.ex. lupper, förstoringsglas och mikroskop) från ett avstånd på 100 mm kan skada ögonen.


Class 1 Laser Product Warning

 

Warning Class 1 laser product.

Waarschuwing

Klasse-1 laser produkt.

Varoitus

Luokan 1 lasertuote.

Attention

Produit laser de classe 1.

Warnung

Laserprodukt der Klasse 1.

Figyelem!

Class 1 besorolású lézeres termék.

Avvertenza

Prodotto laser di Classe 1.

Advarsel

Laserprodukt av klasse 1.

Aviso

Produto laser de classe 1.

¡Advertencia!

Producto láser Clase I.

Varning!

Laserprodukt av klass 1.

 


9 Installation Materials for ONS 15302

Several items are needed to complete the installation of the ONS 15302. Some of these items are supplied by Cisco and some need to be supplied by the user. The following are the Cisco-supplied materials that are include in the 15302-SHIPKIT= (74-3173-01). The number in parentheses is the quantity of each included item.

Bumper, 12mm diameter, 7 x 3.5 mm for table placing (4)

48-V 4-Pin power connector (1)

Brackets L/R 19" (2)

Brackets L/R ETSI (23") (2)

ONSCLI cable (1)

Blade terminal with screw and blade jack (1)

ESD wrist strap (1)

230-V power cable (1)

Registration card (1)

Warranty card (1)

The following materials, tools, and equipment are recommended but are not supplied with the ONS 15302:

Fuse panel

Power cable (from fuse to power connector), #18 AWG (0.75 mm2) up to #16 AWG (1.5 mm2) with four rigid wire

Yellow green flexible ground cable # 16 AWG (1.25 mm2) up to #14 AWG (2.50 mm2)

Single-mode cable with SC connectors

Fiber connector inspection instruments (Cisco recommends Video Microscopes)

Cletop cleaning cassette (type A for SC connectors)

Caps for optical connectors (SC)

Labels

#1 Phillips screwdriver

#3 Phillips screwdriver

2.5-mm Allen key

4 screws, M6 (#12-24 x 3/4 pan head phillips) and nuts

Voltmeter

Power meter (for use with fiber optics only)

Bit error rate (BER) tester

10 Installing the ONS 15302

To install the ONS 15302, complete the following procedures:

1. Installing the ONS 15302 in a 19-in. (485-mm) Rack

2. Installation in Restricted Access Locations

3. Installing 48-V Power and Ground to the ONS 15302

4. Install External Ground for 230 V Supply to the ONS 15302

5. Installing 230-V Power to the ONS 15302

6. Installing Fiber Patch Cords on the ONS 15302

7. Routing Fiber Patch Cords

8. Installing Electrical Cables to the ONS 15302

9. Routing Electrical Cables

Installing the ONS 15302 in a 19-in. (485-mm) Rack

The shelf assembly is allocated for installation in a 19-in. (485-mm) rack. The ONS 15302 is 17.5-in. (445-mm) wide by 9.4-in. (240-mm) deep by 1.7-in. (44-mm) high.


Step 1 Depending on access requirement, front or rear access, decide which side you want to use as the front side in the rack. Refer to Figure 2 and Figure 3.

Step 2 Remove the four phillips screws on the left and right side of the ONS 15302 and install the brackets with the longer phillips screws that are provided.

Step 3 Move the ONS 15302 to the desired rack position ( Figure 2 and Figure 3).

Step 4 Secure the ONS 15302 to the rack. Tighten the ONS 15302 with four screws ( Figure 2 and Figure 3).

Figure 2 Install the ONS 15302 with the Connector Array in Front in a 19-in. Rack

Figure 3 Install the ONS 15302 with the WAN Module in Front in a 19-in. Rack


Note You can also install the ONS 15302 in a ETSI 23.6-in. (600-mm) rack by using extension brackets to convert it. You need two 1-RU extension brackets to do this.



Installation in Restricted Access Locations

The ONS 15302 can be installed in a restricted access location (RAL) or outside of an RAL.

