Feedback
|
Table Of Contents
Supported Devices Table for the CiscoWorks Wireless LAN Solution Engine, Release 2.7
Network Mangement—Supported Access Points and Bridges
Radio Management—Supported Access Points and Radios
Radio Management—Supported Client Adaptor Cards
Supported Devices Table for the CiscoWorks Wireless LAN Solution Engine, Release 2.7
Revised: 11/15/2005
The following sections show the Cisco devices supported when the CiscoWorks Wireless LAN Solution Engine, Release 2.7 was released:
•
Network Mangement—Supported Access Points and Bridges
•
Radio Management—Supported Access Points and Radios
•
Radio Management—Supported Client Adaptor Cards
To see a list of supported firmware versions, select Administration > System > Firmware Supported Versions.
To see a list of devices discovered by the Wireless LAN Solution Engine, select Devices > Discover > Managed Devices.
Non-IOS to IOS Conversions
For information on conversions from non-IOS to IOS, refer to the Conversion to IOS guide on Cisco.com: http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cwparent/cw_1105/wlse/2_7/index.htm.
Network Mangement—Supported Access Points and Bridges
Table 1 Supported Access Points and Bridges
Series SysObjectID Supported Firmware Versions Discovery, Inventory, Faults, Reporting Configuration FirmwareCisco Aironet 1100 series access points
1.3.6.1.4.1.9.1.507
12.2(4)JA, 12.2(4)JA1, 12.2(8)JA, 12.2(11)JA, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
12.2(4)JA, 12.2(4)JA1, 12.2(8)JA, 12.2(11)JA, 12.2(11)JA1, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
12.2(4)JA, 12.2(4)JA1, 12.2(8)JA, 12.2(11)JA, 12.2(11)JA1, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
Cisco Aironet 1210 and 1230 series (Cisco IOS) access points
1.3.6.1.4.1.9.1.525
12.2(8)JA, 12.2(11)JA, 12.2(11)JA1, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
12.2(8)JA, 12.2(11)JA, , 12.2(11)JA1, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
12.2(8)JA, 12.2(11)JA, 12.2(11)JA1, 12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA*
Cisco Aironet 1200 and 1220 series access points1
1.3.6.1.4.1.9.1.474
11.54T, 11.56, 12.01T1, 12.02T1, 12.03T, 12.04
12.01T1, 12.02T1, 12.03T, 12.04
11.54T, 11.56, 12.01T1, 12.02T1, 12.03T, 12.04
Cisco Aironet 350 series access points
1.3.6.1.4.1.9.1.380
11.21, 11.23T, 12.01T1, 12.02T1, 12.03T , 12.04
12.01T1, 12.02T1, 12.03T, 12.04
11.21, 11.23T, 12.01T1, 12.02T1, 12.03T, 12.04
Cisco Aironet 350 IOS series access points2
1.3.6.1.4.1.9.1.552
12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA
12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA
12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA
Cisco Aironet 340 series access points
1.3.6.1.4.1.9.1.379
11.21, 11.23T, 12.01T, 12.02T1, 12.03T, 12.04
12.01T1, 12.02T1, 12.03T, 12.04
11.21, 11.23T, 12.01T1, 12.02T1, 12.03T, 12.04
Cisco Aironet 350 series bridges
1.3.6.1.4.1.9.1.380
11.21, 11.23T, 12.01T, 12.02T1, 12.03T, 12.04
12.01T1, 12.02T1, 12.03T, 12.04
11.21, 11.23T, 12.01T1, 12.02T1, 12.03T, 12.04
Cisco Aironet 350 series workgroup bridges3
N/A
Not supported.
Not supported.
Not supported.
Cisco Aironet 1310 Wireless Bridges
1.3.6.1.4.1.9.1.565
12.2(15)JA, 12.2(15)JA1, 12.2(15)JA2
12.2(15)JA, 12.2(15)JA1, 12.2(15)JA2
12.2(15)JA
Cisco Aironet 1410 Wireless Bridges
1.3.6.1.4.1.9.1.533
12.2(15)JA
12.2(15)JA
12.2(15)JA
* 802.11g radios for Series 1100 and 1200 access points are supported only with 12.2(15)JA or later.
