Document ID: 12631
Updated: Jan 31, 2006
Cisco has announced the end of sale for the Cisco LocalDirector. For more information, refer to the LocalDirector 400 Series End-of-Life and End-of-Sale Notices and Product Bulletins.
Contents
Introduction
In most cases, it is easier and quicker to upgrade Cisco LocalDirector software with floppy disks. There are cases, however, in which you need to upgrade an image from a TFTP server, for instance, when using a LocalDirector model 417 which has no disk drives and can only be upgraded through the network.
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
The information in this document is based on Cisco LocalDirector.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.
Upgrading
Use this procedure to upgrade LocalDirector from a TFTP server:
-
Issue the boot image command when LocalDirector is in configuration mode.
boot image image_filename tftp_server_ip [port port]
-
To check whether the correct image was upgraded, issue the show version command.
You will see results similar to this example output:
LocalDirector 430 Version 3.3.4
Caution: To upgrade LocalDirector configured for failover mode, refer to
Upgrading
LocalDirector in Failover Mode. Unless your LocalDirector configuration
uses
stateful
failover, all existing connections are lost during a LocalDirector
upgrade. If your site does not use
stateful
failover, it is recommended that you perform the upgrade procedure when
the fewest users are affected.
Configuration
This output example demonstrates the procedure to upgrade LocalDirector from a TFTP server:
| LocalDirector 430 (Version 3.3.3) |
|---|
localdirector# show version
LocalDirector 430 Version 3.3.3
localdirector# configure terminal
localdirector(config) 3# boot image ld334.bin 172.18.183.249
confirm boot [N]:
saving image from flash
copying 279040 bytes
saving config from flash
writing image to flash
wrote 279040 bytes e.size=279040
writing the config to flash
confirm reboot on new image [N]:
remove floppy from drive and hit any key
Rebooting....
Finesse Bios V3.3
Booting Floppy
Loading from Flash
32MB RAM
Flash=AT29C040A @ 0x300
i82557 rev 2 Ethernet @ irq11 dev 13 index 0
MAC: 00a0.c965.576f
i82557 rev 2 Ethernet @ irq15 dev 14 index 1
MAC: 00a0.c965.5b33
Finesse BIOS V3.3
Booting Floppy
Loading from Flash
384MB RAM
i82557 rev 5 Ethernet @ irq11 dev 0 index 0 MAC: 00e0.b601.fa49
i82557 rev 5 Ethernet @ irq10 dev 1 index 1 MAC: 00e0.b601.fa48
i82557 rev 5 Ethernet @ irq15 dev 2 index 2 MAC: 00e0.b601.fa47
i82557 rev 5 Ethernet @ irq 9 dev 3 index 3 MAC: 00e0.b601.fa46
i82557 rev 5 Ethernet @ irq10 dev 0 index 4 MAC: 00e0.b602.dc2e
i82557 rev 5 Ethernet @ irq15 dev 1 index 5 MAC: 00e0.b602.dc2d
i82557 rev 5 Ethernet @ irq 9 dev 2 index 6 MAC: 00e0.b602.dc2c
i82557 rev 5 Ethernet @ irq11 dev 3 index 7 MAC: 00e0.b602.dc2b
Flash=AT29C040A @ 0x300
LocalDirector 430 Version 3.3.4 Initialization.....loading config....done.
Copyright (c) 1998-2000 by Cisco Systems, Inc.
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph>
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
localdirector> show version
LocalDirector 430 Version 3.3.4
|
Note: On the TFTP server that you are using, you should also see corresponding messages that indicate that the file was loaded correctly.
Related Information
Open a Support Case
(Requires a Cisco Service Contract.)
Related Cisco Support Community Discussions
The Cisco Support Community is a forum for you to ask and answer questions, share suggestions, and collaborate with your peers.
Refer to Cisco Technical Tips Conventions for information on conventions used in this document.