Definitions

Restricted Access Location

A restricted access location is a site location for equipment where both of the following paragraphs apply:

Access can only be gained by service persons or by users who have been trained on the restrictions and the precautions for this specific site.

Access is by means of at least one of the following, special tool, lock and key, or other means of security.

SELV Circuits

Safety Extra-Low Voltage (SELV) circuits are ports that have maximum DC working voltage level less than 60 V (42.4 VAC). In addition, the ports must not be connected to telecommunication networks as defined in EN 60950 (see CEI/ IEC 60950-1 2001-10, standard clause 1.2.13.8).

In practice, the electrical cables shall not exit the building. In addition, the electrical cables shall connect to equipment that meets one of the following requirements:

Installed in the RAL.

Does not have electrical cables that exit the building unless those ports are TNV (Telecommunication Networks Voltage) circuits.

Has a written consent (or in other evidence) that its connecting port towards the SELV circuit port is not a telecommunication network.

Telecommunication Network

A telecommunication network is a metallically terminated transmission medium intended for communication between equipment that might be located in separate buildings, excluding:

Main system for supply, transmission and distribution of electrical power, if used as a telecommunication transmission medium

Cable distribution system

SELV circuits connecting units of information technology equipment

TNV Circuit

A TNV circuit in the equipment to which the accessible area of contact is limited. A TNV circuit is so designed and protected that, under normal operating conditions and single fault conditions (see CEI/IEC 60950-1 2001-10, standard clause 1.4.14), the voltages do not exceed specified limit values.

Installation in Restricted Access Location

After installation in a RAL, such as in a telecommunications center, the ONS 15302 must be properly installed in a rack with brackets or in other ways properly connected to a safety ground. The ONS 15302 48-VDC power must not be powered from a source external to the RAL. The E1 interface used should be limited to SELV.

Installation Outside of a Restricted Access Location

After installation in a non-RAL location, the ONS 15302 48-V power and all communication ports used must be connected to SELV circuits, for example, a port on a personal computer or 10/100-Mbit Ethernet hub/router or other information technology (IT) equipment. The 48-VDC power must not exceed 60 VDC, and must be powered from a certified external power supply unit (PSU) or a battery unit (with no connection to -48 V telecommunications voltage).

The optical ports and 230-VAC power plug have no limitations regarding safety recommendations.

Installing 48-V Power and Ground to the ONS 15302

The power needs to be properly installed and grounded for operation of the ONS 15302. Figure 4 shows the location of the 48-V connector. Use the following procedure to install power and ground to the ONS 15302:


Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.



Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.


Figure 4 ONS 15302 Faceplate (Connector Array)


Step 1 Remove the A- and B-side fuses from the power distribution panel (PDP).

Step 2 Make sure that -48 VDC (tolerance -36 to -72 VDC) power is present.

Step 3 Press a slot screwdriver in the rectangular opening on top of the connector to open the inside contact ( Figure 5).

Step 4 Insert the wire in the contact and remove the screwdriver from the connector.

Step 5 To verify that the wire is properly fix in the unit, pull on the wire.

Step 6 Repeat Step 3 to Step 5 for the other three wires.

Step 7 Affix the four wires on the connector using the two tie wraps to ensure strain relief ( Figure 5).


Note Be sure that the power cable is connected and verify the correct polarity. Check if is properly fused (1.5-A recommended).



Note Note that the ONS 15302 power cannot be switched off with a separate power switch.


Figure 5 Fixing the Wire into the Connector


Install External Ground for 230 V Supply to the ONS 15302


Note This ground connection is only used when the system is powered with 230 VAC and the system is not installed in a rack.


The ONS 15302 should be grounded to the rack ground via the external ground connector.

The location of the ground connector on the ONS 15302 is shown in Figure 6.

Figure 6 Ground Connector Position on the ONS 15302


Step 1 Remove the Phillips screw from the ONS 15302 ( Figure 6).