1 When a 1200 access point is converted to IOS, its SysObjectID and supported images correspond with the IOS 1210 and 1230 models.
2 Cannot be used as a WDS.
3 Workgroup bridges are discovered as clients.
Radio Management—Supported Access Points and Radios
Table 2 Radio Management Supported Access Points and Radios
Radio Management Feature Supported AP Models Supported Radios Minimum IOS Version RequiredRadio Monitoring,
AP Radio Scan,
Client Walkabout,
RM Assisted Configuration,
Self Healing,
Auto Re-Site Survey,
Location ManagerCisco Aironet 1100 series access points
.11b
12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA or later
.11g
12.2(15)JA or later
Cisco Aironet 1210 and 1230 series (Cisco IOS) access points
.11a
12.2(15)JA or later
.11b
12.2(13)JA1, 12.2.(13)JA2, 12.2(15)JA or later
.11g
12.2(15)JA or later
Cisco Aironet 350 IOS series access points1
.11b
12.2(13)JA, 12.2(13)JA1, 12.2(13)JA2, 12.2(13)JA3, 12.2(15)JA or later
Scanning-Only AP,
Client TrackingCisco Aironet 1100 series access points
.11b, .11g
12.2(15)JA or later
Cisco Aironet 1210 and 1230 series (Cisco IOS) access points
.11a, .11b, .11g
12.2(15)JA or later
1 Cannot be used as a WDS or Scanning-Only AP
Radio Management—Supported Client Adaptor Cards
Table 3 Radio Management Supported Client Adaptor Cards
Radio Management Feature Supported Client AdaptorsAll Radio Manager and Location Manager features1
AIR-PCI351x (Air350 based client card, B-radio)2
1 Requires CCX-V2 or later compliant clients. To check the status of partner client cards, see the CCX partner website at cetifid.http://www.cisco.com/en/US/partners/pr46/pr147/partners_pgm_concept_home.html
2 To allow the client adaptor to participate in the Radio Management feature, the Enable Radio Management Support parameter must be checked. This parameter, which is accessible from the Advanced (Infrastructure) Parameters screen in ACU, is available in:
2 - Windows ACU version 6.2 or later for 350 series client adapters using firmware version 5.30.17 or later
2 - Windows ACU version 6.3 or later for CB20A client adapters using firmware version 5.40.10 or later
4 Requires ADU software version 1.1 or later.
5 Includes both 802.11a and 802.11g radios. The 802.11g radio can act like a 802.11b radio (g is a superset of b), so effectively the AG client can operate in A, B, and G modes.
Supported Switches
Note
The WLSE monitors basic MIB-II attributes that are available on all switches. In general, different software versions of these devices will be supported because those attributes are not expected to change.
Table 4 Supported Switches
Series Devices Supported SysObjectIDCisco Catalyst 1200
1200
1.3.6.1.4.1.9.5.5
Cisco Catalyst 1900
1924
1.3.6.1.4.1.9.5.18
1.3.6.1.4.1.9.5.28
1912
1.3.6.1.4.1.9.5.175
