The Cisco® Dense Wavelength-Division Multiplexing (DWDM) XFP pluggable module (Figure 1) allows enterprise companies and service providers to provide scalable and easy-to-deploy 10 Gigabit Ethernet services in their networks.
Figure 1. Cisco DWDM XFP Module
Main features of the Cisco DWDM XFP include:
• The Cisco DWDM XFP supports 10GBASE Ethernet.
• The hot-swappable input/output device plugs into an Ethernet XFP port of a Cisco switch or router to link the port with the network.
• The Cisco DWDM XFP supports the Cisco quality identification (ID) feature, which enables a Cisco switch or router to identify whether or not the module is an XFP module certified and tested by Cisco.
• The Cisco DWDM XFP supports 32 nontunable ITU 100-GHz wavelengths compatible with the Cisco ONS DWDM channel plan.
• The Cisco DWDM XFP supports digital optical monitoring capability.
Note: Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section.
Dimensions
• Dimensions (L x W x H): 71 x 18.5 x 8.5 mm. Cisco XFPs typically weigh less than 300 grams.
• Environmental Conditions and Power Requirements
• Operating temperature range: 32 to 158°F (0 to 70°C)
• Storage temperature range: -40 to 185°F (-40 to 85°C)
• The maximum power consumption per Cisco XFP module is 3.5W.
Optical Parameters
Table 1 shows the main optical characteristics for the Cisco DWDM XFP modules.
Table 1. Optical Parameters
Parameter
Symbol
Minimum
Typical
Maximum
Units
Notes and Conditions
Transmitter
Spectral width
0.2
nm
Full width, -20 dB from maximum, with resolution bandwidth (RBW) = 0.01 nm
Transmitter center wavelength
x - 100
x
x + 100
pm
Refer to Table 2 for center wavelengths
Side-mode suppression ratio
SMSR
30
dB
Transmitter extinction ratio
OMI
9
dB
Transmitter optical output power
Pout
-1.0
3.0
dBm
Average power coupled into single-mode fiber
Receiver
Receiver optical input wavelength
1530
1565
nm
Receiver damage threshold
4.0
dBm
Dispersion tolerance
-500
1600
ps/nm
Power-Limited Performance (measured at optical signal-to-noise ratio [OSNR] of 30 dB at 0.1-nm RBW)
Optical input power
Pin
-23.0
-7.0
dBm
See footnote*
Dispersion power penalty
3
dB
See footnote*
Noise-Limited Performance (measured at OSNR of 24 dB at 0.1-nm RBW)
Optical input power
Pin
-18.0
-7.0
dB
See footnote*
Dispersion OSNR penalty
3
dB
See footnote*
* At bit error rate (BER) = 1E-12 with IEEE802.3 test pattern.
Notes:
1. Parameters are specified over temperature and at end of life unless otherwise noted.
2. When shorter distances of single-mode fiber are used, an inline optical attenuator (10-dB) must be used to avoid overloading and damaging the receiver.
Warranty
Standard warranty: 90 days.
Ordering Information
Table 2 gives details about ordering Cisco DWDM XFPs.
Table 2. Cisco DWDM XFP Ordering Information
Product Number
Description
ITU Channel
DWDM-XFP-60.61=
10GBASE-DWDM 1560.61 nm XFP (100-GHz ITU grid)
21
DWDM-XFP-59.79=
10GBASE-DWDM 1559.79 nm XFP (100-GHz ITU grid)
22
DWDM-XFP-58.98=
10GBASE-DWDM 1558.98 nm XFP (100-GHz ITU grid)
23
DWDM-XFP-58.17=
10GBASE-DWDM 1558.17 nm XFP (100-GHz ITU grid)
24
DWDM-XFP-56.55=
10GBASE-DWDM 1556.55 nm XFP (100-GHz ITU grid)
26
DWDM-XFP-55.75=
10GBASE-DWDM 1555.75 nm XFP (100-GHz ITU grid)
27
DWDM-XFP-54.94=
10GBASE-DWDM 1554.94 nm XFP (100-GHz ITU grid)
28
DWDM-XFP-54.13=
10GBASE-DWDM 1554.13 nm XFP (100-GHz ITU grid)
29
DWDM-XFP-52.52=
10GBASE-DWDM 1552.52 nm XFP (100-GHz ITU grid)
31
DWDM-XFP-51.72=
10GBASE-DWDM 1551.72 nm XFP (100-GHz ITU grid)
32
DWDM-XFP-50.92=
10GBASE-DWDM 1550.92 nm XFP (100-GHz ITU grid)
33
DWDM-XFP-50.12=
10GBASE-DWDM 1550.12 nm XFP (100-GHz ITU grid)
34
DWDM-XFP-48.51=
10GBASE-DWDM 1548.51 nm XFP (100-GHz ITU grid)
36
DWDM-XFP-47.72=
10GBASE-DWDM 1547.72 nm XFP (100-GHz ITU grid)
37
DWDM-XFP-46.92=
10GBASE-DWDM 1546.92 nm XFP (100-GHz ITU grid)
38
DWDM-XFP-46.12=
10GBASE-DWDM 1546.12 nm XFP (100-GHz ITU grid)
39
DWDM-XFP-44.53=
10GBASE-DWDM 1544.53 nm XFP (100-GHz ITU grid)
41
DWDM-XFP-43.73=
10GBASE-DWDM 1543.73 nm XFP (100-GHz ITU grid)
42
DWDM-XFP-42.94=
10GBASE-DWDM 1542.94 nm XFP (100-GHz ITU grid)
43
DWDM-XFP-42.14=
10GBASE-DWDM 1542.14 nm XFP (100-GHz ITU grid)
44
DWDM-XFP-40.56=
10GBASE-DWDM 1540.56 nm XFP (100-GHz ITU grid)
46
DWDM-XFP-39.77=
10GBASE-DWDM 1539.77 nm XFP (100-GHz ITU grid)
47
DWDM-XFP-38.98=
10GBASE-DWDM 1538.98 nm XFP (100-GHz ITU grid)
48
DWDM-XFP-38.19=
10GBASE-DWDM 1538.19 nm XFP (100-GHz ITU grid)
49
DWDM-XFP-36.61=
10GBASE-DWDM 1536.61 nm XFP (100-GHz ITU grid)
51
DWDM-XFP-35.82=
10GBASE-DWDM 1535.82 nm XFP (100-GHz ITU grid)
52
DWDM-XFP-35.04=
10GBASE-DWDM 1535.04 nm XFP (100-GHz ITU grid)
53
DWDM-XFP-34.25=
10GBASE-DWDM 1534.25 nm XFP (100-GHz ITU grid)
54
DWDM-XFP-32.68=
10GBASE-DWDM 1532.68 nm XFP (100-GHz ITU grid)
56
DWDM-XFP-31.90=
10GBASE-DWDM 1531.90 nm XFP (100-GHz ITU grid)
57
DWDM-XFP-31.12=
10GBASE-DWDM 1531.12 nm XFP (100-GHz ITU grid)
58
DWDM-XFP-30.33=
10GBASE-DWDM 1530.33 nm XFP (100-GHz ITU grid)
59
Regulatory and Standards Compliance
Standards
• GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
• GR-326-CORE: Generic Requirements for Single-Mode Optical Connectors and Jumper Assemblies
• GR-1435-CORE: Generic Requirements for Multifiber Optical Connectors
Safety
• Laser Class I 21CFR1040
• Network Equipment Building Standards (NEBS) Level 3
For More Information
For more information about Cisco 10GBASE DWDM XFP modules, contact your sales representative.