Step 2 Fix the flat connector with the washer and the socket screw onto the ONS 15302 ( Figure 6).

Step 3 Insert the grounding cable in the flat cable plug and crimp the plug with a crimping tool ( Figure 7).

Step 4 Check whether the ground cable is fixed to the flat cable plug.

Step 5 Connect the flat cable plug to the flat connector.

Step 6 Route the ground cable securely to the local ground connector and connect it according to local site practice.

Figure 7 Connecting of the Ground Cable with a Crimp Tool


Installing 230-V Power to the ONS 15302

The ONS 15302 can also be used as a desk version. This means that it is possible to connect the ONS 15302 to a public power supply. Figure 4 shows the location of the 230-V connector.


Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.



Note Before installing power to the ONS 15302, be sure that you have the correct power supply recommendations (230 VAC 0.3 A 50Hz).



Note Note that the ONS 15302 power cannot be switched off with a separate power switch.



Step 1 Connect the power cable to the 230-V connector on the ONS 15302.

Step 2 Connect the power cable to the 230-V power supply.

Step 3 To avoid accidents, route the power cable safety through the location.

Installing Fiber Patch Cords on the ONS 15302

The ONS 15302 is available in two different versions: protected and unprotected. In unprotected mode, transmit and receive fibers from the fiber termination rack are connected to STM-1 port 1. In protected mode, transmit and receive fibers from the fiber termination rack are connected to STM-1 port 1 and port 2, ( Figure 4).


Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.



Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.



Warning Class 1 laser product.



Note Clean and inspect SC connectors prior to installation. Any dust particle or damaged connector will affect the optical transmission.


To avoid confusion in the future, label each end of the transmit and receive cables before installation. To install the fiber patch cords, gently push the SC connector into the connector.

For future use (in case of servicing) keep the dust caps in a clean location.


Routing Fiber Patch Cords

After connecting the fibers to and from the fiber termination rack, route the fibers through the rack. Wind the fibers to a loop with a diameter of approximately 3.15 in. (80-mm).

Installing Electrical Cables to the ONS 15302

The ONS 15302 has two different electrical connectors: one DS-9 connector for the alarm interface and 20 RJ-45 connectors for different functions, described in Table 1. The electrical ports on the ONS 15302 are shown in Figure 4.

To avoid confusion in the future, label each end of the cables before installation. To install the electrical cables, gently push the RJ-45 connector into the connector until it snaps in with a click. Screw in the screws from the connector of the alarm cable with a screwdriver.

Table 1 Recommended Cable Types for the ONS 15302

Port Name
Quantity
Recommended Cable Type
Used for

ALARM

1

UTP

External alarm management

LAN

4

UTP Category 5 for 100-Mbits/s (Mbps) Ethernet

LAN or WAN connections (10/100 Mbits/s [Mbps])

SYNC

1

UTP (The outer screen of the SYNC cable is always connected to ground [pin 6]).

Input and output synchronization

VT100 (CLI)

1

UTP (Category 1) supplied from Cisco

CLI connections (cable supplied by Cisco)

MNGT (Management)

1

UTP Category 5

Connection to a remote craft terminal

USER CH

1

UTP Category 1

User application

TRIB (Tributary)

12

STP

Tributary connections

STM-1

2 or 4

Single-mode fiber according to ITU-T G.652

Optical connections



Routing Electrical Cables

After connecting the cable to the ONS 15302, route the cable through the rack without damage it.

Installation Checklist for ONS 15302

The following list is an installation checklist. Use this list as a reference when performing an installation. For detailed installation instructions, refer to the Cisco ONS 15302 Installation and Operations Guide (Release 2.0). To check the installation, verify the following items:

ONS 15302 is mounted securely in the rack.

Power runs to the ONS 15302.

Transmit and receive fiber patch cords from the fiber termination are correctly connected to the ONS 15302.

Fiber-optic patch cords route through the rack.

Electrical cables route through the rack.

Each cable is labeled.