1.3.6.1.4.1.9.5.31
Cisco PGW 2200 Softswitch
2200
1.3.6.1.4.1.9.5.13
Cisco Catalyst 2820
2820
1.3.6.1.4.1.9.5.20
Cisco Catalyst 29001
2980G-A
1.3.6.1.4.1.9.5.51
2980G
1.3.6.1.4.1.9.5.49
2948GL3Dc
1.3.6.1.4.1.9.1.386
2948G
1.3.6.1.4.1.9.5.42
2926
1.3.6.1.4.1.9.5.35
2900
1.3.6.1.4.1.9.5.12
Cisco Catalyst 2900XL2
2908XL
1.3.6.1.4.1.9.1.170
2912XL
1.3.6.1.4.1.9.1.219
2912MFXL
1.3.6.1.4.1.9.1.221
2916MXL
1.3.6.1.4.1.9.1.171
2924XL
1.3.6.1.4.1.9.1.183
2924CXL
1.3.6.1.4.1.9.1.184
2924XLV
1.3.6.1.4.1.9.1.217
2924CXLV
1.3.6.1.4.1.9.1.218
2924MXL
1.3.6.1.4.1.9.1.220
Cisco Catalyst 29503
2950-12
1.3.6.1.4.1.9.1.323
2950-24
1.3.6.1.4.1.9.1.324
2950-24C
1.3.6.1.4.1.9.1.325
2950T
1.3.6.1.4.1.9.1.359
2950-12G
1.3.6.1.4.1.9.1.427
2950-24G
1.3.6.1.4.1.9.1.428
2950-48G
1.3.6.1.4.1.9.1.429
2950-24S
1.3.6.1.4.1.9.1.430
2950-24GDC
1.3.6.1.4.1.9.1.472
Cisco Catalyst 3000 series switches
C3000
1.3.6.1.4.1.9.5.10
1.3.6.1.4.1.9.5.26
C3100
1.3.6.1.4.1.9.5.23
C3200
1.3.6.1.4.1.9.5.15
CPW16
1.3.6.1.4.1.9.5.9
1.3.6.1.4.1.9.5.25
Cisco Catalyst 3500 XL series switches4
3508GXL
1.3.6.1.4.1.9.1.246
3512XL
1.3.6.1.4.1.9.1.247
3524XL,
1.3.6.1.4.1.9.1.248
3548XL
1.3.6.1.4.1.9.1.278
3524PWRXL,
1.3.6.1.4.1.9.1.287
3524PWRXLEn
1.3.6.1.4.1.9.1.515
Cisco Catalyst 3550 series switches5
3550-24
1.3.6.1.4.1.9.1.366
3550-48
1.3.6.1.4.1.9.1.367
3550-12T
1.3.6.1.4.1.9.1.368
3550-12G
1.3.6.1.4.1.9.1.431
3550-24DC
1.3.6.1.4.1.9.1.452
3550-24-MMF
1.3.6.1.4.1.9.1.453
3550-24PWR
1.3.6.1.4.1.9.1.485
3550-24-PWR
1.3.6.1.4.1.9.1.485
Cisco Catalyst 3750 series switches
3750
1.3.6.1.4.1.9.1.516
3750-24TS
1.3.6.1.4.1.9.1.511
3750-248TS
1.3.6.1.4.1.9.1.512
3750G-24S
1.3.6.1.4.1.9.1.513
3750G-24T
1.3.6.1.4.1.9.1.514
Cisco Catalyst 3900 series switches
3900
1.3.6.1.4.1.9.5.33
3920
1.3.6.1.4.1.9.5.37
Cisco Catalyst 4000 series switches6
4003
1.3.6.1.4.1.9.5.40
4912G,
1.3.6.1.4.1.9.5.41
4006
1.3.6.1.4.1.9.5.46
4006-SW
1.3.6.1.4.1.9.1.448
4908gL3Dc
1.3.6.1.4.1.9.1.387
4503
1.3.6.1.4.1.9.1.501
Cisco Catalyst 4000 IOS series switches7
4006-SW
1.3.6.1.4.1.9.1.448
4503
1.3.6.1.4.1.9.1.501
4503-SUP
1.3.6.1.4.1.9.5.58
4506
1.3.6.1.4.1.9.1.502
4506-SUP
1.3.6.1.4.1.9.5.59
4507R
1.3.6.1.4.1.9.1.503
Cisco Catalyst 5000 series switches8
5000
1.3.6.1.4.1.9.5.7
5002
1.3.6.1.4.1.9.5.29
Cisco Catalyst 5500 series switches9
5500
1.3.6.1.4.1.9.5.17
5505
1.3.6.1.4.1.9.5.34
5509
1.3.6.1.4.1.9.5.36
Cisco Catalyst 6000* series switches10
6006
1.3.6.1.4.1.9.5.38
6009
1.3.6.1.4.1.9.5.39
6503
1.3.6.1.4.1.9.5.56
6506
1.3.6.1.4.1.9.5.45
6509
1.3.6.1.4.1.9.5.44
6509SP
1.3.6.1.4.1.9.5.47
6513
1.3.6.1.4.1.9.5.50
Cisco Catalyst 7600 Series
7603*
1.3.6.1.4.1.9.1.401
7606*
1.3.6.1.4.1.9.1.402
*The Wireless LAN Services Module (WSM) can be implemented in these switches to provides WDS to the wireless network.