11 ONSCLI—ONS 15302 Command Line Interface

Introduction to ONSCLI

ONSCLI is a line-oriented ASCII-based management interface to ONS 15302. It is used to issue simple commands—possibly with parameter—to access or modify the ONS 15302 configuration.

Accessing ONSCLI

ONSCLI is accessed via the VT100-port or via an IP connection (Telnet). The serial connection communications parameters are fixed ( Table 2). VT100 terminal codes are used.

Table 2 EIA/TIA-232 Parameters

Parameter
Value

Speed

19200 bps

Data bits

8

Parity

None

Stop bits

1

Flow control

None


The VT100-port (Console port) for the ONS 15302 is provided using a RJ-45 connector.

Invoke an ONSCLI Session

An ONSCLI session is invoked by typing ONSCLI at the CLI terminal.

User authentication (a password containing between 8 and 12 ASCII characters, with no case sensitivity) is required, as the following session start-up sequence shows:

>
>ONSCLI

---------------------------------------------------
          ONS 15302 Command Line Interface
---------------------------------------------------

Enter ONSCLI password: ******

ONSCLI>


Note The default password for the ONS 15302 is ONSCLI.


Incorrect Password

Each password characters is echoed as *. An incorrect password is rejected with the message:

invalid password

After the password is rejected, the password prompt is re-issued.


Note The number of attempts is 3.


An authorized ONSCLI user has full access rights to the available management information.

Exit

The Exit command is used to terminate an ONSCLI session. The ONSCLI session is automatically terminated after a period of 30 minutes of inactivity. ONSCLI does not accept simultaneous sessions.

Syntax Rules

An ONSCLI command line begins with a prompt (issued by ONSCLI), which serves to indicate the current position in the command hierarchy.

An ONSCLI command is issued by typing the command followed by Enter. Optionally, and only at the lowest level in the command hierarchy, one or more parameters can also be supplied. These are identified by keywords. The command name, parameter keywords, and parameter values are delimited by one or more spaces. Command line editing features are listed in Table 3.


Note It is only necessary to type sufficient leading characters of the command name to avoid ambiguity—the same applies to keywords.


Table 3 Command Line Editing Features

Key
Result

Delete or Backspace

Erases the character in the command line.

Arrow left

Moves the cursor to the left side.

Arrow right

Moves the cursor to the right side.

Arrow Up

Recalls the previous command in command history.

Arrow Up

Recalls the previous command in command history.

Return or Enter

At the command line, processes a command.

..

Returns to the previous command level.

\

Goes to the top command level.

?

Issues a list of commands valid at the current level, or shows the command usage.


ONSCLI Commands are listed in Table 4

Table 4 ONSCLI Commands

Command
Result

Free

Shows VC-12 containers that are not yet utilized.

Used

Lists the VC-12 container(s) in use.

Status

Presents current device and port status.

Exit

Exits ONSCLI.


Some commands (in particular the show command) can potentially produce many lines of output. After a predetermined number of lines of output in response to a single command, the user is prompted to enter y(es) or n(o) to continue the output. The default line number limit is 23 and maximum is 998. For detailed information about the ONSCLI commands, refer to the Cisco ONS 15302 Installation and Operations Guide (Release 2.0).

Basic Command Syntax

A basic command has the syntax shown in Example 1.

Example 1 Basic Command Syntax

<basic command>::= [<path>]<command> [<parameter>]... <CR>
<path>::= [\]<command\>[<command>\]...
<command>::= <command name> |..
<parameter>::= <spaces> <keyword>=<value> |?
<value>::= <integer> |
							<choice> |
							<IP address> |
							<string> |
							<MAC address> |
							<NSAP address> |
							<time> |
							<date> |
							<KLM> |
							<portList> |
							<port>
<NSAP address>					::= <area address>:<system id>:<selector>
<portList>					::= <port>[,<port>]..
<areaAddressList>					::= <area address>[,<area address>]...

where:
<spaces>				is a string of one or more ASCII spaces;

<integer>				is a decimal integer in the range [m:n], where the values m and n are 
				context-dependent;

<choice>				is a literal string, whose permissible values and their significance are 
				context-dependent and may be obtained by using the help (?) parameter;

<IP address>				is an IP address of the form ddd.ddd.ddd.ddd, where d is a decimal digit. 
				Leading zeroes in each ddd may be omitted;

<string>				is a string of graphical ASCII characters, excluding quotation marks ("). 
				If the string contains one or more spaces, then it MUST be enclosed in 
				quotation marks. The maximum length of the string is context-dependent;

<MAC address>				is exactly 12 hexadecimal digits;

<time>				is a time-of-day of the form hh:mm:ss, where h, m and s are decimal digits;

<date>				is a date of the form dd/mm/yy, where d, m and y are decimal digits;
<KLM>				is a string of the form k.l.m, where k is a decimal digit in the range 
				[1:3], l is a decimal digit in the range [1:7], and m is a decimal digit 
				in the range [1:3]. 
<port>				is a decimal integer;
<area address>				is a hexadecimal string;
<system id>				is a hexadecimal string;
<selector>				is a hexadecimal string;

For a complete overview of the ONSCLI command hierarchy, please refer the Cisco ONS 15302 Installation and Operations Guide (Release 2.0).

The Help Command

The help command (?) displays all available commands at the current level, each with a short description. For example, typing? at the root level lists the commands that are available at this level, as shown in Example 2.

Example 2 Help Command

ONSCLI>?
*** current menu path:
<root>
*** valid commands:
Device:     Device configuration
Ports:      Port properties
Bridge:     Bridge/Spanning Tree Protocol settings
Router:     Router configuration
Security:   Security settings
Statistics: Performance monitoring and statistics
Services:   Utility functions
Alarms:     Current alarms and alarm history
QoS:        Quality of service
Running:    Show Running Config
Exit:       Exit from ONSCLI

Command Hierarchy

In the command hierarchy, the lowest level is represented by a basic command with one or more parameters.

If the help parameter (?) is supplied, then all other parameters are ignored and the basic command usage is displayed.

Table entries are accessed by introducing an additional command level giving access to the entire table. At this lowest level, the Add command (with the index and required table entries as parameters) can be used to add an element to the table and the Edit command can be used to replace an existing element in the table (if these operations are permitted on the table).

Similarly the Remove command (with the entry index as a parameter) can be used to remove an existing element from the table if this is permitted.

The Show command (with an entry index value as a parameter) displays the specified table entry. If no parameter is supplied with the Show command, the current contents of the entire table is displayed.

ONSCLI Error Messages

SNMP Errors

The general ONSCLI output string for SNMP errors is MIB access error. Additional SNMP error information might be printed depending on the return code ( Table 5).

Table 5 Additional ONSCLI SNMP Error Messages

Error Message (Output String)
Description

No Such Object

Scalar or table entry not found

End Of MIB View

End of table reached

No Creation

Creation of new entry failed

Not Writable

Accessed instance write protected

Wrong Length

Wrong specified field length

Wrong Value

Wrong value used for specified field

Inconsistent Value

Wrong value used for specified field

Resource Unavailable

Instance status not free for update

General Error

No additional error info

No Write To CDB

Write to Flash failed

Instance Exists

Table entry already exists


Input Errors

Error messages due to mistyping or incorrect ONSCLI input format are shown in Table 6.

Table 6 ONSCLI Input Error Messages 

Error Message (Output String)
Description

Unknown parameter specification

Input parameter incorrectly specified

Ambiguous parameter specification

Parameter value out of range

Multiple parameter specification

Input parameter specified twice

Missing parameter specification

Mandatory parameter missing

Incompatible parameter specification

Wrong combination of parameters

Missing value

Wrong formatted or empty input value

Invalid integer value

Wrong input integer value

Invalid choice value

Input value (set element name) not found

Invalid length of string value of

Input string too long

Badly-formed string value of

Input string incorrectly formatted

Invalid IP address

IP address incorrectly formatted

Invalid length of hex string

Length of hex string not according to input requirement

Invalid character in hex string

Hex value used to define a digit is out of range.