1 Tested with Software Release 12.0(7)WX5(15a)
2 Tested with Software Release 11.2 (8.5)SA6
3 Tested with Software Release 12.0(5.3)WC(1) and 12.1(9)EA1
4 Tested with Software Release 12.0(5.3)WC(1), 12.0(5.2)XU
5 Tested with Software Release 12.1(6)EA1
6 Tested with Software Release 6.3 (3) and 7.2(2)
7 Tested with Software Release 12.1(12c)EW
8 Tested with Software Release 4.5(3)
9 Tested with Software Release 5.4(1)
10 Tested with Software Releases 6.2(2) and 6.3(1)
Supported Routers
Note
The WLSE monitors basic MIB-II attributes that are available on all switches. In general, different software versions of these devices will be supported because those attributes are not expected to change.
Table 5 Supported Routers
Series Devices Supported SysObjectIDCisco 800 series routers
801
1.3.6.1.4.1.9.1.212
802
1.3.6.1.4.1.9.1.213
803
1.3.6.1.4.1.9.1.214
804
1.3.6.1.4.1.9.1.215
804J
1.3.6.1.4.1.9.1.296
805
1.3.6.1.4.1.9.1.245
806
1.3.6.1.4.1.9.1.384
811
1.3.6.1.4.1.9.1.295
813
1.3.6.1.4.1.9.1.396
826
1.3.6.1.4.1.9.1.322
826 QuadV
1.3.6.1.4.1.9.1.321
827
1.3.6.1.4.1.9.1.284
827-H
1.3.6.1.4.1.9.1.446
827 QuadV
1.3.6.1.4.1.9.1.270
828
1.3.6.1.4.1.9.1.382
831
1.3.6.1.4.1.9.1.497
837
1.3.6.1.4.1.9.1.495
Cisco 1700 series routers
1710
1.3.6.1.4.1.9.1.200
1721
1.3.6.1.4.1.9.1.444
1760
1.3.6.1.4.1.9.1.416
Cisco 2600 series routers1
2610
1.3.6.1.4.1.9.1.185
2611
1.3.6.1.4.1.9.1.186
2612
1.3.6.1.4.1.9.1.187
2613
1.3.6.1.4.1.9.1.195
2620
1.3.6.1.4.1.9.1.208
2621
1.3.6.1.4.1.9.1.209
2650
1.3.6.1.4.1.9.1.319
2651
1.3.6.1.4.1.9.1.320
2691
1.3.6.1.4.1.9.1.413
2610XM
1.3.6.1.4.1.9.1.466
2611XM
1.3.6.1.4.1.9.1.467
2620XM
1.3.6.1.4.1.9.1.468
2621XM
1.3.6.1.4.1.9.1.469
2650XM
1.3.6.1.4.1.9.1.470
2651XM
1.3.6.1.4.1.9.1.471
Cisco 3600 series routers2
3620
1.3.6.1.4.1.9.1.122
3640
1.3.6.1.4.1.9.1.110
3660
1.3.6.1.4.1.9.1.205
3661-AC
1.3.6.1.4.1.9.1.338
3661-DC
1.3.6.1.4.1.9.1.339
3662-AC
1.3.6.1.4.1.9.1.340
3662-AC-CO
1.3.6.1.4.1.9.1.342
3662-DC
1.3.6.1.4.1.9.1.341
3662-DC-CO
1.3.6.1.4.1.9.1.343
1 Tested with Cisco IOS Software Release 12.2(1)
2 Tested with Cisco IOS Software Release 12.0(5)XK
Supported Access Servers
Table 6 Supported Access Servers
Devices Supported Versions Discovery, Inventory, Faults, Reporting Configuration and FirmwareLEAP, PEAP, RADIUS, and EAP-MD5 servers
Cisco Secure Access Control Server (ACS)1 , Versions 2.6.x, 3.0.x, 3.1.x, and 3.2
Not supported.
Cisco Access Registrar
Cisco Access Registrar (CAR), Version 1.7 and 3.0
Not supported.
1 The WLSE cannot perform Microsoft PEAP (EAP-MSCHAPv2) transactions with ACS.
Feedback