Invalid escape sequence in string

'\0' value detected inside the string

Bad value

Incorrectly formatted input value

Integer out of range

Input integer value is not within limits.

List too long

List of integers longer than 10

Badly-formed list

Incorrect integer value found in integer list

Table empty

No entries found in SNMP table

Element not in table

Specified entry not found in SNMP table

This command is not available in this release

Command not supported

No modification parameters found

Modification command with no modification values received


12 Initial Configuration

By following the guides below you should be able to do the most important configurations of ONS 15302.

Factory Preconfiguration

Since the ONS 15302 is a flexible product with a lot of possible network applications, the factory preconfiguration is limited when delivered. Ethernet ports 1 to 5 are members of VLAN 1, the aggregate (STM-1) is enabled, and one VC-12 container is allocated to the Ethernet WAN (port number 5). In addition, an entry in the SNMP community table is preconfigured so that when an IP address is assigned, the ONS 15302 is able to take advantage of the GUI element manager. This configuration persists, regardless of whether the WAN module is inserted or not.

Example 3 Restore Factory Settings

The factory settings can also be restored by use of the ONSCLI command:

ONSCLI>Device\Factory-Reset

This command will only restore the factory settings properly if the configuration is cleared before the command is given. To make sure reset configuration is done, following line appears on the system terminal when Factory-Reset command is given:

Are device configuration) erased (y/n)?

Important Commands

Follow the steps in this section to perform initial configuration of the ONS 15302. The following tasks are the most important tasks involved in the configuration of an ONS 15302:

System-Mode

Assign IP address

Define SNMPv1 community

Erase a community string

Assign an IP Address to the ONS 15302

The ONS 15302 supports remote management solutions by the means of Telnet and SNMP.The possibilities as regards connectivity can be rather advanced for the ONS 15302 so the only explained solution in this document is when directly connected the management-port (MNGT). For more information please refer the Cisco ONS 15302 Installation and Operations Guide (Release 2.0).

To achieve one of the above mentioned management solutions it is necessary to assign an IP-address, subnet-mask and if required a default-gateway address must be defined.

System Mode

In ONS 15302 R2.0 an additional management mode, system mode is added.The System mode has two options, ip and ipunnumbered.


ONSCLI>...\Management-Configuration\sys?
Usage: 
   System-Mode 
[SYSTEM-MODE=<ip|ipunnumbered>] 

System Mode - IP

ONSCLI>...\Management-Configuration\sys sys=ip
Change management configuration, are you sure? (y/n)?

Example 4 Assign an IP-address:

If system mode is ip the command for IP configuration is:

ONSCLI>Device\Management-Configuration\Management-Port\IP-Configuration IP-ADDRESS=193.69.136.104, 
SUBNET-MASK=255.255.255.0. 

System Mode - IP Unnumbered

ONSCLI>...\Management-Configuration\sys sys=ipunnum
Change management configuration, are you sure? (y/n)?

Example 5 Assign an IP-address:

If system mode is ipunnumbered the command for IP configuration is:

ONSCLI>Device\Management-Configuration\IP-Configuration IP-ADDRESS=193.69.136.104, SUBNET-MASK=255.255.255.0. 


Define SNMPv1 Community

Factory pre-configured community:

Manager: 	0.0.0.0
Community:	public
Access:	Super						
Traps:	Disabled

This is an insecure community, which enables all managers regardless of the IP-address for the SNMP manager to access the device with the community string "public".

To add your own community string please use the following command:

ONSCLI>Security\Community-Table\add manager=10.0.0.20 community=admin access=super traps=enable 	 
"Enter"

Erase a Community String

To remove a community string the following command can be used:

ONSCLI>Security\Community-Table\remove manager=0.0.0.0 community=public 	 
"Enter"


Note Please see the Cisco EdgeCraft User Guide for further configuration and management of ONS 15302.